Investigations on High-Speed Flash Boiling Atomization of Fuel Based on Numerical Simulations

Flash boiling atomization(FBA)is a promising approach for enhancing spray atomization,which can generate a fine and more evenly distributed spray by increasing the fuel injection temperature or reducing the ambient pressure.However,when the outlet speed of the nozzle exceeds 400 m/s,investigating high-speed flash boiling atomization(HFBA)becomes quite challenging.This difficulty arises fromthe involvement ofmany complex physical processes and the requirement for a very fine mesh in numerical simulations.In this study,an HFBA model for gasoline direct injection(GDI)is established.This model incorporates primary and secondary atomization,as well as vaporization and boilingmodels,to describe the development process of the flash boiling spray.Compared to lowspeed FBA,these physical processes significantly impact HFBA.In this model,the Eulerian description is utilized for modeling the gas,and the Lagrangian description is applied to model the droplets,which effectively captures the movement of the droplets and avoids excessive mesh in the Eulerian coordinates.Under various conditions,numerical solutions of the Sauter mean diameter(SMD)for GDI show good agreement with experimental data,validating the proposed model’s performance.Simulations based on this HFBA model investigate the influences of fuel injection temperature and ambient pressure on the atomization process.Numerical analyses of the velocity field,temperature field,vapor mass fraction distribution,particle size distribution,and spray penetration length under different superheat degrees reveal that high injection temperature or low ambient pressure significantly affects the formation of small and dispersed droplet distribution.This effect is conducive to the refinement of spray particles and enhances atomization.

Effect of Gd on neutron absorption properties and electrochemical corrosion behavior of Zr-Gd alloy in boiling concentrated HNO3

A Zr-Gd alloy with neutron poisoning properties and resistance to boiling concentrated HNO3 corrosion was developed based on a corrosion-resistant Zr-702 alloy to meet the demand for neutron shielding in the closed-loop treatment of spent fuel and the nuclear chemical industry.In this study,1 wt.%,3 wt.%,5 wt.%,7 wt.%,and 9 wt.%Zr-Gd alloys were designed and fabricated with Zr-702 as the control element.The electrochemical behavior of the Zr-Gd alloys in boiling concentrated HNO3 was investigated,and the neutron shielding effect on plate thickness and Gd content was simulated.The experimental results demonstrate that the corrosion resistance of the alloy decreased slightly before~7-9 wt.%with increasing Gd content;this is the inflection point of its corrosion resistance.The alloy uniformly dissolved the Gd content that could not be dissolved in the Zr lattice,resulting in numerous micropores on the passivation coating,which deteriorated and accelerated the corrosion rate.The MCNP simulation demonstrated that when the Gd content was increased to 5 wt.%,a 2-mm-thick plate can shield 99.9%neutrons;an alloy with a Gd content≥7 wt.%required only a 1-mm-thick plate,thereby showing that the addition of Gd provides an excellent neutron poisoning effect.Thus,the corrosion resistance and neutron shielding performance of the Zr-Gd alloy can meet the harsh service requirements of the nuclear industry.

Simulation of single bubble dynamic process in pool boiling process under microgravity based on phase field method

We use the phase field method to track the gas-liquid interface based on the gas-liquid two-phase flow in the pool boiling process,and study the bubble nucleation,growth,deformation,departure and other dynamic behaviors on the heating surface under microgravity.By simulating the correlation between liquid undercooling and bubble dynamics,we find that the bubble growth time increases with the increase of liquid undercooling,but the effect of liquid undercooling on bubble height is not significant.Meanwhile,the gas-liquid-solid three-phase contact angle and the gravity level will also have an effect on the bubble growth time and bubble height.With the increase of the contact angle,the bubble growth time and bubble height when the bubble departs also increase.While the effect of gravity level is on the contrary,the smaller the gravity level is,the larger the bubble height and bubble growth time when the bubble separates.

Experimental and Numerical Analysis of the Influence ofMicrochannel Size and Structure on Boiling Heat Transfer

Computational fluid dynamics was used and a numerical simulation analysis of boiling heat transfer in microchannels with three depths and three cross-sectional profiles was conducted.The heat transfer coefficient and bubble generation process of three microchannel structures with a width of 80μm and a depth of 40,60,and 80μm were compared during the boiling process,and the factors influencing bubble generation were studied.A visual test bench was built,and test substrates of different sizes were prepared using a micro-nano laser.During the test,the behavior characteristics of the bubbles on the boiling surface and the temperature change of the heated wall were collected with a high-speed camera and a temperature sensor.It was found that the microchannel with a depth of 80μm had the largest heat transfer coefficient and shortest bubble growth period,the rectangular channel had a larger peak heat transfer coefficient and a lower frequency of bubble occurrence,while the V-shaped channel had the shortest growth period,i.e.,the highest frequency of bubble occurrence,but its heat transfer coefficient was smaller than that of the rectangular channel.

