Experimental Investigation on Condensate Revaporization During Gas Injection Development in Fractured Gas Condensate Reservoirs

The gas field in the Bohai Bay Basin is a fractured metamorphic buried-hill reservoir with dual-media characteristics. The retrograde vaporization mechanism observed in this type of gas condensate reservoir differs significantly from that observed in sand gas condensate reservoirs. However, studies on improving the recovery of fractured gas condensate reservoirs are limited;thus, the impact of retrograde vaporization on condensate within fractured metamorphic buried-hill reservoirs remains unclear. To address this gap, a series of gas injection experiments are conducted in pressure-volume-temperature(PVT) cells and long-cores to investigate the retrograde vaporization effect of condensate using different gas injection media in fractured gas condensate reservoirs. We analyze the variation in condensate volume, gas-to-oil ratio, and condensate recovery during gas injection and examine the influence of various gas injection media(CO_(2), N_(2), and dry gas) under different reservoir properties and varying gas injection times. The results demonstrate that the exchange of components between injected gas and condensate significantly influences condensate retrograde vaporization in the formation. Compared with dry gas injection and N_(2) injection,CO_(2) injection exhibits a superior retrograde vaporization effect. At a CO_(2) injection volume of 1 PV, the percentage shrinkage volume of condensate is 13.82%. Additionally, at the maximum retrograde condensation pressure, CO_(2) injection can increase the recovery of condensate by 22.4%. However, the condensate recovery is notably lower in fractured gas condensate reservoirs than in homogeneous reservoirs, owing to the creation of dominant gas channeling by fractures, which leads to decreased condensate recovery. Regarding gas injection timing, the effect of gas injection at reservoir pressure on improving condensate recovery is superior to that of gas injection at the maximum retrograde condensation pressure. This research provides valuable guidance for designing gas injection development plans and dynamic tracking adjustments for fractured gas condensate reservoirs.

Mechanistic investigation of gas injection treatment in a continental shale gas condensate reservoir

Low thermal evolution degree of gas and connected fracture network are key features in the continental shale gas reservoirs.When the pressure decreases lower than the dew point pressure,gas condensate diminishes the mobility of subsurface fluid forms in the near well region,which further reduces the productivity and final recovery factor in addition to the low connected fracture network.This work is motivated to investigate the application of gas injection,proven to be a feasible technique in conventional/marine-shale gas condensate reservoirs,in continental shale gas condensate reservoirs.We apply a compositional model to investigate the mechanism of gas injection treatment taking a continental shale gas condensate reservoir in the Fuxing area,Sichuan Basin,China as an example.The results demonstrate that for the removal of gas condensate during CO_(2)injection,re-vaporization plays the main mechanism through two processes including pressurization and development of miscibility,while the former is overwhelming.Considering the variation trend of the total volume of gas condensate,we divide the whole injection process into four and six stages in the single fracture model and fracture network model,respectively,and reason the trend with respect to phase behavior and flow pattern.A sensitive study on the injected gas type indicates that the sorting of the gas injection performance to remove gas condensate produced gas followed by CH4,and followed by CO_(2).Finally,we investigate the performance of cyclic produced-gas injection and optimize the injection scheme.This work provides technical and theoretical support for the development of continental shale gas reservoirs.

A new model simulating the development of gas condensate reservoirs

A new simulation model for the development of gas condensate reservoirs is introduced based on the influence that phase change,non-Darcy flow,and capillary pressure have on the production of gas condensates.The model predicts well performance,including bottom-hole pressure,oil/gas production rate,oil/gas recovery,gaseoil ratio,and the change in produced fluid composition.It also calculates dynamic characters,such as the change of pressure field and oil/gas saturation field during the development of gas condensate reservoirs.The model is applicable to different boundary conditions(both constant-pressure and sealed boundary)and different production modes(both constant-pressure and constant-volume production modes).Model validation attempted using numerical simulation results for sealed boundary conditions with constant-pressure production mode has shown a relatively good match,proving its validity.For constant-pressure boundary conditions with constant-volume production mode,four stages are defined according to the dynamic behavior of production performance in the development of gas condensate reservoirs.

