In this paper, the effects of test temperatures and time on the impact damage behavior of unidirectional carbon fiber reinforced epoxy resin composites, immersed in pure water, on a pendulum impact tester, was studied...In this paper, the effects of test temperatures and time on the impact damage behavior of unidirectional carbon fiber reinforced epoxy resin composites, immersed in pure water, on a pendulum impact tester, was studied. The results show that immersion in liquids has a significant effect on the impact resistance of the unidirectional composite material. It is obvious that after immersion, the mass of the material increases. The fracture initiation forces as well as the fracture initiation energy decrease as the immersion time lengthens. Moreover, the higher the temperature and the longer the time are, the more the crack propagation energy and the ductility index will be. Immersion makes the fracture mode change from the dominant fiber fracture into dominant delamination. All in all, immersion decreases the impact resistance of the composites and causes the fracture mode to change.展开更多
We put forward a method of fabricating Aluminum(Al)/carbon fibers(CFs) composite sheets by the accumulative roll bonding(ARB) method. The finished Al/CFs composite sheet has CFs and pure Al sheets as sandwich and surf...We put forward a method of fabricating Aluminum(Al)/carbon fibers(CFs) composite sheets by the accumulative roll bonding(ARB) method. The finished Al/CFs composite sheet has CFs and pure Al sheets as sandwich and surface layers. After cross-section observation of the Al/CFs composite sheet, we found that the CFs discretely distributed within the sandwich layer. Besides, the tensile test showed that the contribution of the sandwich CFs layer to tensile strength was less than 11% compared with annealed pure Al sheet. With ex-situ observation of the CFs breakage evolution with-16%,-32%, and-45% rolling reduction during the ARB process, the plastic instability of the Al layer was found to bring shear damages to the CFs. At last, the bridging strengthening mechanism introduced by CFs was sacrificed. We provide new insight into and instruction on Al/CFs composite sheet preparation method and processing parameters.展开更多
To meet the requirements of spacecraft for the thermal conductivity of resins and solve the problem of low thermal conduction efficiency when 3D printing complex parts,we propose a new type of continuous mesophase-pit...To meet the requirements of spacecraft for the thermal conductivity of resins and solve the problem of low thermal conduction efficiency when 3D printing complex parts,we propose a new type of continuous mesophase-pitch-based carbon fiber/thermoplastic polyurethane/epoxy(CMPCF/TPU/epoxy)composite filament and its preparation process in this study.The composite filament is based on the high thermal conductivity of CMPCF,the high elasticity of TPU,and the high-temperature resistance of epoxy.The tensile strength and thermal conductivity of the CMPCF/TPU/epoxy composite filament were tested.The CMPCF/TPU/epoxy composites are formed by 3D printing technology,and the composite filament is laid according to the direction of heat conduction so that the printed part can meet the needs of directional heat conduction.The experimental results show that the thermal conductivity of the printed sample is 40.549 W/(m·K),which is 160 times that of pure epoxy resin(0.254 W/(m·K)).It is also approximately 13 times better than that of polyacrylonitrile carbon fiber/epoxy(PAN-CF/epoxy)composites.This study breaks through the technical bottleneck of poor printability of CMPCF.It provides a new method for achieving directional thermal conductivity printing,which is important for the development of complex high-performance thermal conductivity products.展开更多
This work aims at investigating the microwave absorption and mechanical properties of short-cutted carbon fiber/glass fiber hybrid veil reinforced epoxy composites.The short-cutted carbon fibers(CFs)/glass fibers(GFs)...This work aims at investigating the microwave absorption and mechanical properties of short-cutted carbon fiber/glass fiber hybrid veil reinforced epoxy composites.The short-cutted carbon fibers(CFs)/glass fibers(GFs)hybrid veil were prepared by papermaking technology,and composites liquid molding was employed to manufacture CFs/GFs hybrid epoxy composites.The microstructure,microwave absorbing properties and mechanical properties of the hybrid epoxy composites were studied by using SEM,vector network analyzer and universal material testing,respectively.The reflection coefficient of the composites were calculated by the measured complex permittivity and permeability in the X-band(8.2-12.4 GHz)range.The optimum microwave absorption properties can be obtained when the content of CFs in the hybrid veil is 6 wt%and the thickness of the composites is 2 mm,the minimum reflection coefficient of-31.8 dB and the effective absorption bandwidth is 2.1 GHz,which is ascribed to benefitting impedance matching characteristic and dielectric loss of the carbon fiber.Simultaneously the tensile strength and modulus can achieve 104.0 and 2.98GPa,demonstrating that the CFs/GFs hybrid epoxy composites can be a promising candidate of microwave absorbing materials with high mechanical properties.展开更多
In this study,the durability of a new polymer carbonfiber-reinforced epoxy resin used to produce composite material in the aerospacefield is investigated through analysis of the corrosion phenomena occurring at the micr...In this study,the durability of a new polymer carbonfiber-reinforced epoxy resin used to produce composite material in the aerospacefield is investigated through analysis of the corrosion phenomena occurring at the microscopic scale,and the related infrared spectra and thermal properties.It is found that light and heat can con-tribute to the aging process.In particular,the longitudinal tensile strength displays a non-monotonic trend,i.e.,itfirst increases and then decreases over time.By contrast,the longitudinal compressive and inter-laminar shear strengths do not show significant changes.It is also shown that the inter-laminar shear strength of carbonfiber/epoxy resin composites with inter-laminar hybrid structure is better than that of pure carbonfiber materials.The related resistance to corrosion can be improved by more than 41%.展开更多
