Effect of electromagnetic and ultrasonic cast rolling on microstructure and properties of 1050 aluminum substrate for presensitized plate

The 1050 aluminum alloy strip was prepared by means of electromagnetic and ultrasonic cast rolling on the modified asymmetric twin roll caster, and then the aluminum substrate for presensitized plate was prepared through cold rolling and annealing.The effects of electromagnetic and ultrasonic cast rolling on microstructure, mechanical properties, surface roughness and electrolytic corrosion properties of 1050 aluminum substrate were studied. The results show that electromagnetic and ultrasonic cast rolling can decrease the average crystallite size of aluminum substrate by 5 μm, increase the crystal boundaries with uniform distribution, and make the second-phase particles with smaller size distributed dispersively in the substrate, meanwhile, it can increase the tensile strength, elongation and micro-hardness by 4.58%, 9.85% and HV 2, respectively, reduce the surface roughness, make the surface appearance more even, electrolytic corrosion polarization curve of aluminum substrate more smooth and the surface corrosion pits with regular shape more dispersive.

Grain refinement of Mg-Al alloys by optimization of process parameters based on three-dimensional finite element modeling of roll casting

To study the influence of roll casting process parameters on temperature and thermal-stress fields for the AZ31 magnesium alloy sheets,three-dimensional geometric and 3D finite element models for roll casting were established based on the symmetry of roll casting by ANSYS software.Meshing method and smart-sizing algorithm were used to divide finite element mesh in ANSYS software.A series of researches on the temperature and stress distributions during solidification process with different process parameters were done by 3D finite element method.The temperatures of both the liquid-solid two-phase zone and liquid phase zone were elevated with increasing pouring temperature.With the heat transfer coefficient increasing,the two-phase region for liquid-solid becomes smaller.With the pouring temperature increasing and the increase of casting speed,the length of two-phase zone rises.The optimized of process parameters（casting speed 2 m/min,pouring temperature 640 ℃ and heat transfer coefficient 15 kW/（m2·℃） with the water pouring at roller exit was used to produce magnesium alloy AZ31 sheet,and equiaxed grains with the average grain size of 50 μm were achieved after roll casting.The simulation results give better understanding of the temperature variation in phase transformation zone and the formation mechanism of hot cracks in plates during roll casting and help to design the optimized process parameters of roll casting for Mg alloy.

New Technique of Casting-rolling Strips for Semi-solid Magnesium Alloys

The conjugation of semi-solid process technique and casting-rolling technique applied to produce the magnesium strips was studied. The semi-solid slurry has been prepared continuously by the mechanical method and its temperature was controlled strictly at the same time. AZ91D and AZ31 casting magnesium alloys were applied to the experiment. The casting-rolling strips with non-dendritic structure were obtained and its main mechanical property is better. The process ability of the casting-rolling strips was studied. It is significative to link the semi-solid process techniques and casting-rolling techniques, through which we can get high quality magnesium alloy strips with non-dendritic structure and improve the overall properties of the products.

Effects of ultrasonic treatment on structure of roll casting aluminum strip

The experiment of ultrasonic treatment of roll casting aluminum strip on plane twin-roll cast-roller with double-heads ultrasonic tools was carried out, and the metallographic structure of the roll casting aluminum strip treated by ultrasonic was studied. The results show that ultrasonic treatment can refine the grain of the roll casting aluminum strips and make the structure of the strips more homogeneous. The effect is the best when the power of ultrasonic is 300 W and the incident angle of the guide rod is 45、. The mechanism of acoustic cavitations and acoustic flow on grain refinement was also discussed. The heat effect of intensity ultrasonic was studied. The present problems during ultrasonic roll casting process, such as the imperfect cooling system, the inaccurate calculation of ultrasonic energy, and the shape and position of the guide rod to be improved were pointed out.

Progress in twin roll casting of magnesium alloys: A review

Twin roll casting was commercialized for a strip production from ferrous and non-ferrous alloys in the 1950 s;however,its application to magnesium has proven difficult and still creates major challenges.This report describes global efforts in expanding manufacturing capabilities of magnesium sheet through twin roll casting path,offering many benefits,including a reduction in number of processing steps and energy savings.In addition to hardware design,alloy transformation during processing,product microstructure and properties,examples of successful solutions along with present technology and knowledge limitations are discussed.A particular attention is paid to developments at Canmet MATERIALS,having the only in North America pilot scale twin roll casting facility,devoted to magnesium.Efforts are described that aim at design of new magnesium alloys,which could take advantage of unique processing conditions during twin roll casting and contribute to the overall progress in magnesium sheet manufacturing.

