A carrier tracking loop which can adjust the loop parameters adaptively is proposed for high dynamic application. Three modules, called the α-β-γT filter model, adaptive loop structure mod- el and adaptive loop ban...A carrier tracking loop which can adjust the loop parameters adaptively is proposed for high dynamic application. Three modules, called the α-β-γT filter model, adaptive loop structure mod- el and adaptive loop bandwidth model respectively, are added in the presented tracking loop com- pared with the traditional carrier tracking loop based on the second-order frequency lock loop （FLL） assisting third-order phase lock loop （PLL） loop filter. And the optimization methods for the track- ing bandwidth and the carrier loop order are analyzed. The real-time estimation methods of the dy- namic parameters, the velocity, acceleration and jerk along the line of sight （LOS） between the sat- ellite and the receiver＇ s antenna, and the measurement parameters are discussed based on the pres- ented α-β-γ filter algorithm. A method is introduced to improve the filter＇ s dynamic response to meet high dynamic application by self-adjusted α-β-γ filter coefficient used in the tracking loop. The performance of three cases with different carrier tracking loop is compared by simulation.展开更多
Chemical looping combustion （CLC） of carbonaceous compounds has been proposed, in the past decade, as an efficient method for CO2 capture without cost of extra energy penalties. The technique involves the use of a m...Chemical looping combustion （CLC） of carbonaceous compounds has been proposed, in the past decade, as an efficient method for CO2 capture without cost of extra energy penalties. The technique involves the use of a metal oxide as an oxygen carrier that transfers oxygen from combustion air to fuels. The combustion is carried out in a two-step process： in the fuel reactor, the fuel is oxidized by a metal oxide, and in the air reactor, the reduced metal is oxidized back to the original phase. The use of iron oxide as an oxygen carrier has been investigated in this article. Particles composed of 80 wt% Fe2O3, together with Al2O3 as binder, have been prepared by impregnation methods. X-ray diffraction （XRD） analysis reveals that Fe2O3 does not interact with the Al2O3 binder after multi-cycles. The reactivity of the oxygen carrier particles has been studied in twenty-cycle reduction-oxidation tests in a thermal gravimetrical analysis （TGA） reactor. The components in the outlet gas have been analyzed. It has been observed that about 85% of CH4 converted to CO2 and H2O during most of the reduction periods. The oxygen carrier has kept quite a high reactivity in the twenty-cycle reactions. In the first twenty reaction cycles, the reaction rates became slightly higher with the number of cyclic reactions increasing, which was confirmed by the scanning electron microscopy （SEM） test results. The SEM analysis revealed that the pore size inside the particle had been enlarged by the thermal stress during the reaction, which was favorable for diffusion of the gaseous reactants into the particles. The experimental results suggested that the Fe2O3/Al2O3 oxygen carrier was a promising candidate for a CLC system.展开更多
Thermodynamic parameters of chemical reactions in the system were carried out through thermodynamic analysis. According to the Gibbs free energy minimization principle of the system, equilibrium composition of the rea...Thermodynamic parameters of chemical reactions in the system were carried out through thermodynamic analysis. According to the Gibbs free energy minimization principle of the system, equilibrium composition of the reactions of chemical-looping gasification (CLG) of biomass with natural hematite (Fe2O3) as oxygen carrier were analyzed using commercial software of HSC Chemistry 5.1. The feasibility of the CLG of biomass with hematite was experimental verified in a lab-scale bubbling fluidized bed reactor using argon as fluidizing gas. It was indicated the experimental results were consistent with the theoretical analysis. The presence of oxygen carrier gave a significant effect on the biomass conversion and improved the synthesis gas yield obviously. It was observed that the gas content of CO and H2 was over 70% in CLG of biomass. The reduced hematite particles mainly existed in form of FeO. It was showed that the reduction of natural hematite with biomass proceeds in a stepwise manner from Fe2O3 →Fe3O4→ FeO. Reduction product of natural hematite can be restored the lattice oxygen by oxidation with air.展开更多
