Locally Enhanced Flow and Electric Fields Through a Tip Effect for Efficient Flow‑Electrode Capacitive Deionization

Low-electrode capacitive deionization(FCDI)is an emerging desalination technology with great potential for removal and/or recycling ions from a range of waters.However,it still suffers from inefficient charge transfer and ion transport kinetics due to weak turbulence and low electric intensity in flow electrodes,both restricted by the current collectors.Herein,a new tip-array current collector(designated as T-CC)was developed to replace the conventional planar current collectors,which intensifies both the charge transfer and ion transport significantly.The effects of tip arrays on flow and electric fields were studied by both computational simulations and electrochemical impedance spectroscopy,which revealed the reduction of ion transport barrier,charge transport barrier and internal resistance.With the voltage increased from 1.0 to 1.5 and 2.0 V,the T-CC-based FCDI system(T-FCDI)exhibited average salt removal rates(ASRR)of 0.18,0.50,and 0.89μmol cm^(-2) min^(-1),respectively,which are 1.82,2.65,and 2.48 folds higher than that of the conventional serpentine current collectors,and 1.48,1.67,and 1.49 folds higher than that of the planar current collectors.Meanwhile,with the solid content in flow electrodes increased from 1 to 5 wt%,the ASRR for T-FCDI increased from 0.29 to 0.50μmol cm^(-2) min^(-1),which are 1.70 and 1.67 folds higher than that of the planar current collectors.Additionally,a salt removal efficiency of 99.89%was achieved with T-FCDI and the charge efficiency remained above 95%after 24 h of operation,thus showing its superior long-term stability.

Enhancing capacitive deionization performance and cyclic stability of nitrogen-doped activated carbon by the electro-oxidation of anode materials

Electrode materials with high desalination capacity and long-term cyclic stability are the focus of capacitive deionization(CDI) community. Understanding the causes of performance decay in traditional carbons is crucial to design a high-performance material. Based on this, here, nitrogen-doped activated carbon(NAC) was prepared by pyrolyzing the blend of activated carbon powder(ACP) and melamine for the positive electrode of asymmetric CDI. By comparing the indicators changes such as conductivity, salt adsorption capacity, pH, and charge efficiency of the symmetrical ACP-ACP device to the asymmetric ACP-NAC device under different CDI cycles, as well as the changes of the electrochemical properties of anode and cathode materials after long-term operation, the reasons for the decline of the stability of the CDI performance were revealed. It was found that the carboxyl functional groups generated by the electro-oxidation of anode carbon materials make the anode zero-charge potential(E_(pzc)) shift positively,which results in the uneven distribution of potential windows of CDI units and affects the adsorption capacity. Furthermore, by understanding the electron density on C atoms surrounding the N atoms, we attribute the increased cyclic stability to the enhanced negativity of the charge of carbon atoms adjacent to quaternary-N and pyridinic-oxide-N.

Customized modulation on plasma uniformity by non-uniform magnetic field in capacitively coupled plasma

A two-dimensional fluid model based on COMSOL Multiphysics is developed to investigate the modulation of static magnetic field on plasma homogeneity in a capacitively coupled plasma(CCP)chamber. To generate a static magnetic field, direct current is applied to a circular coil located at the top of the chamber. By adjusting the magnetic field's configuration, which is done by altering the coil current and position, both the plasma uniformity and density can be significantly modulated. In the absence of the magnetic field, the plasma density exhibits an inhomogeneous distribution characterized by higher values at the plasma edge and lower values at the center. The introduction of a magnetic field generated by coils results in a significant increase in electron density near the coils. Furthermore, an increase in the sets of coils improves the uniformity of the plasma. By flexibly adjusting the positions of the coils and the applied current,a substantial enhancement in overall uniformity can be achieved. These findings demonstrate the feasibility of using this method for achieving uniform plasma densities in industrial applications.

