Improvement of Microstructure and Mechanical Properties of Rapid Cooling Friction Stir-welded A1050 Pure Aluminum

Two-mm thick A1050 pure aluminum plates were successfully joined by conventional and rapid cooling friction stir welding(FSW), respectively. The microstructure and mechanical properties of the welded joints were investigated by electron backscatter diffraction characterization, Vickers hardness measurements, and tensile testing. The results showed that liquid CO_(2) coolant significantly reduced the peak temperature and increased the cooling rate, so the rapidly cooled FSW joint exhibited fine grains with a large number of dislocations. The grain refinement mechanism of the FSW A1050 pure aluminum joint was primarily attributed to the combined effects of continuous dynamic recrystallization, grain subdivision, and geometric dynamic recrystallization. Compared with conventional FSW, the yield strength, ultimate tensile strength, and fracture elongation of rapidly cooled FSW joint were significantly enhanced, and the welding efficiency was increased from 80% to 93%. The enhanced mechanical properties and improved synergy of strength and ductility were obtained due to the increased dislocation density and remarkable grain refinement. The wear of the tool can produce several WC particles retained in the joint, and the contribution of second phase strengthening to the enhanced strength should not be ignored.

Microstructure homogeneity and mechanical properties of laser-arc hybrid welded AZ31B magnesium alloy

Laser-arc hybrid welding of AZ31B magnesium alloy was carried out,the effects of welding parameters on weld formation,microstructure homogeneity and mechanical properties were investigated.The results showed that laser-arc hybrid welding was beneficial to improve the weld formation of magnesium alloy by inhibiting the defect of undercut and pores.The weld microstructure was mainly columnar grains neighboring the fusion line and equiaxed grains at the weld center.It was interesting that the grain size at the upper arc zone was smaller than that at the lower laser zone,with the difference mainly affected by laser power rather than welding current and welding speed.The welding parameters were optimized as laser power of 3.5 kW,welding current of 100 A and welding speed of 1.5 m/min.In this case,the weld was free of undercut and pores,and the tensile strength and elongation rate reached 252 MPa and 11.2%,respectively.Finally,the microstructure homogeneity was illustrated according to the heat distribution,and the evolution law of tensile properties was discussed basing on the weld formation and microstructure characteristics.

Beam oscillating parameters on pore inhibition,recrystallization and grain boundary characteristics of laser-arc hybrid welded AZ31 magnesium alloy

Oscillating laser-arc hybrid welding of AZ31B magnesium alloy was carried out,the effects of beam oscillation parameters on pore inhibition,microstructure,grain boundary characteristics and tensile properties were investigated.The results showed that the pore formation can be inhibited with oscillating frequency higher than 75 Hz and radius smaller than 0.5 mm.The columnar grains neighboring the fusion line can be broken by the beam oscillation behavior,while the grain growth was promoted with the increase of frequency or radius.It should be noted that the coincidence site lattice(CSL)boundaries were mainlyΣ13b andΣ29 boundaries,which were contributed by{10■2}tensile twins and{11■2}compression twins,respectively.The total fraction of CSL boundaries reached maximum at radius of 0.25 mm and frequency of 75 Hz,which was also confirmed as the optimized parameters.In this case,the elongation rate increased up to 13.2%,12.8%higher than that of the weld without beam oscillation.Finally,the pore formation and inhibition mechanisms were illustrated according to the state of melt flow and keyhole formation,the abnormal growth was discussed basing on secondary recrystallization,and the relationship among the pore formation,grain size,boundary characteristics and weld toughness were finally established.

