Numerical Study on the Aerodynamic and Fluid−Structure Interaction of An NREL-5MW Wind Turbine

A 5-MW wind turbine has been modeled and analyzed for fluid-structure interaction and aerodynamic performance.In this study, a full-scale model of a 5-MW wind turbine is first developed based on a computational fluid dynamics(CFD) approach, in which the unsteady, noncompressible Reynolds Averaged Navier-Stokes(RANS) method is used. The main focus of the study is to analyze the tower shadow effect on the aerodynamic performance of the wind turbine under different inlet flow conditions. Subsequently, the finite element model is established by considering fluid/structure interactions to study the structural stress, displacement, strain distributions and flow field information of the structure under the uniform wind speed. Finally, the fluid-structure interaction model is established by considering turbulent wind and the tower shadow effect. The variation rules of the dynamic response of the one-way and two-way fluid-structure interaction(FSI) models under different wind speeds are analyzed, and the numerical calculation results are compared with those of the centralized mass model. The results show that the tower shadow effect and structural deformation are the main factors affecting the aerodynamic load fluctuation of the wind turbine, which in turn affects the aerodynamic performance and structural stability of the blades. The structural dynamic response of the coupled model shows significant similarity, while the structural displacement response of the former exhibits less fluctuation compared with the conventional centralized mass model. The one-way fluid-structure interaction(FSI)model shows a higher frequency of stress-strain and displacement oscillations on the blade compared with the two-way FSI model.

Comprehensive Examination of Solar Panel Design: A Focus on Thermal Dynamics

In the 21st century, the deployment of ground-based Solar Photovoltaic (PV) Modules has seen exponential growth, driven by increasing demands for green, clean, and renewable energy sources. However, their usage is constrained by certain limitations. Notably, the efficiency of solar PV modules on the ground peaks at a maximum of 25%, and there are concerns regarding their long-term reliability, with an expected lifespan of approximately 25 years without failures. This study focuses on analyzing the thermal efficiency of PV Modules. We have investigated the temperature profile of PV Modules under varying environmental conditions, such as air velocity and ambient temperature, utilizing Computational Fluid Dynamics (CFD). This analysis is crucial as the efficiency of PV Modules is significantly impacted by changes in the temperature differential relative to the environment. Furthermore, the study highlights the effect of airflow over solar panels on their temperature. It is found that a decrease in the temperature of the PV Module increases Open Circuit Voltage, underlining the importance of thermal management in optimizing solar panel performance.

A Computational Fluid Dynamics (CFD) Analysis of an Undulatory Mechanical Fin Driven by Shape Memory Alloy

Many fishes use undulatory fin to propel themselves in the underwater environment. These locomotor mechanisms have a popular interest to many researchers. In the present study, we perform a three-dimensional unsteady computation of an undulatory mechanical fin that is driven by Shape Memory Alloy （SMA）. The objective of the computation is to investigate the fluid dynamics of force production associated with the undulatory mechanical fin. An unstructured, grid-based, unsteady Navier-Stokes solver with automatic adaptive remeshing is used to compute the unsteady flow around the fin through five complete cycles. The pressure distribution on fin surface is computed and integrated to provide fin forces which are decomposed into lift and thrust. The velocity field is also computed throughout the swimming cycle. Finally, a comparison is conducted to reveal the dynamics of force generation according to the kinematic parameters of the undulatory fin （amplitude, frequency and wavelength）.

COMPUTATIONAL FLUID DYNAMICS(CFD) SIMULATIONS OF DRAG REDUCTION WITH PERIODIC MICRO-STRUCTURED WALL

Computational fluid dynamics（CFD） simulations are adopted to investigate rectangular microchannel flows with various periodic micro-structured wall by introducing velocity slip boundary condition at low Reynolds number. The purpose of the current study is to numerically find out the effects of periodic micro-structured wall on the flow resistance in rectangular microchannel with the different spacings between microridges ranging from 15 to 60 pm. The simulative results indicate that pressure drop with different spacing between microridges increases linearly with flow velocity and decreases monotonically with slip velocity; Pressure drop reduction also increases with the spacing between microridges at the same condition of slip velocity and flow velocity. The results of numerical simulation are compared with theoretical predictions and experimental results in the literatures. It is found that there is qualitative agreement between them.