The residual resources of ramie fiber-based textile products were used as raw materials.Ramie fiber felt(RF)was modified by NaClO_(2) aqueous solution and then impregnated with water-based epoxy resin(WER).RF/WER tran...The residual resources of ramie fiber-based textile products were used as raw materials.Ramie fiber felt(RF)was modified by NaClO_(2) aqueous solution and then impregnated with water-based epoxy resin(WER).RF/WER transparent composite materials were prepared by lamination hot pressing process.The composite materials’color difference,transmittance,haze,density,water absorption,and mechanical properties were determined to assess the effects of NaClO_(2) treatment and the number of ramie fiber layers on the properties of the prepared composites.The results showed significantly improved optical and mechanical properties of the RF/WER transparent composites after NaClO_(2) treatment.With the increase of ramie fiber layers,the composites’whiteness,transmittance,and water absorption decreased while the haze increased.For material with three layers,the optical transmittance in the visible light region was 82%,and the haze was 96%,indicating the material has both high transmittance and high haze characteristics.The tensile strength increases with the increase of the number of layers,and the tensile strength of the composite with six layers is 243 MPa.This study broadens the scope of application of ramie fiber as a new option for home decoration materials.展开更多
The morphological structure of various epoxies toughened with a special amorphous thermoplastic PEK C and their carbon fiber composites were studied by using SEM. For both cases, phase separation and inversion took pl...The morphological structure of various epoxies toughened with a special amorphous thermoplastic PEK C and their carbon fiber composites were studied by using SEM. For both cases, phase separation and inversion took place to form fine epoxy rich globules dispersing in the PEK C matrix, in which the epoxy rich phase had the absolutely higher volume fraction. The phase structure and the interfacial properties were also studied by means of FTIR, DSC, and DMTA as well. An accompanying mechanical determination revealed that an improved toughness was achieved both in the blend casts and in the carbon fiber composites. A composite structural model was hence suggested.展开更多
In this study,two types of soluble thermoplastic resins were added to epoxy resin at a fixed weight ratio to prepare a three-phase cast body.The cast was then manufactured into hybrid nanofiber as interleaves for inte...In this study,two types of soluble thermoplastic resins were added to epoxy resin at a fixed weight ratio to prepare a three-phase cast body.The cast was then manufactured into hybrid nanofiber as interleaves for interlaminar toughening of carbon fiber/epoxy resin(CF/EP)composites using a co-solvent method.The results revealed that when the hybrid components reached 15 wt%,Polyethersulfone(PES)and polyaryletherketone cardo(PEK-C)exhibited the best synergistic toughening effect,and the fracture toughness increased by 99.8%and 39.8%,respectively,compared with the reference or the same proportion of the single PES toughened sample.We used PES/PEK-C hybrid nanofibers with an areal density of 19.2 g per square meter(gsm)as composite toughening layers.Apart from the lack of significant influence of PES nanofiber on CF/EP composites,the interlaminar fracture toughness of mode I and mode II layers increased by 88.3%and 46.9%,respectively,compared to the reference sample.Scanning Electron Microscopy of the fracture surface and cross-section micromorphology of the laminate displayed that the thermoplastic microspheres of different sizes contribute differently to crack resistance:PEK-C consumes more energy due to the debonding and extraction of microspheres and resin,whereas the presence of the PES phase can induce more plastic deformation and crack deflection.展开更多
Microwave processing was used to cure the carbon fiber/epoxy composites and designed for improving the compressive strength of the materials. By controlling the power of microwave heating, vacuum bagged laminates were...Microwave processing was used to cure the carbon fiber/epoxy composites and designed for improving the compressive strength of the materials. By controlling the power of microwave heating, vacuum bagged laminates were fabricated under one atmosphere pressure without arcing. The physical and mechanical properties of composites produced through vacuum bagging using microwave and thermal curing were compared and the multistep(2-step or 3-step) microwave curing process for improved compressive properties was established. The results indicated that microwave cured samples had somewhat differentiated molecular structure and showed slightly higher glass transition temperature. The 2-step process was found to be more conducive to the enhancement of the compressive strength than the 3-step process. A 39% cure cycle time reduction and a 22% compressive strength increment were achieved for the composites manufactured with microwave radiation. The improvement in specific compressive strength was attributed to better interfacial bonding between resin matrix and the fibers, which was also demonstrated via scanning electron microscopy analysis.展开更多
In order to enhance the interfacial adhesion of carbon fiber(CF)and polymer matrix,a multiscale gradient modulus intermediate layer with rigid-flexible(GO-PA)hierarchical structure was designed and fabricated between ...In order to enhance the interfacial adhesion of carbon fiber(CF)and polymer matrix,a multiscale gradient modulus intermediate layer with rigid-flexible(GO-PA)hierarchical structure was designed and fabricated between CFs and matrix by a facile and businesslike strategy.The polarity,roughness and wettability of CFs surface as well as the thickness of intermediate layer in composite have been significantly increased after rigid-flexible hierarchical structure was constructed.The IFSS,ILSS,compression and impact toughness manifested that the hierarchical structure could bring about a fantastic improvement(76.8%,46.4%,40.7%and 37.8%)for the interfacial and mechanical properties than other previous reports.Consequently,the establishment of CF surface with gradient modulus rigid-flexible hierarchical structure via regulation of nanoparticles and polymer array would open a new,viable and promising route to obtaining high-performance composites.展开更多
To determinate the water diffusion coefficients and dynamics in adhesive/carbon fiber reinforced epoxy resin composite joints,energy dispersive X-ray spectroscopy analysis(EDX)is used to establish the content change o...To determinate the water diffusion coefficients and dynamics in adhesive/carbon fiber reinforced epoxy resin composite joints,energy dispersive X-ray spectroscopy analysis(EDX)is used to establish the content change of oxygen in the adhesive in adhesive/carbon fiber reinforced epoxy resin composite joints.As water is made up of oxygen and hydrogen,the water diffusion coefficients and dynamics in adhesive/carbon fiber reinforced epoxy resin composite joints can be obtained from the change in the content of oxygen in the adhesive during humidity aging,via EDX analysis.The authors have calculated the water diffusion coefficients and dynamics in the adhesive/carbon fiber reinforced epoxy resin composite joints with the aid of both energy dispersive X-ray spectroscopy and elemental analysis.The determined results with EDX analysis are almost the same as those determined with elemental analysis and the results also show that the durability of the adhesive/carbon fiber reinforced epoxy resin composite joints subjected to silane coupling agent treatment is better than those subjected to sand paper burnishing treatment and chemical oxidation treatment.展开更多
