Influence of heat-treatment on oxidation-resistance of phosphate-coating for C/C composite

Phosphate-coating was prepared for C/C composite using liquid-impregnation and different heat-treatment. The results show that the mass-loss rate of sample A with 1-2 ℃/min slow-cooling rate technology is 47%after oxidation at 700 ℃ for 20 h, while that of sample B with air-fast-cooling one is only 0.98%. SEM images reveal that the coating of sample A is full of micro-holes, micro-cracks and many piece-like crystal particles, while that of sample B is integrated and compacted in glassy state with a few of micro-cracks. The coating of sample A is almost exhausted only in 8 h oxidized-test at 700 ℃, while that of sample B remains integrated after 8 h test at 700 ℃ and becomes loose due to much small pores generated after 20 h test at 700 ℃.

Effect of Heat-Treatment Process on Properties of Rare Earth Mg-Based System Hydrogen Storage Alloys with AB_3-Type

The effect of heat-treatment process on the properties of Mm0.8Mg0.2(NiCoAlMn)3.5 hydrogen storage alloy was discussed . The electrochemical properties such as cycling stability, activation property, and the plateau voltage of the alloy which was heat-treated in various temperatures and times had different changes during the cycle process, the optimum heat-treatment conditions of this alloy were determined by this work.

Effects of Heat-treatment on Crystallization and Wear Property of Plasma Sprayed Fe-based Amorphous Coatings

The Fe-based amorphous coatings were produced by air plasma spraying. The as-sprayed coatings were heat-treated at the temperature of 573, 873, and 1 023 K, respectively. The crystallization and wear behavior of the heat-treated amorphous coatings were investigated. It was found that the amorphous- nanocrystalline transformation appeared when the as-sprayed coatings were treated at 853 K. The crystallization process had completed and a coating with microcrystallines was formed when the treatment temperature reached 1 023 K. The resultant amorphous and nanocrystalline composite coatings exhibited superior wear resistance compared to crystalline coating. It is attributed to fine grain strengthening of formed nanocrystallines.

Effects of Steam Heat-Treatment on Properties of Pinus massoniana Wood and Its Bonding Performance

Pinus massoniana wood was modified by steam heat-treatment at 160℃,180℃,200℃ and 220℃ respectively and effects of the changes of density,pH,surface wettability and apparent morphology of Pinus massoniana heat-treated wood on its bonding performance were studied in this paper.The results showed that Pinus massoniana wood underwent a series of physical and chemical changes during heat-treatment as the the following:(1)The degradation of hemicellulose and cellulose with low degree of polymerization,degradation and migration of the extract resulting in the decline of density and pH of heat-treated Pinus massoniana wood.(2)Brittle fracture occured on the cell wall surface,and the pit collapse,shrink and deformation,resulting in the formation of roughness and porosity on the wood surface.(3)The surface energy decreased with the improvement of temperature,the surface wettability of Pinus massoniana wood treated at 160℃–180℃ was good,while that at 200℃–220℃ showed hydrophobicity.(4)Changes of density,pH,surface roughness and porosity,and wettability resulted in a reduction in the bonding strength and reliability of heat-treated Pinus massoniana wood with MUF resin adhesive.(5)When the temperature was at 160℃–180℃,the better wettability of heat-treated Pinus massoniana wood could guarantee the better bonding performance.

Effect of Heat-treatment Temperature on HA-coated Titanium Materials

Homogeneous HA coating materials were prepared on porous titanium by the low-temperature combustion synthesis. It was found that the mechanical properties of the specimen depend on the coating process and the heat treatment, and the bending strength would be reduced during the coating process but could be improved by heat treatment. The effects of the temperature during heat- treatment on the phase composition and microstructure of the as-prepared coating, and the bending strength of the specimen were investigated by XRD and SEM. The experimental results show that in the coating process, slight oxidation of the substrate may give rise to a drop in bending strength ; however, it could be increased by the reaction of HA and TiO2 , and the sintering of the coating during heat treatment. The HA particles in the coating, with very fine sized particles. were pretty active and would decompose at 800℃.

