LOAD FLOW CALCULATION FOR FLEXIBLE AC TRANSMISSION SYSTEMS

In this paper, a synthetic mathematical model of load flow for flexible AC transmission systems (FACTS) with unified power flow controller (UPFC) is presented based on the analysis of basic principle and operation state of UPFC. The model can use the fast P Q decoupled load flow method. Examples of test systems show that the proposed model and method have good convergence. An effective tool is provided by the load flow computer program to analyze the load flow and initial valve calculation of the dynamic state of FACTS.

Modeling load distribution for rural photovoltaic grid areas using image recognition

Expanding photovoltaic(PV)resources in rural-grid areas is an essential means to augment the share of solar energy in the energy landscape,aligning with the“carbon peaking and carbon neutrality”objectives.However,rural power grids often lack digitalization;thus,the load distribution within these areas is not fully known.This hinders the calculation of the available PV capacity and deduction of node voltages.This study proposes a load-distribution modeling approach based on remote-sensing image recognition in pursuit of a scientific framework for developing distributed PV resources in rural grid areas.First,houses in remote-sensing images are accurately recognized using deep-learning techniques based on the YOLOv5 model.The distribution of the houses is then used to estimate the load distribution in the grid area.Next,equally spaced and clustered distribution models are used to adaptively determine the location of the nodes and load power in the distribution lines.Finally,by calculating the connectivity matrix of the nodes,a minimum spanning tree is extracted,the topology of the network is constructed,and the node parameters of the load-distribution model are calculated.The proposed scheme is implemented in a software package and its efficacy is demonstrated by analyzing typical remote-sensing images of rural grid areas.The results underscore the ability of the proposed approach to effectively discern the distribution-line structure and compute the node parameters,thereby offering vital support for determining PV access capability.

A Review of the Calculation Methods of Lifting Capacity in Wind Loads on Ocean Platforms

Wind load is a control load that affects the safety of structures in the design of ocean platforms. It has not only direct and powerful effects that may cause structure resonance but also has indirect effects causing waves or currents in the ocean. By analyzing the domestic and international norms, this study presents a review of calculation methods of wind load on ocean platforms, which belongs to large-scale non-entity structure used in the open sea while surrounding wind has no fixed direction. Current computations according to the norms are not accurate, which even not takes the force of the wind against the surface perpendicular to the structure into consideration. Additionally, this study also introduces and compares the lift model of platforms based on different theories, such as vortex-excitation and vibration, engineering structure dynamics, gas flow pressure theory, analyzing their applicability, advantages, and disadvantages. This paper analyzes the limitations and applicable conditions of the existing calculation method itself, such as the lift model is suitable for the existence of stable vortex wake;the calculation method of the structural dynamics of marine engineering must be combined with the wind tunnel test and consider the mistakes caused by the position relationship;the numerical simulation method is accurate but tedious. This study provides an insight into the calculation methods of lift in designing ocean platforms, including the finite element method for simulating fluid force and updating formulas in Chinese norms.

Comparison Structure Forms Between Isogrid and Orthogrid of C/E Composite Trellis Wound Structure Based on Calculation of Load-Carrying

This paper calculated load-carrying of isogrid and orthogrid of carbon-epoxy composite trellis wound structure(C/E CTWS) using non-linear finite element method.Based on the analysis,test cases were designed and tests of axial compression were carried.Analysis result and test result fit well.In order to be used in the project,this kind of structure cut-out repairing was calculated.The method presented in this paper has been proved and can be used to solve complicated engineering problems.According to calculations and experimental results combined with application,a principle of choosing wound structure is obtained and principle could be applied to engineering.

CALCULATION FOR CYLINDRICAL SHELL UNDER LOCAL VERTICAL LOADINGS

In this paper, we use the method of mixed-type series to derive the analytical solutions of cylindrical shell, which is simply supported along the transverse edges and subjected to the local vertical loads, and give the analytical expressions of the solutions for this kind of shell under five types of local vertical loading. A numerical example for a cylindrical shell roof, which is simply supported along the trans verse edges and is free along the longitudinal edges, is given in this paper and from the calculated results it may he seen that the convergence of the solutions is considerably satisfactory. Using the solutions of this paper, we can deal with some practical problems of underground structure.

Calculation Energy of Efficiency New Ginning Machine

Having studied the schedule of influence and change of static loading depending on angular an arrangement saw cylinders we have defined the general spent electric energy on the single-chamber two-cylinder gin, by performing of the calculation the energy consumption per one saw with respect to the angular arrangement of the saw cylinder. Also, provide energy audits gin, were performed at Uzbekistan Namangan region cotton gins in ten manufactures.