Phase Transitions and Seepage Characteristics during the Depletion Development of Deep Condensate Gas Reservoirs

Deep condensate gas reservoirs exhibit highly complex and variable phase behaviors,making it crucial to understand the relationship between fluid phase states and flow patterns.This study conducts a comprehensive analysis of the actual production process of the deep condensate gas well A1 in a certain oilfield in China.Combining phase behavior analysis and CMG software simulations,the study systematically investigates phase transitions,viscosity,and density changes in the gas and liquid phases under different pressure conditions,with a reservoir temperature of 165°C.The research covers three crucial depletion stages of the reservoir:single-phase flow,two-phase transition,and two-phase flow.The findings indicate that retrograde condensation occurs when the pressure falls below the dew point pressure,reachingmaximum condensate liquid production at around 25MPa.As pressure decreases,gas phase density and viscosity gradually decrease,while liquid phase density and viscosity show an increasing trend.In the initial single-phase flow stage,maintaining a consistent gas-oil ratio is observed when both bottom-hole and reservoir pressures are higher than the dew point pressure.However,a sudden drop in bottom-hole pressure below the dew point triggers the production of condensate oil,significantly reducing subsequent gas and oil production.In the transitional two-phase flow stage,as the bottom-hole pressure further decreases,the reservoir exhibits a complex flow regime with coexisting areas of gas and liquid.In the subsequent two-phase flow stage,when both bottom-hole and reservoir pressures are below the dew point pressure,a significant increase in the gas-oil ratio is observed.The reservoir manifests a two-phase flow regime,devoid of single-phase gas flow areas.For lowpressure conditions in deep condensate gas reservoirs,considerations include gas injection,gas lift,and cyclic gas injection and production in surrounding wells.Additionally,techniques such as hot nitrogen or CO_(2) injection can be employed to mitigate retrograde condensation damage.The implications of this study are crucial for developing targeted development strategies and enhancing the overall development of deep condensate gas reservoirs.

A transient production prediction method for tight condensate gas wells with multiphase flow

Considering the phase behaviors in condensate gas reservoirs and the oil-gas two-phase linear flow and boundary-dominated flow in the reservoir,a method for predicting the relationship between oil saturation and pressure in the full-path of tight condensate gas well is proposed,and a model for predicting the transient production from tight condensate gas wells with multiphase flow is established.The research indicates that the relationship curve between condensate oil saturation and pressure is crucial for calculating the pseudo-pressure.In the early stage of production or in areas far from the wellbore with high reservoir pressure,the condensate oil saturation can be calculated using early-stage production dynamic data through material balance models.In the late stage of production or in areas close to the wellbore with low reservoir pressure,the condensate oil saturation can be calculated using the data of constant composition expansion test.In the middle stages of production or when reservoir pressure is at an intermediate level,the data obtained from the previous two stages can be interpolated to form a complete full-path relationship curve between oil saturation and pressure.Through simulation and field application,the new method is verified to be reliable and practical.It can be applied for prediction of middle-stage and late-stage production of tight condensate gas wells and assessment of single-well recoverable reserves.

Numerical Simulation of Oil and Gas Two-Phase Flow in Deep Condensate Gas Reservoirs in Bohai Buried Hills

The BZ19-6 gas field is characterized by high temperature and high pressure (HTHP), high condensate content, little difference between the formation pressure and dew point pressure, and large amount of reverse condensate liquid. During the early stage of depletion development, the production gas-oil ratio (GOR) and production capacity remain relatively stable, which is inconsistent with the conventional reverse condensate seepage law. In view of the static and dynamic conflict in development and production, indoor high-temperature and high-pressure PVT experiment was carried out to reveal the mist-like condensation phenomenon of fluids in the BZ19-6 formation. And the seepage characteristics of condensate gas reservoirs with various degrees of depletion under the condition of HTHP were analyzed based on production performance. The change rule of fluid phase state was analyzed in response to the characterization difficulties of the seepage mechanism. The fluid state was described using the miscible mechanism. And the interphase permeability interpolation coefficient was introduced based on interfacial tension. By doing so, the accurate characterization of the “single-phase flow of condensate gas-near-miscible mist-like quasi single-phase flow-oil-gas two-phase flow” during the development process was achieved. Then the accurate fitting of key indicators for oilfield development was completed, and the distribution law of formation pressure and the law of condensate oil precipitation under different reservoir conditions are obtained. Based on research results, the regulation strategy of variable flow rate production was developed. Currently, the work system has been optimized for 11 wells, achieving a “zero increase” in the GOS of the gas field and an annual oil increase of 22,000 cubic meters.

