Timing and Spouting Height of Sand Boils Caused by Liquefaction during the 2010 Mw 6.9 Yushu Earthquake, Tibetan Plateau, China

The 2010 Mw 6.9 Yushu earthquake produced a ~33-km-long co-seismic surface rupture zone along the pre-existing active Yushu Fault on China’s central Tibetan Plateau. Sand boils occurred along the tension cracks of the co-seismic surface rupture zone, and locally spouted up above the ground to coat the top of limestone blocks that had slid down from an adjacent ~300-m-high mountain slope. Based on our observations, the relations between the arrival times of P- and S-waves at the sand-boil location and the seismic rupture velocity, we conclude that 1) the sand boils occurred at least 18.24 s after the main shock;2) it took at least 4.09 - 9.79 s after the formation of co-seismic surface rupture to generate liquefaction at the sand-boil location;3) the spouting height of sand boils was at least 65 cm. Our findings help to clarify the relationships between the timing of lique-faction and the spouting height of sand boils during a large-magnitude earthquake.

Investigations on High-Speed Flash Boiling Atomization of Fuel Based on Numerical Simulations

Flash boiling atomization(FBA)is a promising approach for enhancing spray atomization,which can generate a fine and more evenly distributed spray by increasing the fuel injection temperature or reducing the ambient pressure.However,when the outlet speed of the nozzle exceeds 400 m/s,investigating high-speed flash boiling atomization(HFBA)becomes quite challenging.This difficulty arises fromthe involvement ofmany complex physical processes and the requirement for a very fine mesh in numerical simulations.In this study,an HFBA model for gasoline direct injection(GDI)is established.This model incorporates primary and secondary atomization,as well as vaporization and boilingmodels,to describe the development process of the flash boiling spray.Compared to lowspeed FBA,these physical processes significantly impact HFBA.In this model,the Eulerian description is utilized for modeling the gas,and the Lagrangian description is applied to model the droplets,which effectively captures the movement of the droplets and avoids excessive mesh in the Eulerian coordinates.Under various conditions,numerical solutions of the Sauter mean diameter(SMD)for GDI show good agreement with experimental data,validating the proposed model’s performance.Simulations based on this HFBA model investigate the influences of fuel injection temperature and ambient pressure on the atomization process.Numerical analyses of the velocity field,temperature field,vapor mass fraction distribution,particle size distribution,and spray penetration length under different superheat degrees reveal that high injection temperature or low ambient pressure significantly affects the formation of small and dispersed droplet distribution.This effect is conducive to the refinement of spray particles and enhances atomization.

Effect of Gd on neutron absorption properties and electrochemical corrosion behavior of Zr-Gd alloy in boiling concentrated HNO3

A Zr-Gd alloy with neutron poisoning properties and resistance to boiling concentrated HNO3 corrosion was developed based on a corrosion-resistant Zr-702 alloy to meet the demand for neutron shielding in the closed-loop treatment of spent fuel and the nuclear chemical industry.In this study,1 wt.%,3 wt.%,5 wt.%,7 wt.%,and 9 wt.%Zr-Gd alloys were designed and fabricated with Zr-702 as the control element.The electrochemical behavior of the Zr-Gd alloys in boiling concentrated HNO3 was investigated,and the neutron shielding effect on plate thickness and Gd content was simulated.The experimental results demonstrate that the corrosion resistance of the alloy decreased slightly before~7-9 wt.%with increasing Gd content;this is the inflection point of its corrosion resistance.The alloy uniformly dissolved the Gd content that could not be dissolved in the Zr lattice,resulting in numerous micropores on the passivation coating,which deteriorated and accelerated the corrosion rate.The MCNP simulation demonstrated that when the Gd content was increased to 5 wt.%,a 2-mm-thick plate can shield 99.9%neutrons;an alloy with a Gd content≥7 wt.%required only a 1-mm-thick plate,thereby showing that the addition of Gd provides an excellent neutron poisoning effect.Thus,the corrosion resistance and neutron shielding performance of the Zr-Gd alloy can meet the harsh service requirements of the nuclear industry.