The chemical looping gasification uses an oxygen carrier for solid fuel gasification by supplying insufficient lattice oxygen. The effect of gasifying medium on the coal chemical looping gasification with Ca SO4 as ox...The chemical looping gasification uses an oxygen carrier for solid fuel gasification by supplying insufficient lattice oxygen. The effect of gasifying medium on the coal chemical looping gasification with Ca SO4 as oxygen carrier is investigated in this paper. The thermodynamical analysis indicates that the addition of steam and CO2 into the system can reduce the reaction temperature, at which the concentration of syngas reaches its maximum value.Experimental result in thermogravimetric analyzer and a fixed-bed reactor shows that the mixture sample goes through three stages, drying stage, pyrolysis stage and chemical looping gasification stage, with the temperature for three different gaseous media. The peak fitting and isoconversional methods are used to determine the reaction mechanism of the complex reactions in the chemical looping gasification process. It demonstrates that the gasifying medium(steam or CO2) boosts the chemical looping process by reducing the activation energy in the overall reaction and gasification reactions of coal char. However, the mechanism using steam as the gasifying medium differs from that using CO2. With steam as the gasifying medium, parallel reactions occur in the beginning stage, followed by a limiting stage shifting from a kinetic to a diffusion regime. It is opposite to the reaction mechanism with CO2 as the gasifying medium.展开更多
Copper（Ⅱ） oxide in varying ratios was combined with either an alumina-based cement（Al300）, or CaO derived from limestone as support material in a mechanical pelletiser. This production method was used to investig...Copper（Ⅱ） oxide in varying ratios was combined with either an alumina-based cement（Al300）, or CaO derived from limestone as support material in a mechanical pelletiser. This production method was used to investigate its influence on possible mechanical and chemical improvements for oxygen carriers in chemical looping processes. These materials were tested in a lab-scale fluidised bed with CO or CH;as a reducing gas at 950 °C. As expected, the oxygen carriers containing a greater ratio of support material exhibited an enhanced crushing strength. Oxygen carriers comprised of a 1:3 ratio of support material to active CuO exhibited increased crushing strength by a minimum of 280% compared to pure CuO pellets.All oxygen carriers exhibited a high CO conversion yield and were fully reducible from CuO to Cu. For the initial redox cycle, Al300-supported oxygen carriers showed the highest fuel and oxygen carrier conversion. The general trend observed was a decline in conversion with an increasing number of redox cycles.In the case of CaO-supported oxygen carriers, all but one of the oxygen carriers suffered agglomeration.The agglomeration was more severe in carriers with higher ratios of CuO. Oxygen carrier Cu25Al75（75 wt% aluminate cement and 25 wt% CuO）, which did not suffer from agglomeration, showed the highest attrition with a loss of approximately 8% of its initial mass over 25 redox cycles. The reducibility of the oxygen carriers was limited with CH;in comparison to CO. CH;conversion were 15%-25% and 50% for Cu25Ca75（25 wt% CuO and 75 wt% CaO） and Cu25Al75, respectively. Cu25Ca75 demonstrated improved conversion, whereas Cu25Al75 exhibited a trending decrease in conversion with increasing redox cycles.展开更多
The cycle life of oxygen carrier（OC） is crucial to the practical applications of chemical looping combustion（CLC）. Cycle performance of Cu/SiO2 prepared with a mechanical mixing method was evaluated based on a CLC...The cycle life of oxygen carrier（OC） is crucial to the practical applications of chemical looping combustion（CLC）. Cycle performance of Cu/SiO2 prepared with a mechanical mixing method was evaluated based on a CLC process characterized with an added methane steam reforming step. The Cu/SiO2 exhibited high redox reactivity in the initial cycles, while the performance degraded with cycle number. Through characterization of the degraded Cu/SiO2, the performance degradation was mainly caused by the secondary particles＇ fragmentation and the fine particles＇ local agglomeration, which worsened the distribution and diffusion of the reactive gases in the packed bed. A regeneration method of the degraded OC based on re-granulation has been proposed, and its mechanism has been illustrated. With this method, the performance of the degraded OC through 420 redox cycles was recovered to a level close to the initial one.展开更多
