Criterion for Blind Signals Separation Based on Correlation Function

Blind separation of source signals usually relies either on the condition of statistically independence or involving their higher-order cumulants. The model of two channels signal separation is considered. A criterion based on correlation functions is proposed. It is proved that the signals can be separated, using only the condition of noncorrelation. An algorithm is derived, which only involves the solution to quadric nonlinear equations.

A HOS-based Blind Signal Extraction Method for Chaotic MIMO Systems

A novel method to extract multiple input and multiple output (MIMO) chaotic signals was proposed using the blind neural algorithm after transmitting in nonideal channel. The MIMO scheme with different chaotic signal generators was presented. In order to separate the chaotic source signals only by using the sensor signals at receivers, a blind neural extraction algorithm based on higher-order statistic (HOS) technique was used to recover the primary chaotic signals. Simulation results show that the proposed approach has good performance in separating the primary chaotic signals even under nonideal channel.

BLIND SIGNAL SEPARATION OF LINEAR MIXTURE USING TRILINEAR DECOMPOSITION

This paper introduces a new source separation technique exploiting the time coherence of the source signals. The proposed approach relies only on stationary second order statistics. Blind Signal Separation (BSS) method using trilinear decomposition is proposed in this paper. Simulation results reveal that our proposed algorithm has the better blind signal separation performance than joint diagonalization method. Our proposed algorithm does not require whitening processing. Moreover, our proposed algorithm works well in the underdetermined condition, where the number of sources exceeds than the number of sensors.

BLIND SIGNAL SEPARATION BASED ON ME AND STATISTICAL ESTIMATION

There are two major approaches for Blind Signal Separation (BSS) problem: Maximum Entropy (ME) and Minimum Mutual Information (MMI) algorithms. Based on the recursive architecture and the relationship between the ME and MMI algorithms, an Extended ME(EME) algorithm is proposed by using probability density function (pdf) estimation of the outputs to deduce the corresponding iterative formulas in BSS. Based on the simulation results, it can be concluded that the proposed algorithm has better performances than the traditional ME algorithm in convolute mixture BSS problems.

BSP:Ⅱ- Blind Signals Separation

ＢＳＰ：Ⅱ－ＢｌｉｎｄＳｉｇｎａｌｓＳｅｐａｒａｔｉｏｎ￥Ｒｕｅｙ－ｗｅｎＬｉｕ（ＵｎｉｖｅｒｓｉｔｙｏｆＮｏｉｒｅＤａｍｅ，ＮｏｉｒｅＤａｍｅ，ＩＮ４６５５６）Ａｂｓｔｒａｃｔ：ＴｈｅＰｒｏｂｌｅｍｏｆｂｌｉｎｄｓｉｇｎａｌｓｅｐａｒａｔｉｏｎａｎ...

Data-Driven Joint Estimation for Blind Signal Based on GA-PSO Algorithm

Without any prior information about related wireless transmitting nodes,joint estimation of the position and power of a blind signal combined with multiple co-frequency radio waves is a challenging task.Measuring the signal related data based on a group distributed sensor is an efficient way to infer the various characteristics of the signal sources.In this paper,we propose a particle swarm optimization to estimate multiple co-frequency"blind"source nodes,which is based on the received power data measured by the sensors.To distract the mix signals precisely,a genetic algorithm is applied,and it further improves the estimation performance of the system.The simulation results show the efficiency of the proposed algorithm.

Blind Signal Processing: I-Fundamental Concepts

ＢｌｉｎｄＳｉｇｎａｌＰｒｏｃｅｓｓｉｎｇ：Ｉ－ＦｕｎｄａｍｅｎｔａｌＣｏｎｃｅｐｔｓ￥Ｒｕｅｙ－ｗｅｎＬｉｕ（Ｄｅｐｔ．ｏｆＥｌｅｃｔｒｉｃａｌＥｎｇｉｎｅｅｒｉｎｇ，ＵｎｉｖｅｒｓｉｔｙｏｆＮｏｉｒｅＤａｍｅ，ＮｏｉｒｅＤａｍｅ，ＩＮ４６５５６）...

Neural Blind Beamformer for Cyclostationary Signals

A blind beamforming algorithm based on a neural network is presented according to the characteristic of cyclostationary signals. This method transforms the question of estimating beamformer weight vectors into the one of computing the SVD of the cross correlation matrix of array input signals and their frequency shift signals. A cross correlation neural network is introduced to compute the SVD of the cross correlation matrix so as to reduce the computational complexity and carry out the blind beanfforming more efficiently. The improved cross-coupled Hebbian learning rule presented can make the weights of the neural network converge much fast. Therefore, it is more promising in the practical use. This method can restrain noise and interference, simulation proves its correctness.