Conceptual design and safety characteristics of a new multi-mission high flux research reactor

Research reactors with neutron fluxes higher than 10^(14) n cm^(−2) s^(−1) are widely used in nuclear fuel and material irradiation,neutron-based scientific research,and medical and industrial isotope production.Such high flux research reactors are not only important scientific research facilities for the development of nuclear energy but also represent the national comprehensive technical capability.China has several high flux research reactors that do not satisfy the requirements of nuclear energy development.A high flux research reactor has the following features:a compact core arrangement,high power density,plate-type fuel elements,a short refueling cycle,and high coolant velocity in the core.These characteristics make it difficult to simultaneously realize high neutron flux and optimal safety margin.A new multi-mission high flux research reactor was designed by the Institute of Nuclear and New Energy Technology at Tsinghua University in China;the reactor can simul-taneously realize an average neutron flux higher than 2.0×10^(15) n cm^(−2) s^(−1) and fulfill the current safety criterion.This high flux research reactor features advanced design concepts and has sufficient safety margins according to the preliminary safety analysis.Based on the analysis of the station blackout accident,loss of coolant accident,and reactivity accident of a single-control drum rotating out accidently,the maximum temperature of the cladding surface,minimum departure from nucleate boiling ratio,and temperature difference to the onset of nucleate boiling temperature satisfy the design limits.

Simulation of single bubble dynamic process in pool boiling process under microgravity based on phase field method

We use the phase field method to track the gas-liquid interface based on the gas-liquid two-phase flow in the pool boiling process,and study the bubble nucleation,growth,deformation,departure and other dynamic behaviors on the heating surface under microgravity.By simulating the correlation between liquid undercooling and bubble dynamics,we find that the bubble growth time increases with the increase of liquid undercooling,but the effect of liquid undercooling on bubble height is not significant.Meanwhile,the gas-liquid-solid three-phase contact angle and the gravity level will also have an effect on the bubble growth time and bubble height.With the increase of the contact angle,the bubble growth time and bubble height when the bubble departs also increase.While the effect of gravity level is on the contrary,the smaller the gravity level is,the larger the bubble height and bubble growth time when the bubble separates.

Experimental and Numerical Analysis of the Influence ofMicrochannel Size and Structure on Boiling Heat Transfer

Computational fluid dynamics was used and a numerical simulation analysis of boiling heat transfer in microchannels with three depths and three cross-sectional profiles was conducted.The heat transfer coefficient and bubble generation process of three microchannel structures with a width of 80μm and a depth of 40,60,and 80μm were compared during the boiling process,and the factors influencing bubble generation were studied.A visual test bench was built,and test substrates of different sizes were prepared using a micro-nano laser.During the test,the behavior characteristics of the bubbles on the boiling surface and the temperature change of the heated wall were collected with a high-speed camera and a temperature sensor.It was found that the microchannel with a depth of 80μm had the largest heat transfer coefficient and shortest bubble growth period,the rectangular channel had a larger peak heat transfer coefficient and a lower frequency of bubble occurrence,while the V-shaped channel had the shortest growth period,i.e.,the highest frequency of bubble occurrence,but its heat transfer coefficient was smaller than that of the rectangular channel.

Lattice Boltzmann simulation of the effects of cavity structures and heater thermal conductivity on nucleate boiling heat transfer

The boiling heat transfer technology with cavity surfaces can provide higher heat flux under lower wall superheat,which is of great significance for the cooling of electronic chips and microelectromechanical devices.In this paper,the boiling characteristics of the cavity surfaces are investigated based on the lattice Boltzmann(LB)method,focusing on the effects of cavity shapes,sizes,and heater thermal conductivity on the heat transfer performance.The results show that the triangular cavity has the best boiling performance since it has less residual vapor and higher bubble departure frequency than those of the trapezoidal and rectangular cavities.As the cavity size increases,the enhancement of heat transfer by the cavity mouth is suppressed by the heat accumulation effect at the heater bottom.The liquid rewetting process during bubble departure is the reason for the fluctuation of the space-averaged heat flux,and the heater thermal conductivity determines the fluctuation amplitude.The evaporation of liquid in the cavity with high thermal conductivity walls is more intense,resulting in shorter waiting time and higher bubble departure frequency.