The Minimum Rotor Rotation Angle for Calculating On-Load Electromotive Force Waveform of Synchronous Generators

为了快速计算同步发电机负载运行时的稳态性能,希望在转子相对定子旋转的角度尽可能小的情况下就能够准确得到电枢绕组电动势波形。根据电机理论,针对分数槽绕组同步发电机负载运行时的气隙磁通密度进行分析,得到了准确计算电枢绕组电动势波形的转子最小旋转角。应用有限元法计算最小旋转角范围内定、转子不同位置下的电磁场,通过对电磁场计算结果进行后处理,得到了定子每个齿磁通在一个或者多个周期的变化波形,从而快速计算电枢绕组电动势波形。对两台不同电枢绕组形式的永磁同步发电机负载电动势波形进行了计算,通过对计算结果进行比较,验证了方法的正确性。在一台电机上进行了实验,计算结果和实验结果较吻合。该方法具有计算准确以及计算量小的优点。

Damage-ignition mechanism studies on modified propellant with different crosslinking density under dynamic loading

The study of high-energy and low-vulnerability propellants is important for the power performance and safety of solid propellant rocket motors.The modified split Hopkinson pressure bar(SHPB)tests are performed on two kinds of propellant with different crosslinking density to study the dynamic mechanical responses and damage-ignition mechanism.SHPB apparatus is equipped with a highperformance infrared camera and high-speed camera to capture the deformation,damage-ignition feature and temperature evolution images in the impact process.The results suggested that the mechanical responses and damage-ignition mechanism of the propellants were affected by the strain rates and crosslinking density.The damage-ignition degree is more intense and the reaction occurs earlier with the increase of strain rates.For propellant 1 with higher crosslinking density,the critical ignition strain rate is 4500 s^(-1).Two kinds of propellants show different ignition mechanism,i.e.crack generation,propagation and final fracture for propellant 1 while viscous shear flow for propellant 2.Meanwhile,the SEM images also reveal the difference of damage-ignition mechanism of the two kinds of propellants.Finally,the ignition mechanism under different strain rates and critical ignition strain rate of propellants are further explained by the theoretical calculation of temperature variations.

腐蚀疲劳交替下2A12-T4航空铝合金的寿命分析研究

基于飞机服役期间经历“地面腐蚀与空中疲劳”的交替损伤模式,考虑载荷间的相互作用,研究了航空铝合金2A12-T4在预腐蚀与“腐蚀+疲劳”交替模式下疲劳寿命的退化与损伤累积规律。同级加载条件下提出利用腐蚀疲劳耦合损伤指数和迟滞载荷用来描述考虑交替腐蚀疲劳损伤模式,用各级疲劳损伤间的相互影响及腐蚀损伤与疲劳损伤在服役工作期间的耦合作用来描述腐蚀、疲劳间的相互促进、加速劣化的现象。基于损伤力学和非线性累积理论,考虑载腐蚀疲劳耦合指数与迟滞载荷对传统的Miner线性累积损伤理论进行修正。建立了飞机结构材料的寿命计算模型,并将模型计算结果与试验结果进行对比验证。确定了腐蚀实验中的腐蚀耦合损伤,并利用低载锻炼效应理论得出均匀分布的迟滞载荷。计算结果表明,本文提出的寿命计算模型的结果与实验结果比较吻合。

考虑节点刚度随机性的焊接钢筋部品变形计算方法研究

为量化钢筋部品刚度,从受力机理角度出发,基于试验和理论分析,提出考虑刚度随机性的焊接钢筋部品变形计算方法。从受力机理的角度提出三向转动刚度独立力学求解模型,考虑钢筋直径的影响,设计了105组T形焊接钢筋试件及两类加载固定试验装置,开展分级加载试验;在此基础上,考虑焊接节点转动刚度随机性,提出基于蒙特卡洛随机抽样的焊接钢筋部品变形计算方法,并分别开展了6个焊接钢筋网片和6个钢筋块体试验进行验证。结果表明:钢筋焊接节点刚度与钢筋直径有关,当焊接条件相同时,钢筋直径越大,焊接节点刚度越大;同一钢筋直径组合的焊接节点转动刚度基本符合正态分布,3个方向的转动刚度R x>R z>R y;钢筋焊接节点刚度与焊接节点断面面积基本呈线性关系;竖筋和横筋连接节点刚度对钢筋部品变形影响显著,所采用的节点刚度取值方法计算的焊接钢筋部品变形偏差均在10%以内,与传统刚接和铰接方法相比,变形计算精度大幅提高,变形计算方法合理。