Numerical Simulation Analysis of Welded Joints in Arch Ribs of Large Span Steel Pipe Arch Bridges

In order to study the residual stress distribution law of welded joints of arch ribs of large-span steel pipe concrete arch bridges,numerical simulation of temperature,stress and strain fields based on ABAQUS for welded joints of arch-ribbed steel tubes using 7-,8-and 9-layer welds is carried out and its accuracy is demonstrated.The steel pipe welding temperature changes,residual stress distribution,different processes residual stress changes in the law,the prediction of post-weld residual stress distribution and deformation are studied in this paper.The results show that the temperature field values and test results are more consistent with the accuracy of numerical simulation of welding,the welding process is mainly in the form of heat transfer;Residual high stresses are predominantly distributed in the Fusion zone(FZ)and Heat-affected zone(HAZ),with residual stress levels tending to decrease from the center of the weld along the axial path,the maximum stress appears in the FZ and HAZ junction;The number of welding layers has an effect on the residual stress distribution,the number of welding layers increases,the residual stress tends to decrease,while the FZ and HAZ high stress area range shrinks;Increasing the number of plies will increase the amount of residual distortion.

High temperature tensile properties of laser butt-welded plate of Inconel 718 superalloy with ultra-fine grains

For successfully forming multi-sheet cylinder sandwich structure of Inconel 718 superalloy, high temperature tensile properties of laser butt-welded plate of Inconel 718 superalloy were studied. The experiment results show that tensile direction has great effect on elongation of the laser butt-welded plate. Under conditions of transverse direction tension, the maximum elongation reaches 458.56% at 950 °C with strain rate of 3.1-10-4 s-1, in which the strain rate sensitivity value m is 0.352 and the welding seam is not deformed. Under conditions of longitudinal direction tension, the maximum elongation is 178.96% at 965 °C with strain rate of 6.2-10-4 s-1, in which m-value is 0.261, and the welding seam contributes to the deformation with the matrix. The microstructure in as-welded fusion zone is constituted of austenite dendrites and Laves phase precipitated in interdendrites. After longitudinal direction tension, a mixed microstructure with dendrite and equiaxed crystal appears in the welding seam due to dynamic recrystallization. After high temperature deforming, many δ-phase grains are transformed from Laves phase grains but a small part of residual Laves phase grains still exist in the welding seam. The deformation result of multi-sheet cylinder sandwich structure verifies that high temperature plasticity of the laser butt-welded plate can meet the requirement of superplastic forming.

Research on microstructure and properties of boron/Q235 steel laser welded dissimilar joints under synchronous thermal field

The mechanical mismatch effect frequently occurs in the dissimilar materials welded joints, thus leading to plastic gradient at the interface between the weld and heat-affected zone(HAZ). In this work, the boron steel and Q235 steel were selected for laser tailor welding,which obtained boron/Q235 steel tailor-welded blanks(TWBs). The method of welding with synchronous thermal field(WSTF) was utilized to eliminate the mismatch effects in TWBs. The WSTF was employed to adjust cooling rates of welded joints, thereby intervening in the solidification behaviors and phase transition of the molten pool. Boron/Q235 steel was welded by laser under conventional and WSTF(300-600 ℃) conditions, respectively. The results show that the microstructure of weld and HAZ(boron) was adequately transitioned to ferrites and pearlites instead of abundant martensite by WSTF. Meanwhile, the discrepancy of microhardness and yield strength between various regions of welded joints was greatly reduced, and the overall plasticity of welded joints was enhanced by WSTF. It is indicated that WSTF can effectively contribute to reducing plastic gradient and achieving mechanical congruity in welded joints by restraining the generation of hardbrittle phase, which could significantly improve the formability of TWBs in subsequent hot stamping.

基于SYSWELD的等高齿弧锥齿轮铣刀盘多层焊接数值模拟

本文借助Visual-Environment焊接模拟仿真软件,以SYSWELD为求解器对等高齿弧锥齿轮铣刀盘V形坡口多层焊接的焊接温度场进行数值模拟,得到了焊接温度场分布云图,分析并对比了每层焊缝中心、焊趾及距焊缝中心5mm处的温度循环曲线,推导出三层焊接温度场公式用于计算验证。结果表明,熔池中心温度最高,距离焊缝中心越近,温度梯度变化越大。

A Review of the Advances Made in Improving the Durability of Welded Wood against Water in Light of the Results of African Tropical Woods Welding