Lattice Boltzmann simulation of the effects of cavity structures and heater thermal conductivity on nucleate boiling heat transfer

The boiling heat transfer technology with cavity surfaces can provide higher heat flux under lower wall superheat,which is of great significance for the cooling of electronic chips and microelectromechanical devices.In this paper,the boiling characteristics of the cavity surfaces are investigated based on the lattice Boltzmann(LB)method,focusing on the effects of cavity shapes,sizes,and heater thermal conductivity on the heat transfer performance.The results show that the triangular cavity has the best boiling performance since it has less residual vapor and higher bubble departure frequency than those of the trapezoidal and rectangular cavities.As the cavity size increases,the enhancement of heat transfer by the cavity mouth is suppressed by the heat accumulation effect at the heater bottom.The liquid rewetting process during bubble departure is the reason for the fluctuation of the space-averaged heat flux,and the heater thermal conductivity determines the fluctuation amplitude.The evaporation of liquid in the cavity with high thermal conductivity walls is more intense,resulting in shorter waiting time and higher bubble departure frequency.

Comparisons of Structured Surface Floors for Pool Boiling Enhancement at Low Heat Fluxes: Hands-On Learning Setup for Heat Transfer Classroom

Various enhanced surfaces have been proposed over the years to improve boiling heat transfer. This paper introduces an experimental setup designed for boiling demonstration in the graduate-level Heat Transfer course. The pool boiling performance of water under atmospheric pressure of 1.025 bar is investigated by using several structured surfaces at heat fluxes of 28 and 35 kW/m2. Surfaces with holes, rectangular grooves, and mushroom fins are manufactured by an NC-controlled vertical milling machine. The heat flux versus excess temperature graph is plotted by using thermocouple measurements of water and base temperatures of the boiling vessel. The separation, rise, and growth of individual vapor bubbles from the surface during boiling were recorded with a digital camera. The results for the plain surface are compared to the Rohsenow correlation. The enhancement of heat transfer coefficient (h) ranged between 15% - 44.5% for all structured surfaces. The highest heat transfer coefficient enhancement is observed between 41% - 56.5% for holed surface-3 (405 holes) compared to the plain surface. The excess temperature dropped around 29% - 34% for holed surface-3 (405 holes) compared to the plain surface. The heat transfer coefficient increases as the spacing between channels or holes decreases. While the bubbles on holed and mushroomed surfaces were spherical, the bubbles on the flat and grooved surfaces were observed as formless. The suggested economical test design could be appropriate to keep students focused and participating in the classroom.

The‘New Normal’of Extreme Weather And the Urgency of Transformation“The era of global warming is over and the era of global boiling has arrived.”

Phong,a 42-year-old Vietnamese motorcyclist begins his busy day at 5 a.m.In Hanoi,light motorcycles are an important mode of transportation.Countless motorcycles shuttle through the streets and alleys of the city,transporting parcels,goods,and passengers to various destinations.Phong usually works for 12 hours straight with little rest.However,the unprecedented heat waves this summer had often pushed daytime temperatures to above 40 degrees Celsius,making it extremely difficult for Phong to complete his daily routine.Phong prepared a hat,a wet handkerchief,and more drinking water.He even installed a small umbrella above his mobile phone rack to prevent the phone from overheating in the sun because it is his only source of work.Despite all the equipment,he is still worried.“If I suffer heat stroke or anything else,I will be unable to work,”he said.“I can’t afford it.”