Comparisons of Structured Surface Floors for Pool Boiling Enhancement at Low Heat Fluxes: Hands-On Learning Setup for Heat Transfer Classroom

Various enhanced surfaces have been proposed over the years to improve boiling heat transfer. This paper introduces an experimental setup designed for boiling demonstration in the graduate-level Heat Transfer course. The pool boiling performance of water under atmospheric pressure of 1.025 bar is investigated by using several structured surfaces at heat fluxes of 28 and 35 kW/m2. Surfaces with holes, rectangular grooves, and mushroom fins are manufactured by an NC-controlled vertical milling machine. The heat flux versus excess temperature graph is plotted by using thermocouple measurements of water and base temperatures of the boiling vessel. The separation, rise, and growth of individual vapor bubbles from the surface during boiling were recorded with a digital camera. The results for the plain surface are compared to the Rohsenow correlation. The enhancement of heat transfer coefficient (h) ranged between 15% - 44.5% for all structured surfaces. The highest heat transfer coefficient enhancement is observed between 41% - 56.5% for holed surface-3 (405 holes) compared to the plain surface. The excess temperature dropped around 29% - 34% for holed surface-3 (405 holes) compared to the plain surface. The heat transfer coefficient increases as the spacing between channels or holes decreases. While the bubbles on holed and mushroomed surfaces were spherical, the bubbles on the flat and grooved surfaces were observed as formless. The suggested economical test design could be appropriate to keep students focused and participating in the classroom.

The‘New Normal’of Extreme Weather And the Urgency of Transformation“The era of global warming is over and the era of global boiling has arrived.”

Phong,a 42-year-old Vietnamese motorcyclist begins his busy day at 5 a.m.In Hanoi,light motorcycles are an important mode of transportation.Countless motorcycles shuttle through the streets and alleys of the city,transporting parcels,goods,and passengers to various destinations.Phong usually works for 12 hours straight with little rest.However,the unprecedented heat waves this summer had often pushed daytime temperatures to above 40 degrees Celsius,making it extremely difficult for Phong to complete his daily routine.Phong prepared a hat,a wet handkerchief,and more drinking water.He even installed a small umbrella above his mobile phone rack to prevent the phone from overheating in the sun because it is his only source of work.Despite all the equipment,he is still worried.“If I suffer heat stroke or anything else,I will be unable to work,”he said.“I can’t afford it.”

Sand Liquefaction Phenomena During the Seismic Crisis of May 2012 in Emilia,Northern Italy

In May 2012,the Emilia region of the Po Valley was struck by a seismic crisis with two major events of magnitude M_w 6.1and M_w 5.9.The first event induced widespread sand blows formed along buried channels and old crevasse splay deposits.In the days immediately following the events,the detailed mapping and sampling of the erupted sand was fundamental to record all the seismically-induced phenomena.The study of a trench dug across large fractures at San Carlo(Ferrara)provided also valuable information on the sand blows mechanism and regome.The sedimentological and compositional characteristics of the fracture-filling materials indicate that the sands were erupted from a layer located between 6.8 and 7.5 m depth.Older and deeper Holocene and Pleistocene sand layers were not apparently involved in the liquefaction phenomena.

一种大批量快速提取白僵菌DNA的方法(英文)

[Objective] The aim was to optimize the mass and rapid method for DNA extraction of Beauvena bassiana. [Method] Boiling water DNA extraction method was improved, DNA extraction liquid was heated by PCR instrument and the extraction process was finished rapidly. [ Resuit] The quality of DNA obtained through mass and rapid extraction of fungal genomic DNA could meet the requirement of RAPD amplification analysis. The clear bands were amplified from 22 tested strains, the number of clear bands were different in the range of 2 -6 and the size of band were mainly concentrated in 450 -800 bp. The DNA extracted by this method also could completely meet the requirement of SCAR amplification. The amplified specific DNA bands used to mark the strain F263 were very clear. [Conclusion] This research provided relatively perfect method for mass and rapid extraction of fungal clenomic DNA.