Microwave absorption (MWA) materials such as graphene nanoplatelet (GNP)/epoxy are mostly used as coatings on existing structures without considering mechanical properties. In this work, we aim to enhance the mechanic...Microwave absorption (MWA) materials such as graphene nanoplatelet (GNP)/epoxy are mostly used as coatings on existing structures without considering mechanical properties. In this work, we aim to enhance the mechanical strength of the composite for multifunctional potentials. We used carbon fiber (four layers) to reinforce GNP/epoxy composite (2 mm thick) and investigated their multifunctional properties with GNP loading from 3 to 7 wt%. We measured the tensile strength, hardness, and MW absorption (26.5 - 40 GHz) of composite samples. Our results showed an increase in tensile strength to 109.1 ± 7.9 MPa with 7 wt% GNP in the composite from 15.3 MPa for pure epoxy. The hardness of the composites was also substantially enhanced with GNP loading up to 7 wt%. A MW absorption ratio of 72% was attained for the sample with 7 wt% GNP loading near 40 GHz. The homogenous dispersion of GNPs in the matrix reduces the stress concentration and minimizes the influence of the defects. The high MW absorption and large transmission loss together with enhanced mechanical strength provides a novel multifunctional material for potential applications.展开更多
Microwave processing has great potential for improving composite manufacturing such as reduction of curing time, energy requirements and operational costs. In this paper, the effects of microwave irradiation for resin...Microwave processing has great potential for improving composite manufacturing such as reduction of curing time, energy requirements and operational costs. In this paper, the effects of microwave irradiation for resin-curing of carbon fiber/epoxy resin composite that was composed of discontinuous carbon fibers of 130 μm or 3 mm were investigated. The mechanical properties of carbon fiber/epoxy resin composite cured by microwave irradiation for 20 min at 120°C were similar to ones of the sample prepared by conventional oven for 180 min at 120°C. Microwavecured carbon fiber/epoxy resin composite had higher glass transition temperature than the one prepared by conventional oven. The relation between curing time and flexural modulus indicated that the curing velocity of microwave-irradiated carbon fiber/epoxy resin composite was 9 times faster than the one prepared by conventional oven. Furthermore, activation energies for resincuring reaction on microwave and conventional-cured carbon fiber/epoxy resin composite were estimated. The resin-curing reaction in carbon fiber/epoxy resin composite was promoted by microwave irradiation.展开更多
Carbon fiber reinforced polymer(CFRP)composites with high load-bearing capacity are currently ideal materials in tribological load systems.One of the unique features during the friction process of CFRP/metal is the in...Carbon fiber reinforced polymer(CFRP)composites with high load-bearing capacity are currently ideal materials in tribological load systems.One of the unique features during the friction process of CFRP/metal is the in-situ formation of an ultrathin and uniform transfer film on the metal surface,and the related initial/transfer mechanism is very important but still unclear.Recent studies mainly focus on the one-way transfer process of CFRP to the metal surface,that is,forward transfer;whereas another easily overlooked issue is that the metal material also transfers backward to the CFRP surface.Herein,we firstly prepared carbon fiber/epoxy resin composites(CF/EP)by the hot-pressing method and then carried out friction tests with iron alloy as the control material.The underlying mechanism of the forward/backward transfer process is revealed by controlling the morphological evolution and iron content of the transfer film on worn CF/EP.According to the variation law of friction coefficient with time,the interfacial friction is divided into three different stages,among which the behaviours of“micro-convex contact”and“epoxy exfoliation”occur throughout the whole procedure.We believe this work could provide a meaningful reference for studying the friction behaviour and mechanism,especially the forward and backward transfer between composites/metals,and further broaden its emerging applications in future energy,aerospace and rail transportation.展开更多
The fracture toughness of carbon fiber reinforced epoxy composite(CFRP)was investigated through mode I and mode II shaped fracture system in this paper.A novel polyimide with trifluoromethyl groups and grafted nanosil...The fracture toughness of carbon fiber reinforced epoxy composite(CFRP)was investigated through mode I and mode II shaped fracture system in this paper.A novel polyimide with trifluoromethyl groups and grafted nanosilica were used to modify epoxy resin.Effect of modified resin and unmodified resin on fracture toughness of CFRP was compared and discussed.Lay-up angles and thicknesses effects on fracture toughness of composites were also investigated.The fracture toughness of CFRP was obtained through double cantilever beam(DCB)and end notched flexure(ENF)tests.The results showed that the composites prepared by modified resin exhibited high fracture toughness compared with unmodified composites.The fracture toughness value of mode I increased from 1.83 kJ/m2 to 4.55 kJ/m2.The fracture toughness value of mode II increased from 2.30 kJ/m2 to 6.47 kJ/m2.展开更多
An analysis of a booster arm made of a carbon fiber reinforced epoxy composite material is conducted by means of a finite element analysis method.The mechanical properties are also determined through stretching and co...An analysis of a booster arm made of a carbon fiber reinforced epoxy composite material is conducted by means of a finite element analysis method.The mechanical properties are also determined through stretching and compression performance tests.It is found that the surface treatment of the fibers causes the silane coupling agent to undergo a chemical reaction on the surface of the glass fiber.The used material succeeds in producing significant vibrations damping(vibration attenuation effect is superior to that obtained with conventional alloy materials).展开更多