Chemical looping dry reforming（CLDR） is an innovative technology for CO2 utilization using the chemical looping principle.The CLDR process consists of three stages,i.e.CH4 reduction,CO2 reforming,and air oxidation.S...Chemical looping dry reforming（CLDR） is an innovative technology for CO2 utilization using the chemical looping principle.The CLDR process consists of three stages,i.e.CH4 reduction,CO2 reforming,and air oxidation.Spinel nickel ferrite（NiFe2O4） was prepared and its multi-cycle performance as an oxygen carrier for CLDR was experimentally investigated.X-ray diffraction（XRD） and Laser Raman spectroscopy showed that a pure spinel crystalline phase（NiFe2O4） was obtained by a parallel flow co-precipitating method.NiFe2O4was reduced into Fe-Ni alloy and wustite（FexO） during the CH4 reduction process.Subsequent oxidation of the reduced oxygen carrier was performed with CO2 as an oxidant to form an intermediate state：a mixture of spinel Ni（1-x）Fe（2＋x）O4,Fe（2＋y）O4 and metallic Ni.And CO was generated in parallel during this stage.Approximate 185 mL of CO was generated for 1 g spinel NiFe2O4 in a single cycle.The intermediate oxygen carrier was fully oxidized in the air oxidation stage to form a mixture of Ni（1＋x）Fe（2-x）O4 and Fe2O3.Although the original state of oxygen carrier（NiFe2O4） was not fully regenerated and agglomeration was observed,a good recyclability was shown in 10 successive redox cycles.展开更多
In deep space exploration,many engineering and scientific requirements require the accuracy of the measured Doppler frequency to be as high as possible.In our paper,we analyze the possible frequency measurement points...In deep space exploration,many engineering and scientific requirements require the accuracy of the measured Doppler frequency to be as high as possible.In our paper,we analyze the possible frequency measurement points of the third-order phase-locked loop(PLL)and find a new Doppler measurement strategy.Based on this finding,a Doppler frequency measurement algorithm with significantly higher measurement accuracy is obtained.In the actual data processing,compared with the existing engineering software,the accuracy of frequency of 1 second integration is about 5.5 times higher when using the new algorithm.The improved algorithm is simple and easy to implement.This improvement can be easily combined with other improvement methods of PLL,so that the performance of PLL can be further improved.展开更多
This paper presents an approach of singular value de- composition plus digital phase lock loop to solve the difficult problem of blind pseudo-noise （PN） sequence estimation in low signal to noise ratios （SNR） dire...This paper presents an approach of singular value de- composition plus digital phase lock loop to solve the difficult problem of blind pseudo-noise （PN） sequence estimation in low signal to noise ratios （SNR） direct sequence spread spectrum （DS-SS） signals with residual carrier. This approach needs some given parameters, such as the period and code rate of PN sequence. The received signal is firstly sampled and divided into non-overlapping signal vectors according to a temporal window, whose duration is two periods of PN sequence. An autocorrelation matrix is then computed and accumulated by those signal vectors one by one. The PN sequence with residual carrier can be estimated by the principal eigenvector of the autocorrelation matrix. Further more, a digital phase lock loop is used to process the estimated PN sequence, it estimates and tracks the residual carrier and removes the residual carrier in the end. Theory analysis and computer simulation results show that this approach can effectively realize the PN sequence blind estimation from the input DS-SS signals with residual carrier in lower SNR.展开更多
As an important part of the communication system, synchronization technology is a communication system to run the correct protection, has been a hot topic in communication systems research. Four-phase phase shift keyi...As an important part of the communication system, synchronization technology is a communication system to run the correct protection, has been a hot topic in communication systems research. Four-phase phase shift keying (QPSK) circuit structure is relatively simple, and has a good band utilization, in the modern communication has a wide range of applications. Corresponding research on carrier synchronization for QPSK coherent demodulation is carried out. By comparing several carrier recovery loops, The quaternary loose tail loop is selected as carrier recovery loop. First of all, the core part of the digital phase-locked loop analysis and implementation, and finally through the tool Simulink to complete the realization of the system.展开更多
In deep space exploration,it is necessary to improve the accuracy of frequency measurement to meet the requirements of precise orbit determination and various scientific studies.A phase detector is one of the key modu...In deep space exploration,it is necessary to improve the accuracy of frequency measurement to meet the requirements of precise orbit determination and various scientific studies.A phase detector is one of the key modules that restricts the tracking performance of phase-locked loop(PLL).Based on the phase relationship between adjacent signals in the time domain,a novel phase detector is presented to replace the arctangent phase detector.The new PLL,which is a closed loop signal correlation algorithm,shows good performance in tracking signals with high precision and the tracking accuracy of frequency of1 second integration is close to Cramer-Rao lower bound(CRLB)when setting proper parameters.Actual data processing results further illustrate the excellent performance of the novel PLL.展开更多
