Research on Heredity of Coarse Ferrite Grains

The changes in austenite grain size of the specimens with coarse ferrite grains under different heat treatment process were investigated.The focus was on studying the effect of annealing on refining coarse ferrite grains,as well as the influence of the ferrite grain size on the main technical indicators of gas carburizing.The results show that coarse ferrite grains may not necessarily cause the coarse austenite grains,but may result in mixed austenite grains.After annealing treatment,the coarse ferrite grains can be significantly refined and homogenized.Moreover,the coarse ferrite grains have no significant effects on hardnessand intergranular oxidationof gas carburizing.

Effect of manganese on the catalytic performance of an iron-manganese bimetallic catalyst for light olefin synthesis

A systematic study was carried out to investigate the promotion effect of manganese on the performance of a coprecipitated iron-manganese bimetallic catalyst for the light olefins synthesis from syngas. The catalyst samples were characterized by N2 physisorption, transmis- sion electron microscopy （TEM）, X-ray photoelectron spectroscopy （XPS）, powder X-ray diffraction （XRD）, Mossbauer spectroscopy, H2- differential thermogravimetric analysis （H2-DTG）, CO temperature-programmed reduction （CO-TPR） and CO2 temperature-programmed des- orption （CO2-TPD）. The Fischer-Tropsch synthesis （FTS） performance of the catalyst was measured at 1.5 MPa, 250 ℃ and syngas with H2/CO ratio of 2.0. The characterization results indicated that the addition of manganese decreases the catalyst crystallite size, and improves the catalyst BET surface area and pore volume. The presence of manganese suppresses the catalyst reduction and carburization in H2, CO and syngas, respectively. The addition of manganese improves the catalytic activity of water-gas shift reaction and suppresses the oxidation of iron carbides in the FTS reaction. The incorporation of manganese improves the catalyst surface basicity and results in a significant improvement in the selectivities to light olefins and heavy hydrocarbons （C5＋）, and furthermore an inhibition of methane formation in FTS. The pure iron catalyst （Mn-00） has the highest initial FTS catalytic activity （65%） and the lowest selectivity （17.35 wt%） to light olefins （C2=-C4=）. The addition of an appropriate amount of manganese can improve the catalyst FTS activity.

Microstructure of Surface Layer Formed at Low Temperature and High Carbon Concentration Carburizing with Rare Earth Element

A suitable carburized microstructure with fine granular dispersed carbides in hypereutectoid zone,ultra fine martensite in matrix and recrystallized austenite to be refined to the grain size of 12～14 has been obtained by a new process,which is a high carbon concentration carburizing with rare earth element at low temperature(860～880℃)in a discontinuous gas carburization furnace.There was not much difference for the microstructure in eutectic zone between this and conventional process.Forming mechanism of granular carbides has been also studied in this paper.

Effect of Rare Earths on Diffusion Coefficient and Transfer Coefficient of Carbon during Carburizing

The diffusion coefficient of carbon in surface layer of steel-20 rare earth carburixed at 880 degreesC and 900 degreesC for 8 h was calculated by substituting the measured layer depths into the diffusion equation. The mathematical model of the transfer coefficient of carbon was deduced based on the kinetics of weight gain during gas carburizing. The calculated results show that the main reason why the gas carburizing process is accelerated is due to the obvious increase in the diffusion coefficient and transfer coefficient of carbon resulted from the addition of RE.

Numerical Simulation on Carburizing and Quenching of Gear Ring

The carburizing process of the gear ring was simulated by taking into account the practical carburizing and quenching techniques of the gear ring and by solving the diffusion equation. The carbon content distribution in the carburized layer was obtained. Based on the results, the quenching process of the gear ring was then simulated using the metallic thermodynamics and FEM： it was found that the carburization remarkably affects the quenching process. Microstructures and stress distributions of the gear ring in the quenching process were simulated, and the results are confirmed by experiments.