Composite materials may be composed of several types of fiber and resin.The design of hybrid composites intends to improve the physico-mechanical properties of this kind of materials,compared to standard composites,wh...Composite materials may be composed of several types of fiber and resin.The design of hybrid composites intends to improve the physico-mechanical properties of this kind of materials,compared to standard composites,which consist of epoxy resin matrixes and carbon fibers,which presents low impact resistance.Our goal was the development and characterization of a hybrid material composed of two kinds of fibers,carbon and Kevlar,in the fabric format,joined by epoxy resin matrix.The standard composition is the Composition 1:containing 55%-60%carbon fiber and 40%-45%epoxy resin.The hybrid composite is the Composition 2:that contains 30%-33%carbon fiber,25%-27%Kevlar fiber and 40%-45%of epoxy resin.The composite plates were prepared using a laminator machine and later they were process in a vacuum bag and cured in oven.The study aimed at comparing the physical and mechanical properties of these materials.The mechanical tests were focus on measurements of the tensile,flexural and impact charpy stresses,and physics tests by measures of bulk densities.Through these procedures,we hope to find out data that may be useful for a partial characterization of these products for applications in the aerospace industry.展开更多
Damage caused due to low-velocity impacts in composites leads to substantial deterioration in their residual strength and eventually provokes structural failure.This work presents an experimental investigation on the ...Damage caused due to low-velocity impacts in composites leads to substantial deterioration in their residual strength and eventually provokes structural failure.This work presents an experimental investigation on the effects of different patch and parent laminate stacking sequences on the enhancement of impact strength of Carbon Fiber Reinforced Polymers(CFRP)composites by utilising the adhesively bonded external patch repair technique.Damage evolution study is also performed with the aid of Acoustic Emission(AE).Two different quasi-isotropic configurations were selected for the parent laminate,viz.,[45°/45°/0°/0°]s and[45°/0°/45°/0°]s.Quasi Static Indentation(QSI)test was performed on both the pristine laminates,and damage areas were detected by using the C-scan inspection technique.Damaged laminates were repaired by using a single-sided patch of two different configurations,viz.,[45°/45°/45°/45°]and[45°/0°/0°/45°],and employing a circular plug to fill the damaged hole.Four different combinations of repaired laminates with two configurations of each parent and patch laminate were produced,which were further subjected to the QSI test.The results reveal the effectiveness of the repair method,as all the repaired laminates show higher impact resistance compared to the respective pristine laminates.Patches of[45°/0°/0°/45°]configuration when repaired by taking[45°/45°/0°/0°]s and[45°/0°/45°/0°]s as parents exhibited 68%and 73%higher peak loads,respectively,than the respective pristine laminates.Furthermore,parent and patch of configuration[45°/0°/45°/0°]s and[45°/0°/0°/45°],respectively,attain the highest peak load,whereas[45°/45°/0°/0°]s and[45°/45°/45°/45°]combinations possess the most gradual decrease in the load.展开更多
Machining damage occurs on the surface of carbon fiber reinforced polymer (CFRP) composites during processing. In the current simulation model of CFRP, the initial defects on the carbon fiber and the periodic random d...Machining damage occurs on the surface of carbon fiber reinforced polymer (CFRP) composites during processing. In the current simulation model of CFRP, the initial defects on the carbon fiber and the periodic random distribution of the reinforcement phase in the matrix are not considered in detail, which makes the characteristics of the cutting model significantly different from the actual processing conditions. In this paper, a novel three-phase model of carbon fiber/cyanate ester composites is proposed to simulate the machining damage of the composites. The periodic random distribution of the carbon fiber reinforced phase in the matrix was realized using a double perturbation algorithm. To achieve the stochastic distribution of the strength of a single carbon fiber, a novel method that combines the Weibull intensity distribution theory with the Monte Carlo method is presented. The mechanical properties of the cyanate matrix were characterized by fitting the stress-strain curves, and the cohesive zone model was employed to simulate the interface. Based on the model, the machining damage mechanism of the composites was revealed using finite element simulations and by conducting a theoretical analysis. Furthermore, the milling surfaces of the composites were observed using a scanning electron microscope, to verify the accuracy of the simulation results. In this study, the simulations and theoretical analysis of the carbon fiber/cyanate ester composite processing were carried out based on a novel three-phase model, which revealed the material failure and machining damage mechanism more accurately.展开更多
The main problems with the liquid-phase technology of carbon fiber/aluminum matrix composites include poor wetting of the fiber with liquid aluminum and formation of aluminum carbide on the fibers’surface.This paper ...The main problems with the liquid-phase technology of carbon fiber/aluminum matrix composites include poor wetting of the fiber with liquid aluminum and formation of aluminum carbide on the fibers’surface.This paper aims to solve these problems.The theoretical and experimental dependence of porosity on the applied pressure were determined.The possibility of obtaining a carbon fiber/aluminum matrix composite wire with a strength value of about 1500 MPa was shown.The correlation among the strength of the carbon fiber reinforced aluminum matrix composite,the fracture surface,and the degradation of the carbon fiber surface was discussed.展开更多
基金aeronautical Science Foundation of China(04A51011)
文摘In this paper, the effects of test temperatures and time on the impact damage behavior of unidirectional carbon fiber reinforced epoxy resin composites, immersed in pure water, on a pendulum impact tester, was studied. The results show that immersion in liquids has a significant effect on the impact resistance of the unidirectional composite material. It is obvious that after immersion, the mass of the material increases. The fracture initiation forces as well as the fracture initiation energy decrease as the immersion time lengthens. Moreover, the higher the temperature and the longer the time are, the more the crack propagation energy and the ductility index will be. Immersion makes the fracture mode change from the dominant fiber fracture into dominant delamination. All in all, immersion decreases the impact resistance of the composites and causes the fracture mode to change.