Recrystallization behavior of cold rolled Al-Zn-Mg-Cu fabricated by twin roll casting

The Al-Zn-Mg-Cu alloy strip can be successfully fabricated by twin roll casting. In order to determine the effect of thickness reduction and heat treatment temperature on the recrystallization behavior, the strips were rolled and subsequently heat treated under various conditions. As a result, a fine grained microstructure （average grain size -13 μm, average grain aspect ratio -1.7） and high mechanical properties （UTS ≥360 MPa, δ ≥20%） were obtained by cold rolling with thickness reduction of 60% and heat treatment at 500 ℃ for 1 h. Also, the effect of the microstructure on mechanical properties of the Al-Zn-Mg-Cu alloy strip was discussed. Consequently, the low cost and high strength Al-Zn-Mg-Cu alloy sheet can be fabricated by twin roll casting by proper thermo-mechanical processes.

3D stress simulation and parameter design during twin-roll casting of 304 stainless steel based on the Anand model

This study first investigated cracks on the surface of an actual steel strip. Formulating the Anand model in ANSYS software, we then simulated the stress field in the molten pool of type 304 stainless steel during the twin-roll casting process. Parameters affecting the stress distribution in the molten pool were analyzed in detail and optimized. After twin-roll casting, a large number of transgranular and intergranular cracks resided on the surface of the thin steel strip, and followed a tortuous path. In the molten pool, stress was enhanced at the exit and at the roller contact positions. The stress at the exit decreased with increasing casting speed and pouring temperature. To ensure high quality of the fabricated strips, the casting speed and pouring temperature should be controlled above 0.7 m/s and 1520℃, respectively.

Influence of roll speed difference on microstructure, texture and mechanical properties of 7075 aluminum plates produced via combined continuous casting and rolling process

The influences of the dissimilarity in the roll speeds on the microstructure, texture and mechanical properties of 7075 aluminum plates produced via combined continuous casting and rolling(CCCR) process were investigated. Several experiments were conducted with three different upper/lower roll rotational speed ratios(ω/ω0, ω is the upper roll rotational speed and ω0 is the lower roll rotational speed), namely 1:1, 1:1.2 and 1:1.4. It was found that the greatest dissimilarity in the roll speed(ω/ω0=1:1.4) improved the yield strength and ultimate tensile strength of 7075 Al plate in the rolling direction by 41.5% and 21.9%, respectively. Moreover, at a roll speed ratio of ω/ω0=1:1.4, the average grain size was decreased by 36% whereas the mean hardness of the transverse cross-section of the finally rolled plate was increased by about 9.2%. Texture studies also revealed that the more the difference in the roll speeds was, the greater the isotropy and the hardness of the final product were. Nevertheless, conducting CCCR operation with different roll speeds resulted in about 6% reduction in the elongation of the deformed plate.

Effect of asymmetric rolling process on the microstructure,mechanical properties and texture of AZ31 magnesium alloys sheets produced by twin roll casting technique

Symmetric rolling(SR)and asymmetric rolling(ASR)processes were carried out on 6 mm thick AZ31 magnesium alloy sheets that were produced by twin roll casting(TRC)technique.Before rolling processes,sheets were heat treated in order to obtain a homogenized microstructure.In this study,for the ASR process the rolling speed ratio between upper roller and lower was selected as 1.25.Both SR and ASR processes were utilized with 40%reduction per passes using 2 pass schedule for a total reduction ratio of 0.67.Symmetric and asymmetric rolled sheets were characterized using optical microscopy(OM),scanning electron microscopy(SEM)and transmission electron microscopy(TEM)techniques.Texture measurements were performed by using X-ray diffraction(XRD)technique and mechanical properties were investigated by tensile tests and also hardness measurements.

