Preparation and Analysis of Carbon Fiber-Silicon Carbide Thermally Conductive Asphalt Concrete

An experimental investigation into the thermal conductivity of CF-SiC two-phase composite asphalt concrete is presented.The main objective of this study was to verify the possibility of using SiC powder instead of mineral powder as the thermal conductive filler to prepare a new type of asphalt concrete and improve the efficiency of electrothermal snow and ice melting systems accordingly.The thermal conductivity of asphalt concrete prepared with different thermally conductive fillers was tested by a transient plane source method,and the related performances were measured.Then the temperature rise rate and surface temperature were studied through field heating tests.Finally,the actual ice melting efficiency of the thermally conductive asphalt concrete was evaluated using an effective electrothermal system.As shown by the experimental results,the composite made of SiC powder and carbon fiber has a high thermal conductivity.When SiC replaces mineral powder,the thermal conductivity of the asphalt mixture increases first and then decreases with the increase of carbon fiber content.In the present study,in particular,the thermal conductivity attained a peak when the carbon fiber content was 0.2%of the aggregate mass.

Research Progress of Carbon-Silicone Composite Materials

Silicone is a kind of polymer material with high cross-linked structure,which is com-posed by Si-O-Si main chain.Due to the special molecular chain structure,silicone mate-rials are characterized by oxidation resistance,aging resistance,high and low temperature resistance and chemical corrosion resistance.Moreover,silicone materials have process-able properties,simple forming process,good mechanical property,non-toxic and pollution-free.Therefore,silicone has been widely concerned by researchers at home and abroad.In this paper,the main research progress and application directions of carbon-silicone composite at home and abroad in recent years are reviewed.

Research on Silicon Carbide Dispersion-Reinforced Hypereutectic Aluminum-Silicon Electronic Packaging Materials

The objective of this study is to improve the mechanical properties and machining performance of high thermal conductivity and low expansion silicon carbide dispersion-strengthened hypereutectic aluminum-silicon electronic packaging materials to meet the needs of aviation,aerospace,and electronic packaging fields.We used the powder metallurgy method and high-temperature hot pressing technology to prepare SiC/Al-Si composite materials with different SiC contents(5vol%,10vol%,15vol%,and 20vol%).The results showed that as the SiC content increased,the tensile strength of the composite material first increased and then decreased.The tensile strength was the highest when the SiC content was 15%;the sintering temperature significantly affected the composite material’s structural density and mechanical properties.Findings indicated 700℃was the optimal sintering and the optimal SiC content of SiC/Al-Si composite materials was between 10%and 15%.Besides,the sintering temperature should be strictly controlled to improve the material’s structural density and mechanical properties.

On the Strength of Silicon Carbide Particulate Reinforced Aluminium Alloy Matrix Composites

In the present study, the modified continuum model, quench strengthening and dislocation pile-up model was respectively used to estimate the yield strength of SiCp/AI composites. The experimental results showed that the modified shear lag model or quench strengthening model would underestimate the yield strength of SiCp/AI composites. However, the modified Hall-Petch correlation on the basis of the dislocation pile-up model, expressed as σcy = 244 + 371λ-1/2, fitted very well with the experimental data, which indicated that the strength increase of SiCp/AI composites might be due to the direct blocking of dislocation motion by the particulate-matrix interface. Namely, the dislocation pile-up is the most possible strengthening mechanism for SiCp/AI composites.

Diffusion Bonding of Silicon Carbide Particulate Reinforced 2024 Al Composites

A study has been made on diffusion bonding of SiCp/2024Ai composites by means of pure Al interlayer. In the condition of TB=843 K, PB=16 MPa, tB= 60 min, the diffusion bonded joint, with a shear strength of 235 MPa, was obtained when a 15 μm thick interlayer was used. The results of the shear testing and SEM indicate that fracture of the joint presented characteristics of ductile rupture.