基金Supported by Innovation and Technology Fund (No.ITP/045/19AP)Commercial Research&Development (CRD) Funding Supported by Hong Kong Productivity Council (No.10008787)。
文摘We put forward a method of fabricating Aluminum(Al)/carbon fibers(CFs) composite sheets by the accumulative roll bonding(ARB) method. The finished Al/CFs composite sheet has CFs and pure Al sheets as sandwich and surface layers. After cross-section observation of the Al/CFs composite sheet, we found that the CFs discretely distributed within the sandwich layer. Besides, the tensile test showed that the contribution of the sandwich CFs layer to tensile strength was less than 11% compared with annealed pure Al sheet. With ex-situ observation of the CFs breakage evolution with-16%,-32%, and-45% rolling reduction during the ARB process, the plastic instability of the Al layer was found to bring shear damages to the CFs. At last, the bridging strengthening mechanism introduced by CFs was sacrificed. We provide new insight into and instruction on Al/CFs composite sheet preparation method and processing parameters.
基金supported by the National Natural Science Foundation of China(Nos.52175474 and 52275498)。
文摘To meet the requirements of spacecraft for the thermal conductivity of resins and solve the problem of low thermal conduction efficiency when 3D printing complex parts,we propose a new type of continuous mesophase-pitch-based carbon fiber/thermoplastic polyurethane/epoxy(CMPCF/TPU/epoxy)composite filament and its preparation process in this study.The composite filament is based on the high thermal conductivity of CMPCF,the high elasticity of TPU,and the high-temperature resistance of epoxy.The tensile strength and thermal conductivity of the CMPCF/TPU/epoxy composite filament were tested.The CMPCF/TPU/epoxy composites are formed by 3D printing technology,and the composite filament is laid according to the direction of heat conduction so that the printed part can meet the needs of directional heat conduction.The experimental results show that the thermal conductivity of the printed sample is 40.549 W/(m·K),which is 160 times that of pure epoxy resin(0.254 W/(m·K)).It is also approximately 13 times better than that of polyacrylonitrile carbon fiber/epoxy(PAN-CF/epoxy)composites.This study breaks through the technical bottleneck of poor printability of CMPCF.It provides a new method for achieving directional thermal conductivity printing,which is important for the development of complex high-performance thermal conductivity products.
基金Funded by Key Research and Development Plan in Hubei Province of China(Nos.2022BCA082,2022BCA077,2021BCA153)Initial Scientific Research Fund for High-level Talents of Hubei University of Technology(No.GCRC2020017)。
文摘This work aims at investigating the microwave absorption and mechanical properties of short-cutted carbon fiber/glass fiber hybrid veil reinforced epoxy composites.The short-cutted carbon fibers(CFs)/glass fibers(GFs)hybrid veil were prepared by papermaking technology,and composites liquid molding was employed to manufacture CFs/GFs hybrid epoxy composites.The microstructure,microwave absorbing properties and mechanical properties of the hybrid epoxy composites were studied by using SEM,vector network analyzer and universal material testing,respectively.The reflection coefficient of the composites were calculated by the measured complex permittivity and permeability in the X-band(8.2-12.4 GHz)range.The optimum microwave absorption properties can be obtained when the content of CFs in the hybrid veil is 6 wt%and the thickness of the composites is 2 mm,the minimum reflection coefficient of-31.8 dB and the effective absorption bandwidth is 2.1 GHz,which is ascribed to benefitting impedance matching characteristic and dielectric loss of the carbon fiber.Simultaneously the tensile strength and modulus can achieve 104.0 and 2.98GPa,demonstrating that the CFs/GFs hybrid epoxy composites can be a promising candidate of microwave absorbing materials with high mechanical properties.
文摘In this study,the durability of a new polymer carbonfiber-reinforced epoxy resin used to produce composite material in the aerospacefield is investigated through analysis of the corrosion phenomena occurring at the microscopic scale,and the related infrared spectra and thermal properties.It is found that light and heat can con-tribute to the aging process.In particular,the longitudinal tensile strength displays a non-monotonic trend,i.e.,itfirst increases and then decreases over time.By contrast,the longitudinal compressive and inter-laminar shear strengths do not show significant changes.It is also shown that the inter-laminar shear strength of carbonfiber/epoxy resin composites with inter-laminar hybrid structure is better than that of pure carbonfiber materials.The related resistance to corrosion can be improved by more than 41%.
