Chemical Forms of Heavy Metals in Carbonate-Derived Laterite and Enrichment of Its Iron Oxide Minerals

In this paper the seven-step continuous extracting method was employed in the studyof chemical forms of the six heavy metals Co, Zn, Pb, Cu, Cr and Mn. The result shows thatthe metals in the laterite are present in the chemical form of crystalline iron oxides andresidues, and they are transformed toward organic and exchangeable forms in the surface soil.Linear regression analysis indicates that the above heavy metals have a positive correlation withthe crystalline iron oxide minerals. The crystalline iron oxide minerals have a very importantrole to play in the enrichment of heavy metals, especially the solid components in the laterite.

Comparative Study between Dielectric Properties and Compaction Parameters: Case Study on Three Laterite Quarries

This work studies the variability of the relationship between relative permittivity and compaction parameters as a function of certain geotechnical properties for different laterite types. This study allows to purpose the dielectric permittivity as a third compaction parameter allowing to obtain a non destructive control méthod. Preliminary studies on Diack laterite had shown a good correlation. Additional investigations are carried out to verify the possibility of generalizing this correlation to three new laterite careers: Ngoudiane, Yéba and Fandene. To proceed, particle size analysis, Atterberg limits, specific weight tests and compaction according to the modified Proctor test were performed on laterite samples. Using the radar method, experimental permittivities are determined for laterite samples by the point method of propagation times and confirmed by the diffraction hyperbole method. The geotechnical and radar data obtained allowed correlations between permittivity and water content on the one hand and between permittivity and dry density on the other. The results show that the maximum dry density as a function of permittivity corresponds with the optimum Proctor, which confirms the results previously obtained on Diack laterite.

Performance evaluation of laterite soil embankment stabilized with bottom ash,coir fiber,and lime

In tropical regions,heavy rainfall induces erosion and shallow landslides on road embankments.Cement-based stabilization methods,common in these regions,contribute to climate change due to their high carbon footprint.This study explored the potential application of coir fiber-reinforced laterite soil-bottom ash mixtures as embankment materials in the tropics.The objective is to enhance engineered embankment slopes'erosion resistance and stability while offering reuse options for industrial byproducts.This study examined various mix designs for unconfined compressive strength(UCS)and permeability,utilizing 30%bottom ash(BA)and 1%coir fiber(CF)with varying sizes ranging from 10 to 40 mm,6%lime,and laterite soil(LS),followed by microstructural analyses.The results demonstrate that the compressive strength increases as the CF length increases to 25 mm.In contrast,permeability increases continuously with increasing CF length.Lime-treated mixtures exhibit superior short-and long-term strength and reduce permeability owing to the formation of cementitious materials,as confirmed by microstructural analyses.A lab-scale slope box was constructed to evaluate the surface erosion of the stabilized laterite soil embankment.Based on the rainfall simulation results,the LS-BA-CF mixtures show better resistance to erosion and deformation compared to untreated LS,especially when lime is added to the top layer.This study provides insights into a sustainable and cost-effective approach for slope stabilization using BA and CF,offering a promising solution for tropical regions susceptible to surface erosion and landslides.

Relative Dielectric Permittivity Variations during Compaction as a Mean of Compaction Quality Control: Case Study on Laterite Samples from Senegal

This study explores an alternative to the classical use of direct methods, as water content and dry density measurements, for compaction quality control. For this purpose, the dielectric properties of lateritic materials are determined by radar method and are compared with the permittivity determined from the Topp formula and from the CRIM model. This approach allowed to establish a relationship between the geotechnical properties determined during compaction such as dry density, water content or porosity with dielectric permittivity. The obtained results made it possible to determine an optimum dielectric permittivity corresponding to the optimum dry density and the optimum water content that could be used for non-destructive in situ compaction testing. Such an approach should improve the implementation and effectiveness of in situ compaction quality control of geotechnical infrastructures.

