Optimization Study of Active-Passive Heating System Parameters in Village Houses in the Southern Xinjiang Province

Aiming at the problems of large energy consumption and serious pollution of winter heating existing in the rural buildings in Southern Xinjiang,a combined active-passive heating system was proposed,and the simulation software was used to optimize the parameters of the system,according to the parameters obtained from the optimization,a test platform was built and winter heating test was carried out.The simulation results showed that the thickness of the air layer of 75 mm,the total area of the vent holes of 0.24 m^(2),and the thickness of the insulation layer of 120 mm were the optimal construction for the passive part;solar collector area of 28 m^(2),hot water storage tank volume of 1.4 m^(3),mass flow rate of 800 kg/h on the collector side,mass flow rate of 400 kg/h on the heat exchanger side,and output power of auxiliary heat source of 5∼9 kWwere the optimal constructions for active heating system.Test results showed that during the heating period,the system could provide sufficient heat to the room under different heating modes,and the indoor temperature reached over 18°C,which met the heating demand.The economic and environmental benefits of the system were analyzed,and the economic benefits of the systemwere better than coal-fired heating,and the CO_(2) emissionswere reduced by 3,292.25 kg compared with coalfiredheating.The results of the study showed that the combinedactive-passiveheating systemcouldeffectively solve the heating problems existing in rural buildings in Southern Xinjiang,and it also laid the theoretical foundation for the popularization of the combined heating systems.

Feasibility Analysis on the Integrated Application of Solar Energy, Biogas, Coal-fired Boiler and Radiant Floor Heating for Rural Residence

The feasibility of adopting a balanced energy mix mode (domestic solar energy, biogas, coal-fired boiler and radiant floor heating) was proposed. Taking a typical rural residence in Zhengzhou City for example, the study through theoretical analysis and calculation showed that such a balanced energy mix is an economic way and efficient in saving energy and reducing air pollution, and elaborated the theoretical feasibility of popularizing such a heat supply mode in rural areas.

On-Line Life Monitoring Technique for Tube Bundles of Boiler High-Temperature Heating Surface

High-temperature heating surface such as superheater and reheater of large-sized utility boiler all experiences a relatively severe working conditions. The failure of boiler tubes will directly impact the safe and economic operation of boiler. An on-line life monitoring model of high-temperature heating surface was set up according to the well-known L-M formula of the creep damages. The tube wall metal temperature and working stress was measured by on-line monitoring, and with this model, the real-time calculation of the life expenditure of the heating surface tube bundles were realized. Based on the technique the on-line life monitoring and management system of high-temperature heating surface was developed for a 300 MW utility boiler. An effective device was thus suggested for the implementation of the safe operation and the condition-based maintenance of utility boilers.

A simulation Study on the System Combined Solar Energy with Biogas Boiler for Floor Radiant Heating and Fuel

A mathematical model was built for simulating an innovative design system combined solar energy with biogas boiler for floor radiant heating and fuel. Effects of the ambient air temperature on the performance of the system had been examined. And the results also support theoretical feasibility of the system.

Heating and Cooling Hybrid System with Gas Mixture Sourced Heat Pump and Heating Boiler

Preliminary investigation shows that air sourced type heat pumps by energy efficiency are competitive with gas boilers having 93% of coefficient of performance （COP） if heat pumps are used in climatic zones, having outside air temperature higher than （-3 ℃ to -5 ℃）. But, in such conditions the heat pump＇s evaporator is covered by ice crust, which cuts off the flow of outside air-heat source through the evaporator of heat pump. For avoiding stating problems it is recommended to use as heat source a mixture of waste warm gases. In this article a high efficiency heating-cooling system is developed, consisting of warm gases mixture sourced heat pump, heating boiler operating simultaneously with heat pump and solar air heater. The heating demand of the served house is shared between boiler and heat pump. Instead of outside air the warm gases mixture enters into evaporator of heat pump. A new construction of heat exchanger was developed. The article presents the structure and principle of operation, as well as the method for optimization and design of suggested system. Analysis proved high energy efficiency and cost effectiveness of the new system.

GB/T 24747-2023《有机热载体安全技术条件》国家标准解读

作为有机热载体炉的传热介质,有机热载体的质量对锅炉的安全运行至关重要。GB/T 24747-2023《有机热载体安全技术条件》于2023年5月23日发布和实施。该国家标准对有机热载体的应用、质量监测和问题处置等多方面进行了详细规定,对确保有机热载体炉的安全运行,防止事故发生和人员伤亡,促进能源高效利用和环境保护具有重大意义。文章对该国家标准进行了解读,以供读者参考。

WHR （Waste Heat Technology） Method in Tri-generation Model

This paper is focused on description of cool production in using WHR （Waste Heat Technology） Technology-a new method of centralized production of heat by using the waste heat from generated exhaust gas, which has been in 2009 developed and operated by companies HELORO s.r.o, and COMTHERM s.r.o.

