New Advanced Technology on Waste Resourcelization of the Black Pulping Liquor

Combining the characteristics of the black pulping liquor that contains a lot of lignin and other biomass resources, the technology of comprehensive waste utilization is employed. The reconstructive preparation of modified urea-formaldehyde glue by adding black pulping liquor and the application in extruding the medium density fibre board using this modified urea-formaldehyde glue is researched. Results show that when applying the preparation technology that alkaline reaction and then weak acid reaction, the appropriate preparation process is as follows： the adding urea process is divided into three stages （proportion 2 ： 1 ： 1） ; the pH value is 8.0, and the reaction time is 40 min in the addition reaction stage; the pH value will be naturally reduced to 3.5 -5.0, and the reaction time is 45 min in the aggregation reaction stage; the pH value is 8.0 in the urea complement stage. And the optimal condition of the reconstructive preparation the modified ureaformaldehyde glue is adding the condensed black pulping liquor after hydroxymethylation in the beginning of polycondensation reaction by 5% proportion. The application in extruding medium density fibre board with this modified urea-fosmaldehyde glue is proved feasible.

Combustion and Sulfur-fixing Performance of Pulping Black Liquor Coal-water Slurry

The effects of adding pulping black liquor and other additives to coal-water slurry(CWS) on the sulfur-fixing performance of the resultant mixture(pulping black liquor coal-water slurry) were evaluated. The experimental results demonstrated that the ash content of the black liquor coalwater slurry decreased as the addition of pulping black liquor in the mixture increased. Nevertheless, the addition amount should be appropriately selected to ensure that the black liquor coal-water slurry had a moderate calorific value. Addition of black liquor improved the combustion performance of CWS by lowering the ignition point and stabilizing the combustion process; moreover, the sulfur-fixation ratio after combustion increased by 12 to 16 percentage points than that of CWS, and the content of high-melting-point salt in the ash from CWS after adding black liquor was low. The sulfur-fixing ratio of CWS after adding a sulfur-fixing agent was effectively increased by 25 to 30 percenatge points, but with compromise of the fluidity and stability of the CWS; thus, the addition amount of a sulfur-fixing agent should be optimized.

Combined effect of US/PFS on the black liquor of making paper

The reed pulping black liquor is used as a sample. Researches of (1) combined effect of ultrasound(US)/polyferric sulphate(PFS)/hydrogen peroxide(H 2O 2); (2) effects of the horn tip areas; (3) effect of dose of PFS were carried. Extrapolation of these experiments indicated treatment results are possibly related to complex chemical compositions in the reed pulping black liquor.

Study on Synthesis of Nanometer SiC Precursors with Sol-Gel of SiO_2-Lignin in the Pulp Black Liquor

In the process of synthesis of nanometer SiC precursors with sol-gel of SiO2 and lignin , the products of all sizes required can be controlled by the concentration of reac-t ants , pH, temperature, reaction and ageing time , and so on . The best conditions in this research are : the concentration of Na2SiO3 and organic matters are 4. 50% and 26.4% respectively, pH = 3.3 , T = 65℃ , ageing time is 30min , dried at 150 ℃ , the size of SiC precursors is about 2.0μm .

Preparation of Adsorbent with Magnesium Sulfate and Straw Pulp Black Liquor and Its Phenol Adsorption Properties

A magnesia adsorbent was prepared from straw pulp black liquor and magnesium sulfate for the first time, and its adsorption of phenol from aqueous solution was examined. The characteristics of the adsorbent were tested through chemical analysis, surface analysis, X-ray diffraction and FT-IR spectroscopy. The effects of various factors, such as dose, adsorption time and adsorption temperature, on phenol adsorption behavior were studied. The results show that the adsorption processes can be fitted to the isotherm Langmuir model very well. It was found that the adsorption process was strongly influenced by temperature and the optimal temperature for phenol removal was 40 ℃. The optimum adsorption time was 10 min, and desorption would happen afterwards. Between the models of Langmuir and Freundlich, the adsorption process of phenol onto magnesia fitted the Langmuir equation better.