EFFECT OF HEAT-TREATMENT ON THE MECHANICAL PROPERTIES OF AIN/SICw(Y_2O_3+SiO_2)COMPOSITE

In the paper, the effect of heat-treatment on the strength and toughness of AIN-SiC whisker composites with Y2O3 + SiO2 additives have been studied. When the Sample confining 10wt% Y2O3+SiO2(.Y2O3/SiO2^l/0. 66) -was treated at 1330癈 in air for 140 hours ithe flexural strength of composites ivas raised from 481 MPa to 784 MPa the toughness ruas also enhanced slightly. The phase composi-tion infrastructure and grain boundary phase structure have been char-acterized by combining XDR, SEM, TEM/EDXA and HREM tech-niques, reinforcenent and toughening mechanism of the composites re-sults from the crystallization of glass phase in the grain boundary at the high temperature oxidizing atmosphere to form the crossing struc-ture of 2H?sialon fibrous phase and SiC whisker

STUDY ON HEAT-TREATMENT OF AIN/SiC_w COMPOSITES AND EFFECTS ON MICROSTRUCTURE AND PROPERTIES

AlN-SiC whisker composites with Y2O3 and SiO2 additives were heat-treated at 1300 ℃ in air. The phase composition and microstrurture were analyzed using XRD, SEM and HREM techniques to study the effect of heat-treatment on the microstructure and properties of the composites. The results reveal that the mechanical properties and high temperature oxidation resistance of the composite of ivhich additives composition approaches the eutectic point of Y2O3-SiO2 can be improved through the heat-treatment. Glass phase in the grain boundary is observed to react with the surface composition of AlN forming fibrous 2Hδ Sialon, resulting a crossing structure produced by fibrous 2Hδ Sialon and SiC whiskers.

Effect of Seed Heat-Treatment on the Oxidative Stability of Canola Oil Body Emulsions

Enhancement of oxidative stability of canola oil extracted from seed subjected to prior heat-treatment has been attributed to heat-induced generation of antioxidants from phenolic precursors occurring in canola seed. Dispersion of aqueous extracts of intact seed oil bodies (OBs) in water is a novel and interesting way of producing natural and oxidatively stable food emulsions with minimal use of synthetic antioxidants and emulsifiers. As there is growing interest in natural food emulsions containing unsaturated oils, we investigated whether the oxidative stability of canola OB emulsions could be further improved by subjecting canola seed to heat-treatment prior to oil body extraction. Oil-in-water (5%, w/w) emulsions of OBs extracted from canola seed before and after heat-treatment were considerably more resistant to oxidation than emulsions prepared from refined canola oil and Tween? 40 emulsifier. However, only small amounts (0.9% - 4.5% by weight) of the phenolic compounds present in canola seed were transferred to the OBs after aqueous extraction, and consequently there was no discernible effect on oxidative stability as a result of prior heat-treatment of the seed. Thus, in contrast to oil, there is no oxidative stability benefit to be gained by subjecting canola seed to heat-treatment prior to extraction of OBs.

Brightness temperature simulation of subarctic lake-ice evolution by HIGHTSI and SMRT model

Microwave brightness temperature(TB)can be used to retrieve lake ice thickness in the Arctic and subarctic regions.However,the accuracy of the retrieval is affected by the physical properties of lake ice.To improve the understanding of how lake ice affects TB,numerical modeling was applied.This study combined a physical thermodynamic ice model HIGHTSI with a microwave radiation transfer model SMRT to simulate the TB and lake ice evolution in 2002-2011 in Hulun Lake,China.The reanalyzed meteorological data were used as atmospheric forcing.The ice season was divided into the growth period,the slow growth period,and the ablation period.The simulations revealed that TB was highly sensitive to ice thickness during the ice season,especially vertical polarization measurement at 18.7 GHz.The quadratic polynomial fit for ice thickness to TB outperformed the linear fit,regardless of whether lake ice contained bubbles or not.A comparison of the simulated TB with space-borne TB showed that the simulated TB had the best accuracy during the slow growth period,with a minimum RMSE of 4.6 K.The results were influenced by the bubble radius and salinity.These findings enhance comprehension of the interaction between lake ice properties(including ice thickness,bubbles,and salinity)and TB during ice seasons,offering insights to sea ice in the Arctic and subarctic freshwater observations.

A rapid assessment of MWRI-RM/FY3G brightness temperature

2023年4月发射的FY-3G上搭载17个频率的测雨微波成像仪(MWRI-RM),其业务定标的微波亮温(Tb)数据于2023年10月23日公开发布.本文比对了发布10天的MWRI-RM与全球降水测量(GPM)卫星上的微波成像仪(GMI)相匹配的Tb数据,并借助辐射传输模式进行双差分(DD)交叉定标分析,旨在快速评估新一代MWRI-RM观测数据质量.观测比较表明,MWR1-RM与GMI测量的Tb一致性很好,大多通道的平均偏差(MBE)和均方根误差(RMSE)均小于1K.两种传感器由于观测角度略有不同在水面产生约0.5 K差异.DD分析也展示出MWRI-RM的大多数通道性能与GMI相当接近,尤其是首次启用的高频166 GHz和183 GHz.

