ANovel Non-Isolated Cubic DC-DC Converter with High Voltage Gain for Renewable Energy Power Generation System

In recent years,switched inductor(SL)technology,switched capacitor(SC)technology,and switched inductor-capacitor(SL-SC)technology have been widely applied to optimize and improve DC-DC boost converters,which can effectively enhance voltage gain and reduce device stress.To address the issue of low output voltage in current renewable energy power generation systems,this study proposes a novel non-isolated cubic high-gain DC-DC converter based on the traditional quadratic DC-DC boost converter by incorporating a SC and a SL-SC unit.Firstly,the proposed converter’s details are elaborated,including its topology structure,operating mode,voltage gain,device stress,and power loss.Subsequently,a comparative analysis is conducted on the voltage gain and device stress between the proposed converter and other high-gain converters.Then,a closed-loop simulation system is constructed to obtain simulation waveforms of various devices and explore the dynamic performance.Finally,an experimental prototype is built,experimental waveforms are obtained,and the experimental dynamic performance and conversion efficiency are analyzed.The theoretical analysis’s correctness is verified through simulation and experimental results.The proposed converter has advantages such as high voltage gain,low device stress,high conversion efficiency,simple control,and wide input voltage range,achieving a good balance between voltage gain,device stress,and power loss.The proposed converter is well-suited for renewable energy systems and holds theoretical significance and practical value in renewable energy applications.It provides an effective solution to the issue of low output voltage in renewable energy power generation systems.

A Current-Mode DC-DC Buck Converter with High Stability and Fast Dynamic Response

A current-mode DC-DC buck converter with high stability is presented. The loop gain＇s expression of the current-mode converter is derived by employing an advanced model of a current-mode control converter. After analyzing the loop gain＇s expression, which illustrates the method of selecting suitable frequency compensation for the control loop,a novel pole-zero tracking frequency compensation is proposed. Based on theoretical analysis, a DC-DC buck converter with high stability is designed with 0.5μm-CMOS technology. The simulated results reveal that the stability of the converter is independent of the load current and the input voltage. Moreover,the converter provides a full load transient response setting time of less than 5μs and overshoots and undershoots of less than 30mV.

Modeling the System for Hybrid Renewable Energy Using Highly Efficient Converters and Generator

High-efficient isolated DC/DC converters with a high-efficiency synchronous reluctance generator(SRG)are the ultimate solutions in DC microgrid systems.The design and modeling of isolated DC/DC converters with the performance of SRG are carried out.On the generator side,reactive and active powers are used as pulse width modulation(PWM)control variables.Further,the flux estimator is used.Three-phase PWM rectifier is used by applying space vector modulation(SVM)with a constant switching frequency for direct power control.Further,the paper also includes the experimental validation of the results.The paper also proposes that highly efficient power converters and synchronous reluctance generators are required to achieve high performance for hybrid renewable energy systems applications.

A low noise high efficiency buck DC-DC converter with sigma-delta modulation

Some research efforts to improve the efficiency and noise performance of buck DC-DC converters are explored.A carefully designed power MOSFET driver,including a dead time controller,discontinuous current mode（DCM） controller and gate width controller,is proposed to improve efficiency.Instead of PWM modulation, sigma-delta modulation is introduced into the feedback loop of the converter to move out the clock-referred harmonic spike.The proposed converter has been designed and fabricated by a 0.35μm CMOS process.Measured results show that the peak efficiency of the converter can reach 93%and sigma-delta modulation suppresses the harmonic spike by 30 dB over PWM modulation.

DCM,FSM,dead time and width controllers for a high frequency high efficiency buck DC-DC converter over a wide load range

This paper presents a width controller,a dead time controller,a discontinuous current mode（DCM） controller and a frequency skipping modulation（FSM） controller for a high frequency high efficiency buck DC-DC converter. To improve the efficiency over a wide load range,especially at high switching frequency,the dead time controller and width controller are applied to enhance the high load efficiency,while the DCM controller and FSM controller are proposed to increase the light load efficiency.The proposed DC-DC converter controllers have been designed and fabricated in the Chartered 0.35μm CMOS process,and the measured results show that the efficiency of the buck DC-DC converter is above 80%over a wide load current range from 8 to 570 mA,and the peak efficiency is 86%at 10 MHz switching frequency.