In this paper, a new strategy of switchable CMOS phase-locked loop frequency synthesizer is proposed to increase its tuning range. The switchable PLL which integrates two phase-locked loops with different tuning frequ...In this paper, a new strategy of switchable CMOS phase-locked loop frequency synthesizer is proposed to increase its tuning range. The switchable PLL which integrates two phase-locked loops with different tuning frequencies are designed and fabricated in 0.5 μm n-well CMOS process. Cadence/Spectre simulations show that the frequency range of the switchable phased-locked loop is between 320 MHz to 1.15 GHz. The experimental results show that the RMS jitter of the phase-locked loop changes from 26 ps to 123 ps as output frequency varies. For 700 MHz carrier frequency, the phase noise of the phase-locked loop reaches as low as ?81 dBc/Hz at 10 kHz offset frequency and ?104 dBc/Hz at 1 MHz offset frequency. A device degradation model due to hot carrier effects has been used to analyze the jitter and phase noise performance in an open loop voltage-controlled oscillator. The oscillation frequency of the voltage-controlled oscillator decreases by approximately 100 to 200 MHz versus the bias voltage and the RMS jitter increases by 40 ps under different phase-locked loop output frequencies after 4 hours of stress time.展开更多
基金Supported by the Ministerial Level Foundation(B222006060)
文摘A carrier tracking loop which can adjust the loop parameters adaptively is proposed for high dynamic application. Three modules, called the α-β-γT filter model, adaptive loop structure mod- el and adaptive loop bandwidth model respectively, are added in the presented tracking loop com- pared with the traditional carrier tracking loop based on the second-order frequency lock loop （FLL） assisting third-order phase lock loop （PLL） loop filter. And the optimization methods for the track- ing bandwidth and the carrier loop order are analyzed. The real-time estimation methods of the dy- namic parameters, the velocity, acceleration and jerk along the line of sight （LOS） between the sat- ellite and the receiver＇ s antenna, and the measurement parameters are discussed based on the pres- ented α-β-γ filter algorithm. A method is introduced to improve the filter＇ s dynamic response to meet high dynamic application by self-adjusted α-β-γ filter coefficient used in the tracking loop. The performance of three cases with different carrier tracking loop is compared by simulation.
基金Supported by the National Natural Science Foundation of China (No.50574046 and 50164002, )Natural Science Foun-dation of Yunnan Province (No. 2004E0012Q).
文摘Chemical looping combustion （CLC） of carbonaceous compounds has been proposed, in the past decade, as an efficient method for CO2 capture without cost of extra energy penalties. The technique involves the use of a metal oxide as an oxygen carrier that transfers oxygen from combustion air to fuels. The combustion is carried out in a two-step process： in the fuel reactor, the fuel is oxidized by a metal oxide, and in the air reactor, the reduced metal is oxidized back to the original phase. The use of iron oxide as an oxygen carrier has been investigated in this article. Particles composed of 80 wt% Fe2O3, together with Al2O3 as binder, have been prepared by impregnation methods. X-ray diffraction （XRD） analysis reveals that Fe2O3 does not interact with the Al2O3 binder after multi-cycles. The reactivity of the oxygen carrier particles has been studied in twenty-cycle reduction-oxidation tests in a thermal gravimetrical analysis （TGA） reactor. The components in the outlet gas have been analyzed. It has been observed that about 85% of CH4 converted to CO2 and H2O during most of the reduction periods. The oxygen carrier has kept quite a high reactivity in the twenty-cycle reactions. In the first twenty reaction cycles, the reaction rates became slightly higher with the number of cyclic reactions increasing, which was confirmed by the scanning electron microscopy （SEM） test results. The SEM analysis revealed that the pore size inside the particle had been enlarged by the thermal stress during the reaction, which was favorable for diffusion of the gaseous reactants into the particles. The experimental results suggested that the Fe2O3/Al2O3 oxygen carrier was a promising candidate for a CLC system.