基金supported by the National Natural Science Foundation of China (No.32171882)the Science and Technology Innovation Program of Hunan Province of China (2021RC4062)Scientific Research Project of Hunan Provincial Department of Education (20K143).
文摘The residual resources of ramie fiber-based textile products were used as raw materials.Ramie fiber felt(RF)was modified by NaClO_(2) aqueous solution and then impregnated with water-based epoxy resin(WER).RF/WER transparent composite materials were prepared by lamination hot pressing process.The composite materials’color difference,transmittance,haze,density,water absorption,and mechanical properties were determined to assess the effects of NaClO_(2) treatment and the number of ramie fiber layers on the properties of the prepared composites.The results showed significantly improved optical and mechanical properties of the RF/WER transparent composites after NaClO_(2) treatment.With the increase of ramie fiber layers,the composites’whiteness,transmittance,and water absorption decreased while the haze increased.For material with three layers,the optical transmittance in the visible light region was 82%,and the haze was 96%,indicating the material has both high transmittance and high haze characteristics.The tensile strength increases with the increase of the number of layers,and the tensile strength of the composite with six layers is 243 MPa.This study broadens the scope of application of ramie fiber as a new option for home decoration materials.
文摘The morphological structure of various epoxies toughened with a special amorphous thermoplastic PEK C and their carbon fiber composites were studied by using SEM. For both cases, phase separation and inversion took place to form fine epoxy rich globules dispersing in the PEK C matrix, in which the epoxy rich phase had the absolutely higher volume fraction. The phase structure and the interfacial properties were also studied by means of FTIR, DSC, and DMTA as well. An accompanying mechanical determination revealed that an improved toughness was achieved both in the blend casts and in the carbon fiber composites. A composite structural model was hence suggested.
基金The project was funded by State Key Laboratory for Modification of Chemical Fibers and Polymer Materials,Donghua University(no.KF2121)Science and Technology Tackle Key Project of Henan Province(no.212102210036)+1 种基金Science and Technology Tackle Key Project of Henan Province(no.212102210550)the Science and Technology Guidance Project of China National Textile and Apparel Council(no.2020061).
文摘In this study,two types of soluble thermoplastic resins were added to epoxy resin at a fixed weight ratio to prepare a three-phase cast body.The cast was then manufactured into hybrid nanofiber as interleaves for interlaminar toughening of carbon fiber/epoxy resin(CF/EP)composites using a co-solvent method.The results revealed that when the hybrid components reached 15 wt%,Polyethersulfone(PES)and polyaryletherketone cardo(PEK-C)exhibited the best synergistic toughening effect,and the fracture toughness increased by 99.8%and 39.8%,respectively,compared with the reference or the same proportion of the single PES toughened sample.We used PES/PEK-C hybrid nanofibers with an areal density of 19.2 g per square meter(gsm)as composite toughening layers.Apart from the lack of significant influence of PES nanofiber on CF/EP composites,the interlaminar fracture toughness of mode I and mode II layers increased by 88.3%and 46.9%,respectively,compared to the reference sample.Scanning Electron Microscopy of the fracture surface and cross-section micromorphology of the laminate displayed that the thermoplastic microspheres of different sizes contribute differently to crack resistance:PEK-C consumes more energy due to the debonding and extraction of microspheres and resin,whereas the presence of the PES phase can induce more plastic deformation and crack deflection.
基金the Innovation Funds of China-National Engineering and Research Center for Commercial Aircraft Manufacturing (SAMC12-JS-15-015) for financial support
文摘Microwave processing was used to cure the carbon fiber/epoxy composites and designed for improving the compressive strength of the materials. By controlling the power of microwave heating, vacuum bagged laminates were fabricated under one atmosphere pressure without arcing. The physical and mechanical properties of composites produced through vacuum bagging using microwave and thermal curing were compared and the multistep(2-step or 3-step) microwave curing process for improved compressive properties was established. The results indicated that microwave cured samples had somewhat differentiated molecular structure and showed slightly higher glass transition temperature. The 2-step process was found to be more conducive to the enhancement of the compressive strength than the 3-step process. A 39% cure cycle time reduction and a 22% compressive strength increment were achieved for the composites manufactured with microwave radiation. The improvement in specific compressive strength was attributed to better interfacial bonding between resin matrix and the fibers, which was also demonstrated via scanning electron microscopy analysis.
基金the National Natural Science Foundation of China(Nos.51803102 and 51903129)Natural Science Foundation of Shandong Province(Nos.201807070028 and 201808220020)+2 种基金the Source Innovation Project of Qingdao(No.19-6-2-75-cg)Industry and Education Cooperation Program of The Ministry of Education(Nos.201802201002,201901078008 and 201802230009)Opening Project of Shanxi Province Key Laboratory of Functional Nanocomposites,North University of China(No.NFCM202001).
文摘In order to enhance the interfacial adhesion of carbon fiber(CF)and polymer matrix,a multiscale gradient modulus intermediate layer with rigid-flexible(GO-PA)hierarchical structure was designed and fabricated between CFs and matrix by a facile and businesslike strategy.The polarity,roughness and wettability of CFs surface as well as the thickness of intermediate layer in composite have been significantly increased after rigid-flexible hierarchical structure was constructed.The IFSS,ILSS,compression and impact toughness manifested that the hierarchical structure could bring about a fantastic improvement(76.8%,46.4%,40.7%and 37.8%)for the interfacial and mechanical properties than other previous reports.Consequently,the establishment of CF surface with gradient modulus rigid-flexible hierarchical structure via regulation of nanoparticles and polymer array would open a new,viable and promising route to obtaining high-performance composites.