Enhancing recovery and sensitivity studies in an unconventional tight gas condensate reservoir

The recovery factor from tight gas reservoirs is typically less than 15%, even with multistage hydrauhc tractunng stimulation. Such low recovery is exacerbated in tight gas condensate reservoirs, where the depletion of gas leaves the valuable condensate behind. In this paper, three enhanced gas recovery （EGR） methods including produced gas injection, CO2 injection and water injection are investigated to increase the well productivity for a tight gas condensate reservoir in the Montney Formation, Canada. The production performance of the three EGR methods is compared and their economic feasibility is evaluated. Sensitivity analysis of the key factors such as primary production duration, bottom-hole pressures, and fracture conductivity is conducted and their effects on the well production performance are analyzed. Results show that, compared with the simple depletion method, both the cumulative gas and condensate production increase with fluids injected. Produced gas injection leads to both a higher gas and condensate production compared with those of the CO2 injection, while waterflooding suffers from injection difficulty and the corresponding low sweep efficiency. Meanwhile, the injection cost is lower for the produced gas injection due to the on-site available gas source and minimal transport costs, gaining more economic benefits than the other EGR methods.

Change of phase state during multi-cycle injection and production process of condensate gas reservoir based underground gas storage

Based on the differences in production mode and operation process between gas storage and gas reservoir,we established a phase balance test procedure and a theoretical simulation model of phase balance during multi-cycles of injection and production of underground gas storage(UGS)rebuilt from condensate gas reservoir to study the phase characteristics of produced and remaining fluids during multi-cycles of injection and production.Take condensate reservoir gas storage as example,the composition of produced fluid and remaining fluid,phase state of remaining fluid,retrograde condensate saturation and condensate recovery degree in the process of multi-cycles of injection-production were studied through multi-cycle injection-production experiment and phase equilibrium theory simulation.The injected gas could greatly improve the recovery of condensate oil in the gas reservoir,and the condensate oil recovery increased by 42% after 5 cycles of injection and production;the injected gas had significant evaporative and extraction effects on the condensate,especially during the first two cycles;the condensate oil saturation of the formation decreased with the increase of injection-production cycles,and the condensate oil saturation after multi-cycles of injection-production was almost 0;the storage capacity increased by about 7.5% after multi-cycles of injection and production,and the cumulative gas injection volume in the 5 th cycle increased by about 25%compared with that in the 1 st cycle.

Deliverability of wells in carbonate gas condensate reservoirs and the capillary number effect

With the development of the Tazhong No. 1 carbonate gas condensate reservoir in China, it has become more and more important to study the characteristics of gas condensate well deliverability. A single-well radial simulator for dual-permeability reservoirs was established to study the influences of fluid properties, permeability, and pressure drawdown on well deliverability with and without the capillary number effect. The simulation shows that well deliverability basically maintains its initial value and is not affected by the capillary number when the formation pressure is higher than dew-point pressure. However, well deliverability drops rapidly when the formation pressure is lower than dew-point pressure. Even if the condensate dropout is very low, well deliverability without the capillary number effect reduces to 50 percent of its initial value when reservoir pressure declines to 95 percent of dew-point pressure, but well deliverability is significantly improved if the capillary number effect exists. The capillary number effect is most significant when reservoir pressure is just lower than dew point pressure, then the effect decreases; the reduction of well deliverability is mainly caused by the reduction of gas relative permeability of the matrix system near the wellbore.

Gas condensate reservoirs: Characterization and calculation of dew-point pressure

A large data bank of more than 700 gas-condensate samples collected from literature and experiments was established.On this basis,empirical correlations and equations of state commonly used to calculate dew-point pressure(DPP)were evaluated.A new model for estimating DPP was proposed.All the empirical correlations and the Peng-Robinson state equation were compared,and sensitivity of parameters was analyzed.The current standards used to identify gas condensate were evaluated and found to be not accurate enough.The Peng-Robinson state equation has no unique solution and is affected by multiple factors such as the characterization of C7+components and the splitting scheme.The Nemeth-Kennedy correlation has the highest accuracy when applied to the data bank established in this study,followed by Elsharkawy correlation and Godwin correlation.While Shokir correlation cannot be used for samples without C7+components,it is therefore the lowest in accuracy.The newly proposed model has an average absolute error,root mean square error and coefficient of determination of 7.5%,588,and 0.87,respectively,and is better than the above four correlations statistically.The proposed model proved to be more accurate and valid when compared to experimental results and simulation with the Peng-Robinson state equation.