Finite element simulation of the micromachining of nanosized-silicon-carbide-particle reinforced composite materials based on the cohesive zone model

A finite element method based on the cohesive zone model was used to study the micromachining process of nanosized silicon-carbide-particle(SiCp) reinforced aluminum matrix composites. As a hierarchical multiscale simulation method, the parameters for the cohesive zone model were obtained from the stress-displacement curves of the molecular dynamics simulation. The model considers the random properties of the siliconcarbide-particle distribution and the interface of bonding between the silicon carbide particles and the matrix.The machining mechanics was analyzed according to the chip morphology, stress distribution, cutting temperature, and cutting force. The simulation results revealed that the random distribution of nanosized SiCp causes non-uniform interaction between the tool and the reinforcement particles. This deformation mechanics leads to inhomogeneous stress distribution and irregular cutting force variation.

Machining studies of die cast aluminum alloy-silicon carbide composites

Metal matrix composites （MMCs） with high specific stiffness, high strength, improved wear resistance, and thermal properties are being increasingly used in advanced structural, aerospace, automotive, electronics, and wear applications. Aluminum alloy-silicon carbide composites were developed using a new combination of the vortex method and the pressure die-casting technique in the present work. Machining studies were conducted on the aluminum alloy-silicon carbide （SiC） composite work pieces using high speed steel （HSS） end-mill tools in a milling machine at different speeds and feeds. The quantitative studies on the machined work piece show that the surface finish is better for higher speeds and lower feeds. The surface roughness of the plain aluminum alloy is better than that of the aluminum alloy-silicon carbide composites. The studies on tool wear show that flank wear increases with speed and feed. The end-mill tool wear is higher on machining the aluminum alloy-silicon carbide composites than on machining the plain aluminum alloy.

Microstructure and properties of electronic packaging shell with high silicon carbide aluminum-base composites by semi-solid thixoforming

The electronic packaging shell with high silicon carbide aluminum-base composites was prepared by semi-solid thixoforming technique. The flow characteristic of the Si C particulate was analyzed. The microstructures of different parts of the shell were observed by scanning electron microscopy and optical microscopy, and the thermophysical and mechanical properties of the shell were tested. The results show that there exists the segregation phenomenon between the Si C particulate and the liquid phase during thixoforming, the liquid phase flows from the shell, and the Si C particles accumulate at the bottom of the shell. The volume fraction of Si C decreases gradually from the bottom to the walls. Accordingly, the thermal conductivities of bottom center and walls are 178 and 164 W·m-1·K-1, the coefficients of thermal expansion(CTE) are 8.2×10-6 and 12.6×10-6 K-1, respectively. The flexural strength decreases slightly from 437 to 347 MPa. The microstructures and properties of the shell show gradient distribution.

Research progress on silicon/carbon composite anode materials for lithium-ion battery

Silicon （Si） has been considered as one of the most promising anode material for tHe next generation lithium-ion batteries （LIBs） with high energy densities, due to its high theoretical capacity, abundant availability and environmental friendliness. However. silicon materials with low intrinsic electric and ionic conductivity suffer from huge volume variation during lithiation/delithiation processes leading to the pulverization of Si and subsequently resulting in severe capacity fading of the electrodes. Coupling of Si with carbon （C） realizes a favorable combination of the two materials properties, such as high lithiation capacity of Si and excellent mechanical and conductive properties of C. making silicon/carbon composite （Si/C） ideal candidates for LIBs anodes. In this review, recent progresses of Si/C materials utilized in LIBs are summarized in terms of structural design principles, material synthesis methods, morphological characteristics and electrochemical performances by highlighting the material structures. The mechanisms behind the performance enhancement are also discussed. Moreover, other factors that affect the performance of Si/C anodes, such as prelithiation, electrolyte additives, and binders, are also discussed. We aim to present a full scope of the Si/C-based anodes, and help understand and design future structures of Si/C anodes in LIBs,

Structural feature and electronic property of an (8, 0) carbon-silicon carbide nanotube heterojunction

A supercell of a nanotube heterojunction formed by an （8, 0） carbon nanotube （CNT） and an （8, 0） silicon carbide nanotube （SiCNT） is established, in which 96 C atoms and 32 Si atoms are included. The geometry optimization and the electronic property of the heterojunction are implemented through the first-principles calculation based on the density functional theory （DFT）. The results indicate that the structural rearrangement takes place mainly on the interface and the energy gap of the heterojunction is 0.31 eV, which is narrower than those of the isolated CNT and the isolated SiCNT. By using the average bond energy method, the valence band offset and the conduction band offset are obtained as 0.71 and -0.03 eV, respectively.

