Flow Injection Amperometric Determination of Phenol and Chlorophenols at Single Wall Carbon Nanotube Modified Glassy Carbon Electrode

Single wall carbon nanotube modified glassy carbon electrode (SWCNT/GCE) was used for flow-injection analysis (FIA) for phenolic compounds (phenol (P), 4-chlorophenol (CP), 2,4-dichlorophenol (DCP), 2,4,6-trichlorphenol (TCP) and pentachlorophenol (PCP)). Experimental variables such as the detection potential, flow rate and pH of the carrier solution, 0.1 M sodium acetate, were optimized. Under these conditions, the designed electrode showed a very good performance for the amperometric measurements, with no need to apply a cleaning or pre-treatment procedure. The operational stability was tested with 20 repetitive injections of each analyte and was found to be good. The analytical performance of the SWCNT/GCE electrode under flow through conditions was tested and was found to be impressive. When it is compared with other enzymatic and non-enzymatic sensors, it shows wider dynamic range for the detection of phenolic compounds with low limits of detection. These results suggest that the method is quite useful for monitoring and analyzing phenols and chlorophenols.

A Glassy Carbon Electrode Modified with Cellulose Nanofibrils from Ammophila arenaria for the Sensitive Detection of L-Trytophan

L-tryptophan is an essential amino acid for human health. Nanofibrillated cellulose (NFC) from marram grass (Ammophila arenaria) extracted from plants harvested in the center of Tunisia was used for the first time for the modification of a glassy carbon electrode (GCE), for the sensitive detection of L-tryptophan (Trp). After spectroscopic and morphological characterization of the extracted NFC, the GC electrode modification was monitored through cyclic voltammetry. The NFC-modified electrode exhibited good analytical performance in detecting Trp with a wide linear range between 7.5 × 10−4 mM and 10−2 mM, a detection limit of 0.2 µM, and a high sensitivity of 140.0 µA∙mM−1. Additionally, the NFC/GCE showed a good reproducibility, good selectivity versus other amino acids, uric acid, ascorbic acid, and good applicability to the detection of Trp in urine samples.

Direct Electrochemical Oxidation of NADPH at a Low Potential on the Carbon Nanotube Modified Glassy Carbon Electrode

NADPH can be directly oxidized on a carbon nanotube modified glassy carbon (CNT/GC) electrode in phosphate buffer solution (pH=6.0) with a diminution of the overpotential of more than 700 mV. The anodic peak currents increase linearly with the increase of concentration of NADPH in the range of 5 x 10(-7) to 1 x 10(-3) mol/L with a detection limit of about 1 x 10-7 mol/L. The CNT/GC electrode exhibits high sensitivity, low potential and stability in detecting NADPH and thus might be used in biosensors to study the electrocatalytic reaction of important dehydrogenase-based biological systems.

Glassy carbon electrode modified with multi-walled carbon nanotubes sensor for the quantihication of antihistamine drug pheniramine in solubilized systems

A sensitive electroanalytical method for quantification of pheniramine in pharmaceutical formulation has been investigated on the basis of the enhanced electrochemical response at glassy carbon electrode modified with multi-walled carbon nanotubes in the presence of sodium lauryl sulfate.The experimental results suggest that the phcniramine in anionic surfactant solution exhibits electrocatalytic effect resulting in a marked enhancement of the peak current response.Peak current response is linearly dependent on the concentration of pheniramine in the range 200-1500 μg/mL with correlation coefficient 0.9987.The limit of detection is 58.31 μg/m L.The modified electrode shows good sensitivity and repeatability.

Voltammetric Response of Epinephrine at Carbon Nanotube Modified Glassy Carbon Electrode and Activated Glassy Carbon Electrode

The electrochemical behavior of epinephrine at activated glassy carbon electrode and carbon nanotube-coated glassy carbon electrode was studied. Epinephrine could exhibit an anodic peak at about 0.2 V （vs. SCE） at bare glassy carbon electrode, but it was very small. However, when the electrode was activated at certain potential （i.e. 1.9 V） or modified with carbon nanotube, the peak became more sensitive, resulting from the increase in electrode area in addition to the electrostatic attraction. Under the selected conditions, the anodic peak current was linear to epinephrine concentration in the range of 3.3×10^-7 - 1.1×10^-5 mol/L at activated glassy carbon electrode and in the range of 1.0×10^-5 - 5.0×10^-5 mol/L at carbon nanotube-coated electrode. The correlation coefficients were 0.998 and 0.997, respectively. The determination limit was 1.0×10^-7 mol/L. The two electrodes have been successfully applied for the determination of epinephrine in adrenaline hydrochloride injection with recovery of 95%-104%.