四种补肾中草药中14种元素的测定及统计分析

本文采用因子分析法、方差分析法及相关分析法分析枸杞、黄精、巴戟天、肉苁蓉四种中药材中14种元素差异的显著性和相关性,为研究中药材微量元素与药效之间的关系提供一定的依据。方法:采用水煮法和微波直接消解法处理样品,以电感耦合等离子发射光谱法(ICP-AES)测定了枸杞、黄精、巴戟天、肉苁蓉中14种元素含量。采用因子分析法、方差分析法及相关分析法对测定结果作统计分析,分析不同补肾中药微量元素差异的显著性和相关性。实验结果表明,4种中药中K,Ca和Na的含量均较高,微波消解法提取的微量元素含量明显高于水煮法,此方法测定各元素的相对标准偏差(RSD)在0.15%~3.65%之间,加标回收率在94%~105.5%之间,表明本文测量结果可准确评估四种中药材中14种元素的含量。不同的提取方法对14种元素有显著影响,四种中药材元素具有相似性,含量差异明显。未来的研究中通过更多种类补肾中药中各种元素的分析,将有助于开拓不同元素在中药材中的功能新领域。

LNG船舶HEEL的应用和管理

HEEL(底脚货)的应用和管理是LNG船舶运输的一个极为重要的方面。HEEL担负着多项使命,它既是货舱冷却的冷剂,又是船舶燃料,又是货物。正确地认识、应用和管理HEEL,有助于LNG船舶安全、稳定和可靠的运输。

Preparation and Properties of HBS Lignin from Masson Pine

In order to establish a new method for making cellulose and lignin from Masson pine, a high boiling solvent(HBS) pulping process with an aqueous solvent of 1,4-butanediol was investigated. Masson pine chips were pulped with a 70%—90% aqueous solution of 1,4-butanediol containing a small amount of a catalyst at 200—220 ℃ for 60—180 min. HBS Masson pine cellulose is suitable for making paper. Water-insoluble HBS lignin was separated from the liquor reaction mixture by water precipitation. The recovered high boiling solvent(RHBS) is able to be recycled as a pulping solvent, indicating that the HBS method is a pulping process of Masson pine which is energy saving, resources saving and pollution free. HBS lignin has a better chemical reactivity and a lower ash content than lignin sulfonate.

Changes of Petroleum Acid Distribution Characterized by FT-ICR MS in Heavy Acidic Crude Oil after True Boiling Point Distillation

The molecular transformations of carboxylic acids in heavy acidic SL crude before and after true boiling point distillation were examined by ultra-high resolution negative-ion electrospray ionization(ESI) Fourier transform ion cyclotron resonance mass spectrometry(FT-ICR MS). The acid class(heteroatom number), type(z numbers) and carbon number distributions were positively characterized. It was found out that the total acid number(TAN) of SL crude decreased after true boiling point distillation, and the abundance of O2 class in mass spectra was also found to be reduced from 67.6% to 34.5% in SL TBP mixed crude as measured by MS spectra, indicating to a potential carboxylic acid decomposition. However, it was interesting that the carboxylic acids type distribution in both oils was almost the same although their relative abundance in SL TBP mixed crude turned to be much lower, suggesting that various petroleum carboxylic acid types have the similar thermal decomposition reaction behavior. Furthermore, for each O2 type of acids in SL TBP mixed crude, the abundance of carboxylic acids with carbon number higher than 35 was reduced greatly, especially for those with carbon number higher than 60, the mass peaks of which were nearly totally removed, indicating that the large carboxylic acid molecules in heavy fractions decomposed more significantly because of longer heating time during the true boiling point distillation process. As a result, the reduction of TAN may be caused by the thermal decomposition of carboxylic acids especially those with high carbon number, suggesting that quick distillation or much lower pressure is required to avoid the thermal decomposition.

Enhancement of Flow Boiling Heat Transfer with Surfactant

The surfactant additive octadecylamine (ODA) was used to enhance the flow boiling heat transfer of water in vertical copper tube, and the effects of the aqueous solution properties, mass fraction of ODA, mass flux and heat flux etc. on flow boiling heat transfer were investigated. In order to analyze the mechanism of enhancement on boiling heat transfer with ODA, the copper surface was detected by XPS, and the diagram of binding energy was obtained. The results show that ODA can be adsorbed on the surface of the copper wall, and affects the properties of the heating surfaces and enhances the flow boiling heat transfer of water. Only in low heat flux and in a suitable range of concentration, can ODA aqueous solution enhance flow boiling heat transfer, and the suitable mass fraction of ODA is in the range of 1×10 -5 5×10 -5 . In addition, compared with water, ODA aqueous solution does not increase the flow drag under the same experimental conditions.