Effect of Carburization on the Mechanical Properties of Biomedical Grade Titanium Alloys

Titanium cermets were successfully synthesized on the surface of biomedical grade titanium alloys by using sequential carburization method. The mechanical properties such as hardness, fracture toughness and plasticity were measured to estimate the potential application of titanium cermets. The results show that after carburization the surface hardness of titanium cermets was 778 HV, with a significant improvement of 128% compared with that of titanium alloys. In addition, the fracture toughness of titanium cermets was 21.5 × 10^6 Pa.m^1/2, much higher than that of other ceramics. Furthermore, the analysis of the loading-unloading curve in the nanoindentation test also indicates that the plasticity of titanium cermet reached 32.1%, a relatively high value which illustrates the combination of the metal and ceramics properties. The results suggest that sequential carburization should be an efficient way to produce titanium cermets with hard surface, high toughness and plasticity.

Wettability Modification for Biosurface of Titanium Alloy by Means of Sequential Carburization

Microporous titanium carbide coating was successfully synthesized on medical grade titanium alloy by using sequential carburization.Changes in the surface morphology of titanium alloy occasioned by sequential carburization were characterized and the wettability characteristics were quantified.Furthermore,the dispersion forces were calculated and discussed.The results indicate that sequential carburization is an effective way to modify the wettability of titanium alloy.After the carburization the surface dispersion force of titanium alloy increased from 76.5×10^(-3)J·m^(-2) to 105.5×10^(-3) J·m^(-2),with an enhancement of 37.9 %.Meanwhile the contact angle of titanium alloy decreased from 83° to 71.5°,indicating a significant improvement of wettability,which is much closer to the optimal water contact angle for cell adhesion of 70°.

Effect of process parameters on induction plasma reactive deposition of tungsten carbide from tungsten metal powder

Tungsten carbide deposit was made directly from tungsten metal powder through the reaction with methane in radio frequency induction plasma. Effect of major process parameters on the induction plasma reactive deposition of tungsten carbide was studied by optical microscopy, scanning electron microscopy, X ray diffraction analysis, water displacement method, and microhardness test. The results show that methane flow rate, powder feed rate, particle size, reaction chamber pressure and deposition distance have significant influences on the phase composition, density, and microhardness of the deposit. Extra carbon is necessary to ensure the complete conversion of tungsten metal into the carbide.

Observation and Analysis of the Microstructure in CarburizedSurface Layer of Steel 20Cr2Ni4A Treated with ConventionalAnd Rare Earth Carburizing Processes

Observation and analysis with TEM show that the fine granular dispersed carbides in hypereutectoid zone of steel 20Cr2Ni4A are distributed in the matrix of large number of lath martensite after rare earth carburizing. But while treating by conventional carburization and double quench hardening the retained carbides are finer and more dispersive, and its matrix is perfectly twin martersite. The different micrcotructures of matrix around carbide are formed with different kinds of carburization processes.

INDUCTION PLASMA REACTIVE DEPOSITION OF TUNGSTEN CARBIDE FROM TUNGSTEN METAL POWDER

Experimental results on the primary carburization reaction between the tungsten powder and methane in the induction plasma, and the secondary carburization of the deposit on substrate at high temperature are reported. Optical microscopy and scanning electron microscopy were used to examine the microstructures of starting tungsten powder, carburized powder, and deposit. X-ray diffraction analysis, thermal gravimetric analysis and microhardness measurement were used to characterize the structures and properties of the powder and the deposit. It is found that the primary carburization reaction in the induction plasma starts from the surface of tungsten particles when the particles are melted. Tungsten particles are partially carburized inside the reactive plasma. Complete carburization is achieved through the secondary carburization reaction of the deposit on substrate at high temperature.

Numerical Simulation of Reaction-Diffusion during Carburization of HK40 Steel

Two types of carbides M23C6 and M7C3 precipitate orderly as carbon concentration in a high Cr-Ni austenitic steel increases during carburization process. The mathematical model that describes diffusion of carbon and the precipitation of M23C6 and M7C3 has been studied. A criterion to judge when the transformation of M23C6 to M7C3 is over and M7C3 precipitates directly has been given in simulated calculation. By applying the model, the carburization of HK40 steel has been calculated by means of finite difference computation techniques. The pack carburization tests for the HK40 steel have been carried out at 1273 K. The comparison between the experimental and the calculated results show acceptable agreement.