Development an Easy-to-Use Simulator to Thermodynamic Design of Gas Condensate Reservoir’s Separators

Separator design in petroleum engineering is so important because of its important role in the evaluation of optimum parameters and also to achieve to maximum stock tank liquid. However, no simulator exists that simultaneously and directly optimizes the parameters “pressure”, “temperature”, and so on. On the other hands, Commercial simulators fix one parameter and vary another parameter to achieve the optimum conditions. So, they need long-time simulation. Moreover, gas condensate reservoirs, like another reservoirs, have this problem as well. In present paper, a self-developed simulator applied in the optimized design of gas condensate reservoir’s separators by determining optimized pressure, temperature, and number of separators in order to obtain maximized tank liquid volume and minimized tank liquid density utilizing Matlab software and other commercial simulators such as Aspen-Plus, Aspen-Hysys, and PVTi to do a comparison. Also, each software was separately tested with one, two, and three separators to obtain the optimum number of separators. Additionally, Peng-Robinson equation of state (PR EOS) has been applied in the simulation. For simulation input, a set of field data of gas condensate reservoir has been utilized, as well. The results show a good compatibility of this simulator with other simulators but in so little runtime (this simulator calculates the optimum pressure and temperature in a wide range of pressures and temperatures with the help of a simultaneous optimization algorithm in one stage) and the highest stock tank liquid is calculated with this simulator in comparison to other simulators. Also, with the help of this simulator, we are able to obtain the optimum pressure, temperature, and the number of separators in the gas condensate reservoir’s separators with any desired properties. Finally, this simulator optimizes the temperatures for each separator and obtains very good results despite the other simulators that fix temperatures for all separators in most times.

A New Method for the Dynamic Reserves of Gas Condensate Reservoir Using Cyclic Gas Injection Based on the Effects of Reinjection Ratio and Water Influx

As we all know, cyclic gas injection is one of the most effective development methods to improve condensate oil recovery. When dealing with the calculation of the reserves, the injection-production differences and water influx create great influence on the accuracy. Based on the existing research, we proposed a new material balance equation which considered the differences of composition between produced and injected fluids and the effect of water influx, and a solution was provided in this paper. The results of the method are closer to the actual situation because they are built on the law of conservation of mass, and the using of curve fitting method can not only avoid the use of water influx coefficient but also obtain the water influx rate and reserves at the same time. The YH-23 gas condensate reservoir is taking as a typical subject to do the research, which has been exploited by cycle gas injection for 14 years. Three different methods are used to calculate the reserves, and the results show that the method proposed in this paper has minimum error of 2.96%.

Economic Evaluation of Hydraulic Fracturing in a Gas Condensate Reservoir Operating below Dewpoint

Hydraulic fracturing is among the approaches used to optimize production from a gas condensate reservoir. A detailed economic analysis is required to evaluate the profitability and feasibility of hydraulic fracturing as an optimization option in a gas condensate reservoir operating below dewpoint. The objective of this research is to evaluate the economic benefits derivable from the use of hydraulic fracturing to improve gas and liquid recovery from a gas condensate reservoir operating below dewpoint. This research considers the use of four profit indicators to ascertain the profitability of hydraulic fracturing in a gas condensate reservoir operating below dewpoint by increasing the fracture halflength, fracture width and fracture permeability. The production data of the reservoir was obtained and the economic calculations done on excel spreadsheet and plots generated. The four profit indicators considered in the research are Net Present Value, Payout, Discounted Cash Flow Rate of Return and Profit per Dollar Invested. The economic justification was done by carrying out a comparative economic analysis from the result obtained when the reservoir of study was unfractured with that obtained when the reservoir was fractured at various fracture parameters. The economic analysis was done considering a royalty and tax rate of 18.5% and 30% respectively and a gas price of $2/MSCF and condensate price of $30/bbl. This is done so as to find out if the additional cost of hydraulic fracturing can be offset by the recovery from the reservoir when its pressure declined below dewpoint. The result obtained showed that the additional recovery due to hydraulic fracturing by increasing the fracture halflength, fracture width and fracture permeability was not enough to justify the application of hydraulic fracturing when the reservoir pressure declined below dewpoint.