Influence of the Granular Class of Crushed Granites on the Litho-Stabilization of Samo Laterites (South-East of Côte d’Ivoire)

Most of the laterites found in Ivory Coast do not meet the technical conditions to be used in their natural state for the design of road foundations. Also, to meet the growing needs for road materials, various amendments are made to them, including litho-stabilization. Thus, this study proposes to understand the influence of the granular class of natural aggregates on the performance of laterites. To achieve this objective, different proportions of crushed granites of class 0/5, 0/15 and 5/15 have been incorporated into the soils of southern Côte d’Ivoire, especially in Samo. This modified soil has been subjected to mechanical tests such as the modified Proctor and CBR test. The results obtained show that the dry densities of the incorporated laterites containing crushed granites increase with the content of natural aggregates and decrease with the increase in the water content. Likewise, the CBR bearing indices at 95% of the Modified Optimum Proctor of the different compositions (laterites + crushed granites) increase with the proportion of aggregates. The addition of coarse aggregates to the laterites therefore promotes the establishment of a framework which improves its bearing capacity. From 20% to 30% crushed granites respectively of class 0/15;0/5 and 5/15, the values of the CBR obtained are greater than those of 30% therefore these modified soils can be used as a foundation layer for traffic of T1, T2 and T3 type. Likewise, the laterites’ mixtures with at least 40% crushed granites of class 0/15 and 0/5 can also be used for the foundation and base layers.

Effect of Polyethylene Terephthalate Plastic Waste on the Physico-Mechanical and Thermal Characteristics of Stabilized Laterite Bricks

The present work investigated the effect of polyethylene terephthalate (PET) plastic waste on the physico-mechanical and thermal properties of cement-stabilized laterite bricks to see the durability of the modified bricks (CSLB). Samples were formulated by mixing laterite, cement, and different percentages of PET (0%, 3%, 5%, and 7%) by volume. The bricks were produced using the M7MI Hydraform standard interlocking block and kept in the shade for a curing period of 28 days. The addition of 3% to 5% PET to the laterite stabilized with 10% cement results in a decrease in both dry and wet compressive strength, which is determined using the Controlab compression machine. However, the obtained results are in concordance with the standards. The thermal conductivity of CSLB, determined using the box method with the EI700 measurement cell, decreases as the PET content of the mixture increases. A decrease in bulk density from 1.67 to 1.58 g/cm3 was observed.

Physical Characterization of Laterite for the Formulation of Structural Concrete

This study presents another approach to the use of laterite as a common construction material for the development of a new type of concrete. Laterites are found all over the world and are used in various ways in road construction as sub-base, base course or wear courses. Being a material consisting in the raw state of sand and gravel, the study addresses its use for the formulation of structural concrete. The physical characterization made it possible to identify three granular classes distributed as follows: 28.26% passing at 80 μm, 32.12% sand (0.08/4 mm) and 39.62% nodule (4/25) mm. The absolute density of the aggregates varies from 2.73 and 2.82 from the sand to the nodules. The absorption rate varies from 3.01% and 5.71% respectively for sand and nodules. The granular compactness of the different granular classes studied varies from 0.580 to 0.630. The formulation of the concrete was made by the method of absolute volumes by varying the W/C ratio from 0.4 to 0.7, N/S from 2.2 to 2.8 and that of the cement dosage from 350 to 450 kg/m3. The results obtained show that the density of the concrete formulated based on these aggregates of lateritic origin have a density which varies between 2000 and 2300 kg/m3. With a cement content of 400 kg/m3, a W/C ratio of 0.4 and N/S of 2.8, concrete based on lateritic aggregates offers better mechanical performance in compression of approximately 21.23 ± 1.24 MPa at 28 days. This strength class obtained allows laterite concrete to be used as structural concrete in the structure of civil engineering works.

Characterization and Geotechnical Classification of Soils and Lateritic Gravelly Materials along the Songololo-Lufu Road Axis (Kongo Central Province, DR Congo)