Wood plays a major role in the production of furniture and wooden structures.Nevertheless,in this process,the massive use of adhesives and plural connectors remains a definite problem for health and the environment.Therefore,wood welding is a breakthrough in this respect.This paper reviews the applications of wood welding in furniture and construction and then examines advances in improving the durability of welded wood against water.Our contribution also highlights the need to join African tropical woods using the rotational friction welding technique.According to our results,these woods present interesting chemical singularities,which could provide solutions to the water vulnerability of the welded wood.Moreover,the use of such a joining method would first free the Cameroonian furniture industry from the chemical industry,secondly position it at the forefront of new eco-design trends and thirdly make it competitive with other countries in the Central African sub-region.These works enrich the long and rich bibliography on the technique of wood welding,which has long been conspicuous by its absence of tropical woods.

Fatigue life analysis of SMA490BW steel welded butt joint for train bogie based on ABAQUS/FE-SAFE

Stress concentration has a significant effect on fatigue properties of welded butt joint of bogie.The influences of joint geometric parameters {weld edge transition arc radius r,weld toe inclination angle θ） on stress concentration coefficient Kt at weld toe and fatigue life N were studied based on the finite element software ABAQUS/FE-SAFE,and the parametric equations were founded based on regression analysis of Origin software.The results show that weld edge transition arc radius r plays the most important role in stress concentration coefficient Kt as well as weld toe inclination angle 0.For the same inclination angle θ,stress concentration coefficient Kt decreases gradually with transition arc radius r increasing.With inclination angle θ increases,the effect of transition arc radius r on stress concentration factor Kt is increasing continuously,also the effect of change in stress concentration coefficient Kt caused by r on fatigue life N is increasing continuously.While in the case of same weld edge transition arc radius r,stress concentration coefficient Kt increases with inclination angle θincreasing.With transition arc radius r increases,the effect of inclination angle θ on stress concentration factor Kt is decreasing constantly,the effect of change in stress concentration coefficient Kt caused by θ on fatigue life N is decreasing constantly.The associated parametric equations have important instructive significance for the improvement of stress concentration degree and fatigue life of welded butt joint for train bogie.

An innovative joint interface design for reducing intermetallic compounds and improving joint strength of thick plate friction stir welded Al/Mg joints

Friction stir welding of dissimilar Al/Mg thick plates still faces severe challenges, such as poor formability, formation of thick intermetallic compounds, and low joint strength. In this work, two joint configurations, namely inclined butt(conventional butt) and serrated interlocking(innovative butt), are proposed for improving weld formation and joint quality. The results show that a continuous and straight intermetallic compound layer appears at the Mg side interface in conventional butt joint, and the maximum average thickness reaches about 60.1 μm.Additionally, the Mg side interface also partially melts, forming a eutectic structure composed of Mg solid solution and Al_(12)Mg_(17) phase.For the innovative butt joint, the Mg side interface presents the curved interlocking feature, and intermetallic compounds can be reduced to less than 10 μm. The joint strength of innovative butt joint is more than three times that of conventional butt joint. This is due to the interlocking effect and thin intermetallic compounds in the innovative joint.

Study on microstructures and properties of preheated flash butt welded SW400 steel joints

Under the spirit of sustainable development, ‘lightweight’ has been gradually included into the vehicle design criterion by many manufacturers and used in automobile production. Following this trend, domestic wheel suppliers also begin to study the technology of lightweight wheel. One way to achieve this goal is improving strength grade of the steel and optimizing the structure design in the field of steel wheels. But there are a few problems in flash butt welding process in the application of high strength steel, leading to high rejection rates. SW400 steel is a special high strength wheel steel developed by Benxi Steel. Taking SW400 steel as the research material, this article studys the feasibility of improving the properties of rim flash butt welded joints by adding preheating process.