三峡库区滑坡涌浪作用下桥墩波压特性研究

由于三峡库区的非开敞性,滑坡引起的涌浪衰减较慢,传播过程中可能对沿程桥墩产生巨大破坏。以涪陵长江二桥为依托,构建了比例尺为1∶70的库区河道水槽,试验模拟了滑坡涌浪对桥墩的作用。结果表明:桥墩上涌浪波压分为共振波压(P_(re))和脉动波压(P_(pu)),共振波压为涌浪冲击桥墩瞬间桥墩共振产生的高频振动波,频率为300.0~400.0 Hz;脉动波压为波浪作用过程产生的压力,频率为0.2~0.5 Hz;脉动波压在对岸桥墩上沿水深的分布近似为垂直分布,在同岸桥墩沿水深锯齿状减小,最大脉动波压分布在水面附近;共振波压沿水深分为单峰值、多峰值和无峰值3种,10万m^(3)以上大方量滑坡产生的共振波压为单峰值和多峰值分布,单峰值的峰值波压是水面波压的5.0倍,多峰值的峰值波压为水面波压的2.5倍~4.0倍,10万m^(3)以下滑坡产生的共振波压呈现无峰值分布;共振波压沿水深呈先增大后减小的“侧V”形;P_(re)/P_(pu)最大位置在距水面1/3水深位置,第二大位置在距水面1/5水深位置。该文提出了桥墩迎波面涌浪压力荷载计算模型,并针对三峡库区不同运行水位给出了相应水位条件下最大涌浪波压的计算公式。

盾构废弃黏土泥浆真空脱水试验与理论研究

针对泥浆池中盾构废弃泥浆在上部真空脱水作用下倒渣及运渣受限等问题,提出了一种废弃泥浆底部真空脱水方法。采用自行研制的废弃泥浆底部真空脱水装置开展了自重、自重+底部真空荷载、自重稳定+底部真空荷载、自重稳定+底部分级真空荷载4组不同脱水荷载工况下废弃黏土泥浆模型试验,分析了废弃黏土泥浆的泥‒水界面沉降量、孔隙水压力以及脱水后含水率和总脱水量等物理量的变化规律。结果表明,先对废弃泥浆进行自重脱水处理,再对其底部分级施加真空作用的脱水方式具有更好的脱水效果。采用该方法对初始含水率为103.00%的废弃黏土泥浆进行脱水处理后,含水率分布范围为37.10%~62.65%,其内部孔隙水压力的最小值可达−73.09 kPa,接近底部真空作用值−80.00 kPa;且该工况相较于其余3种工况,平均沉降量分别提高了106.40%、2.91%、6.15%,总脱水量分别提高了122.0%、8.0%、5.1%。同时,基于分段线性化有限差分(CS2)模型建立了废弃黏土泥浆真空脱水数值计算模型,对废弃黏土泥浆在脱水过程中泥‒水界面沉降量进行数值模拟,验证了数值计算模型的有效性。

底部双排配筋单孔空心预制梁力学性能试验研究

为了研究新型装配式单孔空心预制梁的抗弯承载力和变形性能,并提高其工作性能。试验共设计并制作了3根单孔空心预制梁和1根实心预制梁,通过试验和理论计算相结合的分析手段,重点研究单孔空心预制梁和实心预制梁的破坏机理、裂缝发展、荷载-挠度曲线、变形性能及抗弯承载力等。结果表明:单孔空心预制梁与普通实心预制梁的破坏特征相似,且其裂缝分布较均匀、间距小,延性好;在相同荷载作用下,单孔空心预制梁挠度大于实心预制梁,其整体受力变形性能相对优越。提出了截面有效面积等效法和混凝土轴心抗压强度等效法2种计算方法,通过对比分析发现,混凝土轴心抗压强度等效法计算值误差仅为0.82%,满足工程要求,而且单孔空心预制梁与实心梁相比还可节约材料8.72%。因此,单孔空心预制梁具有良好的应用前景。

变负载条件下超声电源有功功率的整定与测量

针对变负载条件下超声电源有功功率测量精度较低与高次谐波干扰的问题,提出一种功率测量方法。该方法采用电容分压与电流互感器采集超声系统中换能器两端的电压与电流信号,经过A/D芯片转换为数字信号后设计带通滤波器滤除高次谐波,通过数字鉴相器得到包含相位差的直流分量,结合改进的有效值计算方法得到变负载条件下的电压电流信号有效值,计算得到有功功率,实现超声系统驱动换能器工作于变负载条件下的功率参数高精度测量。最后通过仿真与实验验证了该测量方案的可行性与正确性。