Approach to blind estimation of the PN sequence in DS-SS signals with residual carrier

This paper presents an approach of singular value de- composition plus digital phase lock loop to solve the difficult problem of blind pseudo-noise （PN） sequence estimation in low signal to noise ratios （SNR） direct sequence spread spectrum （DS-SS） signals with residual carrier. This approach needs some given parameters, such as the period and code rate of PN sequence. The received signal is firstly sampled and divided into non-overlapping signal vectors according to a temporal window, whose duration is two periods of PN sequence. An autocorrelation matrix is then computed and accumulated by those signal vectors one by one. The PN sequence with residual carrier can be estimated by the principal eigenvector of the autocorrelation matrix. Further more, a digital phase lock loop is used to process the estimated PN sequence, it estimates and tracks the residual carrier and removes the residual carrier in the end. Theory analysis and computer simulation results show that this approach can effectively realize the PN sequence blind estimation from the input DS-SS signals with residual carrier in lower SNR.

动态变化混叠模型下盲源分离中的源数估计

在进行欠定盲分离时,特别是对于源信号数目及混合矩阵动态变化的情况,常规的欠定盲分离及源数估计方法不能对源信号数目的变化时刻做出判断,因此很难实现动态变化的源信号数目实时和准确的估计。针对这个问题,提出了一种动态变化混叠模型下欠定盲源分离中的源数估计方法。首先,建立动态变化混叠情形下盲源分离的数学模型及动态标识矩阵。其次,基于构建的动态标识矩阵统计和判断动态源信号数目的变化情况。最后,通过分段时间内多维观测矢量采样点聚类区间局部峰值统计,实现动态变化混叠模型下盲源分离中的源信号数目的有效估计。仿真结果表明,该方法能有效实现动态变化混叠模型下欠定盲源分离中的源数估计,并且信号估计效果良好。

基于双阵元天线的ADS-B解交织投影算法

随着广播式自动相关监视(Automatic Dependent Surveil lance-Broadcast,ADS-B)技术的普及,交通密集区域内多条ADS-B信号的交织问题难以避免。为了降低设备成本并提高系统在低成本条件下的可用性,针对双阵元天线三条ADS-B信号交织问题,提出了双阵元天线投影算法。首先,上述方法基于频域插值理论与最小描述长度准则进行信源数估计;然后,采用功率倒置算法进行空域滤波,在未知信号波达方向的条件下抑制非期望信号,从而将双天线三信号的解交织问题转化为单天线双信号的解交织问题;最后,由虚拟多通道法扩维后,基于改进的投影算法分离交织信号。仿真验证了以上算法的有效性。

带残余频偏的软扩频信号伪码序列盲估计

针对带残余频偏的软扩频信号伪码序列盲估计难的问题,提出一种奇异值分解(singular value decomposition,SVD)结合全数字锁相环(digital phase locked loop,DPLL)的方法。所提方法首先对待处理信号通过不重叠分段生成数据矩阵,每段信号长度为一倍伪码周期;然后利用其自相关矩阵的右上角元素估计失步点进行同步,并且在重新计算自相关矩阵后根据较大特征值个数估计进制数;最后通过多次快速SVD算法结合DPLL最终实现伪码序列的盲估计。仿真结果显示,所提方法在低信噪比条件下可以有效估计出带残余频偏的软扩频信号的伪码序列,并且性能优于其他对比方法。

针对冲击性故障信号的谱融合特征提取算法

利用盲解卷积方法在时域中进行故障信号特征提取时,常会出现多个信号混淆分离结果,但以往的研究中只强调了分离的部分,而很少对分离后的信号进行进一步的处理,给实际应用造成不便。这里在盲解卷积和谱融合的基础之上,使用核改进的模糊c均值聚类算法,针对机械故障信号的脉冲特性,提出一种针对冲击性故障信号处理的实用型算法。计算机仿真实验证实了该算法的有效性。此算法优化了以往的聚类筛选方法,可以有效排除反卷积后诸多无用信号的干扰,将故障脉冲信号的特征准确提取出来,能提高故障诊断的效率。