Computational Fluid Dynamics(CFD) Analysis and Optimization of Reconstructed Intake System of Cylinder Head Based on Slicing Reverse Method

To find out and improve the flow characteristics inside the intake system of cylinder head,the application of computational fluid dynamics(CFD)in the evaluation and optimization of the reconstructed intake system based on slicing reverse method was proposed.The flow characteristics were found out through CFD,and the velocity vector field,pressure field and turbulent kinetic energy field for different valve lifts were discussed,which were in good agreement with experimental data,and the quality of reconstruction was evaluated.In order to improve its flow characteristic,an optimization plan was proposed.The results show that the flow characteristics after optimization are obviously improved.The results can provide a reference for the design and optimization of the intake system of cylinder head.

Study on cavern evolution and performance of three mixers in agitation of yield-pseudoplastic fluids

The hydrodynamic performance of three mixers single shaft central mixer(SSC), single shaft off-centred mixer(SSO), dual shaft off-centred mixer(DSO), was investigated in the mixing of yield-pseudoplastic fluids(xanthan gum solutions) in the laminar regime. To explore and determine the efficiency of three mixers, both numerical and experimental approaches were adopted. The fluid rheology was described by the Herschel–Bulkley rheological model. Computational fluid dynamics was employed to simulate the apparent viscosity distribution, mixing time, and the flow pattern inside the stirred tank. The developed model was validated through experimentally measured torque. The influence mechanism of the rotational speed and fluid rheology on the cavern evolution was explored deeply. The performances of three mixers in this work were compared at the constant power input and fluid rheology with respect to the flow pattern, mixing time, and mixing efficiency. The results verify that the faster the rotating speed, the greater influence of the fluid rheology on the cavern evolution, and the more uniform apparent viscosity distribution. Moreover, the mixing time decreases continuously as the increasing power consumption per unit volume, and the dimensionless mixing time of DSO mixer was nearly 42.8% and 6.1% shorter than that of SSC and SCO mixer at the same Reynolds number, respectively. According to the mixing efficiency criteria, these data also revealed that DSO was more efficient than SSC and SSO.

Particulate flow modelling in a spiral separator by using the Eulerian multi-fluid VOF approach

The Euler-Euler model is less effective in capturing the free surface of flow film in the spiral separator,and thus a Eulerian multi-fluid volume of fluid(VOF)model was first proposed to describe the particulate flow in spiral separators.In order to improve the applicability of the model in the high solid concentration system,the Bagnold effect was incorporated into the modelling framework.The capability of the proposed model in terms of predicting the flow film shape in a LD9 spiral separator was evaluated via comparison with measured flow film thicknesses reported in literature.Results showed that sharp air–water and air-pulp interfaces can be obtained using the proposed model,and the shapes of the predicted flow films before and after particle addition were reasonably consistent with the observations reported in literature.Furthermore,the experimental and numerical simulation of the separation of quartz and hematite were performed in a laboratory-scale spiral separator.When the Bagnold lift force model was considered,predictions of the grade of iron and solid concentration by mass for different trough lengths were more consistent with experimental data.In the initial development stage,the quartz particles at the bottom of the flow layer were more possible to be lifted due to the Bagnold force.Thus,a better predicted vertical stratification between quartz and hematite particles was obtained,which provided favorable conditions for subsequent radial segregation.

Microfluidic field strategy for enhancement and scale up of liquid-liquid homogeneous chemical processes by optimization of 3D spiral baffle structure

Due to the scale effect, the uniform distribution of reagents in continuous flow reactor becomes bad when the channel is enlarged to tens of millimeters. Microfluidic field strategy was proposed to produce high mixing efficiency in large-scale channel. A 3D spiral baffle structure(3SBS) was designed and optimized to form microfluidic field disturbed by continuous secondary flow in millimeter scale Y-shaped tube mixer(YSTM). Enhancement effect of the 3SBS in liquid-liquid homogeneous chemical processes was verified and evaluated through the combination of simulation and experiment. Compared with 1 mm YSTM, 10 mm YSTM with 3SBS increased the treatment capacity by 100 times, shortened the basic complete mixing time by 0.85 times, which proves the potential of microfluidic field strategy in enhancement and scale-up of liquid-liquid homogeneous chemical process.