Stability of the Liquid-Vapor Interface under the Combined Influence of Normal Vibrations and an Electric Field

The regime of horizontal subcooled film boiling is characterized by the formation of a thin layer of vapor coveringthe surface of a flat horizontal heater. Based on the equations of motion of a viscous incompressible fluid and theequation of heat transfer, the stability of such a vapor film is investigated. The influence of the modulation of thegravity field caused by vertical vibrations of the heater of finite frequency, as well as a constant electric fieldapplied normal to the surface of the heater, is taken into account. It is shown that in the case of a thick vaporfilm, the phase transition has a little effect on the thresholds for the occurrence of parametric instability in thesystem and its transformation into the most dangerous one. At the same time, the electric field contributes toan increase in these thresholds. It was found that the effect of vibrations on the stabilization of non-parametricinstability in the system is possible only in a narrow region of the parameter space where long-wave damped disturbances exist and consists of reducing the critical heat flux of stabilization. A vapor film stabilized in this waycan be destroyed due to the development of parametric instability. In contrast to the case of a thick vapor layer,the threshold for the onset of parametric instability for thin films largely depends on the value of subcooling in thesystem. In addition, this threshold decreases with increasing electric field strength. For a vapor film ten micronsthick, the instability threshold can be reduced by a factor of three or more by applying an electric field of aboutthree million volts per meter.

Geology and mineralization of the Dongping supergiant alkalic-hosted Au-Te deposit(>100 t Au)in Northern Hebei Province,China:A review

The Dongping deposit is the largest alkalic-hosted gold deposit in China containing>100 t of Au.This paper presents a new understanding for Dongping ore system,based on the previous studies.The mineralization originally occurred at 400-380 Ma,simultaneous with emplacement of the Shuiquangou alkaline complex,and was overprinted by the hydrothermal activity in the Yanshanian.Isotope compositions of ores indicate metals of the deposit are mainly provided by the Shuiquangou complex.Ore-forming fluids are characterized by increasing oxygen fugacity and decreasing sulfur fugacity,while tellurium fugacity increased in the Stage II-2 and decreased in Stage II-3.These systematic changes are closely related to the processes of mineral precipitation and fluid evolution.Sulfide precipitation from Stage Ⅰ to Stage Ⅱ was triggered by fluid boiling,which leads to the precipitation of Pb-Bi-Te,due to decrement of sulfur fugacity.Condensation of gas phase containing high concentration of H_2Te leads to precipitation of Te-Au-Ag minerals and native tellurium.Based on these hypotheses,this paper present a polyphase metallogenic model as follow.During the Devonian,fluids were released from alkaline magmas,which carried ore-forming materials form the surrounding rocks and precipitate the early ores.During the Jurassic-Cretaceous,fluorine-rich fluids exsolved from highly factionated Shangshuiquan granite,which extracted and concentrated Au from the Shuiquangou complex and the Sanggan Group metamorphic rocks,and finally formed the Dongping gold deposit.

A new heat transfer correlation for flow boiling in helically coiled tubes

Based on the superposition principle of the nucleate boiling and convective heat transfer terms,a new correlation is developed for flow boiling heat transfer characteristics in helically coiled tubes.The effects of the geometric and system parameters on heat transfer characteristics in helically coiled tubes are investigated by collecting large amounts of experimental data and analyzing the heat transfer mechanisms. The existing correlations are divided into two categories,and they are calculated with the experimental data.The Dn factor is introduced to take into account the effect of a complex geometrical structure on flow boiling heat transfer.A new correlation is developed for predicting the flow boiling heat transfer coefficients in the helically coiled tubes,which is validated by the experimental data of R134a flow boiling heat transfer in them;and the average relative error and root mean square error of the new correlation are calculated.The results show that the new correlation agrees well with the experimental data,indicating that the new correlation can be used for predicting flow boiling heat transfer characteristics in the helically coiled tubes.

Preparation and characteristic analysis of rice husk high boiling solvent lignin

Rice husk high boiling solvent lignin （RHL） was prepared by high boiling solvent method, and its characteristics was analyzed by using chemical composition analysis, infrared spectroscopy, and ^1H-NMR and ^13C-NMR spectroscopy. The optimum prepared condition was that the rice husk with 70%-90% aqueous solution of 1, 4-butanediol was mixed with autoclave, under a certain weight ratio of solid raw material and solvent, heated to 200-220℃ for 1.0-3.0 h, then water-insoluble RHL was separated from the liquor reaction mixture by water precipitation. Results suggested that the lower digestion temperature and concentration of 1,4-butanediol were both unfavorable for extracting lignin. Chemical weight-average molecular weight of RHL was 1939 g·mol^-1, and the residual polysaccharide content was 5.12%. The ^1H-NMR spectra of RHL showed the relative intensity ratio, aliphatic over aromatic methoxyl groups, situated at 3.5-3.8 and 3.8-4.0 ppm, respectively. The results from ^13C-NMR spectra showed that β-O-4 bond and β-5 carbon-carbon linkage were the major linkages between RHL units. The C9-formula of RHL was calculated by the experiment data.