Large-areaβ-Ga_(2)O_(3) Schottky barrier diode and its application in DC-DC converters

We demonstrate superb large-area verticalβ-Ga_(2)O_(3)SBDs with a Schottky contact area of 1×1 mm^(2)and obtain a high-efficiency DC-DC converter based on the device.Theβ-Ga_(2)O_(3)SBD can obtain a forward current of 8 A with a forward volt-age of 5 V,and has a reverse breakdown voltage of 612 V.The forward turn-on voltage(VF)and the on-resistance(Ron)are 1.17 V and 0.46Ω,respectively.The conversion efficiency of theβ-Ga_(2)O_(3)SBD-based DC-DC converter is 95.81%.This work indicates the great potential of Ga_(2)O_(3)SBDs and relevant circuits in power electronic applications.

Buck Converter Current Measurement Using Differential Amplifier

The accuracy of the measured current is a preeminent parameter for Current Control based Power Converter applications to ensure genuine operation of the designed converter.The current measurement accuracy can be affected by several parameters which includes the type of technology used,components used for the selected technology,aging,usage,operating and environmental conditions.The effect of gain resistors and their manufacturing tolerances on differential amplifier-based buck converter current measurement is investigated in this work.The analysis mainly focused on the output voltage variation and its accuracy with respect to the change in gain resistance tolerances.The gain resistors with 5%,1%,0.5%and 0.1%manufacturing tolerances taken for the worst-case analysis and the calculated performance results are compared and verified with the simula-tion results.The Operational amplifiers(Op-Amp)for high frequency power con-verter applications must operate in a high frequency noise environment and the intended current measuring system must manage common mode noise distur-bances paired with the signal to be measured.Based on the Common Mode Rejec-tion Ratio(CMRR)the common mode voltages and noise signals will effectively getfiltered out.Lesser CMRR results in lower common mode signal rejection,resulting in poor precision and noise rejection.In differential amplifiers,the CMRR predominantly depends on gain resistors.So,the variations in Common Mode Rejection Ratio due to gain resistor tolerances also analyzed and compared with the output voltage variations.Besides the effects of resistor tolerances,this paper also examines the effect of Op-Amp offset voltage on output accuracy spe-cifically for low magnitude input currents.The obtained results from this analysis clearly shows that the gain resistors with 0.1%tolerance gives maximum accuracy with improved CMRR and accuracy at low magnitude input currents will get well improved by using Op-Amps with Low Offset voltage specifications.

Design of Second Order Sliding Mode and Sliding Mode Algorithms:A Practical Insight to DC-DC Buck Converter

This paper presents a simple and systematic approach to design second order sliding mode controller for buck converters.The second order sliding mode control(SOSMC)based on twisting algorithm has been implemented to control buck switch mode converter.The idea behind this strategy is to suppress chattering and maintain robustness and finite time convergence properties of the output voltage error to the equilibrium point under the load variations and parametric uncertainties.In addition,the influence of the twisting algorithm on the performance of closed-loop system is investigated and compared with other algorithms of first order sliding mode control such as adaptive sliding mode control(ASMC),nonsingular terminal sliding mode control(NTSMC).In comparative evaluation,the transient response of the output voltage with the step change in the load and the start-up response of the output voltage with the step change in the input voltage of buck converter were compared.Experimental results were obtained from a hardware setup constructed in laboratory.Finally,for all of the surveyed control methods,the theoretical considerations,numerical simulations,and experimental measurements from a laboratory prototype are compared for different operating points.It is shown that the proposed twisting method presents an improvement in steady state error and settling time of output voltage during load changes.

Pole placement method of controlling chaos in DC-DC buck converters

Based on the mechanism for the generation of chaos in a buck converter, a pole placement method is proposed and applied to controlling the chaos in a circuit. The control circuit is designed and tested. Numerical calculation and circuit implementation demonstrate the validity of this chaos control method.

Study of Sliding Mode Control of DC-DC Buck Converter

In this paper, a robust sliding mode controller for the control of dc-dc buck converter is designed and analyzed. Dynamic equations describing the buck converter are derived and sliding mode controller is designed. A two-loop control is employed for a buck converter. The robustness of the sliding mode controlled buck converter system is tested for step load changes and input voltage variations. The theoretical predictions are validated by means of simulations. Matlab/Simulink is used for the simulations. The simulation results are presented. The buck converter is tested with operating point changes and parameter uncertainties. Fast dynamic response of the output voltage and robustness to load and input voltage variations are obtained.