Application of Computational Fluid Dynamics and Fluid Structure Interaction Techniques for Calculating the 3D Transient Flow of Journal Bearings Coupled with Rotor Systems

Journal bearings are important parts to keep the high dynamic performance of rotor machinery. Some methods have already been proposed to analysis the flow field of journal bearings, and in most of these methods simplified physical model and classic Reynolds equation are always applied. While the application of the general computational fluid dynamics （CFD）-fluid structure interaction （FSI） techniques is more beneficial for analysis of the fluid field in a journal bearing when more detailed solutions are needed. This paper deals with the quasi-coupling calculation of transient fluid dynamics of oil film in journal bearings and rotor dynamics with CFD-FSI techniques. The fluid dynamics of oil film is calculated by applying the so-called ＂dynamic mesh＂ technique. A new mesh movement approacb is presented while the dynamic mesh models provided by FLUENT are not suitable for the transient oil flow in journal bearings. The proposed mesh movement approach is based on the structured mesh. When the joumal moves, the movement distance of every grid in the flow field of bearing can be calculated, and then the update of the volume mesh can be handled automatically by user defined function （UDF）. The journal displacement at each time step is obtained by solving the moving equations of the rotor-bearing system under the known oil film force condition. A case study is carried out to calculate the locus of the journal center and pressure distribution of the journal in order to prove the feasibility of this method. The calculating results indicate that the proposed method can predict the transient flow field of a journal bearing in a rotor-bearing system where more realistic models are involved. The presented calculation method provides a basis for studying the nonlinear dynamic behavior of a general rotor-bearing system.

Simulation investigation on fluid characteristics of jet pipe water hydraulic servo valve based on CFD

Simulation investigation on fluid characteristics of the water hydraulic jet pipe servo valve （WHJPSV） is conducted through a commercial computational fluid dynamics （CFD） software package FLUENT. In particular, the factors to fluid characteristics of WHJPSV are addressed, which include diameter combination of jet pipe and receiver pipe, jet pipe nozzle clearance, angle between two jet receiver pipes and deflection angle of the jet pipe. It is concluded from the results that： （i） Structural parameters have great influences on fluid characteristics of WHJPSV, when d1 = d2 = 0.3 mm, α= 45 , b = 0.5 mm, and the simulation exhibits better fluid characteristics; （ii） The magnitude of the recovery pressure and flow velocity increase almost linearly with the deflection angle of jet pipe. The research work in this paper is important for determining and optimizing the structural parameters of the jet pipe and jet receiver. The relevant conclusions could be extended to the study of other water hydraulic servo control components.

调谐液柱阻尼器-结构系统风致振动响应的CFD/CSD耦合分析方法

针对调谐液柱阻尼器(tuned liquid column damper, TLCD)难以建立其精确的非线性理论分析模型,且其力学性能试验成本高和耗时长等问题,首先采用计算流体动力学(CFD)数值模拟方法,对TLCD系统的力学性能和动力特征进行仿真模拟,在此基础上进一步提出了基于计算流体动力学/计算结构动力学(CFD/CSD)耦合分析方法,求解带TLCD系统的高层建筑结构的风致动力响应。通过开展某一TLCD系统在特定底部激励下的力学性能和动力特性试验,得到其内液体晃荡的自由液面波高和晃动力时程,验证了CFD数值模拟方法可以准确地分析TLCD水箱内液体的非线性晃动特征。随后对风工程领域广泛采用的76层建筑结构振动控制Benchmark模型,假设其顶部设置TLCD系统时主体结构在三种风速重现期(10、50和100年)风速对应的横风向动力风荷载激励下的风致控制效率,采用提出的CFD/CSD耦合分析方法,进行了数值仿真模拟分析。耦合分析结果表明,TLCD系统对Benchmark模型的风致加速度、速度和位移响应均有一定的控制效果,对加速度响应的控制效果要优于对位移响应的控制效果。该研究方法可为复杂TLCD系统对高层建筑的风振控制分析提供有效的参考。

Application of computational fluid dynamics simulation for submarine oil spill

Computational fluid dynamics （CFD） codes are being increasingly used in the simulation of submarine oil spills. This study focuses on the process of oil spills, from damaged submarine pipes, to the sea surface, using numerical models. The underwater oil spill model is developed, and a description of the governing equations is proposed, along with modifications required for the particalization of the control volume. Available experimental data were introduced to evaluate the validity of the CFD predictions, the results of which proved to be in good agreement with the experimental data. The effects of oil leak rate, leak diameter, current velocity, and oil density are investigated, by the validated CFD model, to estimate the undersea leakage time, the lateral migration distance, and surface diffusion range when the oil reaches the sea surface. Results indicate that the leakage time and lateral migration distance increase with decreasing leak rates and leak diameter, and increase with increasing current velocity and oil density. On the other hand, a large leak diameter, high density, high leak rate, or fast currents result in a greater surface diffusion range. The findings and analysis presented here will provide practical predictions of oil spills, and guidance for emergency rescues.