文摘Thermodynamic parameters of chemical reactions in the system were carried out through thermodynamic analysis. According to the Gibbs free energy minimization principle of the system, equilibrium composition of the reactions of chemical-looping gasification (CLG) of biomass with natural hematite (Fe2O3) as oxygen carrier were analyzed using commercial software of HSC Chemistry 5.1. The feasibility of the CLG of biomass with hematite was experimental verified in a lab-scale bubbling fluidized bed reactor using argon as fluidizing gas. It was indicated the experimental results were consistent with the theoretical analysis. The presence of oxygen carrier gave a significant effect on the biomass conversion and improved the synthesis gas yield obviously. It was observed that the gas content of CO and H2 was over 70% in CLG of biomass. The reduced hematite particles mainly existed in form of FeO. It was showed that the reduction of natural hematite with biomass proceeds in a stepwise manner from Fe2O3 →Fe3O4→ FeO. Reduction product of natural hematite can be restored the lattice oxygen by oxidation with air.
基金Supported by the Research and Development Program of the Korea Institute of Energy Research(KIER)(B4-2431-04)the National Natural Science Foundation of China(21276129,20876079)the Natural Science Funds for Distinguished Young Scholar in Shandong Province(JQ200904)
文摘The chemical looping gasification uses an oxygen carrier for solid fuel gasification by supplying insufficient lattice oxygen. The effect of gasifying medium on the coal chemical looping gasification with Ca SO4 as oxygen carrier is investigated in this paper. The thermodynamical analysis indicates that the addition of steam and CO2 into the system can reduce the reaction temperature, at which the concentration of syngas reaches its maximum value.Experimental result in thermogravimetric analyzer and a fixed-bed reactor shows that the mixture sample goes through three stages, drying stage, pyrolysis stage and chemical looping gasification stage, with the temperature for three different gaseous media. The peak fitting and isoconversional methods are used to determine the reaction mechanism of the complex reactions in the chemical looping gasification process. It demonstrates that the gasifying medium(steam or CO2) boosts the chemical looping process by reducing the activation energy in the overall reaction and gasification reactions of coal char. However, the mechanism using steam as the gasifying medium differs from that using CO2. With steam as the gasifying medium, parallel reactions occur in the beginning stage, followed by a limiting stage shifting from a kinetic to a diffusion regime. It is opposite to the reaction mechanism with CO2 as the gasifying medium.
文摘Copper（Ⅱ） oxide in varying ratios was combined with either an alumina-based cement（Al300）, or CaO derived from limestone as support material in a mechanical pelletiser. This production method was used to investigate its influence on possible mechanical and chemical improvements for oxygen carriers in chemical looping processes. These materials were tested in a lab-scale fluidised bed with CO or CH;as a reducing gas at 950 °C. As expected, the oxygen carriers containing a greater ratio of support material exhibited an enhanced crushing strength. Oxygen carriers comprised of a 1:3 ratio of support material to active CuO exhibited increased crushing strength by a minimum of 280% compared to pure CuO pellets.All oxygen carriers exhibited a high CO conversion yield and were fully reducible from CuO to Cu. For the initial redox cycle, Al300-supported oxygen carriers showed the highest fuel and oxygen carrier conversion. The general trend observed was a decline in conversion with an increasing number of redox cycles.In the case of CaO-supported oxygen carriers, all but one of the oxygen carriers suffered agglomeration.The agglomeration was more severe in carriers with higher ratios of CuO. Oxygen carrier Cu25Al75（75 wt% aluminate cement and 25 wt% CuO）, which did not suffer from agglomeration, showed the highest attrition with a loss of approximately 8% of its initial mass over 25 redox cycles. The reducibility of the oxygen carriers was limited with CH;in comparison to CO. CH;conversion were 15%-25% and 50% for Cu25Ca75（25 wt% CuO and 75 wt% CaO） and Cu25Al75, respectively. Cu25Ca75 demonstrated improved conversion, whereas Cu25Al75 exhibited a trending decrease in conversion with increasing redox cycles.