Direct Model Predictive Control of Noninverting Buck-boost DC-DC Converter

In this paper, direct model predictive control(DMPC) of the noninverting buck-boost DC-DC converter with magnetic coupling between input and output is proposed. Unlike most of the other converters, the subject converter has the advantage of exhibiting minimum phase behavior in the boost mode. However, a major issue that arises in the classical control of the converter is the dead zone near the transition of the buck and boost mode. The reason for the dead zone is practically unrealizable duty cycles, which are close to zero or unity, of pulse width modulation(PWM) near the transition region. To overcome this issue, we propose to use DMPC. In DMPC, the switches are manipulated directly by the controller without the need of PWM.Thereby, avoiding the dead zone altogether. DMPC also offers several other advantages over classical techniques that include optimality and explicit current constraints. Simulations of the proposed DMPC technique on the converter show that the dead zone has been successfully avoided. Moreover, simulations show that the DMPC technique results in a significantly improved performance as compared to the classical control techniques in terms of response time, reference tracking, and overshoot.

A Piecewise Linear Slope Compensation Circuit for DC-DC Converters

To prevent sub-harmonic oscillation and improve the stability and load capacity of the system,a piecewise linear slope compensation circuit is designed. Compared with the traditional design, this circuit provides a compensation signal whose slope varies from different duty cycles at - 40-85℃ ,and reduces the negative effect of slope compensation on the system＇s load capacity and transient response. A current mode PWM Boost DC-DC converter employing this slope compensation circuit is implemented in a UMC 0.6μm-BCD process. The results indicate that the circuit works well and effectively,and the load capacity is increased by 20%. The chip area of the piecewise linear slope compensation circuit is 0.01mm^2 ,which consumes only 8μA quiescent current,and the efficiency ranges up to 93%.

SIMULATION STUDY OF CHAOS IN DC-DC CONVERTER

A DC DC buck converter c on trolled by naturally sampled, constant frequency PWM is considered. The existe nce of chaotic solutions and the output performance of the system under differen t circuit parameters are studied. The transforming pattern of system behavior fr om steady state to chaotic is discovered by the cascades of period doubling bi furcation and the cascades of periodic orbit in V I phase space. Accordingl y, it is validated that change of values of the circuit parameters may lead DC DC converter to chaotic motion. Performances of the output ripples fro m steady state to chaotic are analyzed in time and frequency domains respective ly. Some important conclusions are helpful for opt imization design of DC DC converter.

Improving Characteristics of Integrated Switched-Capacitor DC-DC Converter by CMOS Technology

An integrated 3.3V/1.2V SC DC-DC converter operating under 10MHz with a fixed duty radio of 0.5 is presented.To improve the output current of the converter,CMOS technology is adopted to fabricate the switching devices,and mutually compensatory circuitry technology is also employed to double the output current furthermore.The simulation results using Hspice simulation software,show that the output currents of a single unit circuit and two unit circuits connected in a mutually compensatory manner of the improved converter is about 12.5mA and 26mA,respectively.The power conversion efficiency of the mutually compensatory circuit can amount to 73%,while its output voltage ripple is less than 1.5%.The converter is fabricated in standard Rohm 0.35μm CMOS technology in Tokyo University of Japan.The test result indicates that the output current of 9.8mA can be obtained from a single unit circuit of the improved converter.

A Novel Hybrid DPWM for Digital DC-DC Converters

We present a new hybrid digital pulse-width modulator （DPWM） for digital DC-DC converters that employs a ring-oscillator/counter structure. Based on a temperature/process compensation technique and a novel digital controller, the proposed DPWM can not only offer temperature/process-independent pulse widths, but also operate at a much higher clock frequency than the existing delay-line/counter DPWM structure. Post-simulation results show that with our DPWM, the system clock frequency reaches 156.9MHz while the worst variation,in a temperature range of 0 to 100℃under all process corners,is only± 9.4%.

