A Study on Hydroelastic Response of Box-Type Very Large Floating Structures

The application of very large floating structure (VLFS) to the utilization of ocean space and exploitation of ocean resources has become one of the issues of great interest in international ocean engineering field. Owing to the advantage of simplicity in structure and low cost of construction and maintenance, box-type VLFS can be used in the calm water area near the coast as the structure configuration of floating airport. In this paper, a 3D linear hydroelastic theory is used to study the dynamic response of box-type VLFS in sinusoidal regular waves. A beam model and a 3D FEM model are respectively employed to describe the dynamic characteristics of the box-type Structure in vacuum. A hydrodynamic model (3D potential theory of flexible body) is applied to investigate the effect of different dry models on the hydroelastic response of box-type structure. Based on the calculation of hydroelastic response in regular waves, the rigid body motion displacement, flexible deflection, and the short term and long term wave induced bending moments are also predicted.

Theoretical and Experimental Studies of a Box-Type Solar Cooker in Unfavorable Climatic Conditions

A box-type solar cooker with an inclined surface, equipped with a concentration reflector to allow maximum energy to be collected, enabled cooking tests to be carried out in the rainy season. Different thermocouples were implanted on various places of the cooker. The temperature measurements from these sensors were taken every 10 minutes. The tests presented in this article relate to the preparation of eggs and rice. The absorber temperatures during the tests exceeded 100°C. The cooking times were between 1 h 50 min and 2 h 20 min despite the numerous cloudy periods. The cooker made it possible to reach sufficient temperatures for healthy cooking of food. The results obtained for these first tests are satisfactory and very encouraging.

Experimental Study on Ammonia Co-Firing with Coal for Carbon Reduction in the Boiler of a 300-MW Coal-Fired Power Station

To reduce CO_(2) emissions from coal-fired power plants,the development of low-carbon or carbon-free fuel combustion technologies has become urgent.As a new zero-carbon fuel,ammonia(NH_(3))can be used to address the storage and transportation issues of hydrogen energy.Since it is not feasible to completely replace coal with ammonia in the short term,the development of ammonia-coal co-combustion technology at the current stage is a fast and feasible approach to reduce CO_(2) emissions from coal-fired power plants.This study focuses on modifying the boiler and installing two layers of eight pure-ammonia burners in a 300-MW coal-fired power plant to achieve ammonia-coal co-combustion at proportions ranging from 20%to 10%(by heat ratio)at loads of 180-to 300-MW,respectively.The results show that,during ammonia-coal co-combustion in a 300-MW coal-fired power plant,there was a more significant change in NO_(x) emissions at the furnace outlet compared with that under pure-coal combustion as the boiler oxygen levels varied.Moreover,ammonia burners located in the middle part of the main combustion zone exhibited a better high-temperature reduction performance than those located in the upper part of the main combustion zone.Under all ammonia co-combustion conditions,the NH_(3) concentration at the furnace outlet remained below 1 parts per million(ppm).Compared with that under pure-coal conditions,the thermal efficiency of the boiler slightly decreased(by 0.12%-0.38%)under different loads when ammonia co-combustion reached 15 t·h^(-1).Ammonia co-combustion in coal-fired power plants is a potentially feasible technology route for carbon reduction.

Simplified Applicable Model for Fire Tube Boiler

This research aims to present a simplified mathematical model to predict the performance of fire tube boilers, taking into account the necessity of knowing the components of exhaust gases and the extent of their compatibility with environmental laws and requirements. The model shown is for a horizontal, three-pass, wet-back fire tube boiler at steady-state, steady-flow operation. It is concluded from the applicability of the model for different boiler capacity ratings that the results are simplified and important for the boiler manufacturers to predict the performance and make the choice to modify the proposed design to achieve certain needs.

Numerical Simulation of Combustion in 660MW Tangentially Fired Pulverized Coal Boiler on Ultra-Low Load Operation

In this paper,the combustion conditions in the boiler furnace of a 660 MWtangential fired pulverized coal boiler are numerically simulated at 15%and 20%rated loads,to study the flexibility of coal-fired power units on ultra-low load operation.The numerical results show that the boiler can operate safely at 15%and 20%ultra-low loads,and the combustion condition in the furnace is better at 20%load,and the tangent circles formed by each characteristic section in the furnace are better,and when the boiler load is decreased to 15%,the tangent circles in the furnace begin to deteriorate.The average flue gas temperature of different areas of the furnace shows that when the boiler furnace operates under ultra-low load conditions,the average smoke temperature of the cold ash hopper at 20%load is basically the same as the average smoke temperature at 15%load;in the burner area,the average smoke temperature of the cold ash hopper at 20%load is about 50 K higher than that at 15%load;in the burned out area,the average smoke temperature of the cold ash hopper at 20%load is slightly higher than that at 15%load.The average temperature of flue gas in the furnace showed a tendency to increase rapidly with the height of the furnace,then slow down and fluctuate the temperature in the burner area,and finally increase slightly in the burnout area due to the further combustion of combustible components to release heat,and then began to decrease.