Influence of FSW parameters on formation quality and mechanical properties of Al 2024-T351 butt welded joints

The influence of R/v ratio on joint quality in 2024-T351 aluminum alloy was studied. Specimens were subjected to friction stir welding with the rotation rates of 750, 950 and 1180 r/min and welding speed between 73 and 190 mm/min, providing R/v ratio between 5.00 and 10.27. The welded joints were tested by means of both non-destructive （visual, penetrant and X-ray inspection） and destructive （metallographic, tension and hardness） testing. In all specimens typical zones are revealed, with corresponding differences in grain size. Tensile efficiency of the joints obtained is in the range of 52.2%to 82.3%. The results show that the best quality is obtained at R/v ratio of 8.06, 10.17 and 10.27. This behavior is attributed to the assumption that the material flows around the pin with an optimal speed, i.e. sufficient amount of material is available to fill the gap and prevent tunnel formation. R/v ratio also showed influence on hardness distribution, onion features and crack initiation/propagation zones.

Fatigue life evaluation of girth butt weld within welded cast steel joints based on the extrapolation notch stress method

The fatigue life evaluation of the girth butt weld within the welded cast steel joint was studied based on the extrapolation notch stress method.Firstly,the mesh sensitivity of the finite element model of the welded cast steel joint was analyzed to determine the optimal mesh size.Based on the stress field analysis of the finite element model of the welded cast steel joint at the weld toe and weld root,the sharp model of the extrapolation notch stress method was applied to derive the effective notch stress of the rounded model belonging to the effective notch stress method,in which the key problem is to calculate the extrapolation point C,and the extrapolation point C has an exponential function relationship with the geometric parameters of the welded cast steel joint.By setting different values of geometric parameters,the corresponding value of parameter C is calculated,and then the functional relationship between the extrapolation point C and the geometric parameters can be obtained by the multiple linear regression analysis.Meanwhile,the fatigue life evaluation of the girth butt weld within welded cast steel joints based on the effective notch stress was performed according to the guideline recommended by the IIW(International Institute of Welding).The results indicate that the extrapolation notch stress method can effectively simplify the process of calculating the effective notch stress and accurately evaluate the fatigue life of the girth butt weld within welded cast steel joints.

Experimental investigation on tensile strength of butt welded joint post high temperatures

In order to investigate the laws of variation on tensile strength of butt welded joint post high temperatures, the wide plate tension tests for butt welded joint were conducted after cooling down from different high temperatures. The tests indicate that specimens appear ductile fracture at the steel plate during the tension tests after cooling down. The maximum temperatures undergone and the cooling pattern are major factors influencing tensile strength of butt welded joint post high temperatures. The tensile strength mostly reduces by 8% within 900℃. Based on the experimental results, the paper proposes the calculation formulas of tensile strength of butt welded joint post high temperatures. The conclusions of the paper supply references for evaluation damage and reinforcement of steel structure post fire.

Fatigue properties of friction stir welded butt joint and base metal of MB8 magnesium alloy

The fatigue properties of friction stir welded （FSW） butt joint and base metal of MB8 magnesium alloy were investigated. The comparative fatigue tests were carried out using EHF-EM2OOK2-070-IA fatigue testing machine for both FSW butt joint and base metal specimens. The fatigue fractures were observed and analyzed using a scanning electron microscope of JSM-6063LA type. The experimental results show that the fatigue performance of the FSW butt joint of MB8 magnesium alloy is sharply decreased. The conditional fatigue limit （2 x 106） of base metal and welded butt joint is about 77.44 MPa and 49. 91 MPa, respectively. The conditional fatigue limit （2 x 106 ） of the welded butt joint is 64.45% of that of base metal. The main reasons are that the welding can lead to stress concentration in the flash area, tensile welding residual stress in the welded joint（ The residual stress value was 30. 5 MPa）, as well as the grain size is not uniform in the heat-affected zone. The cleavage steps or quasi-cleavage patterns present on the fatigue fracture surface, the fracture type of the FSW butt joint belongs to a brittle fracture.

