Simultaneous recovery of carbon and sulfur resources from reduction of CO_2 with H_2S using catalysts

An approach to the simultaneous reclamation of carbon and sulfur resources from CO2 and H2S has been proposed and effectively implemented with the aid of catalysts. A brief thermodynamic study reveals the potential of direct reduction of CO2 with H2S（15：15 mol% balanced with N2） for selective production of CO and elemental sulfur. The experiments carried out in a fixed-bed flow reactor over the temperature range of 400–800 °C give evidence of the importance of the employment of catalysts. Both the conversions of the reactants and the selectivities of the target products can be substantially promoted over most catalysts studied. Nevertheless, little difference appears among their catalytic performance. The results also prove that the presence of CO2 can remarkably enhance H2S conversion and the sulfur yield in comparison with H2S direct decomposition. A longtime reaction test on Mg O catalyst manifests its superior durability at high temperature（700 °C） and huge gas hourly space velocity（100,000 h-1）. Free radicals initiated by catalysts are supposed to dominate the reactions between CO2 and H2S.

Coupled thermo-hydro-mechanical simulation of CO2 enhanced gas recovery with an extended equation of state module for TOUGH2MP-FLAC3D

As one of the most important ways to reduce the greenhouse gas emission,carbon dioxide（CO2）enhanced gas recovery（CO2-EGR） is attractive since the gas recovery can be enhanced simultaneously with CO2sequestration.Based on the existing equation of state（EOS） module of TOUGH2 MP,extEOS7C is developed to calculate the phase partition of H2O-CO2-CH4-NaCl mixtures accurately with consideration of dissolved NaCI and brine properties at high pressure and temperature conditions.Verifications show that it can be applied up to the pressure of 100 MPa and temperature of 150℃.The module was implemented in the linked simulator TOUGH2MP-FLAC3 D for the coupled hydro-mechanical simulations.A simplified three-dimensional（3D）1/4 model（2.2 km×1 km×1 km） which consists of the whole reservoir,caprock and baserock was generated based on the geological conditions of a gas field in the North German Basin.The simulation results show that,under an injection rate of 200,000 t/yr and production rate of 200,000 sm3/d,CO2breakthrough occurred in the case with the initial reservoir pressure of 5 MPa but did not occur in the case of 42 MPa.Under low pressure conditions,the pressure driven horizontal transport is the dominant process;while under high pressure conditions,the density driven vertical flow is dominant.Under the considered conditions,the CO2-EGR caused only small pressure changes.The largest pore pressure increase（2 MPa） and uplift（7 mm） occurred at the caprock bottom induced by only CO2injection.The caprock had still the primary stress state and its integrity was not affected.The formation water salinity and temperature variations of ±20℃ had small influences on the CO2-EGR process.In order to slow down the breakthrough,it is suggested that CO2-EGR should be carried out before the reservoir pressure drops below the critical pressure of CO2.

Optimum Development of a Saturated Oil Field

This project investigated the potential optimal development strategy for a saturated reservoir, with a gas cap. It assessed the viability of three production methods—solution gas drive (primary depletion), water flooding and gas injection, using varying injector well numbers. This project also undertook sensitivity analysis in the field, concluding that the development of another appraisal well would vastly improve the accuracy of NPV calculation. Furthermore, this project ascertained an optimized recovery method, based on numerical production simulations and economic modelling, of initial solution gas drive recovery, until reservoir pressure equals the bubble point pressure, at which point three water flooding injectors should be employed, developed at six-month intervals to maximise production while limiting CAPEX and OPEX as much as possible.

Recovery of silica from sodium silicate solution of calcined boron mud

The effect of several parameters on the recovery of silicon dioxide from calcined boron mud（CBM）such as stirring speed, temperature, sodium silicate concentration, and carbonation time was studied. The recovery of silicon dioxide is 88 % when the stirring speed is450 r min-1, temperature is 60 °C, sodium silicate concentration is 1 mol L-1, and the carbonation time is 6 h.The effect of carbonation time on the recovery of silicon dioxide is divided into three kinetic regimes, and the carbonation process of sodium silicate solution follows a second-order reaction based on the double-film theory model. The apparent rate constant of the three kinetic regimes is 0.064, 3.178, and 1.130 L h mol-1, respectively.The amorphous SiO_2 products obtained by carbonating the purified solution have 99.6 % purity and are spherical with diameters of about 100 nm.