Analytical solution for the time-fractional heat conduction equation in spherical coordinate system by the method of variable separation

In this paper,using the fractional Fourier law,we obtain the fractional heat conduction equation with a time-fractional derivative in the spherical coordinate system.The method of variable separation is used to solve the timefractional heat conduction equation.The Caputo fractional derivative of the order 0 〈 α≤ 1 is used.The solution is presented in terms of the Mittag-Leffler functions.Numerical results are illustrated graphically for various values of fractional derivative.

Polymorphism of heat shock protein 70-2 and enterocutaneous fistula in Chinese population

AIM: To investigate whether the heat shock protein 70-2 (HSP70-2) polymorphism is associated with enterocutaneous fistulas in a Chinese population.

Power Generation Systems Using Continuous Blowdown Waste Heat from Drum Boilers Driving an Organic Rankine Cycle

提出了一种利用汽包锅炉排污系统余热的有机朗肯循环发电系统,有机工质回收扩容器疏水的热量,并通过气轮机发电。建立了系统的热力性能分析模型,并对R227ea、RC318、R236ea、R245fa、R245ca、R123和R113等7种工质的热力性能进行了优化。结果表明,临界温度高的工质,其o2循环的最佳主气温度（蒸发温度）反而低；亚临界循环采用干流体时,过热不利于余热的利用；超临界循环可以改善热源与工质间的温度匹配,有利于增大系统输出功,但是其运行压力高、大比热区的传热恶化等问题是实际运行和设计需要考虑的因素；R236ea的热力性能优于其余6种工质。

Equation of Radiation Heat Transfer in Multiple Combustion Boiler Furnace of Fluidized Bed and Pulverized Coal Firing

The equation for radiation heat transfer in a multiple combustion boiler furnace with nuidized bed and pulverized coal firing is derived from direct calculation of radiation heat transfer.

The Application of Radiation Shields for Thermal Control of Superheater Tubes in Boiler

Superheater tubes temperature control is a necessity for long lifetime, high efficiency and high load following capability in boiler. This study reports a new approach for the control strategy design of boilers with special shields. The presented control strategy is developed based on radiation thermal shields with low emissivity coefficient and high reflectivity or scattering coefficient. In order to simulate the combustion event in boiler and heat transfer to superheater tubes, an effective set of computational fluid dynamic (CFD) codes is used. Results indicate a successful identification of over- heated zones on platen superheater tubes and effect of radiation shields for solving this problem.

计及碳交易的热电联产-储热-电锅炉风电消纳策略

为解决传统热电联产机组的热电耦合特性以及冬季采暖期间弃风消纳问题,提出了计及碳交易含储热热电联产机组和电锅炉联合运行的弃风消纳策略。首先将储热设备、电锅炉与热电联产机组联合运行来满足系统所需热负荷,从而提高热电联产机组电调峰能力。其次,为进一步控制碳排放量,引入阶梯式碳交易与优化电锅炉运行模式,兼顾系统运行成本、弃风消纳量以及碳排放量,构建计及碳交易的热电联产-储热-电锅炉风电消纳模型并进行求解。最后,以IEEE-30节点为例进行算例分析,结果表明所提策略能够有效促进风电消纳、减少碳排放量且有效降低系统运行成本。

燃气-蒸汽联合循环发电余热锅炉烟道均流装置数值模拟与优化

燃气-蒸汽联合循环发电中燃气轮机与余热锅炉主体经常采用大扩张角过渡段连接,导致下游烟气流动不均匀,影响余热锅炉NOx选择性催化还原烟气脱硝效率。对此,提出通过布置三级导流板来改善烟道内烟气的流动均匀性,并采用计算流体力学模拟方法研究过渡段导流板布置形式、安装角度及布置密度等参数对烟道内烟气流动特性的影响规律。结果表明:未设置导流装置时过渡段出现明显漩涡,涡度可达20 m-1,导致烟气流动均匀性差;过渡段安装一级变倾角导流板可显著抑制漩涡的尺寸,安装二级变倾角导流板可显著改善过渡段内烟气流动均匀性,但是烟道后端烟气速度均匀性仍不高,安装三级导流板可同步改善过渡段和烟道内烟气流动均匀性,在换热模块三之后相对速度标准差系数降至2.1%。优化的导流板布置为:一级导流板水平投影长度2.25 m,间距1.20 m,角度15°~30°等差递增;二级导流板水平投影长度1.36 m,间距1.40 m,角度15°~60°等差递增;三级导流板长度0.70 m,间距1.00 m,水平安装。研究结果可为烟气均流装置的设计提供理论指导。

吸收-压缩热泵回收高水分杂醇烟气余热研究

为了处理煤化工过程中产生的有害副产杂醇并回收热能,本文设计了一台以杂醇为燃料的热水锅炉,并在锅炉尾部加装了一种新型吸收-压缩复合热泵来回收烟气余热,通过Aspen Plus软件对热泵回收烟气余热流程进行模拟。结果表明杂醇烟气蕴含丰富潜热,采用该新型热泵能实现余热有效回收,额定工况下能使锅炉热效率提高11.01%。进一步研究了压缩机压比、回水温度和锅炉负荷对热泵性能的影响,并提出分别基于节能和碳减排效果的热泵性能系数COP_(a)和COP_(e)来全面分析热泵的运行性能。结果发现在压比为9.6时热泵COP_(a)和COP_(e)最高,且在压比小于9.6时,热泵性能会受回水温度升高的影响较大。随着锅炉负荷的增大,热泵系统的COP_(a)和COP_(e)先增大后减小。本文研究可为高水分烟气余热的深度回收和新型复合热泵的应用提供一些理论依据。