Effect of Valence Electron Structure on Temper Process and Hardness of the Supersaturated Carburized Layer

By measuring the hardness of carburized layer of a new type supersaturated carburizing steel （35Cr3SiMnMoV） at different temper temperature for 2 h, the relationship curve between the carburized layer hardness and the temper temperature is established. The result indicates that the hardness goes down firstly, then up and down, just like a wave consistent with the temperature increase. A secondary hardening peak appears at 570 ℃ or so. Based on Empirical Election Theory （EET） of Solids and Molecules, the valence electron structures （VESs） containing α-Fe-C, α-Fe-C-Me segregation structure units and carbide are calculated. The laws of temper process and hardness change with the temper temperature are explained, and the fact that reconstruction of θ-Fe3C is prior to that of special carbide at high tempering is analyzed with the phase structure formation factor, S, being taken into consideration. Therefore, the laws of temper process and hardness change of supersaturated carburized layer at different temper temperature can be traced back to valence electron structure （VES） level of alloy phase.

Properties of oxide films grown on 25Cr20Ni alloy in air-H_2O and H_2-H_2O atmospheres

The oxidation kinetics,surface morphology and phase structure of oxide films grown on 25Cr20Ni alloy in air-H2O and H2-H2O atmospheres at 900 ℃ for 20 h were investigated.The anti-coking performance and resistance to carburization of the two oxide films were compared using 25Cr20Ni alloy tubes with an inner diameter of 10 mm and a length of 850 mm in a bench scale naphtha steam pyrolysis unit.The oxidation kinetics followed a parabolic law in an air-H2O atmosphere and a logarithm law in a H2-H2O atmosphere in the steady-state stage.The oxide film grown in the air-H2O atmosphere had cracks where the elements Fe and Ni were enriched and the un-cracked area was covered with octahedral-shaped MnCr2O4 spinels and Cr1.3Fe0.7O3 oxide clusters,while the oxide film grown in the H2-H2O atmosphere was intact and completely covered with dense standing blade MnCr2O4 spinels.In the pyrolysis tests,the anti-coking performance and resistance to carburization of the oxide film grown in the H2-H2O atmosphere were far better than that in the air-H2O atmosphere.The mass of coke formed in the oxide film grown in the H2-H2O atmosphere was less than 10％ of that in the air-H2O atmosphere.The Cr1.3Fe0.7O3 oxide clusters converted into Cr23C6 carbides and the cracks were filled with carbon in the oxide film grown in the air-H2O atmosphere after repeated coking and decoking tests,while the dense standing blade MnCr2O4 spinels remained unchanged in the oxide film grown in the H2-H2O atmosphere.The ethylene,propylene and butadiene yields in the pyrolysis tests were almost the same for the two oxide films.

Transformation Plasticity─The Effect on Metallo-Thermo-Mechanical Simulation of Carburized Quenching Process

Theory of metallo-thermo-mechamics and the developed CAE code offer a powerful tool to simulate residual stresses and distortion during heat treatment processes, in which the transformation plasticity is one of factors to be considered being coupled with stress/strain and metallic structure. It is pointed out in this paper that, especially in the case of carburized quenching, transformation plasticity plays very important role on the distortion, which is verified by axisymmetric finite element, employing heat treatment simulation code "HEARTS". Simulated results with the careful consideration on the effect of transformation plasticity reveal to improve remarkably the accuracy of prediction of the displacement and the mode of distortion, compensating the discrepancy between experimental and calculated results. Attention is also paid on the difference in transformation plasticity and conventional plasticity in simulating the volume fraction, stress and strain in ring-shaped specimen during quenching. Moreover some discussions are made on practical use of the effect, and recent experimental results on the coefficient of transformation plasticity are presented.