基金supported by the Beijing Science and Technology Program(Grant no.Z131100005613045)the National Natural Science Foundation of China(Grant no.51306015)the Fundamental Research Funds for the Central Universities(Grant no.FRF-SD-12-013A)
文摘The cycle life of oxygen carrier（OC） is crucial to the practical applications of chemical looping combustion（CLC）. Cycle performance of Cu/SiO2 prepared with a mechanical mixing method was evaluated based on a CLC process characterized with an added methane steam reforming step. The Cu/SiO2 exhibited high redox reactivity in the initial cycles, while the performance degraded with cycle number. Through characterization of the degraded Cu/SiO2, the performance degradation was mainly caused by the secondary particles＇ fragmentation and the fine particles＇ local agglomeration, which worsened the distribution and diffusion of the reactive gases in the packed bed. A regeneration method of the degraded OC based on re-granulation has been proposed, and its mechanism has been illustrated. With this method, the performance of the degraded OC through 420 redox cycles was recovered to a level close to the initial one.
基金the financial support by the National Natural Science Foundation of China(51406214 and51406208)supported by the Natural science Foundation of Guangdong Province(2015A030313719)the Science&Technology Research Project of Guangdong Province(2013B050800008)
文摘Chemical looping dry reforming（CLDR） is an innovative technology for CO2 utilization using the chemical looping principle.The CLDR process consists of three stages,i.e.CH4 reduction,CO2 reforming,and air oxidation.Spinel nickel ferrite（NiFe2O4） was prepared and its multi-cycle performance as an oxygen carrier for CLDR was experimentally investigated.X-ray diffraction（XRD） and Laser Raman spectroscopy showed that a pure spinel crystalline phase（NiFe2O4） was obtained by a parallel flow co-precipitating method.NiFe2O4was reduced into Fe-Ni alloy and wustite（FexO） during the CH4 reduction process.Subsequent oxidation of the reduced oxygen carrier was performed with CO2 as an oxidant to form an intermediate state：a mixture of spinel Ni（1-x）Fe（2＋x）O4,Fe（2＋y）O4 and metallic Ni.And CO was generated in parallel during this stage.Approximate 185 mL of CO was generated for 1 g spinel NiFe2O4 in a single cycle.The intermediate oxygen carrier was fully oxidized in the air oxidation stage to form a mixture of Ni（1＋x）Fe（2-x）O4 and Fe2O3.Although the original state of oxygen carrier（NiFe2O4） was not fully regenerated and agglomeration was observed,a good recyclability was shown in 10 successive redox cycles.
基金supported by the National Natural Science Foundation of China(Grant Nos.11773060,11973074,U1831137 and 11703070)National Key Basic Research and Development Program(2018YFA0404702)+1 种基金Shanghai Key Laboratory of Space Navigation and Positioning(3912DZ227330001)the Key Laboratory for Radio Astronomy of CAS。
文摘In deep space exploration,many engineering and scientific requirements require the accuracy of the measured Doppler frequency to be as high as possible.In our paper,we analyze the possible frequency measurement points of the third-order phase-locked loop(PLL)and find a new Doppler measurement strategy.Based on this finding,a Doppler frequency measurement algorithm with significantly higher measurement accuracy is obtained.In the actual data processing,compared with the existing engineering software,the accuracy of frequency of 1 second integration is about 5.5 times higher when using the new algorithm.The improved algorithm is simple and easy to implement.This improvement can be easily combined with other improvement methods of PLL,so that the performance of PLL can be further improved.