This study aims to characterize from a geotechnical point of view, the soils as well as the lateritic gravels along the Songololo-Lufu road route in the Kongo Central Province in the Democratic Republic of Congo (DRC). Ten soil samples and eight lateritic gravel samples were analysed and tested in the laboratory. For each sample, identification parameters were determined such as particle size analysis, natural water content, Atterberg limits (plasticity index and consistency index), but also compaction and lift parameters such as optimal water content, maximum dry density and CBR lift index. All materials and soils have been classified according to the Congolese Road Standard (NRC) and according to the American HRB classification. The test results show us that clay soils almost always contain between 70% and 90% fine fraction;the grained fraction represents less than 30% in clay samples. For lateritic gravels soils, the percentage of fine elements varies between 35% and 15%;in sand around 20%;the gravelly fraction represents a little more than 50% of the soil. The majority of soil facies encountered define a plasticity index lower than 15. As for the consistency index, we obtained values greater than 1, both for clayey soils and for gravelly soils. The classification according to NRC defined for these soils the types Ae1 and Ae2 for the clayey facies and the types GL1 and GL2 for the gravelly soils, while that of the HRB identified the classes and subclasses A-6 and A-7-6 for clayey soils, and subclass A-2-6 for gravelly soils. The optimal water content values obtained range between 10.2% and 23.10%;the maximum dry densities are between 1.66 and 2.07 t/m3 and the CBR index is between 6 and 26. As for the lateritic gravels materials of the Songololo region, the percentage of fine elements generally remains between 12% and 31%;the plasticity index is between 8 and 18;the optimal dry density is around 2 t/m3;the optimal water content is between 9.8% and 14.5% and the CBR index is between 27 and 82. The Songololo-Lufu lateritic gravels are characteristic of laterites in the savannah region, with a high gravel fraction at the expense of the fine fraction, but low parameters such as the liquid limit and plasticity index.

Leaching behavior of metals from limonitic laterite ore by high pressure acid leaching

The leaching behavior of metals from a nickeliferous limonitic laterite ore was investigated by high pressure acid leaching process for the extraction of nickel and cobalt.The effects of sulfuric acid added,leaching temperature,leaching time and liquid/solid（L/S） ratio on metals extraction were examined.More than 97% Ni,96% Co,93% Mn,95% Mg and less than 1% Fe are extracted under optimum conditions.Analysis of the high pressure acid leaching residue by chemical and XRD analysis indicates that the residual iron and sulfur are mainly present in phases of hematite and alunite,respectively.The high pressure leaching process provides a simple and efficient way for the high recovery of nickel and cobalt from laterite ore,leaving residue as a suitable iron resource.

Mineralogy and crystal chemistry of a low grade nickel laterite ore

To acquire understanding of Ni enrichment from laterite ore,the mineralogy and crystal chemistry of a low grade limonite type nickel laterite ore sample assaying 0.97% Ni from Indonesia were studied using optical microscopy,X-ray diffraction（XRD）,scanning electron microscopy（SEM） and electron probe microanalysis（EPMA）.According to EPMA results,the mineral includes 80% goethite（（Fe,Ni,Al）O（OH）） with 0.87% Ni,15% silicate minerals with lizardite（（Mg,Fe,Ni）3Si2O5（OH）） and olivine（（Mg,Fe,Ni）2SiO4）,and 1.19% Ni,and other minor phases,such as hematite,maghemite,chromite and quartz,and no Ni was detected.The mineralogy of the laterite ore indicates that due to the complicated association of the various phases and the variable distribution of Ni,this refractory laterite ore can not be upgraded by traditional physical beneficiation processes.

Dechromization and dealumination kinetics in process of Na_2CO_3-roasting pretreatment of laterite ores

A novel process was proposed for the activation pretreatment of limonitic laterite ores by Na2CO3 roasting. Dechromization and dealumination kinetics of the laterite ores and the effect of particle size, Na2CO3-ore mass ratio, and roasting temperature on Cr and Al extraction were studied. Experimental results indicate that the extraction rates of Cr and Al are up to 99%and 82%, respectively, under the optimal particle size of 44–74μm, Na2CO3-to-ore mass ratio of 0.6：1, and temperature of 1000 ℃. Dechromization within the range of 600–800 oC is controlled by the diffusion through the product layer with an apparent activation energy of 3.9 kJ/mol, and that it is controlled by the chemical reaction at the surface within the range of 900–1100 ℃ with an apparent activation energy of 54.3 kJ/mol. Besides, the Avrami diffusion controlled model with on apparent activation energy of 16.4 kJ/mol is most applicable for dealumination. Furthermore, 96.8%Ni and 95.6%Co could be extracted from the alkali-roasting residues in the subsequent pressure acid leaching process.