COMPUTATIONAL FLUID DYNAMICS RESEARCH ON PRESSURE LOSS OF CROSS-FLOW PERFORATED MUFFLER

The pressure loss of cross-flow perforated of physical modeling, simulation and data processing. muffler has been computed with the procedure Three-dimensional computational fluid dynamics （CFD） has been used to investigate the relations of porosities, flow velocity and diameter of the holes with the pressure loss. Accordingly, some preliminary results have been obtained that pressure loss increases with porosity descent as nearly a hyperbolic trend, rising flow velocity of the input makes the pressure loss increasing with parabola trend, diameter of holes affects little about pressure loss of the muffler. Otherwise, the holes on the perforated pipes make the air flow gently and meanly, which decreases the air impact to the wall and pipes in the muffler. A practical perforated muffler is used to illustrate the available of this method for pressure loss computation, and the comparison shows that the computation results with the method of CFD has reference value for muffler design.

基于CFD的FPSO风载荷规范计算适用性研究

[目的]目前,设计人员多使用针对大型油轮的OCIMF规范和针对海上平台的API规范对FPSO风载荷进行计算,但因FPSO船舶上层建筑更为复杂,需进一步研究这2种规范对于FPSO风载荷计算的适用性。[方法]建立具有通用型上部模块的某30万吨级大型FPSO数值模型,对恶劣海况下不同风向角、横倾角下的FPSO所受风载荷进行数值模拟,分析其中存在的遮蔽效应;与规范计算结果进行对比分析,讨论在风载荷作用下FPSO受到的横倾力矩。[结果]结果显示,船舶正浮状态受到的最大风载荷和横倾力矩出现在270°风向角;船舶横倾状态下受到的风载荷和横倾力矩比正浮状态更大,最大横倾力矩出现在10.5°横倾角280°风向角;采用API规范和OCIMF规范得到的FPSO风载荷计算结果与CFD计算结果相差较大,二者在270°风向角的结果与CFD分别相差13.6%和24.5%。[结论]数值仿真给出的流场细节有利于分析上部模块间的遮蔽效应,能够较为准确地预报船舶所受到的风载荷,可以为考虑遮蔽效应的FPSO稳性设计提供参考。

Computational fluid dynamics simulation of a novel bioreactor forsophorolipid production

This paper describes three-dimensional computational fluid dynamics(CFD) simulations of gas–liquid flow in a novel laboratory-scale bioreactor contained dual ventilation-pipe and double sieve-plate bioreactor(DVDSB)used for sophorolipid(SL) production. To evaluate the role of hydrodynamics in reactor design, the comparisons between conventional fed-batch fermenter and DVDSB on the hydrodynamic behavior are predicted by the CFD methods. Important hydrodynamic parameters of the gas–liquid two-phase system such as the liquid phase velocity field, turbulent kinetic energy and volume-averaged overall and time-averaged local gas holdups were simulated and analyzed in detail. The numerical results were also validated by experimental measurements of overall gas holdups. The yield of sophorolipids was significantly improved to 484 g·L^(-1)with a 320 h fermentation period in the new reactor.

The influence of temperature on flow-induced forces on quartz-crystal-microbalance sensors in a Chinese liquor identification electronic-nose: three-dimensional computational fluid dynamics simulation and analysis

An electronic-nose is developed based on eight quartz-crystal-microbalance (QCM) gas sensors in a sensor box, and is used to detect Chinese liquors at room temperature. Each sensor is a highly-accurate and highly-sensitive oscillator that has experienced airflow disturbances under the condition of varying room temperatures due to unstable flow-induced forces on the sensors surfaces. The three-dimensional (3D) nature of the airflow inside the sensor box and the interactions of the airflow on the sensors surfaces at different temperatures are studied by computational fluid dynamics (CFD) tools. Higher simulation accuracy is achieved by optimizing meshes, meshing the computational domain using a fine unstructural tetrahedron mesh. An optimum temperature, 30 ℃, is obtained by analyzing the distributions of velocity streamlines and the static pressure, as well as the flow-induced forces over time, all of which may be used to improve the identification accuracy of the electronic-nose for achieving stable and repeatable signals by removing the influence of temperature.