基金Supported by Commission of Science Technology and Industry for National Defense of China(No.JPPT-115-477).
文摘To determinate the water diffusion coefficients and dynamics in adhesive/carbon fiber reinforced epoxy resin composite joints,energy dispersive X-ray spectroscopy analysis(EDX)is used to establish the content change of oxygen in the adhesive in adhesive/carbon fiber reinforced epoxy resin composite joints.As water is made up of oxygen and hydrogen,the water diffusion coefficients and dynamics in adhesive/carbon fiber reinforced epoxy resin composite joints can be obtained from the change in the content of oxygen in the adhesive during humidity aging,via EDX analysis.The authors have calculated the water diffusion coefficients and dynamics in the adhesive/carbon fiber reinforced epoxy resin composite joints with the aid of both energy dispersive X-ray spectroscopy and elemental analysis.The determined results with EDX analysis are almost the same as those determined with elemental analysis and the results also show that the durability of the adhesive/carbon fiber reinforced epoxy resin composite joints subjected to silane coupling agent treatment is better than those subjected to sand paper burnishing treatment and chemical oxidation treatment.
文摘Microwave absorption (MWA) materials such as graphene nanoplatelet (GNP)/epoxy are mostly used as coatings on existing structures without considering mechanical properties. In this work, we aim to enhance the mechanical strength of the composite for multifunctional potentials. We used carbon fiber (four layers) to reinforce GNP/epoxy composite (2 mm thick) and investigated their multifunctional properties with GNP loading from 3 to 7 wt%. We measured the tensile strength, hardness, and MW absorption (26.5 - 40 GHz) of composite samples. Our results showed an increase in tensile strength to 109.1 ± 7.9 MPa with 7 wt% GNP in the composite from 15.3 MPa for pure epoxy. The hardness of the composites was also substantially enhanced with GNP loading up to 7 wt%. A MW absorption ratio of 72% was attained for the sample with 7 wt% GNP loading near 40 GHz. The homogenous dispersion of GNPs in the matrix reduces the stress concentration and minimizes the influence of the defects. The high MW absorption and large transmission loss together with enhanced mechanical strength provides a novel multifunctional material for potential applications.
文摘Microwave processing has great potential for improving composite manufacturing such as reduction of curing time, energy requirements and operational costs. In this paper, the effects of microwave irradiation for resin-curing of carbon fiber/epoxy resin composite that was composed of discontinuous carbon fibers of 130 μm or 3 mm were investigated. The mechanical properties of carbon fiber/epoxy resin composite cured by microwave irradiation for 20 min at 120°C were similar to ones of the sample prepared by conventional oven for 180 min at 120°C. Microwavecured carbon fiber/epoxy resin composite had higher glass transition temperature than the one prepared by conventional oven. The relation between curing time and flexural modulus indicated that the curing velocity of microwave-irradiated carbon fiber/epoxy resin composite was 9 times faster than the one prepared by conventional oven. Furthermore, activation energies for resincuring reaction on microwave and conventional-cured carbon fiber/epoxy resin composite were estimated. The resin-curing reaction in carbon fiber/epoxy resin composite was promoted by microwave irradiation.
基金supported by the Natural Science Foundation of Guangdong Province,China (Grant No. 2021B1515020087)the National Natural Science Foundation of China (Grant No. 51775197)。
文摘Carbon fiber reinforced polymer(CFRP)composites with high load-bearing capacity are currently ideal materials in tribological load systems.One of the unique features during the friction process of CFRP/metal is the in-situ formation of an ultrathin and uniform transfer film on the metal surface,and the related initial/transfer mechanism is very important but still unclear.Recent studies mainly focus on the one-way transfer process of CFRP to the metal surface,that is,forward transfer;whereas another easily overlooked issue is that the metal material also transfers backward to the CFRP surface.Herein,we firstly prepared carbon fiber/epoxy resin composites(CF/EP)by the hot-pressing method and then carried out friction tests with iron alloy as the control material.The underlying mechanism of the forward/backward transfer process is revealed by controlling the morphological evolution and iron content of the transfer film on worn CF/EP.According to the variation law of friction coefficient with time,the interfacial friction is divided into three different stages,among which the behaviours of“micro-convex contact”and“epoxy exfoliation”occur throughout the whole procedure.We believe this work could provide a meaningful reference for studying the friction behaviour and mechanism,especially the forward and backward transfer between composites/metals,and further broaden its emerging applications in future energy,aerospace and rail transportation.
基金National Natural Science Foundation of China(No.11802192)Natural Science Foundation of Jiangsu Province,China(No.BK20180244)Nantong Science and Technology Project,China(No.JC2019012)。
文摘The fracture toughness of carbon fiber reinforced epoxy composite(CFRP)was investigated through mode I and mode II shaped fracture system in this paper.A novel polyimide with trifluoromethyl groups and grafted nanosilica were used to modify epoxy resin.Effect of modified resin and unmodified resin on fracture toughness of CFRP was compared and discussed.Lay-up angles and thicknesses effects on fracture toughness of composites were also investigated.The fracture toughness of CFRP was obtained through double cantilever beam(DCB)and end notched flexure(ENF)tests.The results showed that the composites prepared by modified resin exhibited high fracture toughness compared with unmodified composites.The fracture toughness value of mode I increased from 1.83 kJ/m2 to 4.55 kJ/m2.The fracture toughness value of mode II increased from 2.30 kJ/m2 to 6.47 kJ/m2.