Coal-based reduction mechanism of low-grade laterite ore

A low-grade nickel laterite ore was reduced at different reduction temperatures. The morphology of metallic particles was investigated by scanning electron microscopy （SEM） and energy dispersive spectroscopy （EDS）. Experimental results indicate that the metallic nickel and iron gradually assemble and grow into larger spherical particles with increasing temperature and prolonging time. After reduction, the nickel laterite ore obviously changes into two parts of Fe-Ni metallic particles and slag matrix. An obvious relationship is found between the reduction of iron magnesium olivine and its crystal chemical properties. The nickel and iron oxides are reduced to metallic by reductant, and the lattice of olivine is destroyed. The entire reduction process is comprised of oxide reduction and metallic phase growth.

Thermodynamic of selective reduction of laterite ore by reducing gases

As the sulfide ore deposits become less economical and environmental viable as a source of nickel,increasing attention is being paid to the laterite ores.But in the pyrometallurgical process of laterite,more efforts should be paid to control the reduction of iron oxide in order to get high nickel-content nickeliferous product.For these reasons,equilibrium condition of iron oxide when laterite ore was selectively reduced by CO2/CO,H2O/H2 and CO2/H2 was studied from the perspective of iron activity with an assumption that the activities of Fe O and Fe3O4 equal 1 in this work,and it well accounts for the inescapability of Fe metallization.Activity coefficient of iron in Ni-Fe binary solid alloy was calculated by Miedema model based on the known thermodynamics datum filed.According to Raoult＇s law,the relationship among the Fe/Ni ratio,reduction temperature and reduction gas composition was calculated when laterite ore was selectively reduced by the three different reduction systems.The calculation result was discussed and also compared with the experimental result.The trend of metal iron content in the reduction product of laterite ore varying with temperature and gas composition was well predicted by the calculation result.

Rare Earth Elements Geochemistry of Sheikh-Marut Laterite Deposit,NW Mahabad,West-Azarbaidjan Province,Iran

Laterite deposit at Sheikh-Marut （NW occurred within middle-upper Permian carbonate Mahabad, West-Azarbaidjan province, Iran） rocks. It consists of seven stratiform and/or discontinuous lenticular layers extending over 4.2 km in length and having thicknesses ranging from 3 to 14 m. Mineralogical data show that the ores contain kaolinite and hematite as major and boehmite, diaspore, halloysite, amesite, anatase, and muscovite-illite as minor mineral phases. The computed Ce anomaly values in the ores range from 0.05 to 20.84. Conservative index （e.g., Eu/Eu＊） suggests that this deposit is a product of alteration and weathering of basaltic rocks. Rhythmic increment of EREE values of the ores with approaching to the carbonate bedrocks shows an in-situ occurrence of lateritization processes. Mass change calculations of elements indicate that two competing processes namely leaching and fixation were the major regulating factors in concentration variation of REEs （La-Lu） in this deposit. The obtained results show that pH increase of weathering solutions by carbonate bedrocks, existence of organic matters, and the degree of comlexation with organic ligands played remarkable role in distribution of REEs during lateritization. Further geochemical considerations revealed that secondary phosphates, Mn-oxides and -hydroxides, diaspore, and anatase were the potential hosts for REEs in this deposit.

Adsorption of mercury on laterite from Guizhou Province,China

The adsorption behaviors of Hg(Ⅱ) on laterite from Guizhou Province,China,were studied and the adsorption mechanism was discussed.The results showed that different mineral compositons in the laterite will cause differences in the adsorption capacity of laterite to Hg(Ⅱ).Illite and non-crystalloids are the main contributors to enhancing the adsorption capacity of laterite to Hg(Ⅱ).The pH of the solution is an important factor affecting the adsorption of Hg(Ⅱ) on laterite.The alkalescent environment (pH 7-9) ...

Microwave assisted atmospheric acid leaching of nickel from laterite ore

The recovery of nickel from laterite ore with sulphuric acid under the effect of microwave irradiation was studied.The experimental results indicated that the extraction rate of nickel was influenced by reaction time,sulphuric acid concentration,and temperature,especially by microwave power.The results obtained from the experiments of orthogonal arrays showed that the optimum conditions of sulphuric acid concentration,reaction time,microwave power,and temperature were 25 vol.%,1.5 h,600 W,and 90°C,respectively.Under the optimal conditions,the nickel recovery could reach approximately 90.8%,which was higher than that obtained by conventional water bath heating.Kinetic experiments showed that the leaching of nickel in a sulphuric acid medium was controlled by chemical reaction occurring on the surface of laterite ore.The apparent activation energy was 38.9 kJ/mol.Microwave heating technology is efficient,clean,and easy to control and facilitate continuous processing of materials.