Flexible capacitive pressure sensor based on interdigital electrodes with porous microneedle arrays for physiological signal monitoring

Flexible pressure sensors have many potential applications in the monitoring of physiological signals because of their good biocompatibil-ity and wearability.However,their relatively low sensitivity,linearity,and stability have hindered their large-scale commercial application.Herein,aflexible capacitive pressure sensor based on an interdigital electrode structure with two porous microneedle arrays(MNAs)is pro-posed.The porous substrate that constitutes the MNA is a mixed product of polydimethylsiloxane and NaHCO3.Due to its porous and interdigital structure,the maximum sensitivity(0.07 kPa-1)of a porous MNA-based pressure sensor was found to be seven times higher than that of an imporous MNA pressure sensor,and it was much greater than that of aflat pressure sensor without a porous MNA structure.Finite-element analysis showed that the interdigital MNA structure can greatly increase the strain and improve the sensitivity of the sen-sor.In addition,the porous MNA-based pressure sensor was found to have good stability over 1500 loading cycles as a result of its bilayer parylene-enhanced conductive electrode structure.Most importantly,it was found that the sensor could accurately monitor the motion of afinger,wrist joint,arm,face,abdomen,eye,and Adam’s apple.Furthermore,preliminary semantic recognition was achieved by monitoring the movement of the Adam’s apple.Finally,multiple pressure sensors were integrated into a 33 array to detect a spatial pressure distribu-×tion.Compared to the sensors reported in previous works,the interdigital electrode structure presented in this work improves sensitivity and stability by modifying the electrode layer rather than the dielectric layer.

Abnormal transition of the electron energy distribution with excitation of the second harmonic in low-pressure radio-frequency capacitively coupled plasmas

The self-excited second harmonic in radio-frequency capacitively coupled plasma was significantly enhanced by adjusting the external variable capacitor.At a lower pressure of 3 Pa,the excitation of the second harmonic caused an abnormal transition of the electron energy probability function,resulting in abrupt changes in the electron density and temperature.Such changes in the electron energy probability function as well as the electron density and temperature were not observed at the higher pressure of 16 Pa under similar harmonic changes.The phenomena are related to the influence of the second harmonic on stochastic heating,which is determined by both amplitude and the relative phase of the harmonics.The results suggest that the self-excited high-order harmonics must be considered in practical applications of lowpressure radio-frequency capacitively coupled plasmas.

Effect of a negative DC bias on a capacitively coupled Ar plasma operated at different radiofrequency voltages and gas pressures

The effect of a negative DC bias,|V_(dc)|,on the electrical parameters and discharge mode is investigated experimentally in a radiofrequency(RF)capacitively coupled Ar plasma operated at different RF voltage amplitudes and gas pressures.The electron density is measured using a hairpin probe and the spatio-temporal distribution of the electron-impact excitation rate is determined by phase-resolved optical emission spectroscopy.The electrical parameters are obtained based on the waveforms of the electrode voltage and plasma current measured by a voltage probe and a current probe.It was found that at a low|V_(dc)|,i.e.inα-mode,the electron density and RF current decline with increasing|V_(dc)|;meanwhile,the plasma impedance becomes more capacitive due to a widened sheath.Therefore,RF power deposition is suppressed.When|V_(dc)|exceeds a certain value,the plasma changes toα–γhybrid mode(or the discharge becomes dominated by theγ-mode),manifesting a drastically growing electron density and a moderately increasing RF current.Meanwhile,the plasma impedance becomes more resistive,so RF power deposition is enhanced with|V_(dc)|.We also found that the electrical parameters show similar dependence on|V_(dc)|at different RF voltages,andα–γmode transition occurs at a lower|V_(dc)|at a higher RF voltage.By increasing the pressure,plasma impedance becomes more resistive,so RF power deposition and electron density are enhanced.In particular,theα–γmode transition tends to occur at a lower|V_(dc)|with increase in pressure.

A Novel Capacitive Pressure Sensor

A novel capacitive pressure sensor is presented, whose sensing structure is a solid-state capacitor consisting of three square membranes with Al/SiO2/n-type silicon. It was fabricated using pn junction self-stop etching combined with adhesive bonding,and only three masks were used during the process. Sensors with side lengths of 1000,1200,and 1400μm were fabricated,showing sensitivity of 1.8,2.3, and 3.6fF/hPa over the range of 410～ 1010hPa, respectively. The sensi- tivity of the sensor with a side length of 1500μm is 4. 6fF/hPa,the nonlinearity is 6. 4% ,and the max hysteresis is 3.6%. The results show that permittivity change plays an important part in the capacitance change.