基金This work was financially supported by Scientific Research Fund of Yunnan Institute of Engineering(2019gchy01).
文摘An analysis of a booster arm made of a carbon fiber reinforced epoxy composite material is conducted by means of a finite element analysis method.The mechanical properties are also determined through stretching and compression performance tests.It is found that the surface treatment of the fibers causes the silane coupling agent to undergo a chemical reaction on the surface of the glass fiber.The used material succeeds in producing significant vibrations damping(vibration attenuation effect is superior to that obtained with conventional alloy materials).
文摘Composite materials may be composed of several types of fiber and resin.The design of hybrid composites intends to improve the physico-mechanical properties of this kind of materials,compared to standard composites,which consist of epoxy resin matrixes and carbon fibers,which presents low impact resistance.Our goal was the development and characterization of a hybrid material composed of two kinds of fibers,carbon and Kevlar,in the fabric format,joined by epoxy resin matrix.The standard composition is the Composition 1:containing 55%-60%carbon fiber and 40%-45%epoxy resin.The hybrid composite is the Composition 2:that contains 30%-33%carbon fiber,25%-27%Kevlar fiber and 40%-45%of epoxy resin.The composite plates were prepared using a laminator machine and later they were process in a vacuum bag and cured in oven.The study aimed at comparing the physical and mechanical properties of these materials.The mechanical tests were focus on measurements of the tensile,flexural and impact charpy stresses,and physics tests by measures of bulk densities.Through these procedures,we hope to find out data that may be useful for a partial characterization of these products for applications in the aerospace industry.
基金the financial support by the Council of Scientific&Industrial Research(CSIR)-Research Scheme,India(22/0809/2019-EMR-II)。
文摘Damage caused due to low-velocity impacts in composites leads to substantial deterioration in their residual strength and eventually provokes structural failure.This work presents an experimental investigation on the effects of different patch and parent laminate stacking sequences on the enhancement of impact strength of Carbon Fiber Reinforced Polymers(CFRP)composites by utilising the adhesively bonded external patch repair technique.Damage evolution study is also performed with the aid of Acoustic Emission(AE).Two different quasi-isotropic configurations were selected for the parent laminate,viz.,[45°/45°/0°/0°]s and[45°/0°/45°/0°]s.Quasi Static Indentation(QSI)test was performed on both the pristine laminates,and damage areas were detected by using the C-scan inspection technique.Damaged laminates were repaired by using a single-sided patch of two different configurations,viz.,[45°/45°/45°/45°]and[45°/0°/0°/45°],and employing a circular plug to fill the damaged hole.Four different combinations of repaired laminates with two configurations of each parent and patch laminate were produced,which were further subjected to the QSI test.The results reveal the effectiveness of the repair method,as all the repaired laminates show higher impact resistance compared to the respective pristine laminates.Patches of[45°/0°/0°/45°]configuration when repaired by taking[45°/45°/0°/0°]s and[45°/0°/45°/0°]s as parents exhibited 68%and 73%higher peak loads,respectively,than the respective pristine laminates.Furthermore,parent and patch of configuration[45°/0°/45°/0°]s and[45°/0°/0°/45°],respectively,attain the highest peak load,whereas[45°/45°/0°/0°]s and[45°/45°/45°/45°]combinations possess the most gradual decrease in the load.
基金Supported by Research Innovation Fund Project “Research on micro machining mechanism of fiber reinforced composites”(Grant No.HIT.NSRIF.2014055)of Harbin Institute of Technology,China
文摘Machining damage occurs on the surface of carbon fiber reinforced polymer (CFRP) composites during processing. In the current simulation model of CFRP, the initial defects on the carbon fiber and the periodic random distribution of the reinforcement phase in the matrix are not considered in detail, which makes the characteristics of the cutting model significantly different from the actual processing conditions. In this paper, a novel three-phase model of carbon fiber/cyanate ester composites is proposed to simulate the machining damage of the composites. The periodic random distribution of the carbon fiber reinforced phase in the matrix was realized using a double perturbation algorithm. To achieve the stochastic distribution of the strength of a single carbon fiber, a novel method that combines the Weibull intensity distribution theory with the Monte Carlo method is presented. The mechanical properties of the cyanate matrix were characterized by fitting the stress-strain curves, and the cohesive zone model was employed to simulate the interface. Based on the model, the machining damage mechanism of the composites was revealed using finite element simulations and by conducting a theoretical analysis. Furthermore, the milling surfaces of the composites were observed using a scanning electron microscope, to verify the accuracy of the simulation results. In this study, the simulations and theoretical analysis of the carbon fiber/cyanate ester composite processing were carried out based on a novel three-phase model, which revealed the material failure and machining damage mechanism more accurately.
基金financially supported by ISSP RAS-Russian Government contracts
文摘The main problems with the liquid-phase technology of carbon fiber/aluminum matrix composites include poor wetting of the fiber with liquid aluminum and formation of aluminum carbide on the fibers’surface.This paper aims to solve these problems.The theoretical and experimental dependence of porosity on the applied pressure were determined.The possibility of obtaining a carbon fiber/aluminum matrix composite wire with a strength value of about 1500 MPa was shown.The correlation among the strength of the carbon fiber reinforced aluminum matrix composite,the fracture surface,and the degradation of the carbon fiber surface was discussed.