Direct Electrochemistry of Catalase on Single Wall Carbon Nanotubes Modified Glassy Carbon Electrode

Direct electrochemistry of catalase (Ct) has been studied on single wall carbon nanotubes (SWNTs) modified glassy carbon (GC) electrode. A pair of well-defined nearly reversible redox peaks is given at –0.48 V (vs. SCE) in 0.1 mol/L phosphate solution (pH 7.0). The peak current in cyclic voltammogram is proportional to the scan rate. The peak potential of catalase is shifted to more negative value when the pH increases. Catalase can adsorb on the SWNTs modified electrode.

A Functionalized Multi-walled Carbon Nanotube and Gold Nanoparticle Composite-modified Glassy Carbon Electrode for the Detection of Enterovirus 71

Hand, foot, and mouth disease (HFMD) is a common infectious disease in children, occurring primarily in preschool children[1_3] with infants under three years old being gen erally susceptible. The disease is caused by various enteroviruses, among which EV71 and Coxsackievirus A group 16 (Cox A16) are the most comm on ⑷.According to in formation released by the Chinese Center for Disease Control and Prevention on June 8, 2016, EV71 infection- related HFMD has been prevalent among infants and young children in China since 2007, with a high incidenee and many deaths.

Electrochemical Determination of Reduced Glutathione at Multiwalled Carbon Nanotubes/Poly(bromocresol green) Modified Glassy Carbon Electrode

A multiwalled carbon nanotubes/poly(bromocresol green) modfied glassy carbon electrode (MWNTs-PBG/GCE) was used to investigate the electrochemical behavior of reduced glutathione(GSH). GSH showed an irreversible oxidation process on MWNTs-PBG/GCE with an oxidation peak at 0.77 V(vs. SCE) in a phosphate buffer solution(pH=4.0). The kinetic parameters of the electrochemical behavior of GSH on MWNTs-PBG/GCE were calculated. Under the optimal conditions and with the help of amperometric method, a linear relationship was obtained between the oxidation peak current and GSH concentration in the range from 2×10-7 mol/L to 5×10-6 mol/L with the detection limit as 1×10-8 mol/L(signal-to-noise ratio of 3). The current reached the steady-state current within about 5 s. The modified electrode surface had very good reproducibility and stability.

Enhanced performance of solution-processed carbon nanotube transparent electrodes in foldable perovskite solar cells through vertical separation of binders by using eco-friendly parylene substrate

The successful utilization of an eco-friendly and biocompatible parylene-C substrate for high-performance solution-processed double-walled carbon nanotube(CNT)electrode-based perovskite solar cells(PSCs)was demonstrated.Through the use of a novel inversion transfer technique,vertical separation of the binders from the CNTs was induced,rendering a stronger p-doping effect and thereby a higher conductivity of the CNTs.The resulting foldable devices exhibited a power conversion efficiency of 18.11%,which is the highest reported among CNT transparent electrode-based PSCs to date,and withstood more than 10,000 folding cycles at a radius of 0.5 mm,demonstrating unprecedented mechanical stability.Furthermore,solar modules were fabricated using entirely laser scribing processes to assess the potential of the solution-processable nanocarbon electrode.Notably,this is the only one to be processed entirely by the laser scribing process and to be biocompatible as well as eco-friendly among the previously reported nonindium tin oxide-based perovskite solar modules.

Study of enzyme biosensor based on carbon nanotubes modified electrode for detection of pesticides residue

The paper describes a controllable layer-by-layer （LBL） self-assembly modification technique of multi-walled carbon nanotubes （MWNTs） and poly（diallyldimethylammonium chloride） （PDDA） towards glassy carbon electrode （GCE）, Acetylcholinesterase （ACHE） was immobilized directly to the modified GCE by LBL self-assembly method, the activity value of AChE was detected by using i-t technique based on the modified Ellman method. Then the composition of carbaryl were detected by the enzyme electrode with 0.01U activity value and the detection limit of carbaryl is 10^- 12 g L ^-1 so the enzyme biosensor showed good properties for pesticides residue detection.

New modified multiwalled carbon nanotubes paste electrode for electrocatalytic oxidation and determination of warfarin in biological and pharmaceutical samples

A novel sensor for the determination of warfarin based on a simple and sensitive method was developed on multiwalled-carbon-nanotube modified ZnCrFeO4 carbon paste electrodes（MWCNT/ZnCrFeO4/CPEs）. Cyclic voltammetry, differential pulse voltammetry, chronoamperometry, and electrochemical impedance spectroscopy were used to investigate the electrochemical behavior of warfarin at the chemically modified electrode. According to the results, MWCNT/ZnCrFeO4/CPEs showed high electrocatalytic activity for warfarin oxidation, producing a sharp oxidation peak current at about ＋0.97 vs Ag/AgCl reference electrode at pH = 4.0. The peak current was linearly dependent on warfarin concentration over the range of 0.02–920.0 μmol/L with a detection limit of 0.003 μmol/L. In addition, chronoamperometry was also used to determine warfarin＇s catalytic rate constant and diffusion coefficient at MWCNT/ZnCrFeO4/CPEs.

