Based on turbulent theory, a 3D coupled model of fluid flow and solidification was built using finite difference method and used to study the influence of superheating degree and casting speed on fluid flow and solidi...Based on turbulent theory, a 3D coupled model of fluid flow and solidification was built using finite difference method and used to study the influence of superheating degree and casting speed on fluid flow and solidification, analyze the interaction between shell and molten steel, and compare the temperature distribution under different technological conditions. The results indicate that high superheating degree can lengthen the liquid-core depth and make the crack and breakout possible, so suitable superheating should be controlled within 35℃ according to the simulation results. Casting speed which is one of the most important technological parameters of improving production rate, should be controlled between 0. 85 m/min and 1.05 m/min and the caster has great potential in the improvement of blank quality.展开更多
The aim of this study was to simulate the solidification process of beam blank continuous casting, and then find the reasons for the typical defects of the beam blank. A two-dimensional transient coupled finite elemen...The aim of this study was to simulate the solidification process of beam blank continuous casting, and then find the reasons for the typical defects of the beam blank. A two-dimensional transient coupled finite element model has been developed to compute the temperature and stress profile in beam blank continuous casting. The enthalpy method was used in the heat conduction equation. The thermo-mechanical property in the mushy zone was taken into consideration in this calculation. It is shown that at the mold exit the thickness of the shell had its maximum value at the flange tip and its minimum value at the fillet. The temperature had a great fluctuation on the surface of the beam blank in the secondary cooling zone. At the unbending point, the surface temperature of the web was in the brittleness temperature range under the present condition. To ensure the quality, it is necessary to weaken the intensity of secondary cooling. At the mold exit the equivalent stress and strain have higher values at the flange tip and at the web. From the spray 1 to the unbending point, the maximum values of stress and strain gradually moved to the internal section of the flange tip and the web. However, whenever, there were bigger stress and strain values near the flange tip and the web than in the other parts, it must be very easy to generate cracks at those positions. Now, online verification of this simulation has been developed, which has proved to be very useful and efficient to instruct the practical production of beam blank continuous casting.展开更多
According to turbulent theory and characteristics of beam blank continuous casting, 3-D model to represent the flow of beam blank mould is established. The predicted results indicate that the exit obliquity of up 15&#...According to turbulent theory and characteristics of beam blank continuous casting, 3-D model to represent the flow of beam blank mould is established. The predicted results indicate that the exit obliquity of up 15°(+15°) should be adopted, which will benefit the floatation of non-metallic inclusion and purification of the molten steel. When the nozzle angle is 120°, the flow pattern is reasonable. Proper nozzle depth can be 200mm. Turbulent kinetic of meniscus can be reduced by adopting the square nozzle and suitable area of side outlet when casting speed increases. The results are consistent with those of water model experiment, so the model is exact and reasonable. The model can provide important information for design of SEN and defining of immersion depth.展开更多
This review paper aims to summarize cardiac CT blooming artifacts,how they present clinically and what their root causes and potential solutions are.A literature survey was performed covering any publications with a s...This review paper aims to summarize cardiac CT blooming artifacts,how they present clinically and what their root causes and potential solutions are.A literature survey was performed covering any publications with a specific interest in calcium blooming and stent blooming in cardiac CT.The claims from literature are compared and interpreted,aiming at narrowing down the root causes and most promising solutions for blooming artifacts.More than 30 journal publications were identified with specific relevance to blooming artifacts.The main reported causes of blooming artifacts are the partial volume effect,motion artifacts and beam hardening.The proposed solutions are classified as high-resolution CT hardware,high-resolution CT reconstruction,subtraction techniques and post-processing techniques,with a special emphasis on deep learning(DL)techniques.The partial volume effect is the leading cause of blooming artifacts.The partial volume effect can be minimized by increasing the CT spatial resolution through higherresolution CT hardware or advanced high-resolution CT reconstruction.In addition,DL techniques have shown great promise to correct for blooming artifacts.A combination of these techniques could avoid repeat scans for subtraction techniques.展开更多
文摘Based on turbulent theory, a 3D coupled model of fluid flow and solidification was built using finite difference method and used to study the influence of superheating degree and casting speed on fluid flow and solidification, analyze the interaction between shell and molten steel, and compare the temperature distribution under different technological conditions. The results indicate that high superheating degree can lengthen the liquid-core depth and make the crack and breakout possible, so suitable superheating should be controlled within 35℃ according to the simulation results. Casting speed which is one of the most important technological parameters of improving production rate, should be controlled between 0. 85 m/min and 1.05 m/min and the caster has great potential in the improvement of blank quality.
基金supported by the Hebei Provincial Natural Science Foundation of China(No.E2007000591).
文摘The aim of this study was to simulate the solidification process of beam blank continuous casting, and then find the reasons for the typical defects of the beam blank. A two-dimensional transient coupled finite element model has been developed to compute the temperature and stress profile in beam blank continuous casting. The enthalpy method was used in the heat conduction equation. The thermo-mechanical property in the mushy zone was taken into consideration in this calculation. It is shown that at the mold exit the thickness of the shell had its maximum value at the flange tip and its minimum value at the fillet. The temperature had a great fluctuation on the surface of the beam blank in the secondary cooling zone. At the unbending point, the surface temperature of the web was in the brittleness temperature range under the present condition. To ensure the quality, it is necessary to weaken the intensity of secondary cooling. At the mold exit the equivalent stress and strain have higher values at the flange tip and at the web. From the spray 1 to the unbending point, the maximum values of stress and strain gradually moved to the internal section of the flange tip and the web. However, whenever, there were bigger stress and strain values near the flange tip and the web than in the other parts, it must be very easy to generate cracks at those positions. Now, online verification of this simulation has been developed, which has proved to be very useful and efficient to instruct the practical production of beam blank continuous casting.
文摘According to turbulent theory and characteristics of beam blank continuous casting, 3-D model to represent the flow of beam blank mould is established. The predicted results indicate that the exit obliquity of up 15°(+15°) should be adopted, which will benefit the floatation of non-metallic inclusion and purification of the molten steel. When the nozzle angle is 120°, the flow pattern is reasonable. Proper nozzle depth can be 200mm. Turbulent kinetic of meniscus can be reduced by adopting the square nozzle and suitable area of side outlet when casting speed increases. The results are consistent with those of water model experiment, so the model is exact and reasonable. The model can provide important information for design of SEN and defining of immersion depth.
基金Research reported in this publication was supported by the National Heart,Lung,And Blood Institute of the National Institutes of Health,No.R01HL151561The content is solely the responsibility of the authors and does not necessarily represent the official views of the NIH.
文摘This review paper aims to summarize cardiac CT blooming artifacts,how they present clinically and what their root causes and potential solutions are.A literature survey was performed covering any publications with a specific interest in calcium blooming and stent blooming in cardiac CT.The claims from literature are compared and interpreted,aiming at narrowing down the root causes and most promising solutions for blooming artifacts.More than 30 journal publications were identified with specific relevance to blooming artifacts.The main reported causes of blooming artifacts are the partial volume effect,motion artifacts and beam hardening.The proposed solutions are classified as high-resolution CT hardware,high-resolution CT reconstruction,subtraction techniques and post-processing techniques,with a special emphasis on deep learning(DL)techniques.The partial volume effect is the leading cause of blooming artifacts.The partial volume effect can be minimized by increasing the CT spatial resolution through higherresolution CT hardware or advanced high-resolution CT reconstruction.In addition,DL techniques have shown great promise to correct for blooming artifacts.A combination of these techniques could avoid repeat scans for subtraction techniques.
