History and Development of Zhuang Medicine Shallow Needling from Bone Needle,Pottery Needle,and Bronze Needle to Electroacupuncture

Zhuang medicine shallow needling has a long history and plays a significant role in Chinese medicine.With the development of medical treatment in China,there is a constant improvement in the use of needles.Bone needles have been modified to pottery needles,bronze needles,and electroacupuncture.From this long development history,there are some improvements in terms of material and technology.By analyzing and comparing the primitive and current acupuncture instruments used in China and their therapeutic effects,it can be seen that China’s medical treatment is constantly improving and will continue to improve with technology.

In-situ investigation of atmospheric corrosion behavior of bronze under thin electrolyte layers using electrochemical technique

The atmospheric corrosion behavior of bronze under thin electrolyte layer （TEL） with different thicknesses was monitored using cathodic polarization curves, open circuit potential （OCP） and electrochemical impedance spectroscopy （EIS）. Cathodic polarization result indicates that the cathodic limiting current density increases with decreasing the TEL thickness. EIS result shows that the corrosion rate increases with decreasing the TEL thickness at the initial stage because the corrosion is dominated by the cathodic process, whereas after long immersion time, the corrosion degree with the TEL thickness is in the sequence of 150 μm 〉 310 μm〉 10μm ≈ bulk solution 〉 57 μm. The measurements of OCP and EIS present in-situ electrochemical corrosion information and their results are in good agreement with that of physical characterizations.

Effects of Ce in novel bronze and its plasma sprayed coating

A novel aluminum bronze over the Cu-Al binary alloy eutectoid Cu-14Al-4.5Fe was prepared by a jointly-charging one-melting technique and conventional sand casting. The bronze coatings were atmospherically plasma sprayed on the 45# medium carbon steel substrate. The effect of rare earth Ce on the microstructures and Vickers hardness of the cast alloy and coatings were characterized by scanning electron microscopy, X-ray diffraction, electronic probe microanalysis, transmission electron microscopy and microhardness measurements. The results indicate that the hardness of both as-cast alloy and coating are enhanced by the addition of 0.6% Ce due to the refinement of κ phases which are well distributed in the matrix. The rapid solidification in the plasma spray processing retains Fe-supersaturated in the Al-bronze alloy coatings, which avoids the formation of eutectoid （α＋γ2） phase and stacking faults are found in the coatings with Ce added, accordingly improves the mechanical properties.

Identification of constitutive model parameters for nickel aluminum bronze in machining

The material of nickel aluminum bronze (NAB) presents superior properties such as high strength, excellent wear resistance and stress corrosion resistance and is extensively used for marine propellers. In order to establish the constitutive relation of NAB under high strain rate condition, a new methodology was proposed to accurately identify the constitutive parameters of Johnson?Cook model in machining, combining SHPB tests, predictive cutting force model and orthogonal cutting experiment. Firstly, SHPB tests were carried out to obtain the true stress?strain curves at various temperatures and strain rates. Then, an objective function of the predictive and experimental flow stresses was set up, which put the identified parameters of SHPB tests as the initial value, and utilized the PSO algorithm to identify the constitutive parameters of NAB in machining. Finally, the identified parameters were verified to be sufficiently accurate by comparing the values of cutting forces calculated from the predictive model and FEM simulation.

STRUCTURE OF BLACK PATINA ON THE ANCIENT BRONZE MIRRORS

X-ray diffaction analysis(XRDA)data of the black or brown patina on the surfaces of eight kinds of bronze mirror samples show 4 or 5 broad diffuse peaks which corresponding to almost the same 20 angle, while their matixes does not.These results indicate that those diffuse peaks were produced by the SnO2, microcrystals of 3 ￣5 nm size contained in the black or brown patina.The matrix of unearthed black patina bronze mirror numbered 223, gives strong XRDA diffraction peaks, indicating that there are a large amounts of non-oxidized bronze alloy particles surrounded by SnO2,which shows that the black patinas are not wholly metallic oxides (mainly SnO2),there are also a lot of original alloys of different sizes in grain in the patina.The bright-field image of the black patina sample gives the same result.