Synthesis and microwave absorption performance of heat-treated RF/SiO_(2)aerogels

The well-designed composite with satisfactory electromagnetic microwave absorption at high temperatures remains a serious challenge.Herein,we fabricated a resorcinol-formaldehyde/silica dioxide composite aerogel(RF/SiO_(2))with a three-dimensional network structure using sol-gel,atmospheric pressure drying technique as well as heat-treated processes to achieve enhanced microwave absorption capabilities in the low frequency range.The pristine RF/SiO_(2)aerogel presented a typical micropores structure with a surface area,porous volume,and density of 146.82 m^(2)/g,62.40%,and 0.28 cm^(3)/g,respectively.Remarkably,the RF/SiO_(2)aerogel showed an effective absorption bandwidth of 3.56 GHz and a minimum reflection loss value of-46.10 d B at 2.25 mm after being heat-treated at 1500°C,while the maximum effective absorption bandwidth was 3.60 GHz at 2.30 mm.The intricate three-dimensional networks possessed remarkable impedance matching,multiple attenuation mechanisms,interfacial polarization,and dielectric loss,which were attributed to the exceptional ability to absorb electromagnetic microwaves.It offered a fresh approach to creating adaptable and effective microwave absorption materials in military defense.

Asymptotic analysis on bright solitons and breather solutions of a generalized higher-order nonlinear Schrödinger equation in an optical fiber or a planar waveguide

We study a generalized higher-order nonlinear Schr¨odinger equation in an optical fiber or a planar waveguide.We obtain the Lax pair and N-fold Darboux transformation(DT)with N being a positive integer.Based on Lax pair obtained by us,we derive the infinitely-many conservation laws.We give the bright one-,two-,and N-soliton solutions,and the first-,second-,and Nth-order breather solutions based on the N-fold DT.We conclude that the velocities of the bright solitons are influenced by the distributed gain function,g(z),and variable coefficients in equation,h_(1)(z),p_(1)(z),r_(1)(z),and s_(1)(z)via the asymptotic analysis,where z represents the propagation variable or spatial coordinate.We also graphically observe that:the velocities of the first-and second-order breathers will be affected by h_(1)(z),p_(1)(z),r_(1)(z),and s_(1)(z),and the background wave depends on g(z).

Evaluating the Effects of Graviton Redshift upon Spiral Galaxy Rotation Curves, Surface Brightness Magnitudes and Gravitational Lensing

The effects of the gravitational redshift of gravitons upon spiral galaxy rotation energy are compared to the standard mass to light analyses in obtaining rotation curves. The derivation of the total baryonic matter compares well with the standard theory and the rotation velocity is matched to a high precision. The stellar mass distributions obtained from the fit with graviton energy loss are used to derive the surface brightness magnitudes for the galaxies, which agree well with the observed measurements. In a new field of investigation, the graviton theory is applied to the observations of gravitational lenses. The results of these applications of the theory suggest that it can augment the standard methods and may eliminate the need for dark matter.

Heat-treated wood and its development in Europe

Efficient use of timber is a vital concern problem, especially in these regions where the forestry coverage ratio is decreasing. Studies on physical modification of wood have been taken more attention due to the increasing attentions on environmental protection. Thermal modification is emphasized and developed quickly in developing countries, especially in European countries. A large number of researches have been conducted and some industrial production plants have been built. This paper reviewed the history of heat treatment, exemplifies the industrial developments in several European countries, summarized the basic principle of heat treatment and describes the environmental characteristics. The properties of heat-treated wood and its usage are also summed up.

Electrodeposition behavior of bright nickel in air and water-stable betaine·HCl-ethylene glycol ionic liquid

The electrodeposition behaviors of nickel on glassy carbon（GC） and carbon steel（CS） electrodes were investigated in the14.3%-85.7%（mole fraction） betaine.HCl ethylene glycol（EG） ionic liquid using cyclic voltammetry and chronoamperometry.The results indicated that the reduction of Ni（Ⅱ） on CS electrode via a diffusion-controlled quasi-reversible process was much more facile and easier than that occurred on GC electrode,which followed a diffusion-controlled three-dimensional instantaneous nucleation and growth.Scanning electron microscopy was used to observe that the deposit was dense and contained fine crystallites with average size of（80±4） nm.Energy dispersive spectrometer analysis showed that the obtained deposit was metallic nickel.X-ray diffraction spectroscopy indicated that（111） plane was the most preferred crystal orientation.The nickel deposit was luminous and bright,and had good adhesion with the CS substrate.