一种卫星隐蔽通信信号盲分离算法

重构抵消算法是卫星隐蔽通信信号分离的关键技术,算法的性能主要依赖于参数估计的精度。然而在实际环境中,参数估计误差带来的算法性能损失无法被避免。此外,对信号的重构使得该算法计算复杂度较高。针对这个问题,首先分析了参数估计误差对分离性能的影响,然后提出基于盲均衡算法的协作分离算法,提升信号分离性能的同时降低了算法的计算量。仿真实验表明,新算法相较于重构抵消算法,降低了对参数估计精度的依赖,当参数估计误差大于0.05时,信号的解调误码率降低了一个数量级左右。

基于参数估计和Kalman滤波的单通道盲源分离算法

针对存在频谱混叠通信信号的单通道盲源分离(single channel blind source separation,SCBSS)问题,提出一种基于参数估计和Kalman滤波的SCBSS算法。首先,针对根多重信号分类(root multiple signal classification,Root-MUSIC)算法在相近载频估计方面的局限性,提出一种自适应的Root-MUSIC算法,对接收到的盲混合信号的源信号数目和载频进行估计;其次,将Kalman滤波的思想引入到SCBSS算法中,根据估计得到的源信号参数构造信号模型,将其作为Kalman滤波系统的观测向量,执行“时间更新”和“测量更新”两个过程,得到源信号的最佳估计,实现单通道盲源分离。仿真结果表明,所提算法能够有效地从存在频谱混叠的单路接收信号中准确地分离出多路源信号,比传统的算法分离精度高,运算速度快。

基于SVD-K-means算法的软扩频信号伪码序列盲估计

针对通信中软扩频信号伪码序列盲估计困难的问题,提出一种奇异值分解(singular value decomposition,SVD)和K-means聚类相结合的方法。该方法先对接收信号按照一倍伪码周期进行不重叠分段构造数据矩阵。其次对数据矩阵和相似性矩阵分别进行SVD完成对伪码序列集合规模数的估计、数据降噪、粗分类以及初始聚类中心的选取。最后通过K-means算法优化分类结果,得到伪码序列的估计值。该算法在聚类之前事先确定聚类数目,大大减少了迭代次数。同时实验结果表明,该算法在信息码元分组小于5 bit,信噪比大于-10 dB时可以准确估计出软扩频信号的伪码序列,性能较同类算法有所提升。

基于循环维纳滤波器的声学成像优化方法

针对混响环境中背景噪声干扰导致循环平稳源重建精度不高的问题,基于循环维纳滤波器,结合贝叶斯近场声全息技术,提出了一种声学成像优化方法。通过麦克风阵列在声源的近场测量由声源辐射信号的声压,利用循环维纳滤波器对测量值进行去噪,从而实现对循环平稳信号的盲提取,再应用贝叶斯近场声全息技术在空间上重建循环平稳源。首先,通过仿真分析,系统地评估了盲信号提取算法的有效性。然后,通过开展声源重建实验,进一步验证了该声学成像优化方法的可行性。

基于JADE-斜投影的鲁棒波束形成算法

针对矩阵重构类波束形成算法对阵列幅相误差敏感的问题,提出一种基于盲源信号分离和斜投影的矩阵重构鲁棒波束形成算法。首先,依靠盲源分离技术得到接收信号和混合矩阵,结合期望信号先验信息完成混合矩阵中信号导向矢量的搜索。然后,利用盲源分离得到的信号协方差矩阵完成阵列幅相误差估计。最后,基于幅相误差校准的混合矩阵和斜投影思想,构建各干扰的斜投影算子,将接收数据分别向干扰斜投影空间进行投影,得到对应的干扰信号,完成干扰噪声协方差矩阵重构。仿真结果表明,所提方法对阵列幅相误差具有较好的鲁棒性,验证了算法的有效性。

FCM-FastICA的点蚀声发射信号分离识别方法

金属点蚀是一种破坏性和隐患较大的设备损伤形式。点蚀会产生声发射信号。点蚀过程中产生的多种声源类型会造成信号混叠,影响腐蚀进程的判断。针对点蚀信号混叠问题,提出一种模糊C均值聚类与快速独立分量分析算法相结合的点蚀信号分离识别方法。通过分析单、双点蚀声发射数据将点蚀分为钝化膜破裂阶段、点蚀诱导成核及发展阶段,由聚类确定信号类别并用快速独立分量分析分离混合信号,利用相关性函数验证分离效果。结果表明:单点蚀过程存在3类原信号,双点蚀过程存在7类信号,其中包含单个信号与混合信号;单个信号与原信号相关性极高,达到0.8以上,混合信号的分离分量与原信号相关性达到0.6以上,分离效果较好。该方法可对点蚀混合信号进行有效分离和识别,为腐蚀进程判断提供支持。