A Novel Braking Control Strategy for Hybrid Electric Buses Based on Vehicle Mass and Road Slope Estimation

Proper braking force distribution strategies can improve both stability and economy performance of hybrid electric vehicles,which is prominently proved by many studies.To achieve better dynamic stable performance and higher energy recovery efficiency,an effective braking control strategy for hybrid electric buses(HEB)based on vehicle mass and road slope estimation is proposed in this paper.Firstly,the road slope and the vehicle mass are estimated by a hybrid algorithm of extended Kalman filter(EKF)and recursive least square(RLS).Secondly,the total braking torque of HEB is calculated by the sliding mode controller(SMC),which uses the information of brake intensity,whole vehicle mass,and road slope.Finally,comprehensively considering driver’s braking intention and regulations of the Economic Commission for Europe(ECE),the optimal proportional relationship between regenerative braking and pneumatic braking is obtained.Furthermore,related simulations and experiments are carried out on the hardware-in-the-loop test bench.Results show that the proposed strategy can effectively improve the braking performance and increase the recovered energy through precise control of the braking torque.

Experimental prototyping of the adhesion braking control system design concept for a mechatronic bogie

The dynamic parameters of a roller rig vary as the adhesion level changes.The change in dynamics parameters needs to be analysed to estimate the adhesion level.One of these parameters is noise emanating from wheel–rail interaction.Most previous wheel–rail noise analysis has been conducted to mitigate those noises.However,in this paper,the noise is analysed to estimate the adhesion condition at the wheel–rail contact interface in combination with the other methodologies applied for this purpose.The adhesion level changes with changes in operational and environmental factors.To accurately estimate the adhesion level,the influence of those factors is included in this study.The testing and verification of the methodology required an accurate test prototype of the roller rig.In general,such testing and verification involve complex experimental works required by the intricate nature of the adhesion process and the integration of the different subsystems(i.e.controller,traction,braking).To this end,a new reduced-scale roller rig is developed to study the adhesion between wheel and rail roller contact.The various stages involved in the development of such a complex mechatronics system are described in this paper.Furthermore,the proposed brake control system was validated using the test rig under various adhesion conditions.The results indicate that the proposed brake controller has achieved a shorter stopping distance as compared to the conventional brake controller,and the brake control algorithm was able to maintain the operational condition even at the abrupt changes in adhesion condition.

Antiskid Control of Railway Train Braking Based on Adhesion Creep Behavior

In modern trains wheelset skidding leads to the deterioration of braking behavior,the degradation of comfort,as well as a boost in system hazards.Because of the nonlinearity and unknown characteristics of wheelset adhesion,simplifications are widely adopted in the modeling process of conventional antiskid controllers.Therefore,conventional antiskid controllers usually cannot perform satisfactorily.In this paper,systematic computer simulation and field tests for railway antiskid control system are introduced.The operating principal of antiskid control system is explained,which is fundamental to the simulation of antiskid brakes,and the simulation model is introduced,which incorporates both the adhesion creep curve and a pneumatic submodel of antiskid control system.In addition,the characteristics of adhesion curves and the simulation target are also provided.Using DHSplus,the pneumatic submodel is created to analyze the performance of the different control strategies of antiskid valves.Then the system simulation is realized by combining the kinematical characteristics of railway trains and the pneumatic submodel.The simulation is performed iteratively to obtain the optimized design of the antiskid control system.The design result is incorporated in the hardware design of the antiskid control system and is evaluated in the field tests in Shanghai Subway Line 1.Judging by the antiskid efficiency,the antiskid braking performance observed in the field tests shows the superiority of the optimized design.Therefore,the proposed simulation method,especially in view of its ease of application,appears to be a useful one for designing railway antiskid control systems.

Typical faults and safety analysis of brake controller for AC locomotive

Purpose–The brake controller is a key component of the locomotive brake system.It is essential to study its safety.Design/methodology/approach–This paper summarizes and analyzes typical faults of the brake controller,and proposes four categories of faults:position sensor faults,microswitch faults,mechanical faults and communication faults.Suggestions and methods for improving the safety of the brake controller are also presented.Findings–In this paper,a self-judgment and self-learning dynamic calibration method is proposed,which integrates the linear error of the sensor and the manufacturing and assembly errors of the brake controller to solve the output drift.This paper also proposes a logic for diagnosing and handling microswitch faults.Suggestions are proposed for other faults of brake controller.Originality/value–The methods proposed in this paper can greatly improve the usability of the brake controller and reduce the failure rate.