A Novel Capacitive Biaxial Microaccelerometer Based on the Slide-Film Damping Effect

A novel capacitive biaxial microaccelerometer with a highly symmetrical microstructure is developed. The sensor is composed of a single seismic mass, grid strip, supporting beam, joint beam, and damping adjusting combs. The sensing method of changing capacitance area is used in the design,which depresses the requirement of the DRIE process, and de- creases electronic noise by increasing sensing voltage to improve the resolution. The parameters and characteristics of the biaxial microaccelerometer are discussed with the FEM tool ANSYS. The simulated results show that the transverse sensitivity of the sensor is equal to zero. The testing devices based on the slide-film damping effect are fabricated, and the testing quality factor is 514, which shows that the designed structure can improve the resolution and proves the feasibility of the designed process.

Capacitive Microwave MEMS Switch

A novel capacitive microwave MEMS switch with a silicon/metal/dielectric as a membrane is fabricated successfully by bonding and etching-stop process. Its principal, design, and fabricating process are described in detail. A patterned dielectric layer, Ta2O5, with dielectric constant of 24 is reached. Experiment results show this novel structure,where the switch＇s dielectric layer is not prepared on the transmission line, features very low insertion loss. The insertion loss is 0.06dB at 2GHz and lower than 0.5dB in the wider range from De up to 20GHz,especially when the transmission line metal is only 0. 5μm thick.

CAPACITIVE DROP ANALYSER FOR MEASURING PHYSICAL PROPERTIES OF LIQUIDS

A new instrument called capacitive drop analyser (CDA) for measuring the physical properties of liquid is developed.A delivery head with a specialized wetting design was constructed for forming drops.The capacitive transducer uses the delivery head as one of its plates and a cylindrical ring plate.Excellent linearity is achieved by optimising the design,with an accuracy of drop volume measurement of approximately 2 μL.It is suitable for measuring both drops in equilibrium and those in the process of growing.Its capability of real time measurement makes it particularly useful for volatile liquids,in which instance the measurement of drop volume using a flowmeter or a pump is no longer reliable.The CDA can also be used to determine concentration.It is found that concentration curve is linear for aqueous glycerol solutions although not so for aqueous ethanol solution.The CDAs capability of measuring surface tension is also explored and experimental results are presented.

Development of Cd-doped Co Nanoparticles Encapsulated in Graphite Shell as Novel Electrode Material for the Capacitive Deionization Technology

Because of the low energy requirement and the environmentally safe byproducts, the capacitive deionization water desalination technology has attracted the attention of many researchers. The important requirements for electrode materials are good electrical conductivity, high surface area, good chemical stability and high specific capacitance. In this study, metallic nanoparticles that are encapsulated in a graphite shell(Cd doped Co/C NPs) are introduced as the new electrode material for the capacitive deionization process because they have higher specific capacitance than the pristine carbonaceous materials. Cd doped Co/C NPs perform better than graphene and the activated carbon. The introduced nanoparticles were synthesized using a simple sol gel technique. A typical sol gel composed of cadmium acetate, cobalt acetate and poly(vinyl alcohol)was prepared based on the polycondensation property of the acetates. The physiochemical characterizations that were used confirmed that the drying, grinding and calcination in an Ar atmosphere of the prepared gel produced the Cd doped Co nanoparticles, which were encapsulated in a thin graphite layer. Overall, the present study suggests a new method to effectively use the encapsulated bimetallic nanostructures in the capacitive deionization technology.

Flexible impedance and capacitive tensile load sensor based on CNT composite

In this paper, the fabrication and investigation of flexible impedance and capacitive tensile load sensors based on carbon nanotube（CNT） composite are reported. On thin rubber substrates, CNTs are deposited from suspension in water and pressed at elevated temperature. It is found that the fabricated load cells are highly sensitive to the applied mechanical force with good repeatability. The increase in impedance of the cells is observed to be 2.0 times while the decrease in the capacitance is found to be 2.1 times as applied force increases up to 0.3 N. The average impedance and capacitive sensitivity of the cell are equal to 3.4 N^（-1） and 1.8 N^（-1）, respectively. Experimental results are compared with the simulated values,and they show that they are in reasonable agreement with each other.