A Study on Modifying the Calculation Model of Valid Opening Size of Heat-bonded Nonwoven Fabrics

It has been found that there are marked errors in the value of valid opening size of heat-bonded nonwoven fabrics between theoretical calculations and engineering measurements. A new modified theoretical model is advanced in this paper. The equivalent diameter of the pore of a fibre web is used to calculate the valid opening size instead of the maximum diameter of inscribed circle used, because the fibres in practical fibre webs are flexible elastomers with definite diameters and the pore of fibre web may produce deformation in screening teat and engineering usage. The results show that the theoretical calculations coincide well with the engineering measurements. This method offers a theoretical basis for computer simulation to the performance of filters of heatbonded nonwoven fabrics.

Heat Capacities and Thermodynamic Properties of 3-(2,2-Dichloroethenyl)-2,2-dimethylcyclopropanecarboxylic Acid

The heat capacities of 3-（ 2,2-dichloroethenyl）-2,2-dimethylcyclopropanecarboxylic acid （a racemic mixture, molar ratio of cis-/trans-structure is 35/65） in a temperature range from 78 to 389 K were measured with a precise automatic adiabatic calorimeter. The sample was prepared with a purity of 98.75% （ molar fraction）. A solid-liquid fusion phase transition was observed in the experimental temperature range. The melting point, Tm, enthalpy and en- tropy of fusion, △fusHm, △fusSm, of the acid were determined to be （331.48±0.03 ） K, （16.321±0.031） kJ/mol, and （49.24±0.19） J/（ K·mol）, respectively. The thermodynamic functions of the sample, Ht-H298.15, Sr-S298.15 and Gr-G298.15, were reported at a temperature intervals of 5 K. The thermal decomposition of the sample was studied using thermogravimetric（TG） analytic technique, the thermal decomposition starts at ca. 418 K and ends at ca. 544 K, the maximum decomposition rate was obtained at 510 K. The order of reaction, preexponential factor and activation energy are n =0.23, A =7.3 ×10^7 min^-1 , E =70.64 kJ/mol, respectively.

Study on the Factors to Influence Dynamic Heat - moisture Comfort of Summer Clothing Fabrics

In this paper, the factors to influence the dynamic heat - moisture comfort of summer clothing fabrics have been studied. It is pointed out that, when the wind speed outside is high, or the air permeability is very good, the sweat of human body will evaporate mainly through turbulent diffusion. Because of the rapid sweat evaporation, human body will feel cold, and then, the difference in temperature and humidity of the micro - climatic section will be very slight. On the contrary, when the wind speed outside is slow or the air permeability is unsatisfactory, the sweat of human body will evaporate mainly through molecular diffusion, and in this case, the humidity of the micro - climatic section will be depended on the hygroscopicity of the fabric, that’ s to say, the better the hygroscopicity, the lower the humidity. It is difficult for pure wool fabric to loss heat because of its giving out much heat during the course of moisture - absorption in the initial stages of sweating. For pure polyester fabric,

A Compact Difference Scheme for Multi-point Boundary Value Problems of Heat Equations

In this paper,a compact difference scheme is established for the heat equations with multi-point boundary value conditions.The truncation error of the difference scheme is O(τ2+h^4),where t and h are the temporal step size and the spatial step size.A prior estimate of the difference solution in a weighted norm is obtained.The unique solvability,stability and convergence of the difference scheme are proved by the energy method.The theoretical statements for the solution of the difference scheme are supported by numerical examples.

Effect of Heat Treatment on Mechanical Properties and Microstructure of NST 37-2 Steel

Engineering materials, mostly steel, are heat treated under controlled sequence of heating and cooling to alter their physical and mechanical properties to meet desired engineering applications. In this study, the effect of heat treatment (annealing, normalising, hardening, and tempering) on the microstructure and some selected mechanical properties of NST 37-2 steel were studied. Sample of steel was purchased from local market and the spectrometry analysis was carried out. The steel samples were heat treated in an electric furnace at different temperature levels and holding times;and then cooled in different media. The mechanical properties (tensile yield strength, ultimate tensile strength, Young’s modulus, percentage reduction, percentage elongation, toughness and hardness) of the treated and untreated samples were determined using standard methods and the microstructure of the samples was examined using metallographic microscope equipped with camera. Results showed that the mechanical properties of NST 37-2 steel can be changed and improved by various heat treatments for a particular application. It was also found that the annealed samples with mainly ferrite structure gave the lowest tensile strength and hardness value and highest ductility and toughness value while hardened sample which comprise martensite gave the highest tensile strength and hardness value and lowest ductility and toughness value.