双频DC-DC变换器的磁集成技术

双频Buck变换器由两个降压单元级联构成,具有动态响应快,开关损耗小等优势。然而不足的是磁件占据了整个系统的大部分体积与重量,降低了系统的功率密度。针对这一问题,提出一种三段式绕制磁集成技术,将磁件以解耦的方式集成在一副磁心中。该文首先建立集成磁件的磁路等效模型,通过抵消各绕组之间的耦合作用推导出解耦条件,并详细阐述了磁心的选取、匝数以及气隙的设计原则。其次,利用有限元仿真平台对所提集成磁件进行建模分析,与现有的集成方法相比,磁通密度分布更为均匀,磁心的利用率得到了有效提升。最后,搭建一台48 V/12 V、108 W的实验样机,体积和重量同分离磁件相比降低了31.2%和25.3%,提高了系统的功率密度,验证了该集成方法理论分析的正确性和可行性。

三电平Buck变换器输出纹波电压畸变机理分析

交错控制三电平Buck变换器受功率开关器件寄生参数的影响,输出电压纹波及电感电流纹波不仅发生了畸变,且纹波电压大小和忽略寄生参数的纹波电压存在较大误差。因此,深入分析了交错控制三电平Buck变换器输出纹波电压畸变机理,建立了考虑功率开关器件寄生参数的电感电流纹波、输出纹波电压的数学模型。在此基础上进行了实验验证,实验结果表明,功率开关器件的寄生参数是导致输出纹波电压波形畸变以及与理想模型产生较大误差的主要原因,验证了理论分析的正确性。所得结论可为三电平Buck变换器的变换器参数设计提供理论指导。

带感性负载的Buck-Boost变换器的非线性行为分析及优化控制

Buck-Boost变换器在某些参数发生变化时会呈现出丰富的非线性行为,这些行为将严重影响系统的稳定性,使得系统输出的电能质量劣化。文章基于实际变换器的负载特性,深入研究了感性阻抗负载下Buck-Boost变换器的非线性行为产生机理,提出了一种对数延迟反馈控制方法。该方法选取系统的输出延迟值与自身的值作差形成反馈信号;将该信号通过比例环节、求和环节和对数环节形成控制信号,以负反馈的形式施加于系统;最后基于稳定判据确定最优控制参数并对系统实施控制。为验证该方法的有效性,进行了大量的仿真实验,结果表明该方法能很好地抑制系统的非线性行为,扩展其稳定边界,改善系统输出的电能质量。

宽增益高效率级联式四开关Buck-Boost LLC变换器

为了解决变频控制的桥臂共用型四开关Buck-BoostLLC级联变换器磁性元件设计和优化困难的问题,提出一种二次侧为特殊全桥整流结构的级联式四开关Buck-Boost LLC变换器。通过控制二次侧开关管的交叠导通时间以拓宽变换器的电压增益。该变换器可根据不同的输入电压范围工作在交叠模式和整流模式;在不改变变换器参数的条件下将增益显著提高,能够适应更宽范围的输入电压,同时保持了变换器较高的工作效率。在两种工作模式的基础上,采用移相控制使变换器所有开关管实现零电压导通(ZVS),二极管实现零电流关断(ZCS)。结合状态平面轨迹分析法,对定频控制的级联式四开关Buck-Boost LLC变换器进行模态分析,并推导两种工作模式下的输入-输出表达式和开关管的软开关实现条件。最后,通过研制一台70~280 V输入、240 W/28 V输出的实验样机,验证了理论分析的正确性。

高频双频Buck变换器平面集成磁件优化设计

针对目前开关器件和磁性元件性能不足导致双频Buck变换器的效率和功率密度低的问题,研究了一种高效高功率密度的双频Buck变换器。变换器将工作在连续导通(CCM)模式,采用解耦合的平面集成电感器完成系统磁元件的集成,结合磁件的集成方法、有限的PCB层数和变换器的特性给出双频Buck变换器的参数,然后,提出了一种双频Buck变换器平面磁件的设计方法,并完成系统磁元件的优化设计。最后,基于第3代半导体SiC器件以及平面集成磁件,设计了额定功率200 W、开关频率400 kHz的双频Buck变换器。结果表明:该变换器峰值效率将达到96.1%,功率密度为46.1 W/in^(3)(1 in=25.4 mm),验证了双频Buck变换器设计方法的正确性和有效性。