Research on Control Strategy of Grid-connected Brushless Doubly-fed Wind Power System Based on Virtual Synchronous Generator Control

The brushless doubly-fed wind power system based on conventional power control strategies lacks ‘inertia’ and the ability to support grid,which leads to the decline of grid stability.Therefore,a control strategy of brushless doubly-fed reluctance generator(BDFRG) based on virtual synchronous generator(VSG) control is proposed to solve the problem in this paper.The output characteristics of BDFRG based on VSG are similar to a synchronous generator(SG),which can support the grid frequency and increase the system ‘inertia’.According to the mathematical model of BDFRG,the inner loop voltage source control of BDFRG is derived.In addition,the specific structure and parameter selection principle of outer loop VSG control are expounded.The voltage source control inner loop of BDFRG is combined with the VSG control outer loop to establish the overall architecture of BDFRG-VSG control strategy.Finally,the effectiveness and feasibility of the proposed strategy are verified in the simulation.

Robust Position Observer for Sensorless Direct Voltage Control of Stand-Alone Ship Shaft Brushless Doubly-Fed Induction Generators

The aim of this paper is to investigate an adaptive sensorless direct voltage control(DVC)strategy for the stand-alone ship shaft brushless doubly-fed induction generators(BDFIGs).The proposed new rotor position observer using the space vector flux relations of BDFIG may achieve the desired voltage control of the power winding(PW)in terms of magnitude and frequency,without any speed/position sensors.The proposed algorithm does not require any additional observers for obtaining the generator speed.The proposed technique can directly achieve the desired DVC based on the estimated rotor position,which may reduce the overall system cost.The stability analysis of the proposed observer is investigated and confirmed with the concept of quadratic Lyapunov function and using the multi-model representation.In addition,the sensitivity analysis of the presented method is confirmed under different issues of parameter uncertainties.Comprehensive results from both simulation and experiments are realized with a prototype wound-rotor BDFIG,which demonstrate the capability and efficacy of the proposed sensorless DVC strategy with good transient behavior under different operating conditions.Furthermore,the analysis confirms the robustness of the proposed observer via the machine parameter changes.

Controller Design for Induction and Brushless Motors Using Matlab with Digital Signal Processor (DSP)

The automation process is a very important pillar for Industry 4.0.One of the first steps is the control of motors to improve production efficiency and generate energy savings.In mass production industries,techniques such as digital signal processing(DSP)systems are implemented to control motors.These systems are efficient but very expensive for certain applications.From this arises the need for a controller capable of handling AC and DC motors that improves efficiency and maintains low energy consumption.This project presents the design of an adaptive control system for brushless AC induction and DC motors,which is functional to any type of plant in the industry.The design was possible by implementing Matlab software and tools such as digital signal processor(DSP)and Simulink.Through an extensive investigation of the state of the art,three models needed to represent the control system have been specified.The first model for the AC motor,the second for the DC motor and the third for the DSP control;this is done in this way so that the probability of failure is lower.Subsequently,these models have been programmed in Simulink,integrating the three main models into one.In this way,the design of a controller for use in AC induction motors,specifically squirrel cage and brushless DC motors,has been achieved.The final model represents a response time of 0.25 seconds,which is optimal for this type of application,where response times of 2e-3 to 3 seconds are expected.

Suppression of thrust fluctuation of doubly-fed linear motor

Because the mover and stator of a doubly-fed linear motor are both equipped with three-phase windings, the motor enables contactless energy to be transferred from the stator to the mover. Thus, when a doubly-fed linear motor is used in the linear driving system of trains, neither an overhead line nor a third rail is needed. However, the doubly- fed motor will lead to more severe thrust fluctuation than the unilateral motors. In order to overcome this shortcoming, the thrust fluctuation of the doubly-fed motor should be analyzed. In this paper, an expression for motor thrust is derived. It points out that the slot effect caused by the slotted structure is the main reason for the increase of thrust fluctuation. The method of adopting unequal pole pitch and unequal slot numbers per pole per phase of stator and mover, is proposed to weaken the slot effect when designing the motor slot parameters. Three different motor models are simulated by ANSOFT. The proposed method results in a motor thrust fluctuation coefficient of 8.4%, compared to 49.4% for the conventional method. Therefore, the motor＇s thrust fluctuation is effectively suppressed by the proposed method.