Frequency Matching Effects on Characteristics of Bulk Plasmas and Sheaths for Dual-Frequency Capacitively Coupled Argon Discharges: One-Dimensional Fluid Simulation

A one-dimensional fluid model is proposed to simulate the dual-frequency capacitively coupled plasma for Ar discharges. The influences of the low frequency on the plasma density, electron temperature, sheath voltage drop, and ion energy distribution at the powered electrode are investigated. The decoupling effect of the two radio-frequency sources on the plasma parameters, especially in the sheath region, is discussed in detail.

Capacitive Imaging Technique for the Inspection of Composite Sucker Rod

Composite sucker rod has been extensively used due to its high strength, light weight and corrosion resistive nature. However, such composite sucker rod is diffcult for conventional non-destructive evaluation(NDE) techniques to inspect because of its complex material and/or structure. It is thus useful to embark research on developing novel NDE technique to comply the inspection requirement. This work demonstrates the feasibility of using the capacitive imaging(CI) technique for the inspection of composite sucker rod. Finite element(FE) models were constructed in COMSOL to simulate the detection of defects in the glass-fiber layer and on the carbon core surface. An FE Model based inversion method is proposed to obtain the profile of the carbon core. Preliminary CI experimental results are then presented, including the detection of surface wearing defect in the glass-fiber layer, and obtaining the profile of the carbon core. A set of accelerated aging experiments were also carried out and the results indicate that the CI technique is potentially useful in evaluating the ageing status of such composite sucker rod. The CI technique described in this work shows great potential to target some challenging tasks faced in the non-destructive evaluation of composite sucker rod, including quality control, defect detection and ageing assessment.

Plasma Uniformity in a Dual Frequency Capacitively Coupled Plasma Reactor Measured by Optical Emission Spectroscopy

Local measurement of plasma radial uniformity was performed in a dual frequency capacitively coupled argon plasma （DF-CCP） reactor using an optical probe. The optical probe collects the light emission from a small separate volume in plasma, thus enabling to diagnose the plasma uniformity for different experimental parameters. Both the gas pressure and the low- frequency （LF） power have apparent effects on the radial uniformity of argon plasma. With the increase in either pressure or LF power, the emission profiles changed from a bell-shaped to a double-peak distribution. The influence of a fused-silica ring around the electrodes on the plasma uniformity was also studied using the optical probe. Possible reasons that result in nonuniform plasmas in our experiments are discussed.

Characteristics of dual-frequency capacitively coupled SF_6/O_2 plasma and plasma texturing of multi-crystalline silicon

Due to it being environmentally friendly, much attention has been paid to the dry plasma texturing technique serving as an alternative candidate for multicrystalline silicon （mc-Si） surface texturing. In this paper, capacitively coupled plasma （CCP） driven by a dual frequency （DF） of 40.68 MHz and 13.56 MHz is first used for plasma texturing of mc-Si with SF6/O2 gas mixture. Using a hairpin resonant probe and optical emission techniques, DF-CCP characteristics and their influence on mc-silicon surface plasma texturing are investigated at different flow rate ratios, pressures, and radio-frequency （RF） input powers. Experimental results show that suitable plasma texturing of mc-silicon occurs only in a narrow range of plasma parameters, where electron density ne must be larger than 6.3 x 109 cm-3 and the spectral intensity ratio of the F atom to that of the O atom （[F]/[O]） in the plasma must be between 0.8 and 0.3. Out of this range, no cone-like structure is formed on the mc-silicon surface. In our experiments, the lowest reflectance of about 7.3% for mc-silicon surface texturing is obtained at an [F]/[O] of 0.5 and ne of 6.9 × 109 cm-3.

PREPARATION OF CAPACITIVE-TYPE CO_2 GASSENSITIVE ELEMENT USING NANOMETER POWDERS

ＩＮＴＲＯＤＵＣＴＩＯＮＲｅｃｅｎｔｌｙ，ａｇｒｅａｔａｔｅｎｔｉｏｎｈａｓｂｅｅｎｐａｉｄｔｏｔｈｅｄｅｖｅｌｏｐｍｅｎｔａｎｄａｐｐｌｉｃａｔｉｏｎｏｆｅｎｖｉｒｏｎｍｅｎｔａｌｇａｓｓｅｎｓｏｒｓ［１－３］．Ｔｈｅｒｅｓｅａｒｃｈｅｓｏｎｓｏ...