Design of the pressure regulation algorithm for active braking in vehicle ACC system

To develop the pressure control algorithm for active braking of adaptive cruise control（ACC） system,a test bench with real parts of the tested vehicle is built.With the dynamic analysis of the active braking actuators,it is demonstrated that different duty of pulse-width modulation（PWM） signals could control the pressure changing rate of the wheel cylinder.To obtain that signal,a modified proportional-integral-differential（PID） control algorithm is developed using the variable parameter method,the control value reset method,the dead zone method and the integral saturation method.Experimental results show that the delay and overshoot of the pressure response could be reduced considerably using the modified PID algorithm compared with the conventional one.The proposed pressure control algorithm could be used for the further development of the ACC＇s controller.

Longitudinal Control Strategy for Vehicle Adaptive Cruise Control Systems

A new longitudinal control strategy for vehicle adaptive cruise control （ACC） systems is presented. The running relationship between the ACC vehicle and the detected target vehicle is described by the relative velocity and the deviation between the actual headway distance and the prescribed safety distance. Based on this, two state space models are built and the linear quadratic optimal control theory is used to yield desired velocity for the ACC-equipped vehicle when with the target vehicle detected. By switching among four control modes, the desired velocity profile is designed to deal with different running situations. A velocity controller, which includes a PID controller for throttle openness and a neural network controller for brake application, is developed to achieve the desired velocity profile. The proposed control strategy is applied to a non-linear vehicle model in a simulation environment and is shown to provide the ACC vehicle comfortable ride and satisfying safety.

Control Algorithm of Electric Vehicle in Coasting Mode Based on Driving Feeling

Coasting in gear is a common driving mode for the conventional vehicle equipped with the internal combustion engine（ICE）, and the assistant braking function of ICE is utilized to decelerate the vehicle in this mode. However, the electric vehicle（EV） does not have this feature in the coasting mode due to the relatively small inertia of the driving motor, so it will cause the driver cannot obtain the similar driving feeling to that of the conventional vehicle, and even a traffic accident may occur if the driver cannot immediately adapt to the changes. In this paper, the coasting control for EV is researched based on the driving feeling. A conventional vehicle equipped with continuously variable transmission（CVT） is taken as the reference vehicle, and the combined simulation model of EV is established based on AVL CRUISE and MATLAB/Simulink. The torque characteristic of the CVT output shaft is measured in coasting mode, and the data are smoothed and fitted to a polynomial curve. For the EV in coasting mode, if the state of charge（SOC） of the battery is below 95%, the polynomial curve is used as the control target for the torque characteristic of the driving motor, otherwise, the required torque is replaced by hydraulic braking torque to keep the same deceleration. The co-simulation of Matlab/Simulink/Stateflow and AVL CRUISE, as well as the hardware-in-loop experiment combined with d SPACE are carried out to verify the effectiveness and the real-time performance of the control algorithm. The results show that the EV with coasting braking control system has similar driving feeling to that of the reference vehicle, meanwhile, the battery SOC can be increased by 0.036% and 0.021% in the initial speed of 100 km/h and 50 km/h, respectively. The proposed control algorithm for EV is beneficial to improve the driving feeling in coasting mode, and it also makes the EV has the assistant braking function.

汽车自适应巡航控制系统硬件在环仿真平台的设计与仿真试验（英文）

为了提高自适应巡航控制(ACC)系统的仿真精度,利用实车ACC系统的执行机构建立了硬件在环仿真(HILS)平台。HILS平台由仿真模型和硬件部分组成。仿真模型将运行在d SPACE仿真系统中,包括为了产生雷达模拟信号、ACC控制指令及计算车辆运行状态的雷达模拟器、ACC控制器和车辆模型。硬件部分主要包括电子节气门系统、主动制动系统及其附属的传感器及控制器等。通过串口通信接收来自ACC控制器的指令,HILS平台的硬件可以完成节气门开度和制动压力跟随控制。利用HILS平台进行了不同工况下的ACC仿真试验,仿真结果表明:HILS平台工作状况良好,并可以用于ACC控制器的开发。