Computational Fluid Dynamics Analysis of Shroud Design on Hemodynamic Performance and Blood Damage in a Centrifugal Blood Pump

Patients with extracorporeal membrane oxygenation still suffer from high rates of complication that linked to the flow field within the blood pump.So it is essential to optimise the geometry of the pump.The specification of shroud design is arguably the necessary design parameter in the centrifugal pump.However,the hemodynamic performances of the different shroud designs have not been studied extensively.In this study,ten different shroud designs were made and divided into two groups as the different covering locations(A:Covering the blade leading edge,B:Covering the blade trailing edge).In every group,six shroud designs with the covering proportions of 0,1/5,2/5,3/5,4/5,1 were made.Detailed computational fluid dynamics(CFD)analyses were performed to investigate their effects on hemodynamics and hydraulic performance at the constant flow condition(4000 rpm,5 L/min).The percentage volumes of the scalar shear stress in specific threshold(τ<1 Pa:Thrombosis,τ>9 Pa:the destruction of von Willebrand factor,τ>50 Pa:Platelet activation,τ>150 Pa:Break of red blood)were used to compare the blood damage of the different shroud designs.Also,the modified index of hemolysis(MIH)were calculated based on a Eulerian approach for different pumps.CFD simulations predicted an increase in the pump head,hydraulic efficiency,a fraction of fluid volume with scalar shear stress values above a threshold(9 Pa,50 Pa,150 Pa)and MIH with increasing shroud covering proportions from 0 to 1 in the same covering location.Also,these above results were higher in group B than group A.This means that the risks of the hemolysis,thrombosis and bleeding increased as the rise of the covering proportion and they were higher in the pump whose shroud covers the blade trailing edge.

Computational simulation of fluid dynamics in a tubular stirred reactor

The flow and concentration fields in a new style tubular stirred reactor were simulated by simulating the fluids dynamics(CFD),in which FLUENT software was used and the standard k-ε model and multiple reference frame(MRF) were adopted. The various values of initial rotating speed and inlet flow rate were adopted. Simulations were validated with experimental residence time distribution(RTD) determination. It is shown that the fluid flow is very turbulent and the flow pattern approaches to the plug flow. The velocity increases from shaft to the end of impeller,and the gradient is enlarged by increasing the rotating speed. Comparison between RTD curves shows that agitation can improve the performance of reactor. As the flow rate increases,the mean residence time decreases proportionally,and the variance of RTD lessens as well. When rotating speed increases to a certain value,the variance of RTD is enlarged by increasing rotating speed,but the mean residence time has no obvious change.

Computational fluid dynamics simulation of gas-liquid two phases flow in 320 m^3 air-blowing mechanical flotation cell using different turbulence models

According to the recently developed single-trough floating machine with the world's largest volume(inflatable mechanical agitation flotation machine with volume of 320 m3) in China, the gas-fluid two-phase flow in flotation cell was simulated using computational fluid dynamics method. It is shown that hexahedral mesh scheme is more suitable for the complex structure of the flotation cell than tetrahedral mesh scheme, and a mesh quality ranging from 0.7 to 1.0 is obtained. Comparative studies of the standard k-ε, k-ω and realizable k-ε turbulence models were carried out. It is indicated that the standard k-ε turbulence model could give a result relatively close to the practice and the liquid phase flow field is well characterized. In addition, two obvious recirculation zones are formed in the mixing zones, and the pressure on the rotor and stator is well characterized. Furthermore, the simulation results using improved standard k-ε turbulence model show that surface tension coefficient of 0.072, drag model of Grace and coefficient of 4, and lift coefficient of 0.001 can be achieved. The research results suggest that gas-fluid two-phase flow in large flotation cell can be well simulated using computational fluid dynamics method.

基于CFD变形网格法的螺旋桨水中附加转动惯量研究

为了在螺旋桨设计中较为准确地估算螺旋桨在水中的附加转动惯量,为轴系设计提供更为准确的设计输入,并进一步探究螺旋桨设计参数对于附加转动惯量的影响规律,以通用计算流体力学(CFD)软件STAR-CCM+为平台,运用内置的变形网格技术,以某油船螺旋桨为研究对象,进行基于RANS方程全粘流的附加转动惯量数值计算研究。在此基础上,通过参数变换获取两组弦长和螺距等比例变化的螺旋桨模型,计算其附加转动惯量并分析和设计参数之间的关系。结果表明:对于同一弦长分布的桨,附加转动惯量占比(水中附加转动惯量除以自身转动惯量)随螺距的增加而增加;对于同样螺距分布的桨,附加转动惯量占比随弦长的增加而减小。通过回归分析,建立螺旋桨水中附加转动惯量与弦长及螺距的回归模型,实现了设计中的快速预报。