Activation pretreatment of limonitic laterite ores by alkali-roasting using NaOH

Activation pretreatment of Cr-containing limonitic laterite ores by NaOH roasting to remove Cr, Al, and Si, as well as its effect on Ni and Co extraction in the subsequent pressure acid leaching process was investigated. Characterization results of X-ray diffraction （XRD） and scanning electron microscopy/X-ray energy dispersive spectroscopy （SEM/XEDS） show that goethite is the major Ni-bearing mineral, and chromite is the minor one. Experimental results show that the leaching rates of Cr, Al, and Si are 95.6wt%, 83.8wt%, and 40.1wt%, respectively, under the optimal alkali-roasting conditions. Compared with the direct pressure acid leaching of laterite ores, the leaching rates of Ni and Co increase from 80.1wt% to 96.9wt% and 70.2wt% to 95.1wt% after pretreatment, respectively. Meanwhile, the grade of acid leaching iron residues increases from 54.4wt% to 62.5wt%, and these residues with low Cr content are more suitable raw materials for iron making.

Preparation of ferronickel from nickel laterite via coal-based reduction followed by magnetic separation

The sticking phenomenon between molten slag and refractory is one of the crucial problems when preparing ferronickel from laterite ore using rotary hearth fulnace or rotary kiln processes. This study aims to ameliorate sticking problems by using silicon dioxide （SiO2） to adjust the melting degree of file briquette during reduction roasting. Thermodynamic analysis indicates that the melting temperature of the slag gradually increases with an increase in the SiO2 proportion （SiO2/（SiO2 ＋ A1203 ＋ MgO） mass ratio）. Experimental validations also prove that the briquette retains its original shape when the SiO2 proportion is greater than 75wt%, and sticking problems axe avoided during reduction. A ferronickel product with 8.33wt% Ni and 84.71wt% Fe was prepared via reductive roasting at 1500~C for 90 min with a SiO2 proportion of 75wt% and a C/O molar ratio of 1.0 followed by dry magnetic separation; the corresponding recoveries of Ni and Fe reached 75.70% and 77.97%, respectively. The micro stxucture and phase txmlsformation of reduced briquette reveals that the aggregation and growth of ferroinckel particles were not significantly affected after adding SiO2 to the reduction process.

Preparation of zeolite NaA for CO_2 capture from nickel laterite residue

Zeolite NaA was successfully prepared from nickel laterite residue for the first time via a fusion-hydrothermal procedure. The structure and morphology of the as-synthesized zeolite NaA were characterized with a range of experimental techniques, such as X-ray diffraction, scanning electronic microscopy, and infrared spectroscopy. It was revealed that the structures of the produced zeolites were dependent on the molar ratios of the reactants and hydrothermal reaction conditions, so the synthesis conditions were optimized to obtain pure zeolite NaA. Adsorption of nitrogen and carbon dioxide on the prepared zeolite NaA was also measured and analyzed. The results showed that zeolite NaA could be prepared with reasonable purity, it had physicochemical properties comparable with zeolite NaA made from other methods, and it had excellent gas adsorption properties, thus demonstrating that zeolite NaA could be prepared from nickel laterite residue.

Extraction and separation of nickel and cobalt from saprolite laterite ore by microwave-assisted hydrothermal leaching and chemical deposition

Extraction and separation of nickel and cobalt from saprolite laterite ore were studied by using a method of microwave-assisted hydrothermal leaching and chemical deposition. The effects of leaching temperature and time on the extraction efficiencies of Ni2＋ and Co2＋ were investigated in detail under microwave conditions. It is shown that the extraction efficiencies of Ni2＋ and Co2＋ from the ore pre-roasted at 300℃ for 5 h were 89.19% and 61.89% when the leaching temperature and time were about 70℃ and 60 min, respectively. For the separation process of Ni and Co, the separation of main chemical components was performed by adjusting the pH values of sulfuric leaching solutions using a NaOH solution based on the different pH values of precipitation for metal hydroxides. The final separation efficiencies of Ni and Co were 77.29% and 65.87%, respectively. Furthermore, the separation efficiencies of Fe of 95.36% and Mg of 92.2% were also achieved at the same time.