Taylor–Couette–Poiseuille(TCP)flow dominates the inner water-cooling circulation of canned motor reactor coolant pumps.Current research on TCP flow focuses on torque behaviors and flow regime transitions through exp...Taylor–Couette–Poiseuille(TCP)flow dominates the inner water-cooling circulation of canned motor reactor coolant pumps.Current research on TCP flow focuses on torque behaviors and flow regime transitions through experiments and simulations.However,research on axial flow resistance in a large Reynolds number turbulent state is not sufficient,especially for the various flow patterns.This study is devoted to investigating the influence of annular flow on the axial flow resistance of liquid in the coaxial cylinders of the stator and rotor in canned motor reactor coolant pumps,and predicting the coolant flow distribution between the upper coil cooling loop and lower bearing lubricating loop for safe operation.The axial flow resistance,coupled with the annular rotation,is experimentally investigated at a flow rate with an axial Reynolds number,Rea,from 2.6×10~3 to 6.0×10~3 and rotational Reynolds number,Ret,from 1.6×10~4 to 4.0×10~4.It is revealed that the axial flow frictional coe cient varies against the axial flow rate in linear relation sets with logarithmic coordinates,which shift up when the flow has a higher Ret.Further examination of the axial flow resistance,with the Rea extending to 3.5×10~5 and Ret up to 1.6×10~5,by simulation shows gentle variation rates in the axial flow frictional coe cients against the Rea.The relation curves with different Ret values converge when the Rea exceeds 3.5×10~5.A prediction model for TCP flow consisting of a polygonal approximation with logarithmic coordinates is developed to estimate the axial flow resistance against different axial and rotational Reynolds numbers for the evaluation of heat and mass transfer during transition states and the engineering design of the canned motor chamber structure.展开更多
In addition to the characteristics of a conventional motor, a novel direct-drive double-stator permanent-magnet brushless motor proposed can operate in the state of either a generator or a motor as appropriate. Throug...In addition to the characteristics of a conventional motor, a novel direct-drive double-stator permanent-magnet brushless motor proposed can operate in the state of either a generator or a motor as appropriate. Through numerical calculation and analysis, the output torque of double-stator permanent-magnet brushless motor of the same volume as the traditional machine is discussed, and the reduction of torque ripple by using the structure features of this motor is investigated. The results indicate that lower torque ripple under the condition of ideal effective torque can be obtained by the rational design of motor. The prototype motors tested show that this kind of motor structure has a higher power density.展开更多
A new-style direct drive motor with double-stator structure is proposed. The structure and principle of the permanent-magnet (PM) brushless motor are discussed. On the basis of numerical calculation, the cogging torqu...A new-style direct drive motor with double-stator structure is proposed. The structure and principle of the permanent-magnet (PM) brushless motor are discussed. On the basis of numerical calculation, the cogging torque waveforms of the prototype motor when staggering two stators are analyzed. The method that can reduce torque ripple making use of the structure features of this motor is investigated. The results of numerical calculation and experiment indicate that designing motor with this kind of structure is a good scheme for increasing the power density.展开更多
为解决电动汽车驱动电机控制器主控芯片TMS320F28377S应用程序升级维护操作困难的问题,设计开发一种基于控制器局域网络(controller area network,CAN)通信技术的固件升级系统。通过配置CAN模块及Flash模块,解析HEX文件,结合汉明码校验...为解决电动汽车驱动电机控制器主控芯片TMS320F28377S应用程序升级维护操作困难的问题,设计开发一种基于控制器局域网络(controller area network,CAN)通信技术的固件升级系统。通过配置CAN模块及Flash模块,解析HEX文件,结合汉明码校验算法,实现对引导程序及应用程序的设计;选用PyQt应用架构设计上位机操作界面,制定通信协议,实现对上位机软件的设计;在新能源汽车电机测试台架上,将开发的固件升级系统应用到电机控制器,进行电机电流加载闭环控制试验验证。试验结果表明:基于CAN通信的TMS320F28377S芯片固件升级系统能完成上位机和电机控制器的数据传输,系统快捷方便、稳定性高,可广泛应用于电机控制器应用程序的升级。展开更多
针对电动汽车电驱动系统中存在的关键技术问题,设计了基于CAN(controller area network)总线的电动汽车电驱动系统。系统由CAN通信模块和电机控制模块组成。CAN通信模块采用新型CAN总线收发器TJA1040和独立CAN控制器,并采用各种抗干扰...针对电动汽车电驱动系统中存在的关键技术问题,设计了基于CAN(controller area network)总线的电动汽车电驱动系统。系统由CAN通信模块和电机控制模块组成。CAN通信模块采用新型CAN总线收发器TJA1040和独立CAN控制器,并采用各种抗干扰措施以保证CAN通信的稳定性;控制模块利用模糊矢量控制方案——直接速度控制(direct speed control,DSC)策略,实现电驱动系统高鲁棒性控制。系统兼容性强,可以作为单独模块连接到电动汽车的主干网络上,还可以通过CAN总线对其进行扩展。展开更多
基金Supported by National Basic Research Program of China(973 Program)(Grant No.2015CB057302).