Optimizing Two-Phase Flow Heat Transfer:DCS Hybrid Modeling and Automation in Coal-Fired Power Plant Boilers

In response to escalating challenges in energy conservation and emission reduction,this study delves into the complexities of heat transfer in two-phase flows and adjustments to combustion processes within coal-fired boilers.Utilizing a fusion of hybrid modeling and automation technologies,we develop soft measurement models for key combustion parameters,such as the net calorific value of coal,flue gas oxygen content,and fly ash carbon content,within theDistributedControl System(DCS).Validated with performance test data,thesemodels exhibit controlled root mean square error(RMSE)and maximum absolute error(MAXE)values,both within the range of 0.203.Integrated into their respective automatic control systems,thesemodels optimize two-phase flow heat transfer,finetune combustion conditions,and mitigate incomplete combustion.Furthermore,this paper conducts an in-depth exploration of the generationmechanismof nitrogen oxides(NO_(x))and low oxygen emission reduction technology in coal-fired boilers,demonstrating a substantial reduction in furnace exit NO_(x) generation by 30%to 40%and the power supply coal consumption decreased by 1.62 g/(kW h).The research outcomes highlight the model’s rapid responsiveness,enabling prompt reflection of transient variations in various economic indicator parameters.This provides a more effective means for real-time monitoring of crucial variables in coal-fired boilers and facilitates timely combustion adjustments,underscoring notable achievements in boiler combustion.The research not only provides valuable and practical insights into the intricacies of two-phase flow heat transfer and heat exchange but also establishes a pioneering methodology for tackling industry challenges.

Numerical Calculations and Cold Tests for Flow Fields of a 220t/h Retrofitted Oil-Boiler

In this paper, cold simulation experiments and numerical calculations are conducted to predict 3 D flow field aerodynamics for an oil furnace after being retrofitted due to its fuel variation. K ε model and SIMPLE program under body fit coordination (BFC) system, in which TTM non orthogonal method is used to control the irregular geometric boundary, are adopted to solve the control equations. Model tests are conducted to check the calculation results, showing that they are in agreement with each other. Three different alternatives with different side window locations are also calculated to optimize the designs. The field retrofitting results show that the combination of cold tests with numerical calculations has prosperous application in retrofitting or renewing medium and small boilers.

Three-Dimensional Dynamic Modeling of a Tangentially Fired Utility Boiler Furnace

The tangentially fired utility boiler furnace is divided into several sections. The dynamic mathematical models for each section are presented. In the combustion zone, three dimensional model is used, while for the upper sections, lumped parameter model is used instead. With the combination of different models, we can get detailed distributions of gas velocity, temperature, chemical species, heat flux, etc. in the furnace, but with less CPU time. The radiation through the interfaces of each section is cons...

Modeling and Simulation Study on Reverse Swirl of Secondary Air in Large Tangentially Fired Boiler

Based on the porosity method and the improved non uniform QUICK scheme, this paper describes a three dimensional computer simulation to predict the flow characteristics in a tangentially fired boiler. The model is applied to a 600?MW boiler modeling under different operating conditions of reverse swirl of secondary air. The numerical results achieve reasonable agreement with experimental data. The calculated results of flow field, the pressure distribution, the relative diameter of tangential circle, angular momentum flux in furnace and the velocity distribution index in horizontal gas pass are analyzed in detail. And then the effects of the reverse swirl of secondary air on flue gas imbalance are discussed. Finally a reasonable operating condition of the reverse swirl of secondary air is presented.