Effect of surface Cr/C infiltration on microstructure,mechanical properties and wear resistance of high chromium cast iron

A new type of high chromium cast iron(HCCI)was prepared,and its microstructure,mechanical properties,and abrasion resistance were investigated systematically.Results showed that after surface carburizing and chromizing,the microstructure of HCCI mainly consists of martensite,boride(M_(2)B),and carbide(M_(7)C_(3)),accompanied with a large amount of secondary precipitations M_(23)C_(6).Moreover,the morphology and hardness of the carbide and boride in HCCI change little,while the volume fraction of carbide and boride increases from 16.23%to 23.16%.This effectively increases the surface hardness of HCCI from 64.53±0.50 HRC to 66.58±0.50 HRC,with the result that the surface of HCCI possesses a better abrasion resistance compared to the center position.Furthermore,the wear mechanism of HCCI changes from micro-plowing to micro-cutting with the increase of surface hardness.

Accelerating Effect of Rare Earth in Steel on Its Surface-Carburizing Process

The carburization of steel type 20 with and without RE addition was investigated. The results show that RE in steel can accelerate carburizing process at 850 and 910 ℃. The optimum RE content in steel is about 0 032%. The mechanism of enhancing effect of RE on carburizing process was discussed.

Reduction and carburization of iron oxides for Fischer–Tropsch synthesis

The activation of iron oxide Fischer–Tropsch Synthesis(FTS) catalysts was investigated during pretreatment: reduction in hydrogen followed by carburization in either CO or syngas mixture, or simultaneously reduction and carburization in syngas. A combination of different complementary in situ techniques was used to gain insight into the behavior of Fe-based FTS catalysts during activation. In situ XRD was used to identify the crystalline structures present during both reduction in hydrogen and carburization. An increase in reduction rate was established when increasing the temperature. A complete reduction was demonstrated in the ETEM and a grain size dependency was proven, i.e. bigger grains need higher temperature in order to reduce. XPS and XAS both indicate the formation of a small amount of carbonaceous species at the surface of the bulk metallic iron during carburization.

Stress Field Analysis of Carburized Specimen and Its Numerical Simulation

Residual stress field of carburized specimens was determined experimentally and simulated by using a finite element method (FEM). The experimental results show that the compressive residual stress is formed in carburized layer of the specimen. The peak value of compressive stress appears inside of carburized layer. The calculated results are tallied with the measured ones quite well, which proves the FEM model used for simulation is correct. According to this model, the stress field of carburized specimen during quenching process was also analyzed in this paper.

Application of Empirical Electron Theory of Solids and Molecules to Composition Design of Multi-Component Medium-Low-Alloy Steels

For austenitic octahedral segregation structure units, their pure mathematics statistic distribu!ive probability is calculated by the empirical electron theory （EET） of solids and molecules and K-B formula. The practical distributive probability can be obtained only if the statistic distribution of austenitic octahedral segregation structure units and the interaction of the alloying elements in steel are considered. Based on 8 groups of experimental data of original steels, three empirical formulas revealing relationships between material macromechanics factor （Sm） and tensile strength （ab）, or impact energy （AK）, or hardness （HRC） of multi-component medium-low-alloy steels were established, respectively. Through the three empirical formulas, new supersaturated carburizing steel has been successfully designed and developed. The other 2 groups of the original experimental steels are used as the standard steel for testing the percentage error of the new steel. The results show that the calculated values are well consistent with those of measured ones and the new supersaturated carburized steel can meet the requirements of the die assembly of cold-drawn seamless stainless steel tube of Taiyuan Iron ＆ Steel （Group） Company LTD.

Double Glow Plasma Hydrogen-free Carburizing on Commercial Purity Titanium

A carburized layer with special physical and chemical properties was formed on the surface of commercial purity titanium by a double glow plasma hydrogen-free carburizing technique,High-purity netlike solid graphite was used as a raw material and commercial purity titanium was used as the substrate material.Argon gas was used as the working gas.The carburized layer can be obviously observed under a microscope.X-ray diffraction indicates that TiC phase with higher hardness and dissociate state carbon phase was formed in the carburized layer.The glow discharge spectrum（GDS） analysis shows that the carbon concentration distributes grodiently along the depth of carburized layer.The surface hardness of the substrate increases obviously.The hardness distributes gradiently from the surface to inner of carburized layer.The friction coefficient reduces by more than 1/2,the ratio wear rate decreases by above three orders of magnitude.The wear resistance of the substrate material is improved-consumedly.