Semisolid forging electronic packaging shell with silicon carbon-reinforced copper composites

To fabricate electronic packaging shell of coppermatrix composite with characteristics of high ther mal conductivity and low thermal expansion coefficient, semisolid forming technology, and powder metallurgy was combined. Conventional mechanical mixing of Cu and SiC could have insufficient wettability, and a new method of semisolid processing was introduced for billets preparation. The SiC/Cu composites were first prepared by PM, and then, semisolid reheating was performed for the successive semisolid forging. Composite billets with SiC 35 % vol ume fraction were compacted and sintered pressurelessly, microstructure analysis showed that the composites pre pared by PM had high density, and the combination between SiC particles and Cualloy was good. Semisolid reheating was the crucial factor in determining the micro structure and thixotropic property of the billet. An opti mised reheating strategy was proposed： temperature 1,025 ℃and holding time 5 min.

Electrochemical behavior of insulin on pretreated carbon black electrode enhanced with silicon carbide nanostructure

We previously reported the direct electrochemical detection of insulin at bare carbon electrodes. Here a novel modified acetylene carbon black paste electrode(SiC/CB-CPE), based on the outstanding characteristics of silicon carbide nanostructure,was developed for the electrooxidation of insulin in alkaline solution and it was characterized by cyclic voltammetry(CV) and electrochemical impedance spectroscopy(EIS) in 5 mmol/L Fe(CN)63-/4- solution. It is found that silicon carbide nanostructure doped into the CB-CPE greatly facilitates the redox electrochemistry of Fe(CN)63-/4- probe and the electrochemical oxidation of insulin. The electrooxidation of insulin is a one-electron and one-proton reaction and an irreversible adsorption-controlled electrode process. The anodic oxidation current increases linearly with the concentration of insulin from 1×10-7mol/L to1.2×10-6mol/L in 0.1 mol/L Na2CO3-NaHCO3 buffer solution(pH 10.0) and the detection limit was 50 nmol/L. In addition, the SiC/CB-CPE shows good sensitivity, reproducibility, renewability and capacity of resisting disturbance.

Effect of Strain on the Electrical Resistance of Carbon Nanotube/Silicone Rubber Composites

Carbon nanotube （CNT） filled silicone rubber （SR） composites were synthesized by in situ polymerization.The effect of strain on the electrical resistance of the CNT/SR composites and the structure evolution of CNT networks during tensile deformation were investigated.The results showed that the CNT/SR composites had high sensitivity of resistance-strain response.In a wide strain range （0-125%）,the change of resistivity could reach 107,which was closely associated with the evolution process of the conductive CNT-network structure.The volume expansion of the composites in the tensile process led to a gradual decrease in the volume fraction of CNTs with the strain increase.When CNT loading was lower than the percolation threshold,CNT network was in disconnected state with a rapid increase in electrical resistance of the composites.Furthermore,the CNT loading had remarkable effect on the sensitivity of resistance-strain response in the composites.

Density functional theory calculation of the properties of carbon vacancy defects in silicon carbide

As a promisingmaterial for quantumtechnology,silicon carbide(SiC)has attracted great interest inmaterials science.Carbon vacancy is a dominant defect in 4H-SiC.Thus,understanding the properties of this defect is critical to its application,and the atomic and electronic structures of the defects needs to be identified.In this study,density functional theorywas used to characterize the carbon vacancy defects in hexagonal(h)and cubic(k)lattice sites.The zero-phonon line energies,hyperfine tensors,and formation energies of carbon vacancies with different charge states(2−,−,0,+and 2+)in different supercells(72,128,400 and 576 atoms)were calculated using standard Perdew-Burke-Ernzerhof and Heyd-Scuseria-Ernzerhof methods.Results show that the zero-phonon line energies of carbon vacancy defects are much lower than those of divacancy defects,indicating that the former is more likely to reach the excited state than the latter.The hyperfine tensors of VC+(h)and VC+(k)were calculated.Comparison of the calculated hyperfine tensor with the experimental results indicates the existence of carbon vacancies in SiC lattice.The calculation of formation energy shows that the most stable carbon vacancy defects in the material are VC 2+(k),VC+(k),VC(k),VC−(k)and VC 2−(k)as the electronic chemical potential increases.