Neural network approach to predicting mercury emission from utility boiler

The feasibility of using an ANN method to predict the mercury emission and speciation in the flue gas of a power station under un-tested combustion/operational conditions is evaluated. Based on existing field testing datasets for the emissions of three utility boilers, a 3-layer back-propagation network is applied to predict the mercury speciation at the stack. The whole prediction procedure includes： collection of data, structuring an artificial neural network （ANN） model, training process and error evaluation. A total of 59 parameters of coal and ash analyses and power plant operating conditions are treated as input variables, and the actual mercury emissions and their speciation data are used to supervise the training process and verify the performance of prediction modeling. The precision of model prediction （ root- mean-square error is 0. 8 μg/Nm3 for elemental mercury and 0. 9 μg/Nm3 for total mercury） is acceptable since the spikes of semi- mercury continuous emission monitor （SCEM） with wet conversion modules are taken into consideration.

Analysis of Prese nt Operating Situati on of Large Size Coal-F ired Utility Boilers

Large size utility boilers develop rapidly in China, both their reliability and economics have reached better level. The operating situations of various existing boilers on the basis of different coals are analyzed, it is held that, the notable energy imbalance of furnace exit, ever existing in the tangential firing boilers has been solved, with comparatively lower NOX emission concentration of gained. The higher NOX emission concentration and furnace slagging etc. problems existing in wall firing boilers are notable. The comprehensive analysis shows that, it is appropriate to choose lower furnace volume heat release rate and higher flame height in the type selection design of boilers, and sufficient margin should be kept in the selection of coal pulverizing mills.

超临界循环流化床锅炉深度调峰时水冷壁流动不稳定特性计算分析

针对深度调峰时超临界循环流化床锅炉水冷壁管道内的汽液两相流动不稳定问题,提出了一种适用于不同工况的频域法数学模型。通过对质量、能量、动量方程进行小扰动线性化后经拉普拉斯变换得到了用于描述管道内汽液流体流动稳定性的传递函数,通过图解奈奎斯特图的方法判断管内工质流动的稳定性。然后,通过该模型计算了某350 MW超临界循环流化床锅炉水冷壁管段的不稳定边界并研究了不同参数对流动不稳定特性的影响。计算结果表明:所选回路在20%和50%锅炉最大连续蒸发量负荷发生流动不稳定时,热负荷分别为76.09 kW·m^(-2)和113.52 kW·m^(-2),水冷壁管道流动稳定且安全;入口过冷度对临界热流密度的影响呈非单值性;增大质量流速使流体的进口和出口密度差减小,有利于流动的稳定;增大入口节流系数,可以抑制入口处流量的脉动,有利于流动的稳定;在不同的工况条件下,改变管段倾斜角度会对流动稳定性产生不同的影响。

Characteristics of Phosphorus Adsorption with Boiler Slag and Process Optimization

[Objective] This study aimed to investigate the characteristics of phosphorus adsorption on boiler slag and optimize the adsorption process. [Method] Boiler slag was used as an adsorbent in the single-grade adsorption process to dispose the rural domestic sewage. During the course, phosphorus adsorption kinetics and thermodynamics, adsorption operating curve and the minimum boiler slag dosage were analyzed and calculated. [Result] Langmuir adsorption isotherm could be applied to describe the absorption of phosphorus with boiler slag, and the absorption kinetics was confirmed with the pseudo second-order equation. The maximum absorption quantity and the initial absorption rate increased with the rise of temperature, reaching up to 0.159 1 mg/g and 0.169 8 mg/(g·min) respectively at 40 ℃. Thermodynamic variables ΔG0<0 and ΔH0>0 indicated that the entire process was a spontaneous endothermic reaction, and high temperature would facilitate the reaction of absorption. In the single grade adsorption, the minimum adsorbent dosage decreased as the temperature rose; at 40 ℃ the optimum mass ratio of boiler slag to wastewater was 3.31 kg/m3. [Conclusion] The adsorption process with boiler slag as adsorbent is an economical and effective approach for treating rural domestic sewage.

INTRODUCTION TO INCONEL ALLOY 740: AN ALLOY DESIGNED FOR SUPERHEATER TUBING IN COAL-FIRED ULTRA SUPERCRITICAL BOILERS

Chinese utilities as well as those worldwide are facing increased demand for additional electricity, reduced plant emissions and greater efficiency. To meet this challenge will require increasing boiler temperature, pressure and coal ash corrosion resistance of the materials of boiler construction of future coal-fired boilers. A new nickel-based tube alloy, INCONEL^R alloy 740, is described aiming at meeting this challenge. Emphasis will be on describing the alloy＇ s mechanical properties, coal-ash and steam corrosion resistance. Microstructural stability as a function of temperature and time is addressed as well as some of the early methodology em- ployed to arrive at the current chemical composition.