Synchronous organic-inorganic co-intercalated ammonium vanadate cathode for advanced aqueous zinc-ion batteries

Vanadium-based cathode materials are attractive for aqueous zinc-ion batteries(AZIBs)owing to the high capacity from their open frameworks and multiple valences.However,the cycle stability and rate capability are still restricted by the low electrical conductivity and trapped diffusion kinetics.Here,we propose an organic-inorganic co-intercalation strategy to regulate the structure of ammonium vanadate(NH_(4)V_(4)O_(10),NVO).The introduction of Al^(3+)and polyaniline(PANI)induces the optimized layered structure and generation of urchin-like hierarchical construction(AP-NVO),based on heterogeneous nucleation and dissolution-recrystallization growth mechanism.Owing to these favorable features,the AP-NVO electrode delivers a desirable discharge capacity of 386 mA h g^(-1) at 1.0 A g^(-1),high-rate capability of 263 mA h g^(-1 )at 5.0 A g^(-1) and excellent cycling stability with 80.4%capacity retention over 2000 cycles at 5.0 A g^(-1).Such satisfactory electrochemical performance is believed to result from the enhanced reaction kinetics provided by the stable layered structure and a high intercalation pseudo-capacitance reaction.These results could provide enlightening insights into the design of layered vanadium oxide cathodematerials.

Translation Skills of Children’s Literature from the Perspective of Recep tion Theory:A Case Study of Bronze and Sunflower

With the development of society and the prosperity of Chinese literature,as a part of China’s soft power,Chinese chil dren literature is faced with the problem of international dissemination.The English version of Cao Wenxuan’s Bronze and Sunflow er won Hans Christian Andersen Award,the top award of children’s literature,which is a successful example of such dissemina tion.Therefore,the Chinese-English translation skills employed are worth studying.This paper aims to analyze the skills used to in the translation of short clauses,reiterative locution,simile,parallelism and dingzhen from the perspective of reception theory.It is found that by using such translation skills as omission,alliteration,repetition of prepositions and pronouns,and literal translation,the translator preserves and recreates the effect of the original text in ways that are more acceptable and idiomatic for the target reader.

Size effects on deformation behavior of C5210 phosphor bronze thin sheet

To investigate the effects of thickness and grain size on mechanical and deformation properties of C5210 phosphor bronze thin sheets, samples with different grain sizes were obtained through annealing heat treatment at different temperatures; and then tensile tests of samples with different thicknesses and grain sizes were conducted at room temperature. The results show that yield strength increases with decreasing thickness from 800 to 50 μm, but work hardening exponent and total elongation decrease, and a modified model was proposed to describe the relation between yield strength and thickness; yield strength decreases as the grain size increases, but work hardening exponent shows an increasing trend, total elongation increases to a peak and then decreases. Fracture morphology of tensile specimens was observed by SEM, which indicates that all tensile specimens are ductile fracture. The dimple intensity increases as the specimen thickness increases but reduces with the specimen grain size increasing.

DIFFUSION COUPLE BETWEEN HIGHSTRENGTH WEAR-RESISTING ALUMINUM BRONZE AND MACHINING TOOLS MATERIALS

ＩＮＴＲＯＤＵＣＴＩＯＮＡｌｕｍｉｎｕｍｂｒｏｎｚｅｉｓａｎｉｍｐｏｒｔａｎｔｅｎｇｉｎｅｅｒｉｎｇｍａｔｅｒｉａｌ．Ｉｔｓｅｘｃｅｌｅｎｔｐｈｙｓｉｃａｌ，ｍｅｃｈａｎｉｃａｌ，ａｎｔｉｃｏｒｏｓｉｏｎａｎｄｗｅａｒｒｅｓｉｓｔｉｎｇｐｒｏｐ...

Corrosion performance and tribological behavior of diamond-like carbon based coating applied on Ni−Al−bronze alloy

The effect of diamond-like carbon(DLC)coating(fabricated by cathodic arc deposition)on mechanical properties,tribological behavior and corrosion performance of the Ni−Al−bronze(NAB)alloy was investigated.Nano-hardness and pin-on-plate test showed that DLC coating had a greater hardness compared with NAB alloy.Besides,the decrease in friction coefficient from 0.2 for NAB substrate to 0.13 for the DLC-coated sample was observed.Potentiodynamic polarization and EIS results showed that the corrosion current density decreased from 2.5μA/cm2 for bare NAB alloy to 0.14μA/cm2 for DLC-coated sample in 3.5 wt.%NaCl solution.Moreover,the charge transfer resistance at the substrate−electrolyte interface increased from 3.3 kΩ·cm2 for NAB alloy to 120.8 kΩ·cm2 for DLC-coated alloy,which indicated an increase in corrosion resistance due to the DLC coating.