Brushless Doubly-Fed Induction Machine as a Variable Frequency Transformer

VFT （variable frequency transformer） has been recently used as art alternative to HVDC （high voltage direct current） to control power flow between asynchronous networks. VFT consumes less reactive power than a back-to-back HVDC system, provides faster initial transient recovery, and has better natural damping capability. VFT is simply a DFIM （doubly-fed induction machine） where the machine torque controls the power flow from stator to rotor and vice versa. The main disadvantage of this VFT is the slip rings and brushes required for the rotor circuit, especially in bulk power transmission. The BDFM （brushless doubly-fed machine） with nested cage rotor machine is proved to be a comparable alternative to conventional DFIM in many applications with the advantage that all windings being in the stator frame with fixed output terminals. In this paper, the BDFM is used as a BVFT （brushless variable frequency transformer）. A prototype machine is designed and simulated to verify the system validity.

New Method to Restrain Pumping Voltage of Braking Procedure for Brushless DC Motor of Electric Armored Vehicle

In order to restrain the high pumping voltage of braking procedure which is harmful to the system of electric armored vehicle. Based on the analysis of pumping voltage of the braking procedure, the relation between pumping voltage and PWM ratio is derived and a new digital control method to restrain the pumping voltage by changing PWM ratio is put forward. Because the capacitance is decreased effectively, the volume of controller is reduced and the performance to price ratio is improved. The results of computer simulation and experiment proved that this method is feasible and valid.

Simulation Research of Fault Model of Detecting Rotor Dynamic Eccentricity in Brushless DC Motor Based on Motor Current Signature Analysis

基于Ansoft／Maxwell设置动态偏心故障，建立求解电机电感和磁链的有限元模型，通过仿真，证明了将感应电机动态偏心故障的特征频率经过简化后，同样适用于无刷直流电动机。基于Ansoft／Simplorer建立无刷直流电动机系统的仿真模型。在电机稳态运行下，对定子电流进行傅里叶分析，研究并建立基于定子电流监测动态偏心故障的仿真模型：动态偏心故障与特征频率的关系、动态偏心故障程度与特征频率幅值的关系。进而研究了无刷直流电动机稳态运行时转速波动对偏心故障监测的影响。仿真结果表明，转子偏心程度加大，特征频率的幅值增加。

Anti-reverse rotation startup method for sensorless brushless DC motor

In order to start up the brushless DC motor （BLDCM） without reverse rotation and smoothly switch the running state of the motor, a novel startup and smoothly switching method for a sensodess BLDCM is presented. Based on the saturation effect of the stator iron, six short voltage pulses are applied to determine the initial rotor position and the rotor can be found within 60°. After that, a series of short and long voltage pulses are used to accelerate the motor and the variation of the response current is utilized to detect the rotor position dynamically. When the motor reaches a certain speed at which the back-electromotive force （EMF） method can be applied, all the power devices are turned off and the running state of the motor is smoothly switched at the moment determined by the relationship between the terminal voltage waveform and the commutation phases. The experimental results verify the feasibility and validity of the proposed method.

EFFECTIVE DOUBLE LOOP CONTROL FOR A SQUARE WAVE BRUSHLESS DC MOTOR

A new type of brushless DC motor has been developed by using a square wave rare earth permanent magnet synchronous motor with its double loop control circuit. The double loop control scheme of the drive system yields a combination of desired characteristics including simplified control structure, small ripple torque, high speed accuracy, wide operating speed range, and fast dynamic response. Experimental results confirm excellent characteristics of the motor.