Fabrication of Silicon/Carbon Composite Material with Silicon Waste and Carbon Nanofiber Applied in Lithium-Ion Battery

Silicon (Si) is regarded as a promising material for lithium-ion battery anode because of high theoretical capacity. Nevertheless, Si faces particle pulverization and rapid capacity fading due to serious volume change during the lithiation and the delithiation process. In this work, a silicon/carbon composite constituted to Si powder and carbon nanofiber (CNF) is produced to solve the above issues as a new design structure of anode material. The Si powder was recycled from the silicon slicing waste in photovoltaic industry and the CNF was from dry rice straws. By mixing the purified Si powder with CNF, the composite was synthesized by the freeze-drying method and calcination. In the cyclic test, Si adding with 1 wt% CNF showed 3091 mAh/g capacity in the first cycle and 1079 mAh/g capacity after 100 cycles at the current density of 0.5 A/g, which were both better than pristine Si. SEM images also show the composite structure can eliminate cracks on the surface of the electrode during cycling. CNF attaching on Si particles can increase specific surface area, so binder can easily combine the active materials and the conductive materials together. This strategy enhances the structure stability and prevents the electrode from delamination.

N-doped porous carbon nanofibers sheathed pumpkin-like Si/C composites as free-standing anodes for lithium-ion batteries

Dramatic capacity fading and poor rate performance are two main obstacles that severely hamper the widespread application of the Si anode owing to its large volume variation during cycling and low intrinsic electrical conductivity.To mitigate these issues,free-standing N-doped porous carbon nanofibers sheathed pumpkin-like Si/C composites(Si/C-ZIF-8/CNFs)are designed and synthesized by electrospinning and carbonization methods,which present greatly enhanced electrochemical properties for lithium-ion battery anodes.This particular structure alleviates the volume variation,promotes the formation of stable solid electrolyte interphase(SEI)film,and improves the electrical conductivity.As a result,the as-obtained free-standing Si/C-ZIF-8/CNFs electrode delivers a high reversible capacity of 945.5 mAh g^(-1) at 0.2 A g^(-1) with a capacity retention of 64% for 150 cycles,and exhibits a reversible capacity of 538.6 mA h g^(-1) at 0.5 A g^(-1) over 500 cycles.Moreover,the full cell composed of a freestanding Si/C-ZIF-8/CNFs anode and commercial LiNi_(1/3)Co_(1/3)Mn_(1/3)O_(2)(NCM)cathode shows a capacity of 63.4 mA h g^(-1) after 100 cycles at 0.2 C,which corresponds to a capacity retention of 60%.This rational design could provide a new path for the development of high-performance Si-based anodes.

Solvent-Free Synthesis of Ultrafine Tungsten Carbide Nanoparticles-Decorated Carbon Nanosheets for Microwave Absorption

Carbides/carbon composites are emerging as a new kind of binary dielectric systems with good microwave absorption performance.Herein,we obtain a series of tungsten carbide/carbon composites through a simple solvent-free strategy,where the solid mixture of dicyandiamide(DCA)and ammonium metatungstate(AM)is employed as the precursor.Ultrafine cubic WC1-x nanoparticles(3-4 nm)are in situ generated and uniformly dispersed on carbon nanosheets.This configuration overcomes some disadvantages of conventional carbides/carbon composites and is greatly helpful for electromagnetic dissipation.It is found that the weight ratio of DCA to AM can regulate chemical composition of these composites,while less impact on the average size of WC1-x nanoparticles.With the increase in carbon nanosheets,the relative complex permittivity and dielectric loss ability are constantly enhanced through conductive loss and polarization relaxation.The different dielectric properties endow these composites with distinguishable attenuation ability and impedance matching.When DCA/AM weight ratio is 6.0,the optimized composite can produce good microwave absorption performance,whose strongest reflection loss intensity reaches up to-55.6 dB at 17.5 GHz and qualified absorption bandwidth covers 3.6-18.0 GHz by manipulating the thickness from 1.0 to 5.0 mm.Such a performance is superior to many conventional carbides/carbon composites.