波形钢腹板工字梁的等效计算模型及稳定性分析

基于变形与应变能相等的原则,提出波形钢腹板工字梁的等效平直钢腹板计算模型。通过波形钢腹板直板段与斜板段应变分析,推导了波形钢腹板工字梁及等效计算模型的应变能,建立等效惯性矩与等效扇性惯性矩,利用平直钢腹板工字梁的临界荷载计算公式,对波形钢腹板工字梁进行稳定性分析。研究结果表明:该方法简单、便捷,对波形钢腹板工字梁的稳定分析准确、有效;建立的等效惯性矩与翘曲惯性矩仅取决于截面及波形钢板尺寸,不受工字梁的边界条件、跨径等因素的影响,具有良好的适应性。

基于S变换双阈值法的汽车零部件载荷谱加速编辑

针对S变换编辑法加速编辑效果不佳的问题,提出了一种基于S变换双阈值编辑方法。该方法先对载荷谱进行S变换以获取最大幅值谱,在以双阈值识别并保留的幅值谱片段为依据保留对应的载荷谱片段后,再将其拼接成加速后的载荷谱,最后对比分析S变换双阈值编辑法与S变换编辑法编辑的加速谱的统计参数、功率谱密度、穿级计数和疲劳仿真结果。研究结果表明,S变换双阈值编辑法可明显压缩原始载荷时间,且其压缩效率高于S变换编辑法,转向节的疲劳损伤和寿命分析误差更小,适用于汽车零部件载荷谱加速编辑研究。

圆钢管型钢再生混凝土组合柱水平承载力计算方法研究

通过对11个圆钢管型钢再生混凝土组合柱进行低周反复荷载试验,分析再生粗骨料取代率、型钢截面形式、轴压比、型钢配钢率及圆钢管壁厚参数对组合柱水平承载力的影响规律;观察了组合柱的破坏形态及特征,研究了圆钢管、型钢翼缘及腹板应变的发展规律,分析了组合柱的地震破坏特征。研究表明,在水平地震作用下组合柱发生典型的压弯塑性铰破坏。在此基础上,结合现有规范提出了基于叠加原理的圆钢管型钢再生混凝土组合柱水平承载力计算方法。计算结果表明,其水平承载力计算值与试验值吻合度较好,能较为准确地预测组合柱的水平承载力。

基于多能流耦合规律的综合能源系统潮流及流分析

从能量流和流两个角度分析综合能源系统的多能流耦合规律,建立系统能流稳态潮流模型和流模型,根据模型特点研究系统潮流和流分布计算方法,以算例验证计算方法的可行性并分析计算数据,验证流机理模型相比于黑箱模型在局部分析方面的优越性。以算例数据为例,分析其潮流及流分布特点,结果表明:算例系统中能源转换环节的地方损最大,为系统薄弱环节,值得着重改进;同时电、热网络也有部分管段损较大,优化局部网络时也应纳入考虑。

框桁式墙体抗震性能试验及影响因素研究

为研究新型框桁式墙体抗震能力,设计4片框桁式墙体试件进行拟静力试验,对比分析了墙体试件的破坏形态、滞回曲线、承载力、延性及性能特征点。并应用ABAQUS软件建立墙体的非线性数值模型,考虑了轴压比、混凝土强度、配箍率和配筋率等因素的影响,计算得到了荷载-位移曲线,分析了承载力及延性变化特征。结果表明:各墙体试件破坏过程为,内部桁杆先于外框墙肢发生变形并耗能,而后桁杆与外墙肢的底部相交处形成塑性区并破坏;在桁式杆件中配置角钢、增大混凝土强度、配箍率和纵筋配筋率也可提高试件延性,而配置角钢时,配筋率对承载力的影响不明显,混凝土强度较高时,其延性不再明显提高;增大轴压比可提高试件的承载力,但会使试件的延性降低。研究结果可为框桁式墙体抗震设计提供依据。

初始加载龄期对陶粒混凝土梁徐变性能的影响

徐变性能对混凝土结构的承载性能有较大影响,初始加载龄期(养护龄期)对徐变有较大影响,基于4种不同初始加载龄期的陶粒混凝土梁,进行了为期200 d的徐变试验,研究初始加载龄期对陶粒混凝土梁徐变性能的影响规律试验研究,并建立基于ACI-209徐变计算模型和ACI-435长期挠度计算方法建立陶粒混凝土结构的徐变值计算式。结果显示:随着初始加载龄期的增加,陶粒混凝土梁的初始挠度、徐变挠度速度和最终挠度值均呈现减小的趋势,减小的幅度也随着加载龄期的延长而逐渐减弱;徐变值计算式的计算值与试验观测值较接近,所建立的计算式具有较好的准确性和适用性;综合考虑工期和经济指标,建议将90 d作为预制陶粒混凝土梁的加载龄期。研究结论可为陶粒混凝土结构徐变计算提供参考。