Grain refinement of bronze alloy by equal-channel angular pressing(ECAP) and its effect on corrosion behaviour

The corrosion behaviour of bronze alloy prepared by equal channel angular pressing(ECAP) was investigated in 3.5 wt. % Na Cl solution.Immersion corrosion tests and different electrochemical techniques were carried out. The results showed that ECAPed bronze samples exhibited higher corrosion resistance compared with the as-cast alloy and the passive current density decreased with increasing number of passes. Moreover,the morphology of alloys indicated that the corrosion damage on the surface of ECAPed bronze was smooth and uniform while the as-cast alloy suffered from selective corrosion.

Formation and Oxidation of Hydrogen Molybdenum Bronze on Platinum Electrode in Sulfuric Acid Solution

Hydrogen molybdenum bronze (HxMoO3) can be electrodeposited on platinum and oxidized in two steps to the hydrogen molybdenum bronze with less amount of hydrogen HyMoO3 (y<x) and MoO3 when platinum electrode is cycled from -0.2 to 1.3V (vs. SCE) in 0.05 mol/L Na2MoO4 + 0.5 mol/L H2SO4 solution. During the formation of HxMoO3, the electrochemical reduction of molybdate existing in the form of polymolydate is reversible and is about a five-electron transfer reaction.

Effect of RE on Cast Structure and Properties of High Manganese Aluminium Bronze

The effects of various amount of Y and La on the cast structure.the fluidity,the wearability and corrosion resistance of the high manganese aluminium bronze have been investigated.The results have shown that a proper content of rare earth elements is able to refine the cast structure of the alloy,and furthermore to enhance its wearability and corrosion resistance.The reasons for these phenomena have also been discussed.

Microstructural characterization of blanked surface of C5191 phosphor bronze sheet under ultra-high-speed blanking

The deformation mechanism of C5191 phosphor bronze sheet under ultra-high-speed blanking was investigated.By virtue of a DOBBY-OMEGA F1 ultra-high-speed press,the ultra-high-speed blanking test was conducted on C5191 phosphor bronze sheets with a thickness of 0.12 mm at 3000 strokes per minute.The microstructures of the blanked edges were characterized and analyzed separately by electron back-scatter diffraction(EBSD)and transmission electron microscopy(TEM).The results show that grains in the blanked edges are stretched along the blanking direction.Strong{001}<100>cube textures(maximum pole densities of 9 and 12,respectively)and secondarily strong{011}<011>textures(maximum pole densities of 4 and 7,respectively)are formed in local zones.Additionally,deformation twins are found in the shear zone of the blanked edges which are rotated and coarsened due to the blanking-induced extrusion and local thermal effect which can further form into sub-grains with clear and high-angle boundaries.The C5191 phosphor bronze sheet is subjected to adiabatic shear during ultra-high-speed blanking,accompanied with dynamic recrystallization.

Preparation and performance of a cold gas dynamic sprayed high-aluminum bronze coating

By mixing preheated high-aluminum bronze powders with different amounts of Al_2O_3 powder, a low-pressure cold-sprayed coating was prepared and sprayed onto a Cr12MoV steel substrate. The hardness of the coating and the bonding strength between the coating and the substrate were tested with a HV-1000 microhardness tester and a mechanical universal testing machine. The surface microstructure, cross-section and tensile fracture surface of the coating were observed with a scanning electron microscope(SEM). Correspondingly, the influences of the preheat treatment temperature of the bronze powder and the Al_2O_3 content on the coating performance were investigated. The results indicate that the hardness of bronze powders decreased and the coating deposition rate increased after the preheating treatment of the bronze powder. The Al_2O_3 content in the mixed powders contributed to the deformation of bronze powders during the spraying process. This trend resulted in varied performance of the coating.