Support vector regression modeling in recursive just-in-time learning framework for adaptive soft sensing of naphtha boiling point in crude distillation unit

Prediction of primary quality variables in real time with adaptation capability for varying process conditions is a critical task in process industries.This article focuses on the development of non-linear adaptive soft sensors for prediction of naphtha initial boiling point(IBP)and end boiling point(EBP)in crude distillation unit.In this work,adaptive inferential sensors with linear and non-linear local models are reported based on recursive just in time learning(JITL)approach.The different types of local models designed are locally weighted regression(LWR),multiple linear regression(MLR),partial least squares regression(PLS)and support vector regression(SVR).In addition to model development,the effect of relevant dataset size on model prediction accuracy and model computation time is also investigated.Results show that the JITL model based on support vector regression with iterative single data algorithm optimization(ISDA)local model(JITL-SVR:ISDA)yielded best prediction accuracy in reasonable computation time.

Facile preparation of core-shell Si@Li4Ti5O12 nanocomposite as large-capacity lithium-ion battery anode

As a promising alternative anode material,silicon(Si)presents a larger capacity than the commercial anode to achieve large capacity lithium-ion batteries.However,the application of pure Si as anode is hampered by limitations such as volume expansion,low conductivity and unstable solid electrolyte interphase.To break through these limitations,the core-shell Si@Li4Ti5O12nanocomposite,which was prepared via in-situ self-assembly reaction and decompressive boiling fast concentration method,was proposed in this work.This anode combines the advantages of nano-sized Si particle and pure Li4Ti5O12(LTO)coating layer,improving the performance of the lithium-ion batteries.The Si@Li4Ti5O12 anode displays a high initial discharge/charge specific capacity of 1756/1383 m Ahg^-1 at 500 mAg^-1(representing high initial coulombic efficiency of 78.8%),a large rate capability(specific capacity of 620 mAhg^-1 at4000 mAg^-1),an outstanding cycling stability(reversible specific capacity of 883 mAhg^-1 after 150 cycles)and a low volume expansion rate(only 3.3% after 150 cycles).Moreover,the synthesis process shows the merits of efficiency,simplicity,and economy,providing a reliable method to fabricate large capacity Si@Li4Ti5O12nanocomposite anode materials for practical lithium-ion batteries.

Experimental Study of the Distribution of Au and Cu in Aqueous Vapor Phase at High Temperatures and Its Role on Ore-forming Transportation

This study focuses on experiments of Au and Cu dissolved in vapor phase in hydrothermal fluids. Experiments prove that Au and Cu can re-distribute in vapor phase and liquid phase during separation of Au- and Cu-bearing supercritical fluids to vapor and liquid phases. These experimental results can illustrate some ore geneses, where boiling phenomena of ore fluids were found. Au- and Cubearing NaHCO3-HCl solutions were heated up to more than 350℃ in the main vessel, and then passed through a phase separator in a temperature range from 250℃ to 300℃, separated into vapor and liquid phases. We collected and analyzed the liquid and vapor samples separately, and found that Au and Cu dissolved and distributed in vapor phase. In some cases, the concentrations of Au and Cu in vapor are higher than those in liquid phase. Those experiments are used to interpret field observations of fluid inclusion data of some Au and Cu deposits, and demonstrate that some Au and Cu ore deposits are derived from metals transportation in vapor phase.

Vacuum press drying studies on two fast-growing Indian wood species

Two fast-growing Indian species, Melia composita Benth. and Eucalyptus tereticornis Sm., which have different sets of physical properties, were dried together in a vacuum press dryer(VPD) under two drying conditions,i.e., above boiling point(ABP) and below boiling point(BBP). The ABP and BBP conditions were maintained by keeping the temperature constant at 75 ℃ and maintaining two pressure levels: 300 mm of Hg(ABP) and 450 mm of Hg(BBP). In order to understand pressure conditions at the core during vacuum drying, a cylindrical brass pipe was inserted in both wood cores and attached with pressure gauges placed outside of the VPD. The results indicate that the Melia wood core attained equilibrium pressure immediately with the pressure of VPD, while Eucalyptus attained it very slowly, reaching equilibrium at later stages of drying when cracks and checks advanced to the core.The drying rate was higher for Melia than Eucalyptus under both drying conditions. The drying rate of Melia(ABP) was higher than Melia(BBP), however, the drying rate for Eucalyptus(ABP) was not significantly different from the BBP drying rate.