基金supported by the National Natural Science Foundation of China (10776040 60602057)+4 种基金Program for New Century Excellent Talents in University (NCET)the Project of Key Laboratory of Signal and Information Processing of Chongqing (CSTC2009CA2003)the Natural Science Foundation of Chongqing Science and Technology Commission (CSTC2009BB2287)the Natural Science Foundation of Chongqing Municipal Education Commission (KJ060509 KJ080517)
文摘This paper presents an approach of singular value de- composition plus digital phase lock loop to solve the difficult problem of blind pseudo-noise （PN） sequence estimation in low signal to noise ratios （SNR） direct sequence spread spectrum （DS-SS） signals with residual carrier. This approach needs some given parameters, such as the period and code rate of PN sequence. The received signal is firstly sampled and divided into non-overlapping signal vectors according to a temporal window, whose duration is two periods of PN sequence. An autocorrelation matrix is then computed and accumulated by those signal vectors one by one. The PN sequence with residual carrier can be estimated by the principal eigenvector of the autocorrelation matrix. Further more, a digital phase lock loop is used to process the estimated PN sequence, it estimates and tracks the residual carrier and removes the residual carrier in the end. Theory analysis and computer simulation results show that this approach can effectively realize the PN sequence blind estimation from the input DS-SS signals with residual carrier in lower SNR.
文摘As an important part of the communication system, synchronization technology is a communication system to run the correct protection, has been a hot topic in communication systems research. Four-phase phase shift keying (QPSK) circuit structure is relatively simple, and has a good band utilization, in the modern communication has a wide range of applications. Corresponding research on carrier synchronization for QPSK coherent demodulation is carried out. By comparing several carrier recovery loops, The quaternary loose tail loop is selected as carrier recovery loop. First of all, the core part of the digital phase-locked loop analysis and implementation, and finally through the tool Simulink to complete the realization of the system.
基金supported by the National Natural Science Foundation of China(11773060,11973074,U1831137,11703070 and 11803069)the National Key Basic Research and Development Program(2018YFA0404702)+1 种基金Shanghai Key Laboratory of Space Navigation and Positioning(3912DZ227330001)the Key Laboratory for Radio Astronomy of CAS。
文摘In deep space exploration,it is necessary to improve the accuracy of frequency measurement to meet the requirements of precise orbit determination and various scientific studies.A phase detector is one of the key modules that restricts the tracking performance of phase-locked loop(PLL).Based on the phase relationship between adjacent signals in the time domain,a novel phase detector is presented to replace the arctangent phase detector.The new PLL,which is a closed loop signal correlation algorithm,shows good performance in tracking signals with high precision and the tracking accuracy of frequency of1 second integration is close to Cramer-Rao lower bound(CRLB)when setting proper parameters.Actual data processing results further illustrate the excellent performance of the novel PLL.
文摘In this paper, a new strategy of switchable CMOS phase-locked loop frequency synthesizer is proposed to increase its tuning range. The switchable PLL which integrates two phase-locked loops with different tuning frequencies are designed and fabricated in 0.5 μm n-well CMOS process. Cadence/Spectre simulations show that the frequency range of the switchable phased-locked loop is between 320 MHz to 1.15 GHz. The experimental results show that the RMS jitter of the phase-locked loop changes from 26 ps to 123 ps as output frequency varies. For 700 MHz carrier frequency, the phase noise of the phase-locked loop reaches as low as ?81 dBc/Hz at 10 kHz offset frequency and ?104 dBc/Hz at 1 MHz offset frequency. A device degradation model due to hot carrier effects has been used to analyze the jitter and phase noise performance in an open loop voltage-controlled oscillator. The oscillation frequency of the voltage-controlled oscillator decreases by approximately 100 to 200 MHz versus the bias voltage and the RMS jitter increases by 40 ps under different phase-locked loop output frequencies after 4 hours of stress time.