Effect of filler metal on microstructure and mechanical properties of manganese-aluminum bronze repair welds

The repair welding of UNS C95700manganese?aluminum bronze plates was done using different filler metals.Themicrostructure and mechanical properties of welds were studied.The main microstructural constituents wereα,βandκphases withdifferent morphologies.The addition of manganese decreased the percentage ofαphase in the microstructure of weldments from80%(Mn-free weld)to57%(12.5%Mn weld,mass fraction).The morphology ofκphase was lamellar in high nickel specimens andit was changed to a globular morphology for high manganese welds.Although the application of high manganese filler metal yieldedthe higher tensile and bending strengths of weldment compared with the weld using high nickel filler material,the optimummechanical properties of repair welds were obtained using a non-alloy filler material(ERCuAl-A2)for the underlay and highmanganese filler metal(ERCuMnNiAl)for filling passes.This weld presented an increase of39%in tensile strength compared withthe base metal,and no cracking was observed after bending test.

Microstructure evolution of Nb_3Sn superconductors during diffusion treatment by bronze route

The element diffusion process of Nb_3Sn superconductors by bronze route was studied using X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy. The critical current of superconductors was measured by four-point method. The results show that a diffusion layer has formed around the boundaries between the filaments and bronze matrix after 15 h heat treatment. The diffusion layer thickness keeps stable after heat treatment duration of 50~75 h. The stable and solid Nb 3 Sn layer is obtained in the sample after 100 h heat treatment. Excessive heat treatment would induce superconductivity degeneration because of superconductor grain coarsening. The characteristics of the element diffusion process were discussed. The diffusion of tin atom is the governing factor in diffusion. In this study, Nb_3_Sn superconductors with good superconducting property were fabricated successfully at 670 °C after 100h heat treatment.

Elements inter-diffusion in the turning of wear-resistance aluminum bronze

Inter-diffusion of elements between the tool and the workpiece during theturning of aluminum bronze using high-speed steel and cemented carbide tools have been studied. Thetool wear samples were prepared by using M2 high-speed steel and YW1 cemented carbide tools to turna novel high strength, wear-resistance aluminum bronze without coolant and lubricant. Adhesion ofworkpiece materials was found on all tools' surface. The diffusion couples made of tool materialsand aluminum bronze were prepared to simulate the inter-diffusion during the machining. The resultsobtained from tool wear samples were compared with those obtained from diffusion couples. Stronginter-diffusion between the tool materials and the aluminum bronze was observed in all samples. Itis concluded mat diffusion plays a significant role in the tool wear mechanism.

High Temperature Gaseous Rare-Earth Permeation of Polyoxotungstates: An New Effective Method for the Preparation of Tungsten Bronzes

New polyoxometalate α-K 12H 3[Y(BW 11O 39) 2]·25H 2O was synthesized and treated by high temperature gaseous rare earth permeation to prepare tungsten bronze K 0.475WO 3. XRD, TG-DTA, XPS, 183W-NMR,CV and AC impedance spectra were used to characterize the resulting material. The results of XPS indicate that La has permeated and diffused into the body of the sample and exists in the forms of binding with other components. The crystal structure parameters of K 0.475WO 3 were obtained by the analysis of XRD, which shows tetragonal crystal system with lattice parameters: a=12 28 nm, c=3.833 nm, V=578.48 nm -3. The conductivities calculated from the results of AC impedance spectra of the material increase with the increasing of temperature, which shows a semiconductor character.

Correlation between microstructure and corrosion and cavitation erosion behaviors of nickel aluminum bronze

The microstructure,corrosion and cavitation erosion(CE)behaviors of the as-cast and four different heat treated nickel aluminum bronzes(NABs)in 3.5 wt.%NaCl solution were investigated.The results show that after annealing,β′transformed into the eutectoid microstructure,and moreκIV precipitated fromα.Less eutectoid microstructure and moreβ′were obtained after normalizing.The quenched NAB mainly consisted ofαandβ′phases,and fine,acicularαandκphases precipitated insideβ′after subsequent aging.The largest proportion of the eutectoid microstructure,which underwent severe selective phase corrosion,was responsible for the lowest corrosion resistance of the annealed NAB.The quenched NAB possessed the most protective film and hence the highest corrosion resistance.The mechanical attack was primarily responsible for the CE damage for the as-cast,annealed and normarlized NABs.The quenched and quenched+aged NABs exhibited superior CE resistance because of the high hardness.The CE−corrosion synergy dominantly caused CE degradation,and it was largely attributed to corrosion-enhanced-CE.