Determination of captopril in patient human urine using ferrocenemonocarboxylic acid modified carbon nanotubes paste electrode

In this work,we describe a new strategy for the electrochemical determination of captopril（CA） using ferrocenemonocarboxylic acid as a mediator and multiwall carbon nanotubes as sensors in aqueous solution at pH 7.0.The diffusion coefficient（D）,and the kinetic parameters such as electron transfer coefficient（α）.and heterogeneous rate constant（kh）,for CA were also determined using electrochemical approaches.Under the optimized conditions,the electrocatalytic oxidation peak current of captopril showed two linear dynamic ranges with a detection limit of 0.3×10^-6 mol L^-1 captopril.The linear calibration range was 0.8×10^（-6） to 65×10^-6 mol L^-1 using cyclic voltammetry.Finally,this modified electrode was also examined as a selective,simple and precise new electrochemical sensor for the determination of captopril in real samples such as drug and patient human urine.

Voltammetric sensor based on cobalt-poly(methionine)-modified glassy carbon electrode for determination of estriol hormone in pharmaceuticals and urine

A voltammetric sensor based on the electropolymerization of cobalt-poly(methionine)(Co-poly(Met)) on a glassy carbon electrode (GCE) was developed and applied for the determination of estriol by differential pulse voltammetry (DPV) for the first time. The electrochemical properties of the Co-poly(Met)/GCE were analysed by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were used to characterize the polymers on the GCE surface. The deposition of the Co-poly(Met) film on the GCE surface enhanced the sensor electronic transfer. CV studies revealed that estriol exhibits an irreversible oxidation peak at t0.58 V for the Co-poly(Met)/GCE (vs. Ag/AgCl reference electrode) in 0.10 mol/L Britton-Robinson buffer solution (pH=7.0). Different voltammetric scan rates (10-200 mV/s) suggested that the estriol oxidation on the Co-poly(Met)/GCE surface is controlled by adsorption and diffusion processes. Based on the optimized DPV conditions, the linear responses for estriol quantification were from 0.596 μmol/L to 4.76 μmol/L (R2 =0.996) and from 5.66 μmol/L to 9.90 μmol/L (R2 =0.994) with a limit of detection (LOD) of 0.0340 μmol/L and a limit of quantification (LOQ) of 0.113 μmol/L. The DPV-Co-poly(Met)/GCE method provided good intra-day and inter-day repeatability with RSD values lower than 5%. Also, no interference of real sample matrices was observed on the estriol voltammetric response, making the DPV-Copoly( Met)/GCE highly selective for estriol. The accuracy test showed that the estriol recovery was in the ranges 96.7%-103% and 98.7%-102% for pharmaceutical tablets and human urine, respectively. The estriol quantification in pharmaceutical tablets performed by the Co-poly(Met)/GCE-assisted DPV method was comparable to the official analytical protocols.

Determination of 6-Mercaptopurine in Rat Blood by Microdialysis Coupled with High Performance Liquid Chromatography on a Functionalized Multi-wall Carbon Nanotubes Modified Electrode

A new chemically modified electrode(CME) immobilized on the surface of multi-wall carbon nanotubes functionalized with carboxylic groups was fabricated. The results indicate that the CME exhibits efficiently electrocatalytic oxidation of 6-mercaptopurine(6-MP). The CME can be used as the working electrode in the liquid chromatography for the determination of 6-MP. The peak current of 6-MP is linearly changed with its concentration ranging from 4.0×10 -7 to 1.0×10 -4 mol/L with the calculated detection limit (S/N=3) of 2.0×10 -7 mol/L. Coupled with microdialysis sampling, the method has been successfully applied to assessing the content of 6-MP in rat blood.

Electrooxidation of Nitric Oxide at a Glass Carbon Electrode Modified with Functionalized Single-walled Carbon Nanotube

The electrocatalytic oxidation of nitric oxide（NO） at a glass carbon electrode（GC） modified with functionalized single-walled carbon nanotubes（SWCNTs） was investigated by cyclic voltammetry（CV） and electrochemical impedance spectroscopy（EIS）.It was found that the SWCNT modified electrode could speed greatly up the electron transfer rate compared with the bare GC electrode.After the SWCNT was treated with alkali or mixed acids,the reaction rate and activation energy of NO electrooxidation were changed to different extent.Chemical modification of the SWCNT surface is one of the most powerful methods to change the sensitivity of NO electrooxidation reaction.The modified electrode with SWCNT obtained by the firstly alkali treatment and then the mixed acids treatment was the best one for NO electrooxidation,the result of CV was also confirmed by that of EIS.The anodic processes of NO were recognized more clearly by exploring the reaction mechanism of NO electrooxidation at the SWCNT modified electrode.