Creep Behaviors of DA Casting and Rolling GH4169 Superalloy

After the billet of Casting and Rolling GH4169 alloy was directly aged (DA) treated at 720 ℃ and 620 ℃, creep behavior and deformed features of the alloy were investigated by means of the measurement of creep curves and microstructure observation. Results show that the DA Casting and Rolling GH4169 Superalloy displays a lower strain rate during creep and longer lifetimes under the condition of the applied stress of 700 MPa at 650 ℃ , the creep lifetimes of the alloy decrease to 127 h as temperature is elevated to 660 ℃ , and therefore the alloy exhibits an obvious sensitivity of the applied temperatures. During creep, the deformation mechanism of the alloy is thought to be the twinning deformation and slipping of dislocation within the twinning regions. Thereinto, the dislocation slipping of the single and double orientations occur within the twins. As creep enters the tertiary steady state stage, the micro-crack appears on the grains boundaries along the direction vertical to the applied stress axis, and expands along the grain boundary up to fracture.

Mathematical modeling of thermo-mechanical behavior of strip during twin roll casting of an AZ31 magnesium alloy

The effect of set-back distance on the thermo-mechanical behavior of the strip during twin roll casting(TRC)of an AZ31 magnesium alloy was modeled using finite element method(FEM).Model validation was done by comparing the predicted and measured exit strip surface temperature as well as the secondary dendrite arm spacing(SDAS)through the thickness of the sheet to those measured during experiments.Model results showed as the set-back distance increases,the strip exit temperature decreases and the solidification front moves toward the entry of the roll gap.The cast strip also experiences more plastic deformation and consequently,the normal stress on the strip surface and effective strain at the strip center-line increase.Moreover,higher separating forces were predicted for longer set-back distances.Model predictions showed that changing the set-back distance by varying the final thickness has a more significant effect on the temperature and stress-strain fields than altering the nozzle opening height.

Research and development of transnormal twin roll-casting technology

Focusing on the research and development of transnormal twin roll casting technology and modeling and simulation of twin roll casting process, the progresses made in China to date in the following aspects were introduced, the analysis and calculation of heat conductance both in contact zone between the strip and the outside of the roller and the inside of the roller; the 3 D numerical simulation of molten aluminum flow in feed tip nozzle; the research of the effects of electromagnetic fields on textures and mechanical properties of casting rolling strip, and the modeling and simulation of twin roll casting process including the methods of modeling and some significant results.

Numerical simulation of the temperature fields of stainless steel with different roller parameters during twin-roll strip casting

The temperature field of stainless steel during twin-roll strip casting was simulated by experiment and a finite element （FE） model. By comparing the measured result with the simulated values, it is found that they fit close to each other, which indicates this FE model is effective. Based on this model, the effects of roll gap （t） and roll radius （R） on solidification were simulated. The simulated results give the relationship between t or R and the position of the freezing point. The larger the t is and the smaller the R is, the closer the position of the freezing point is to the exit.

EFFECTS OF ELECTROMAGNETIC FIELD ON CASTING-ROLLING STRIP BREAKDOWNS

ＥＦＦＥＣＴＳＯＦＥＬＥＣＴＲＯＭＡＧＮＥＴＩＣＦＩＥＬＤＯＮＣＡＳＴＩＮＧＲＯＬＬＩＮＧＳＴＲＩＰＢＲＥＡＫＤＯＷＮＳ①ＭａｏＤａｈｅｎｇＣｏｌｅｇｅｏｆＥｌｅｃｔｒｏｍｅｃｈａｎｉｃａｌＥｎｇｉｎｅｒｉｎｇ，ＣｅｎｔｒａｌＳｏｕｔｈＵｎｉｖｅｒ...

Mechanism and simulation of external cooling in aluminum casting-rolling process

External cooling technology is one of the key technologies to realize fast-casting-rolling process of aluminum, i.e. using compulsive cooling on the external surface of rollers and aluminum plate to improve the cooling ability of system, increase casting-rolling speed, and enhance the quality of aluminum plate. Heat transfer model of casting-rolling process was proposed and the characteristics of the temperature field of roller-plate system were analyzed. The influences of external cooling surface of the plate and the roller on the temperature field of the roller and the aluminum plate and the casting-rolling speed were discussed, and the relationship between external cooling and internal cooling were also analyzed. Experiment results show that, with the increase of casting-rolling speed, the influence of cooling plate surface on increasing casting-rolling speed was gradually decreased, but that of cooling roller surface was enhanced. Different mechanisms of external cooling plate surface and roller surface for improving casting-rolling speed account for this phenomenon.