脐血中CD56^(bright)CD16^(dim)/^-NK细胞亚群的检测

目的了解新生儿脐血NK细胞和CD56bright CD16dim/-NK细胞亚群的比率,探讨CD56bright CD16dim/-NK细胞在脐血低免疫应答中的作用。方法使用血细胞分析仪计数淋巴细胞;采用流式细胞术检测脐血、母亲及对照组中NK细胞和CD56bright CD16dim/-NK细胞亚群的比率。结果脐血中淋巴细胞计数显著高于母亲及对照组;NK细胞比率无显著性差异;CD56bright CD16dim/-NK细胞高于母亲及对照组;母亲组CD56bright CD16dim/-NK细胞高于对照组。结论脐血中丰富的CD56bright CD16dim/-NK细胞是脐血低免疫应答的原因之一。

Bright Yellow 2烤烟热激蛋白90生物信息学分析

【目的】分析Bright Yellow 2烤烟热激蛋白90(HSP90)的生物学信息,为揭示烘烤过程中烟叶的烘烤特性提供理论依据。【方法】从NCBI中获取Bright Yellow 2烤烟HSP90蛋白序列Nt HSP-1、Nt HSP-2和Nt HSP-3(Gen Bank登录号分别为BAL42333、BAL42332和BAM24708),利用生物信息学软件对各序列进行理化特性、跨膜区、信号肽、亚细胞定位、二级结构和三级结构预测分析。【结果】Bright Yellow 2烤烟Nt HSP-1、Nt HSP-2和Nt HSP-3的氨基酸数量分别为812、811和699个,均以酸性氨基酸含量较多,其中谷氨酸(Glu)含量最高,理论等电点均小于5.00,二级结构均以α-螺旋(H)和无规则卷曲(C)为主。Nt HSP-1和Nt HSP-2的亲水性较高,具有较高的稳定性,属于分泌蛋白,具有锚定结构,定位于内质网,其三级结构呈现"r"形,N端内部具有Mg2+结合位点、HATPase_c(ATP酶)和top6b(DNA拓扑异构酶VI)功能域;Nt HSP-3为非分泌型蛋白,定位于叶绿体,三级结构呈现"i"形,N端含有Mg2+结合位点和HATPase_c功能域。【结论】Nt HSP-1和Nt HSP-2可能与烟叶耐烤性有关,而Nt HSP-3可能与烟叶易烤性有关。

High Brightness,High Power Density Fiber Coupling of High Power Laser Diode

The output radiation from the 100μm×1μm aperture of a high power Laser Diode (LD) is efficiently coupled into a 50μm multimode optical fiber.The fiber output of the high power LD with high brightness and high power density is achieved.The power density is up to 3 6×104W/cm2 and the coupling efficiency is 70%.The extreme divergence and the astigmatism of high power LDs require the optics with complex lens structures and high performance.A double-curved lens with two crossed cylindrical lenses structured on both sides of the glass substrate is used in the coupling system.

基于图像融合的井下视频增强技术

在油气田开采过程中,面临套管损坏、井下落物等诸多问题。为了能够更加精准地了解井下环境状况,在现实的油气井开发过程中,通常会采取可视化测井仪对井下油气管道进行检测。但是由于井下环境、水质等因素会影响可视化测井仪所采集的井下视频的清晰度,为了提升可视化测井仪的视频清晰度,介绍了一种水下图像融合增强技术,通过对井下视频进行处理增强。经实验可知其处理每帧图片需用时约0.7 s,且井下视频的对比度、清晰度有了较大提升,从而帮助后续的修井作业精准地找到“病症问题”,保障修井作业的顺利进行,大大提高了油气井的使用寿命及开采效率。

Effect of lanthanum on microstructure of a nickel-based single crystal superalloy

To enhance the high-temperature oxidation resistance and mechanical properties of a secondgeneration nickel-based superalloy,various concentrations of lanthanum(La)ranging from 5.0×10^(-5)wt.%to 3.4×10^(-4)wt.%are added to the alloy.The microstructure of the nickel-based single crystal superalloy with trace of La was examined by means of SEM,EDS and TEM.Results show the addition of La decreases the segregation of elements and increases the amount ofγ/γ′eutectics of the as-cast alloy,and in the interdendritic region,the growth of eutectics is accompanied by the growth of strip clusters composed of Ni_(5)La and Ni_(3)Ta.As the La content in the alloy increases,the proportion of Ni_(5)La in the cluster increases.After heat treatment,incipient melting occurs in the cluster regions,leading to an increase in microporosity compared to the original as-cast samples.Furthermore,the heat treatment alters the shape of the clusters from a strip morphology to an elliptical one,and it changes their composition from Ni_(5)La and Ni_(3)Ta to a combination of Ni_(5)La,Ni_(3)Ta,and MC carbides.