Cyclic Voltammetry Determination of Epinephrine with a Nano-gold Modified Glassy Carbon Electrode in the Presence of High Concentration Ascorbic Acid

Nano-gold (NG) modified glassy carbon electrodes (GCEs) were used for determination of epinephrine (EP) in the presence of high concentration ascorbic acid (AA) by cyclic voltammetry (CV). This modified electrode can not only catalytically oxidize EP and AA, but also separate the catalytic peak potentials of EP and AA by about 183.5 mV. In pH = 7.0 ogisogate byffer solution, the linear range of epinephrine was 5 106 ~ 1 ?10-4 mol/L.

Direct Electrochemistry and Electrocatalysis of Hemoglobin at PAMAM Dendrimer-MWNTs-Au Nanoparticles Composite Film Modified Glassy Carbon Electrode

The direct electron transfer of hemoglobin at the PAMAM-MWNTs-AuNPs composite film modified glassy carbon electrode was studied. In a phosphate buffer solution（PBS, pH=7.0）, the formal potential（E^0） of Hb was -0.105 V versus SCE, the electron transfer rate constant was 4.66 s-1. E^0＇ of Hb at the modified electrode was linearly varied in a pH range of 5.0-8.0 with a slope of-49.2 mV/pH. The Hb/PAMAM-MWNTs-AuNPs/GCE gave an excellent electrocatalytic response to the reduction of hydrogen peroxide. The catalytic current increased linearly with H2O2 concentration in a range of 1.0× 10^-6 to 2.2× 10^-3 mol/L. The detection limit was 2.0× 10^-7 mol/L at a signal to noise ratio of 3. The Michaelis-Menten constant（Km^app） was 2.95 mmol/L.

Sensitive voltammetric determination of xanthinol nicotinate at a carbon nanotubes-ionic liquid gel modified electrode

The electrochemistry of xanthinol nicotinate （Xan） was studied by cyclic voltammetry at a glassy carbon electrode modified by a gel containing multi-walled carbon nanotubes （MWNTs） and room-temperature ionic liquid of 1-butyl-3-methylimidazolium hexafluorophosphate （BMIMPF6）. The modified electrode exhibited good promotion to the electrochemical oxidation of Xan and an ultrasensitive electrochemical method was proposed for the determination of Xan. This method was successfully applied to the determination of Xan in Xan tablets. C 2009 XiaoYu Bao. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.

Voltammetric Response and Electrocatalysis of Glassy Carbon Electrode Modified with Monolayer Nickel Hydroxide

The glassy carbon (GC) electrode modified with a monolayer nickel hydroxide (GC/Ni(OH) 2) was prepared by immersion of GC substrate in 1.0×10 -3 mol/L NiSO 4 solution, and then cyclic voltammetric scanning in 0.20 mol/L KOH. Similarly, GC/Co(OH) 2 electrode was prepared too. The experiments showed that the voltammetric behavior of GC/Ni(OH) 2 electrode in 0.20 mol/L KOH is more stable than that of GC/ Co(OH) 2. It was found that the GC/Ni(OH) 2 electrode acts as an effective electrocatalysis for the oxidation of hydrazine.

Gold Nanoparticle-based Layer-by-Layer Enhancement of DNA Hybridization Electrochemical Signal at Carbon Nanotube Modified Carbon Paste Electrode

Colloid gold nanoparticle-based layer-by-layer amplification approach was applied to enhance the electrochemical detection sensitivity of DNA hybridization at carbon nanotube modified carbon paste electrodes （CNTPEs）. Streptavidin was immobilized onto the surface of CNTPEs, and the conjugation of biotin labeled target oligonucle,otides to the above immobilized streptavidin was performed, followed by the hybridization of target oligonucleotides with the gold nanoparticle-labeled DNA probe and then the layer-by-layer enhanced connection of gold nanoparticles, on which oligonucleotides complementary to the DNA probe were attached, to the hybridization system. The differential pulse voltammetry （DPV） signal of total gold nanoparticles was monitored. It was found that the layer-by-layer colloidal gold DPV detection enhanced the sensitivity by about one order of magnitude compared with that of one-layer detection. One-base mismatched DNA and complementary DNA could be distinguished clearly.