Robust Control Strategy for the Speed Control of Brushless DC Motor

Brushless DC motor ( BLDCM) speed servo system is multivariable,nonlinear and strong coupling. The parameter variation, the cogging torque and the load disturbance easily influence its performance. Therefore,it is difficult to achieve superior performance by using the conventional PID controller. To solve the deficiency,the paper represents the algorithm of active-disturbance rejection control ( ADRC) based on back-propagation ( BP) neural network. The ADRC is independent on accurate system and its extended-state observer can estimate the disturbance of the system accurately. However,the parameters of Nonlinear Feedback ( NF) in ADRC are difficult to obtain. So in this paper,these parameters are self-turned by the BP neural network. The simulation and experiment results indicate that the ADRC based on BP neural network can improve the performances of the servo system in rapidity,control accuracy,adaptability and robustness.

Integrated design of brushless motor drive and control system for robot joints

To meet the requirements of high performance, low cost, and easy operation of the robot, a brushless motor drive and control system for the robot joint is designed, including CAN bus, WPF upper host computer development, and magnetic encoders, and other sensors, in which the STM32 F103 chip is used as the main control chip, and the DRV8323 is a brushless motor drive chip. The principle of field-oriented control(FOC) brushless motor drive is elaborated.Meanwhile, the drive and control system design is completed from both hardware and software aspects. Finally, the PID algorithm is used for the closed-loop speed test of the robot joint. The experimental result shows that the designed robot joints and control system run smoothly and reliably, have the characteristics of modularization and miniaturization, and are suitable for the control of micro-service robots and manipulators.

Torque Ripple Suppression Control Strategy for Brushless Integrated Starter/Generator Wound-Field Synchronous Motor

A flux linkage compensation field oriented control (FOC) method was proposed to suppress the speed and torque ripples of a brushless wound-field synchronous motor in its starting process. The starting process was analyzed and the model of wound-field synchronous electric machine was established. The change of field current of the electric machine was described mathematically for simplified exciter and rotate rectifier. Based on the traditional field control, the flux linkage compensation was introduced in d-axis current to counteract the flux ripple. Some simulation and preliminary experiments were implemented. The results show that the proposed method is feasible and effective.

Comparative Study between the PID Regulator and the Fuzzy Regulator Applied to the Operation of a Brushless DC Motor

This paper presents the results of research on speed regulation of a brushless DC motor. This is mainly a comparative study between a PID regulator and a fuzzy regulator applied to the operation of this type of engine in order to find the best control. The BLDC engine must operate under various speed and load conditions with improved performance and robust and complex speed control. Because of this complexity, the traditional PID command encounters difficulties in controlling the speed of a BLDC. Another control technique is currently developing and is producing good results. This is the fuzzy controller that handles process control problems, that is, managing a process based on a given set point per action on the variables that describe the process. To achieve the desired results, the brushless DC machine model will be studied. With the model obtained, both types of regulator will be tested. A synthesis of the observed comparison results will enable a conclusion to be drawn on the performance of the two types of regulators driving a BLDC (Brushless DC).

Design optimization of a slotless PM brushless motor with helical edge wound laminations for rim driven thrusters

This paper discusses the analysis and design of a very thin slotless permanent magnet （PM） brushless motor whose stator laminations are manufactured from a single strip of steel that is edge wound into a spiral （like a ＂Slinky＂） and then fitted over the windings that are preformed on the outside surface of a non-conducting former. Analytical and finite element analysis （FEA） are used to determine the con- strained optimum dimensions of a motor used to drive a rim driven thruster in which the motor rotor is fit- ted onto the rim of the propeller and the stator is encapsulated in the thin Kort nozzle of the thruster. The paper describes the fabrication of a demonstrator motor and presents experimental results to validate the theoretical calculations. Experimental motor performance results are also reported and compared with those of a slotted motor that fits within the same active radial dimensions as the slotless motor. The slotless motor, which has longer active length and endwindings, and thicker magnets than the slotted motor, was found to be less efficient and more expensive （prototype cost） than the slotted machine.