Repairing of exit-hole in friction-stir-spot welded joints for 2024-T4 aluminum alloy by resistance welding

The exit-hole in friction stir spot welded(FSSWed) 2024-T4 aluminum alloy joints was successfully repaired by using a three-phase secondary rectification resistance spot welding machine, which is termed as filling exit-hole based on resistance welding(FEBRW). The filling dynamic behavior of force was recorded by a device monitoring. Optical microscope(OM), electron backscatter diffraction(EBSD), and tensile shear tests and finite element modelling were conducted to investigate the repairing stages and bonding mechanisms of the repaired joints in detail. Results showed that exit-hole was completely filled and repaired experiencing three stages. Metallurgical bonding was achieved between plug and exit-hole wall in two forms, including melting bonding in the middle of the joints and partial diffusion bonding on both the upper and bottom of the joints. The highest tensile shear strength of the repaired joints was 7.43 kN, which was 36.3% higher than that of the as welded joints. Resistance welding paves an efficient way to repair the exit-hole in FSSWed joints.

Recent research progress in the mechanism and suppression of fusion welding-induced liquation cracking of nickel based superalloys

Nickel-based superalloys are extensively used in the crucial hot-section components of industrial gas turbines,aeronautics,and astronautics because of their excellent mechanical properties and corrosion resistance at high temperatures.Fusion welding serves as an effective means for joining and repairing these alloys;however,fusion welding-induced liquation cracking has been a challenging issue.This paper comprehensively reviewed recent liquation cracking,discussing the formation mechanisms,cracking criteria,and remedies.In recent investigations,regulating material composition,changing the preweld heat treatment of the base metal,optimizing the welding process parameters,and applying auxiliary control methods are effective strategies for mitigating cracks.To promote the application of nickel-based superalloys,further research on the combination impact of multiple elements on cracking prevention and specific quantitative criteria for liquation cracking is necessary.

Effect of heat input on microstructure and mechanical properties of butt-welded dissimilar magnesium alloys joint

The effects of heat input on the microstructures and mechanical properties of tungsten inert gas （TIG） butt-welded AZ31/MB3 dissimilar Mg alloys joint were investigated by microstructural observations, microhardness testing and tensile testing. The results reveal that with the increase of heat input, the width of welding seam increases obviously and the grains both in the fusion zone and the heat affected zone coarsen during TIG welding process. The tensile strength of butt-welded joint increases with the increase of heat input and the maximum joining strength of 242 MPa is obtained with wedding current of 90 A. However, lots of welding pores occur with the further increase of heat input, which results in the decrease of joining strength. It is experimentally demonstrated that robust joint can be obtained by TIG welding process.

Thermal cycle and its influence on the microstructure of laser welded butt joint of 8 mm thick Ti-6Al-4V alloy

Ti-6Al-4V alloy is extensively used in the manufacture of components in aviation.In the current study,the laser welding process is adopted to joint the Ti-6Al-4V alloy plate which has the thick of 8 mm.A three-dimensional finite element model is established to simulate the temperature distribution of laser welding process.The thermal cycle curves are produced on the strength of the simulation results.Meanwhile,the microstructure characteristics of the welded joint are investigated combined with simulation results.The results show that weld zone,heat affected zone and based metal experience similar thermal cycles process and the cooling rate has an important influence on the formation of microstructure.Moreover,the simulation results are well matched with experiment results.

Superplastic formability of Ti-6Al-4V butt-welded plate by laser beam welding

The superplasticity of Ti-6Al-4V butt-welded plates by laser beam welding(LBW)was studied in virtue of hot tensile tests and superplastic bulging tests.Furthermore,microstructural evolution of weld metal upon superplastic forming was systematically analyzed via metallographical tests and scanning electron microscope(SEM).The relation between the microstructure of weld metal and its superplastic ability was discussed.The experimental results show that Ti-6Al-4V butt-welded plates by LBW possess superplasticity.The maximum elongation is up to 154%and the maximum bulge height can be up to 1.81 times the internal radius of the female die.There is an optimum value of the bulge height for bulging gas pressure.