Optimization of the Air Deck Blasting Parameters on the Basis of the Holmquist-Johnson-Cook Constitutive Model

The present study considers the so-called air deck blasting,one of the most commonly used techniques for the improvement of blasting efficiency in mining applications.In particular,it aims to improve the operating conditions of large-scale equipment,increase the efficiency of the slope enlarging process,and reduce the mining cost.These objectives are implemented through a two-fold approach where,first,a program for slope enlarging based on the middle air-deck charge blasting-loosening technology is proposed,and second,the physical mechanism responsible for the stress wave attenuation in the rock is analyzed in the framework of a Holmquist–Johnson–Cook constitutive model.Field test results verify that the proposed approach is highly efficient and economical when used in medium-hard rock blasting and thus provides a basis for the practical implementation of slope enlargement for high benches in Open-Pit Mines.

Energy and blast performance of beryllium in a model thermobaric composition in comparison with aluminum and magnesium

A direct comparison is made between the effectiveness of Al,Mg,and Be powders as additional fuels in model thermobaric compositions containing 20%fuel,20%ammonium perchlorate,and 60%RDX(1,3,5-Trinitro-1,3,5-triazacyclohexane)passivated with wax.Experimentally determined calorimetric measurements of the heat of detonation,along with the overpressure histories in an explosion chamber filled with nitrogen,were used to determine the quasi-static pressure(QSP)under anaerobic conditions.Overpressure measurements were also performed in a semi-closed bunker,and all blast wave parameters generated after the detonation of 500 g charges of the tested explosives were determined.Detonation calorimetry results,QSP values,and blast wave parameters(pressure amplitude,specific and total impulses)clearly indicate that Be is much more effective as an additional fuel than either Al or Mg in both anaerobic post-detonation reactions as well as the subsequent aerobic combustion.The heat of detonation of the RDXwax/AP/Be explosive mixture is over 40%and 50%higher than that of the mixture containing aluminum and magnesium instead of beryllium,respectively.Moreover,the TNT equivalent of the Be-containing composition due to the overpressure in the nitrogen-filled explosion chamber is 1.66,while the equivalent calculated using an air shock wave-specific impulse at a distance of 2.5 m is equal to 1.69.The high values of these parameters confirm the high reactivity of beryllium in both the anaerobic and aerobic stages of the thermobaric explosion.

Analysis and Optimization of Blasting Practices at the Sangaredi Mine

Generally, the Mos hardness of bauxite is 2.5 to 3.5. According to the specific conditions of the Sangaredi bauxite deposit, that is, the rock hardness coefficient is between 3 and 6, and there is a clayey zone in the bauxite mining area, it is necessary to carry out blasting work before mining. This article mainly analyzes and optimizes the blasting practice of the Sangaredi open pit bauxite mine. The subject was finally extended to the reduction of nuisances due to blasting, that is to say essentially due to vibrations: this presupposed a study around the vibration data available, and the proposal of methods to limit these vibrations. The bottom conditions of the Sangaredi bauxite ore zone are studied. Bauxite reserves are very rich and the market is huge. The analysis of mine blasting practices, mainly the types of explosives, the selection and analysis of explosives and blasting equipment and choosing the mode of longitudinal blasting, the link of the blasting site of the mining area, further study the optimization of mining blasting practice, the choice of drilling and process to determine reasonable blasting parameters, which improving the drilling method. The experimental results show that this optimization scheme improves efficiency blasting of the bauxite mine but also promotes an increase in production.

Measurement-while-drilling technique and its scope in design and prediction of rock blasting

With rampant growth and improvements in drilling technology, drilling of blast holes should no longer be viewed as an arduous sub-process in any mining or excavation process. Instead, it must be viewed as an important opportunity to quickly and accurately measure the geo-mechanical features of the rock mass on-site, much in advance of the downstream operations. It is well established that even the slightest variation in lithology, ground conditions, blast designs vis-a-vis geologic features and explosives performance, results in drastic changes in fragmentation results. Keeping in mind the importance of state-of-the-art measurement-while-drilling （MWD） technique, the current paper focuses on integrating this technique with the blasting operation in order to enhance the blasting designs and results. The paper presents a preliminary understanding of various blasting models, blastability and other related concepts, to review the state-of-the-art advancements and researches done in this area. In light of this, the paper highlights the future needs and implications on drill monitoring systems for improved information to enhnnrp th~ hl^tin~ r^HIt~

Blast performance of layered charges enveloped by aluminum powder/rubber composites in confined spaces

A layered charge composed of the JH-2 explosive enveloped by a thick-walled cylindrical casing(active aluminum/rubber and inert lithium fluoride/rubber composites) was designed and explosion experiments were conducted in a 1.3 m3tank and a 113 m3bunker.The blast parameters,including the quasistatic pressure(ΔpQS),special impulse(I),and peak overpressure(Δpmax),and images of the explosion process were recorded,and the influence of the Al content(30% and 50%) and Al particle size(1,10,and 50 μm) on the energy release of aluminum/rubber composites were investigated.The results revealed that the use of an active layer increased the peak overpressure generated by the primary blast wave,as well as the quasistatic pressure and special impulse related to fuel burning within tens of milliseconds after detonation.When the Al content was increased from 30% to 50%,the increases of ΔpQS and I were not obvious,and Δpmaxeven decreased,possibly because of decreased combustion efficiency and greater absorption of the blast wave energy for layers with 50% Al.Compared with the pure JH-2charge,the charge with 1 μm Al particles produced the highest Δpmax,indicating that better transient blast performance was generated by smaller Al particles.However,the charge with 10 μm Al particles showed the largest ΔpQSand I,suggesting that a stronger destructive effect occurred over a longer duration for charges that contained moderate 10 μm Al.