Formation conditions and accumulation characteristics of Bozhong 19-6 large condensate gas field in offshore Bohai Bay Basin

Based on the study of natural gas resource, low buried hill trap formation mechanism, high quality reservoir control factors and natural gas preservation conditions, the formation conditions and reservoir accumulation characteristics of Bozhong 19-6 large condensate gas field were summarized. Large gas generation potential of multiple sets of thick humic-sapropelic source rocks in high maturity stage in Bozhong depression was the basis of large gas field formation. The multi-stage tectonic evolution since Indosinian period formed large-scale buried hill traps. The Tanlu fault activity formed multi-type reservoirs, and buried hill metamorphic rock of Archean and sand-conglomerate of Kongdian Formation were high-quality reservoirs. Thick overpressure lacustrine mudstone and weak neotectonic movement provided good preservation conditions. Bozhong 19-6 gas reservoir was a condensate gas reservoir with very high condensate oil content, and the gas origin was humic-sapropelic and kerogen-cracking gas, and the gas field had large gas thickness, high gas column characteristics and the accumulation process was first oil and then gas. The buried hill reservoir was a massive reservoir and the Kongdian reservoir was a stratified reservoir. The gas field had multi-channel hydrocarbon intense charge from overpressure source rocks, atmospheric-weak overpressure reservoir favorable for accumulation, thick overpressure mudstone caprock favorable for preservation, and natural gas ultra-late rapid accumulation model.

Hydrocarbon Charging and Accumulation Process of the Large Bozhong19-6 Condensate Gas Reservoirs in the Southwestern Bozhong Sub-Basin,Bohai Bay Basin,China

The Bozhong19-6(BZ19-6)condensate gas reservoirs,located in the southwestern Bozhong sub-basin,Bohai Bay Basin,China,were paleo-oil reservoirs in the geological past and have undergone at least three successive hydrocarbon charging events.The hydrocarbon migration and accumulation process of“early oil and late gas”has occurred in the current reservoirs.At the end of the sedimentation of the Guantao Formation(N_(1)g,∼12 Ma),the reservoirs began to fill with first stage low-moderate mature crude oil.At the late stage of the Lower Minghuazhen Formation(N_(1)ml)(∼6.7 Ma),the reservoirs were largely charged with second stage high mature crude oil.Since the deposition of the upper Minghuazhen Formation(N_(2)m^(u),∼5.1 Ma),the paleo-oil reservoirs were transformed into shallow Neogene reservoirs due to the reactivation of basement faults.From the late stage of the N_(2)m^(u)to the present day(∼2.8–0 Ma),the reservoirs were rapidly filled by natural gas within a short period.In addition,analysis of the formation of the reservoir bitumen and the conspicuous loss of the lower molecular weight n-alkanes in the crude oil reveal that the injection of a large amount of gas in the late stage caused gas flushing of the early charged oil.

Experimental and modeling study of CO_(2)-Improved gas recovery in gas condensate reservoir

This paper presents the effectiveness of the CO_(2) injection process at different periods during gascondensate reservoir development.Taking a real gas-condensate reservoir located in China's east region as an example,first,we conducted experiments of constant composition expansion(CCE),constant volume depletion(CVD),saturation pressure determination,and single flash.Next,a series of water/CO2 flooding experiments were been investigated,including water flooding at present pressure 15 MPa,CO_(2) flooding at 25.53 MPa,15 MPa,which repents initial pressure and present pressure respectively.Finally,the core flooding numerical model was constructed using a generalized equation-of-state model reservoir simulator(GEM)to reveal miscible flooding mechanism and the seepage flow characteristics in the condensate gas reservoir with CO2 injection.A desirable agreement achieved in experimental results and predicted pressure volume temperature(PVT)properties by the modified equation of state(EOS)in the CVD and CCE tests indicated that the proposed recombination method can successfully produce a fluid with the same phase behavior of initial reservoir fluid with an acceptable accuracy.The modeling results confirm the experimental results,and both methods indicate that significant productivity loss can occur in retrograde gas condensate reservoirs when the flowing bottom-hole pressure falls below dew point pressure.Moreover,the results show that CO_(2) treatment can improve gas productivity by a factor of about 1.39 compared with the water flooding mode.These results may help reservoir engineers and specialists to restore the lost productivity of gas condensate.