Formation of Polytypoids(12H and 21R)in High Temperature Nitrogen Atmosphere and Their Effects on SiC-MgAl_(2)O_(4) Composites

SiC-MgAl_(2)O_(4) composites with SiAlON polytypoids(12H and 21R)as the bonding phases were prepared using SiC fine powder,MgAl_(2)O_(4)fine powder and Al powder as raw materials.The effects of the firing temperature and the mass ratio of SiC to MgAl_(2)O_(4) on the formation of SiAlON polytypoids as well as on the properties of samples were studied.The formation mechanism of SiAlON polytypoids was discussed.The results show that firing at 1650℃in the nitrogen atmosphere,SiC-MgAl_(2)O_(4) composites with SiAlON polytypoids can be obtained.With the gradual increase of the mass ratio of SiC to MgAl_(2)O_(4) in the raw materials,12H forms first,and then coexists with 21H,finally,all 12H converts into 21R in samples.Both phases are plate crystals with flat and smooth edges.Compared with 21R,12H is conducive to improving the density and the cold mechanical properties of materials.After firing at 1650℃in the nitrogen atmosphere,with the mass ratio of SiC to MgAl_(2)O_(4) of 6:4,the sample has the cold modulus of rupture of 27 MPa,showing the optimal performance.

High Carbon Alloy Steels with Multiple Types of Ultra-fine Carbides and Their Characteristics

Under normal forging and annealing conditions, there are different ultra fine carbides (M3C, M23C6, M7Cj, M6C and MC) in high carbon alloy steels when alloy composition design is carried out properly. On the basis of carbides transformation orderliness, the alloy composition design of the high carbon alloy steels is conducted by phase-equilibrium thermodynamic calculation for Fe-Cr-W-Mo-V-C system. The nucleation and growth of new carbides, dissolution of previous partial carbides in these steels during annealing process, all these lead to ultra-fine distribution of carbides. Due to different crystal structures of carbides and different thermodynamics as well dynamics parameters of the carbides dissolution and precipitation, the range of quenching temperature of these steels is widened, and the good temper-resistance is obtained. The characteristics of heat treatment process and microstructure variance, and the carbides transformation for different temperature are explained by the phase-equilibrium component satisfactorily. Their bend and yield strength, flexibility and toughness all are advanced markedly comparing with that of kindred steels. Results of the applications have proved that the microstructure of ultra-fine carbides in these steels played importance roles in the enhancement of edginess and fatigue crack resistance of the die and knives.

Preparation of Microcapsules Containing Phase Change Material and Silicon Carbide Powder with Interfacial Polycondensation Reaction Method

The fundamental experiments were performed to establish the operational conditions required to prepare the microcapsules containing paraffin wax as a phase change material (PCM) and SiC powder with the interfacial polycondensation reaction. It was investigated how SiC powder affected a few characteristics of microcapsules such as the diameters of microcapsules, latent heat storage density, thermal responsibility and supercooling. In the experiment, the concentration of oil soluble surfactant, the revolution speed of impeller for preparing the (O/W) emulsion and the added weight of SiC powder were changed stepwise. The microcapsules containing PCM in which SiC powder was dispersed could be prepared well and characterized. The diameters of microcapsules increased by containing SiC powder and the content of SiC powder could be increased by performing surface modification of SiC powder. Latent heat storage density decreased with the content of SiC powder. Supercooling of PCM and thermal responsibility could be improved to some degree by containing SiC powder.