Changes of Petroleum Acid Distribution Characterized by FT-ICR MS in Heavy Acidic Crude Oil after True Boiling Point Distillation

The molecular transformations of carboxylic acids in heavy acidic SL crude before and after true boiling point distillation were examined by ultra-high resolution negative-ion electrospray ionization(ESI) Fourier transform ion cyclotron resonance mass spectrometry(FT-ICR MS). The acid class(heteroatom number), type(z numbers) and carbon number distributions were positively characterized. It was found out that the total acid number(TAN) of SL crude decreased after true boiling point distillation, and the abundance of O2 class in mass spectra was also found to be reduced from 67.6% to 34.5% in SL TBP mixed crude as measured by MS spectra, indicating to a potential carboxylic acid decomposition. However, it was interesting that the carboxylic acids type distribution in both oils was almost the same although their relative abundance in SL TBP mixed crude turned to be much lower, suggesting that various petroleum carboxylic acid types have the similar thermal decomposition reaction behavior. Furthermore, for each O2 type of acids in SL TBP mixed crude, the abundance of carboxylic acids with carbon number higher than 35 was reduced greatly, especially for those with carbon number higher than 60, the mass peaks of which were nearly totally removed, indicating that the large carboxylic acid molecules in heavy fractions decomposed more significantly because of longer heating time during the true boiling point distillation process. As a result, the reduction of TAN may be caused by the thermal decomposition of carboxylic acids especially those with high carbon number, suggesting that quick distillation or much lower pressure is required to avoid the thermal decomposition.

A New Experimental Rig of Testing Flow Boiling Heat Transfer of Refrigerantand Lubricant Mixture

This paper proposed a new experimental rig of testing flow boiling heat transfer of refrigerant and lubricant oil mixture. The quantity of oil in the test section can be controlled and regulated conveniently and accurately by connecting separate lubricant oil circuit with test section in parallel. It was built up by retrofitting a multiple air-conditioner and installing three oil-separators in serials at the compressor outlet. And so the lubricant oil in the discharged refrigerant gas of compressor can be removed completely.The refrigerant flow rate through test section can be bypassed by the by-path circuit of indoor unit.This experimental rig has advantages such as on-line and continuous oil injection, short time of obtaining stability, flexible operation, simple control, which lead to high efficiency in the research of flow boiling heat transfer of refrigerant and lubricant oil mixture.

Mechanism of Calcium Carbonate Scale Deposition under Subcooled Flow Boiling Conditions

Fouling of heat transfer surfaces during subcooled flow boiling is a frequent engineering problem in process industries. It has been generally observed that the deposits in such industrial systems consist mainly of calcium carbonate （CaCO3）, which has inverse solubility characteristics. This investigation focused on the mechanism to control deposition and the morphology of crystalline deposits. A series of experiments were carried out at different surface and bulk temperatures, fluid velocities and salt ion concentrations. It is shown that the deposition rate is controlled by different mechanism in the range of experimental parameters, depending on salt ion concentration. At higher ion concentration, the fouling rate increases linearly with surface temperature and the effect of flow velocity on deposition rate is quite strong, suggesting that mass diffusion controls the fouling process. On the contrary, at lower ion concentration, the fouling rate increases exponentially with surface temperature and is independent of the velocity, illustrating that surface reaction controls the fouling process. By analysis of the morphology of scale, two types of crystal （calcite and aragonite） are formed. The lower the temperature and ion concentration, the longer the induction period and the higher the percentage of calcite nreciDitated.

Support vector regression modeling in recursive just-in-time learning framework for adaptive soft sensing of naphtha boiling point in crude distillation unit

Prediction of primary quality variables in real time with adaptation capability for varying process conditions is a critical task in process industries.This article focuses on the development of non-linear adaptive soft sensors for prediction of naphtha initial boiling point(IBP)and end boiling point(EBP)in crude distillation unit.In this work,adaptive inferential sensors with linear and non-linear local models are reported based on recursive just in time learning(JITL)approach.The different types of local models designed are locally weighted regression(LWR),multiple linear regression(MLR),partial least squares regression(PLS)and support vector regression(SVR).In addition to model development,the effect of relevant dataset size on model prediction accuracy and model computation time is also investigated.Results show that the JITL model based on support vector regression with iterative single data algorithm optimization(ISDA)local model(JITL-SVR:ISDA)yielded best prediction accuracy in reasonable computation time.

