Evaluation of the cement bond quality through filtering the reflected ultrasonic waves

High cement bond quality is required to keep an oil well from hydraulic commu- nication between zones. In the cement bond evaluation, the ultrasonic echo method is widely used for its capability of channeling azimuth detection. Full waveforms reflected from the cased hole are simulated for different bonding conditions by the generalized transfer matrix method. Because of the high acoustic impedance of casing, the amplitudes of the reflected waves from the cement and the formation are small and cannot easily be used to evaluate the cementing condition. The wave that can propagate into the cement and the formation through the casing concentrates closely on the casing resonant frequency. To reduce the amplitude of the reflected wave from the casing inner surface and highlight the part of the reflected wave which carries the cementing quality information, the reflected full wave is filtered according to the casing resonant frequency. There are several wave packets in the filtered waveform. When the amplitude of the second wave packet is low, the cement bonds well with the casing, otherwise poorly. A low amplitude third wave packet is an indication of a good bond of the cement with the formation, otherwise poor. To reveal the sensitivity of the reflection wave amplitudes to the incident angle, reflected full waveform is modeled when an acoustic beam with finite width is incident on the casing. It is shown that the bond evaluation method based on filtered wave packets is valid for incident angle less than 5 degrees.

Experimental Investigation of Second Interface Cement Bond Evaluation

Cement bond model wells （1：10 scaled-down） were made with a gradually degrading cement annulus for cement bond evaluation of the first interface （between the casing and the cement annulus） and the second interface （between the cement annulus and the formation）. Experimental simulation on cement bond logging was carried out with these model wells. The correlation of acoustic waveforms, casing wave energy and flee casing area before and after cement bonding of the second interface was established. The experimental results showed that the arrival of the casing waves had no relationship with the cement bonding of the second interface, but the amplitude of the casing head wave decreased obviously after the second interface was bonded. So, cement bonding of the second interface had little effect on the evaluation of the cement bond quality of the first interface by using casing head wave arrivals. Strong cement annulus waves with early arrivals were observed before the second interface was bonded, while obvious ＂formation waves＂ instead of cement annulus waves were observed after the second interface was bonded.

Seepage Mitigation in Hydropower Dams by Optimization in Roller Compacted Concrete Interlayer (Monoliths) Joint Bonding Technology

Roller Compacted Concrete (RCC) has gained favorable recognition in hydropower and water resource dam construction. With optimization in construction technology and materials used for RCC Dams, cost is no longer a major disadvantage as compared to environmental impact, that is, wildlife habitat disruption. In as much as it has become optimal for investment in hydropower dam construction, the scourge for dam failure is still eminent, which is as a result of excessive seepage compromising the integrity of the mechanical properties of the dam. The aim of the paper is to highlight successful application methods in joint bonding to avoid excessive seepage and reduce the autogenous healing to a few years of operation. In view of optimization, this paper presents a comprehensive study on the influences of interlayer joints bonding quality from RCC mix performances and how it consolidates the RCC layers to withstand the shear strength along the interface, especially on the high dams. The case study is the RCC dam at the 750 MW Kafue Gorge Lower Hydropower Station. The scope of the study reviews the joint type judged by Modified Maturity Factor (MMF) with joint surface long time exposed in regions with dry and high temperature, technical measures of layer bonding quality control under condition of long time joint surface exposure, effects of joints shear strength and impermeability of the RCC layers when under the conditions of plastic and elasticity. The subtle observations made during the dam construction phases were with respect to the optimal use of materials in relation to RCC mix designs and the basis for equipment calibration for monitoring important data that can be referenced during analysis of shear forces acting on the RCC dam over time.

Preparation of phenol formaldehyde resin from phenolated wood

The technique for preparing phenol formaldehyde resin from phenolated wood (PWF) and its characters were studied and analyzed. Poplar (Populus spp.) wood meal was liquefied by phenol in the presence of sulfuric acid as a catalyst. After the liquefied products were cooled, alkaline catalyst and formaldehyde were added. The mixture was kept at (60?) C for 1h and then was heated to (85?) C for 1h. The influence of molar ratio of formaldehyde to phenol (F/P) was investigated. The results showed when the molar ratio of formaldehyde to phenol was over 1.8, the PWF adhesives had high bond quality, bond durability and extremely low aldehydes emissions.

Azimuthal cement evaluation with an acoustic phased-arc array transmitter:numerical simulations and field tests

We developed a novel cement evaluation logging tool,named the azimuthally acoustic bond tool（AABT）,which uses a phased-arc array transmitter with azimuthal detection capability.We combined numerical simulations and field tests to verify the AABT tool.The numerical simulation results showed that the radiation direction of the subarray corresponding to the maximum amplitude of the first arrival matches the azimuth of the channeling when it is behind the casing.With larger channeling size in the circumferential direction,the amplitude difference of the casing wave at different azimuths becomes more evident.The test results showed that the AABT can accurately locate the casing collars and evaluate the cement bond quality with azimuthal resolution at the casing-cement interface,and can visualize the size,depth,and azimuth of channeling.In the case of good casingcement bonding,the AABT can further evaluate the cement bond quality at the cementformation interface with azimuthal resolution by using the amplitude map and the velocity of the formation wave.

Effect of curing condition on bonding quality of scarf-repaired composite laminates

Both single-face vacuum bag curing(SVC) and double-face vacuum bag curing(DVC)can be used in scarf repair of composite structures. But different curing conditions caused by the sealing state may affect the bonding quality of scarf-repaired structures. In this paper, the effect of curing condition on bonding quality of scarf-repaired laminates was experimentally investigated in terms of surface profiles, moisture absorption curves and section profiles. In order to further explore the moisture absorption mechanism, finite element model of the repaired laminates using DVC was established with moisture diffusion of both the adhesive and composite laminates considered. This model was verified by experimental results. Based on the model of DVC case, the model of SVC case was built by changing moisture absorption parameters of the adhesive. Results show that SVC reduces the bonding quality, mainly reflecting in more adhesive inner voids and patch-toparent dislocation. And SVC increases moisture absorption rate and moisture equilibrium content of the adhesive, and its effect on the former is far greater than that on the latter.

An acoustic-wave theory for casing bond evaluation using viscoelastic slip boundary modeling

Slip boundary condition is commonly utilized to model elastic wave propagation through layered earth media. The same approach is used here to characterize acoustic wave propagation along a cased borehole with various cement bond conditions. By modeling the cement layer between casing and formation as a viscoelastic slip interface with complex coupling rigidity parameters, one can not only reduce the complexity in the classical elastic wave modeling of the problem, but also efficiently model various complicated wave phenomena that are difficult for the existing modeling. More specifically, the new theory can well describe the effect of the cement bond condition change and the location of the change(i.e., whether it is in the first interface between casing and cement, or the second interface between cement and formation) on the acoustic waves,demonstrating the good modeling capability and predicting power. Application of the theory to field data shows that the theory can correctly model the acoustic wave characteristics and interpret the cement bond condition, thus providing a useful fundament theory for casing bond evaluation using acoustic logging.

No-formaldehyde Wood-plastic Composite Plywood in China

As a new product invented by the Research Institute of Wood Industry, no-formaldehyde wood-plastic composite plywood is the harvest of the cross-study on wood-plastic composite and plywood industry, It has no formaldehyde emission, with an excellent environment-friendly performance and a good bonding quafity. This paper analyses the strongpoints and market of this wood-plastic composite plywood.