基于AI的火力发电厂锅炉优化控制系统设计

针对火力发电厂锅炉控制中存在的低效率、高排放等问题,设计了一套基于AI的优化控制系统。该系统集成数据采集、智能分析与动态优化控制模块,可实时感知锅炉工况,并自适应调整燃烧参数。经过与传统PID控制之间的对比实验,证实了该设计系统在提升锅炉热效率、降低污染物排放、减小参数波动等方面的显著优势,为火电行业的智能化升级提供了新思路。

Corrosion Behavior of TP316L of Superheater in Biomass Boiler with Simulated Atmosphere and Deposit

Corrosion behavior of TP316L was investigated with simulated atmosphere and ash deposition for the superheater in biomass boiler.Corrosion dynamic curves were plotted by mass gain.The results showed that the corrosion was dependent on temperature and was greatly accelerated by ash deposition.The mass gain was distinctly reduced in the presence of SO2 with and without ash deposition on the specimens.Corrosion rates with ash deposit at different temperatures were calculated.Two feasible methods were provided to avoid serious high-temperature corrosion in the biomass boiler.

基于模糊关联规则的火电厂锅炉设备故障智能预警研究

为降低火电厂锅炉设备故障而造成的经济与社会损失,提出了一种基于改进的K-Means算法(I-KE)和模糊C均值(FCM)算法的智能故障预警方法。通过优化初始聚类中心,减少信息熵,提高聚类的稳定性,并对聚类结果进行模糊化处理,建立模糊等级数据库,记录每个数据点对聚类中心的隶属度。结合模糊关联规则,通过计算模糊支持度和模糊置信度,挖掘关键参数之间的模糊关系,以提升预警模型的响应速度和准确度。在实例分析中,选择华电榆横发电有限责任公司的超临界参数锅炉,根据风量参数的聚类结果,验证了模糊化处理和模糊关联规则在实际应用中的有效性。结果表明,通过结合I-KE-FCM算法和模糊关联规则,可以有效提升火电厂锅炉设备故障预警的准确性和实时性,确保火电厂的安全运行。

Flexibility of a 300 MW Arch Firing Boiler Burning Low Quality Coals

Experimental investigations on the flexibility of a 300 MW Arch Firing (AF) coal-fired boiler when burning low quality coals is reported. Measurements of gas temperature and species concentration and char sampling using a water-cooled suction pyrometer were carried out along the furnace elevation. The carbon content and the size distribu-tions of the char samples were obtained. The char morphology was examined using a field emission scanning electron microscope (FESEM). The char sampling was performed on this type of boiler for the first time. The results indicate that the flexibility of this boiler burning low quality coals under a moderate boiler load is better than its flexibility under a high boiler load. Because of the insufficient capacity of the coal pulverizers used,in case of low coal quality the pul-verized coal fineness will drastically decrease under high boiler loads. This causes an increase in the loss due to incom-plete mechanical and chemical combustion. This is the main cause of a low burnout degree of the pulverized coal and the decrease of the flexibility of this AF boiler under a high boiler load.

60 MW循环流化床锅炉水冷壁泄漏原因分析

旨在分析某热电厂2号循环流化床锅炉水冷壁管泄漏的原因。通过宏观检查、金相检查及拉伸试验等方法,对泄漏管样及对比管样的焊接质量、组织状态及力学性能进行了全面检测。宏观检查发现,泄漏管样及一处对比管样堆焊处存在焊接裂纹及局部焊瘤,表明焊接时电流过大导致母材过热熔化;金相检查进一步证实了过烧组织的形成及焊接裂纹的扩展路径;拉伸试验结果表明,未泄漏管样的力学性能符合标准要求。泄漏原因为水冷壁管表面堆焊时焊接电流过大,导致母材过烧并产生焊接裂纹。

Feasibility Analysis on the Integrated Application of Solar Energy, Biogas, Coal-fired Boiler and Radiant Floor Heating for Rural Residence

The feasibility of adopting a balanced energy mix mode (domestic solar energy, biogas, coal-fired boiler and radiant floor heating) was proposed. Taking a typical rural residence in Zhengzhou City for example, the study through theoretical analysis and calculation showed that such a balanced energy mix is an economic way and efficient in saving energy and reducing air pollution, and elaborated the theoretical feasibility of popularizing such a heat supply mode in rural areas.