Enhancement of Flow Boiling Heat Transfer with Surfactant

The surfactant additive octadecylamine (ODA) was used to enhance the flow boiling heat transfer of water in vertical copper tube, and the effects of the aqueous solution properties, mass fraction of ODA, mass flux and heat flux etc. on flow boiling heat transfer were investigated. In order to analyze the mechanism of enhancement on boiling heat transfer with ODA, the copper surface was detected by XPS, and the diagram of binding energy was obtained. The results show that ODA can be adsorbed on the surface of the copper wall, and affects the properties of the heating surfaces and enhances the flow boiling heat transfer of water. Only in low heat flux and in a suitable range of concentration, can ODA aqueous solution enhance flow boiling heat transfer, and the suitable mass fraction of ODA is in the range of 1×10 -5 5×10 -5 . In addition, compared with water, ODA aqueous solution does not increase the flow drag under the same experimental conditions.

Experimental investigation on boiling heat transfer and pressure drop of R245fa in a horizontal micro-fin tube

An experimental investigation on the boiling heat transfer and frictional pressure drop of R245fa in a 7 mm horizontal micro-fin tube was performed.The results show that in terms of flow boiling heat transfer characteristics,boiling heat transfer coefficient(HTC)increases with mass velocity of R245fa,while it decreases with the increment of saturation temperature and heat flux.With the increase of vapor quality,HTC has a maximum and the corresponding vapor quality is about 0.4,which varies with the operating conditions.When vapor quality is larger than the transition point,HTC can be promoted more remarkably at higher mass velocity or lower saturation temperature.Among the four selected correlations,KANDLIKAR correlation matches with 91.6%of experimental data within the deviation range of±25%,and the absolute mean deviation is 11.2%.Also,in terms of frictional pressure drop characteristics of flow boiling,the results of this study show that frictional pressure drop increases with mass velocity and heat flux of R245fa,while it decreases with the increment of saturation temperature.MULLER-STEINHAGEN-HECK correlation shows the best prediction accuracy for frictional pressure drop among the four widely used correlations.It covers 84.1%of experimental data within the deviation range of±20%,and the absolute mean deviation is 10.1%.

Heat Transfer in Nucleate Pool Boiling of Binary and Ternary Refrigerant Mixtures

Heat transfer coefficients in nucleate pool boiling were measured on a horizontal copper surface for refrigerants, HFC-134a, HFC-32, and HFC-125, their binary and ternary mixtures under saturated conditions at 0.9MPa. Compared to pure components, both binary and ternary mixtures showed lower heat transfer coefficients.This deterioration was more pronounced as heat flux was increased. Experimental data were compared with some empirical and semi-empirical correlations available in literature. For binary mixture, the accuracy of the correlations varied considerably with mixtures and the heat flux. Experimental data for HFC-32/134a/125 were also compared with available correlated equation obtained by Thome. For ternary mixture, the boiling range of binary mixture composed by the pure fluids with the lowest and the medium boiling points, and their concentration difference had important effects on boiling heat transfer coefficients.

Optimization of three-dimensional boiling enhancement structure at evaporation surface for high power light emitting diode

A theoretical model of phase change heat sink was established in terms of thermal resistance network. The influence of different parameters on the thermal resistance was analyzed and the crucial impact factors were determined. Subsequently, the forming methods including ploughing-extrusion and stamping method of boiling enhancement structure at evaporation surface were investigated, upon which three-dimensional microgroove structure was fabricated to improve the efficiency of evaporation. Moreover, the crucial parameters related to the fabrication of miniaturized phase change heat sink were optimized. The heat transfer performance of the heat sink was tested. Results show that the developed phase change heat sink has excellent heat transfer performance and is suitable for high power LED applications.

Application of Molecular Distillation Process to Extend the True Boiling Point Curve of Petroleum Residues 400 ℃ ＋

True Boiling Point （TBP） distillation is one of the most common experimental techniques for determination of petroleum properties. The methods for performing TBP distillation experiments are described by ASTM D2892 and by ASTM D5236. However, these methods are established for petroleum fractions that reach temperatures up to 565 ~C. In this work, two petroleum residues were distilled in a falling film molecular distillation prototype and the data were used to obtain the extension of the TBP curve above a temperature of 565 ~C. It was possible to extend the TBP curve of both petroleum up to temperatures close to 700 ~C with consistency and continuity in comparison to the standard curve. In addition, an amount of raw material that was been treated as residue could be reused.