文摘Taylor–Couette–Poiseuille(TCP)flow dominates the inner water-cooling circulation of canned motor reactor coolant pumps.Current research on TCP flow focuses on torque behaviors and flow regime transitions through experiments and simulations.However,research on axial flow resistance in a large Reynolds number turbulent state is not sufficient,especially for the various flow patterns.This study is devoted to investigating the influence of annular flow on the axial flow resistance of liquid in the coaxial cylinders of the stator and rotor in canned motor reactor coolant pumps,and predicting the coolant flow distribution between the upper coil cooling loop and lower bearing lubricating loop for safe operation.The axial flow resistance,coupled with the annular rotation,is experimentally investigated at a flow rate with an axial Reynolds number,Rea,from 2.6×10~3 to 6.0×10~3 and rotational Reynolds number,Ret,from 1.6×10~4 to 4.0×10~4.It is revealed that the axial flow frictional coe cient varies against the axial flow rate in linear relation sets with logarithmic coordinates,which shift up when the flow has a higher Ret.Further examination of the axial flow resistance,with the Rea extending to 3.5×10~5 and Ret up to 1.6×10~5,by simulation shows gentle variation rates in the axial flow frictional coe cients against the Rea.The relation curves with different Ret values converge when the Rea exceeds 3.5×10~5.A prediction model for TCP flow consisting of a polygonal approximation with logarithmic coordinates is developed to estimate the axial flow resistance against different axial and rotational Reynolds numbers for the evaluation of heat and mass transfer during transition states and the engineering design of the canned motor chamber structure.
文摘In addition to the characteristics of a conventional motor, a novel direct-drive double-stator permanent-magnet brushless motor proposed can operate in the state of either a generator or a motor as appropriate. Through numerical calculation and analysis, the output torque of double-stator permanent-magnet brushless motor of the same volume as the traditional machine is discussed, and the reduction of torque ripple by using the structure features of this motor is investigated. The results indicate that lower torque ripple under the condition of ideal effective torque can be obtained by the rational design of motor. The prototype motors tested show that this kind of motor structure has a higher power density.
文摘A new-style direct drive motor with double-stator structure is proposed. The structure and principle of the permanent-magnet (PM) brushless motor are discussed. On the basis of numerical calculation, the cogging torque waveforms of the prototype motor when staggering two stators are analyzed. The method that can reduce torque ripple making use of the structure features of this motor is investigated. The results of numerical calculation and experiment indicate that designing motor with this kind of structure is a good scheme for increasing the power density.
文摘为解决电动汽车驱动电机控制器主控芯片TMS320F28377S应用程序升级维护操作困难的问题,设计开发一种基于控制器局域网络(controller area network,CAN)通信技术的固件升级系统。通过配置CAN模块及Flash模块,解析HEX文件,结合汉明码校验算法,实现对引导程序及应用程序的设计;选用PyQt应用架构设计上位机操作界面,制定通信协议,实现对上位机软件的设计;在新能源汽车电机测试台架上,将开发的固件升级系统应用到电机控制器,进行电机电流加载闭环控制试验验证。试验结果表明:基于CAN通信的TMS320F28377S芯片固件升级系统能完成上位机和电机控制器的数据传输,系统快捷方便、稳定性高,可广泛应用于电机控制器应用程序的升级。
文摘针对电动汽车电驱动系统中存在的关键技术问题,设计了基于CAN(controller area network)总线的电动汽车电驱动系统。系统由CAN通信模块和电机控制模块组成。CAN通信模块采用新型CAN总线收发器TJA1040和独立CAN控制器,并采用各种抗干扰措施以保证CAN通信的稳定性;控制模块利用模糊矢量控制方案——直接速度控制(direct speed control,DSC)策略,实现电驱动系统高鲁棒性控制。系统兼容性强,可以作为单独模块连接到电动汽车的主干网络上,还可以通过CAN总线对其进行扩展。