Insights into Enhanced Capacitive Behavior of Carbon Cathode for Lithium Ion Capacitors: The Coupling of Pore Size and Graphitization Engineering

The lack of methods to modulate intrinsic textures of carbon cathode has seriously hindered the revelation of in-depth relationship between inherent natures and capacitive behaviors,limiting the advancement of lithium ion capacitors(LICs).Here,an orientateddesigned pore size distribution(range from 0.5 to 200 nm)and graphitization engineering strategy of carbon materials through regulating molar ratios of Zn/Co ions has been proposed,which provides an effective platform to deeply evaluate the capacitive behaviors of carbon cathode.Significantly,after the systematical analysis cooperating with experimental result and density functional theory calculation,it is uncovered that the size of solvated PF6-ion is about 1.5 nm.Moreover,the capacitive behaviors of carbon cathode could be enhanced attributed to the controlled pore size of 1.5-3 nm.Triggered with synergistic effect of graphitization and appropriate pore size distribution,optimized carbon cathode(Zn90Co10-APC)displays excellent capacitive performances with a reversible specific capacity of^50 mAh g-1at a current density of 5 A g-1.Furthermore,the assembly pre-lithiated graphite(PLG)//Zn90Co10-APC LIC could deliver a large energy density of 108 Wh kg-1 and a high power density of 150,000 W kg-1 as well as excellent long-term ability with 10,000 cycles.This elaborate work might shed light on the intensive understanding of the improved capacitive behavior in LiPF<sub>6 electrolyte and provide a feasible principle for elaborate fabrication of carbon cathodes for LIC systems.

Effective Modified Carbon Nanofibers as Electrodes for Capacitive Deionization Process

Carbon materials have the advantages of good electrical conductivity and excellent chemical stability, so many carbon materials have been introduced as electrodes for the capacitive deionization (CDI) process. Due to the low surface area compared to the other nanocarbonaceous materials, CNFs performance as electrode in the CDI units is comparatively low. This problem has been overcome by preparing high surface area carbon nanofibers and by creating numerous long pores on the nanofibers surface. The modified CNFs have been synthesized using low cost, high yield and facile method;electrospinning technique. Stabilization and graphitization of electrospun nanofiber mats composed of polyacrylonitrile (PAN) and poly (methyl methacrylate) (PMMA) leads form longitudinal pores CNFs. The utilized characterizations indicated that the CNFs obtained from electrospun solution having 50% PMMA have surface area of 181 m2/g which are more than the conventional CNFs. Accordingly, these nanofibers revealed salt removal efficiency of ~90% and specific capacitance of 237 F/g.

Capacitive charge storage enables an ultrahigh cathode capacity in aluminum-graphene battery

Aluminum^-graphene battery is promising for its abundant raw materials,high power density,ultralong cycle life and superior safety.However,the development of aluminum^-graphene battery is currently restricted by its insufficient cathode capacity,calling for a newly developed working mechanism.In addition,an irregular constant increase of the cathode capacity was always observed during cycling,but cannot be explained based on the current understanding.Here,we observed an increase of specific capacity by 60%with stable Coulombic efficiency of 98%during 7000 cycles life of Al-graphene batteries employing AlCl3/ET3NHCl electrolyte.We demonstrated this growing cathode capacity is attributed to an increasing contribution of capacitive charge storage during cycling,because a gradually enlarged surface area as capacitive active sites is enabled by the exfoliation of graphitic cathode during the periodic intercalation process.Moreover,the graphene cathode was exfoliated more significantly in AlCl3/ET3NHCl than 1-ethyl-3-methylimidazolium chloride-based electrolyte,which results from the heavier stress on the graphene layers caused by the larger intercalants in AlCl3/ET3NHCl.The common intercalation of cations with AlCl4-clusters was therefore supposed to occur during charging.This new proposed mechanism can offer the new thought for future design on high-capacity cathode of Al-ion battery.