An Advance Commutation Control Method for Low Torque Ripple of Brushless DC Motors

该文给出一种优化的无刷直流电动机变母线电压六拍控制方法。既解决了传统六拍控制策略中由于绕组电感所造成的电流滞后问题,又改善了由于换相所造成的电流脉动问题。该方法是通过在每两拍之间插入一小段缓冲区来实现的,该缓冲区使下一拍将要切入的电流提前切入,同时使当前拍将要切出的电流延迟切出。通过确定缓冲区的起始位置,即超前换相角的大小,保证每一拍所对应的相电流的中心和反电动势的中心重合。通过选取缓冲区开关器件PWM调制的占空比,降低电机运行过程中的换相转矩脉动。该文方法只需根据负载大小选取超前换相角,一旦选定适用于所有转速。文中给出了该方法的理论推导过程和实验验证波形,从实验结果可以发现,电流滞后被消除,换相电流脉动显著减小,电机的利用率得到提高。

A neural network-based commutation optimization strategy and drive system design for brushless DC motor

An optimized commutation method based on backpropagation(BP)neural network is proposed to resolve the low stability and high-power consumption caused by inaccurate commutation point prediction in conventional commutation strategy during acceleration and deceleration.This article also builds a complete brushless DC motor drive system based on the GD32F103 micro control unit(MCU),with an Artix-7 XC7A35T field programmable gate array(FPGA)to meet the performance requirements of neural network calculation for real-time motor commutation control.Experimental results show that the proposed optimization strategy can effectively improve the system stability during system acceleration and deceleration,and reduce the current spikes generated during speed chan-ges.The system power consumption is reduced by about 11.7%on average.

Six-step Voltage Control of PM Brushless AC Motors under High Speed Flux-weakening Operation for EV/HEV Applications

The torque-speed characteristics of brushless motor having an interior permanent magnet rotor and a sinusoidal back-emf waveform are compared experimentally when it is operated in brushless AC(BLAC) mode and brushless DC (BLDC) modes with both 2-phase,120° conduction(BLDC-120) and 3-phase,180° conduction(BLDC-180).Particular emphasis is on high-speed,six-step voltage controlled,flux-weakening operation.It is shown that for EV/HEV applications,even for interior PM brushless motors which have sinusoidal back-emf waveforms,in order to achieve maximum torque per ampere capability over wide operation speed range,it is advantageous to employ a hybrid operation mode-BLAC operation in the constant torque region and six-step voltage control(BLDC-180 operation,together with current phase control) in the flux-weakening region.

Analysis of torque-current characteristic of brushless DC motor driven by three-phase H-bridge

Presents the simulation and analysis of the steady state characteristic of a brushless DC motor studies the torque current characteristic of the motor as well and discusses the design of a current measure circuit for torque controlling.

Analysis of Torque Ripple of Permanent Magnet Brushless DC Motor

Torque tripple has significant effect on performance of permanent magnet brushless DC motor. This paper presents a mathematical model built for such a motor, the analysis of torque tripple for a brushless DC motor with sinusoidal flux distribution, which is verified by torque tripple experiments run with a test motor, and equations developed for torque tripple resulting from different sator current errors.

Design and implementation of a position sensorless control method for brushless DC motors

Because brushless direct current(BLDC) motors have the advantages of a compact size, high power density, high efficiency, and long operating life time, they are widely used in many industrial products and electric traction systems. It is known that the BLDC motors have no brushes for commutation. They are commutated with electronically commutation. So, the rotor position information of the BLDC motors must be known to understand which winding will be energized according to the energizing sequence. In most of the existing BLDC motor drivers, rotor position information is detected by Hall effect sensors. This kind of mechanical position sensors will bring additional connections and costs, reliability decrease and noise increase. In order to improve the control performance and extend the range of speed regulation for BLDC motors, a position sensorless control method is proposed in this paper. In the proposed control method, rotor position information of the BLDC motors is detected from the back electromagnetic forces(back-EMFs) which are estimated by an unknown-input observer with line to line currents and line to line voltages. For the purpose of verifying the effectiveness of the proposed control method, a model is built and simulated on the Matlab/Simulink platform. The simulation results show that the speed regulation performance of BLDC motors is improved compared with using Hall effect sensors. At the same time, the reliability of the BLDC motors is improved and the costs of them are reduced because the position sensor is eliminated.