Origins and Differences in Condensate Gas Reservoirs between East and West of Tazhong Uplift in the Ordovician Tarim Basin, NW China

The Ordovician of the Tazhong area in the Tarim Basin has suffered multi-cyclic hydrocarbon charging, making Tazhong a typical condensate gas district. In this paper, production and test data were gathered and a detailed comparison was conducted on the geology and the fluid distribution and characteristics between the eastern and western Tazhong area. Eastern and western regions exhibit significant differences in tectonic structure, fluid distribution, and physical-chemical properties of oil and gas. Compared with the eastern region, the western part has a greater development of discordogenic gas associated with strike-slip faults which, combined with the Tazhong No. 1 fault zone, control the fluid distribution. The eastern region is mainly controlled by the Tazhong No. 1 fault zone. Fluid have markedly homogeneous properties in the east, but are heterogeneous in the west. The origins of oil and gas are different between the east and the west. In the east, hydrocarbons are mainly from Ordovician source rocks and natural gas is mostly derived from kerogen pyrolysis. In the west, the hydrocarbons mainly originated from Cambrian source rocks, and the gas was mostly generated by crude oil cracking. In sum, the east region is dominated by primary condensate gas reservoirs, and the western region is dominated by secondary condensate gas reservoirs. Because of the different geological settings and fluid physical properties, differences in the condensate gas reservoirs in the eastern and the western Tazhong area have been analyzed, and appropriate formation mechanisms for condensate gas origins are established.

Developing a K-value equation for predict dew point pressure of gas condensate reservoirs at high pressure

This paper proposed a new empirical K-value equation is developed to calculate dew pressure for gas condensate reservoirs.This equation is applicable in the wide ranges of composition,temperature,and pressure by considering the effect of composition via two equations for normal boiling point and critical temperature of the mixture.The range of dew pressure,temperature,heptane plus mole fraction,methane mole fraction,N2 mole fraction,CO2 mole fraction,and H2S mole fraction are fallen into 2666.7e9655 Psia,40e350.87
F,0.0021e0.213,0.3344e0.9668,0e0.4322,0e0.0864,and 0e0.942 respectively.As an important point,the proposed equation has any adjustable parameters,in addition,this equation indicates that in order to predict of dew pressure of gas condensate reservoirs,trial and error was not needed and therefore,computational speed increases beyond the accuracy.Moreover,the accuracy is validated by comparing against the experimental data of 81 gas condensate reservoirs samples from published literature and the results of Wilson,Whitson,and Ghafoori equations.Compared to the experimental data,the absolute average deviations of dew pressure calculations for the proposed equation,Wilson,Whitson,and Ghafoori were 7.6%,97.6%,99.4%,and 94.9%respectively.

Rheological property of low-damage,ideal packing,film-forming amphoteric/sulfonation polymer drilling fluids

Low-permeability dense reservoirs,including micro-fractured reservoirs,are commonly characterized by high content of clay substances,high original water saturation,high sensitivity to invasive fluids,high capillary pressure,complicated structure and anisotropic,high flow-resistance and micro pore throats etc,.Generally they also have lots of natural micro fractures,probably leading to stress sensibility.Main damaging factors in such reservoirs are water-sensibility and water-blocking caused by invasive fluids during drilling and production operations.Once damaged,formation permeability can rarely recovered.Numerous studies have shown that damaging extent of water-blocking ranges from 70% to 90%.Main damaging mechanisms and influencing factors of water-blocking were systematically analyzed.Also some feasible precaution or treating approaches of water-blocking were put forward.In a laboratory setting,a new multi-functional drilling fluid composed mainly of amphion polymer,sulfonation polymer,high effectively preventive water-blocking surfactants,ideal packing temporary bridging agents(TBA) and film-forming agents,etc.,were developed.New low-damage drilling fluids has many advantages,such as good rheological properties,excellent effectiveness of water-blocking prevention,good temporary plugging effect,low filtration and ultra-low permeability(API filtration≤5 mL,HTHP filtration≤10 mL,mud cake frictional coefficient≤0.14,permeability recovery>81%),can efficiently prevent or minimize damage,preserve natural formation and enhance comprehensive development-investment effect in TUHA Jurassic dense sandstone reservoir formation with low-permeability,the only one developing integrated condense gas field.Some references can be provided to similar reservoir formations.