3-D Numerical Simulation of the Electromagnetic Dam of Twin Roll Casting using Edge Element Method

The 3-dimension numerical simulation study on the electromagnetic dam used in the twin roll caster has been performed by using the edge element method. It was found that the materials and structures of the roll collars have great influence on the distribution of the magnetic flux density, eddy current density and the electromagnetic force in the molten pool. The conductive collars make the magnetic flux density decreased in the molten pool, but it also makes the magnetic force more uniformly, and the force in the low part of the molten pool where needs greater force have increased some what. The conductive collars make the EMD device more effective than the nonconductive collars.

Multi-scale Simulation on Bonding Mechanism of Solid-Liquid Cast-Rolling of Cu/Al Cladding Strip based on FEM and MD

To explore the complex thermal-mechanical-chemical behavior in the solid-liquid cast-roll bonding(SLCRB) of Cu/Al cladding strip, numerical simulations were conducted from both macro and micro scales. In macro-scale, with birth and death element method, a thermo-mechanical coupled finite element model(FEM) was set up to explore the temperature and contact pressure distribution at the Cu/Al bonding interface in the SLCRB process. Taking these macro-scale simulation results as boundary conditions, we simulated the atom diffusion law of the bonding interface by molecular dynamics(MD) in micro-scale. The results indicate that the temperature in Cu/Al bonding interface deceases from 700 to 320 ℃ from the entrance to the exit of caster, and the peak of contact pressure reaches up to 140 MPa. The interfacial diffusion thickness depends on temperature and rolling reduction, higher temperature results in larger thickness, and the rolling reduction below kiss point leads to significant elongation deformation of cladding strip which yields more newborn interface with fresh metal and make the diffusion layer thinner. The surface roughness of Cu strip was found to be benefit to atoms diffusion in the Cu/Al bonding interface. Meanwhile, combined with the SEM-EDS observation on the microstructure and composition in the bonding interface of the experimental samples acquired from the castrolling bite, it is revealed that the rolling reduction and severe elongation deformation in the solid-solid contact zone below kiss point guarantee the satisfactory metallurgical bonding with thin and smooth diffusion layer. The bonding mechanisms of reactive diffusion, mechanical interlocking and crack bonding are proved to coexist in the SLCRB process.

FEM Analysis of Physical Field in Level Rolling Process of Inversion Casting by ANSYS Program

The strain physical field in level rolling process of inversion casting was analyzed by ANSYS program.Plastic strain,stress and displacement were gained.The results show that only surface strain takes place) the maximum stress exists in the geometrical deformation zone;In the deformation transition zone and the part leaving the rollers,different stress exists.The rolling force estimated with ANSYS program corresponds to those measured.

Simulation of Fluid Flow, Heat Transfer and Micro-Segregation in Twin-roll Strip Casting of Stainless Steel

In twin-roll strip casting process, metal flow and temperature distribution in the molten pool directly affect the stability of the process and the quality of products. In this paper, a 3D coupled thermal-flow fenite element modeling （FEM） simulation for twin-roll strip casting of stainless steel was performed. Influences of the pouring temperature and casting speed on the temperature fields were obtained from the numerical simulation. The micro-segregation of the solutes during the strip casting process of stainless steel was also simulated. A developed micro-segregation model was used to calculate the micro-segregation of solutes in twin-roll casting of stainless steel. The relationship between the solidus fraction in solidification and temperature was given, which was used to determine the LIT （liquid impermeable temperature）, ZST （zero strength temperature） and ZDT （zero ductility temperature） in the period of non-equilibrium solidification. The effect of temperature on the micro-segregation was discussed. According to the computational results, the solidification completion temperature in the twin-roll strip casting of stainless steel was then determined, which can provide a basis for controlling the location of solidification completion temperature and analysing the crack of the casting strip.

Simulation of microstructures in solidification of aluminum twin-roll casting based on CA

The microstructures in the solidification process of aluminum twin-roll casting was simulated based on CA(Cellular Automation Method),and the nucleation model based on the normal distribution and KUZR-GIOVANOLS-TRIVEDI(KGT) growth model were used in the calculation. FDM(Finite Difference Method) combined with relative motion was used,and dynamic evolution of microstructures in the process of aluminum twin-roll casting was achieved. Visual Fortran programming language was adopted to calculate and realize the image post-processing. Moreover,the effect of different casting process parameters on the formation of the microstructures was simulated. The results are helpful to explaining the dendritic segregation and size segregation as well as shrinkage-porosity defects. Columnar grains mainly distribute near the casting roller while equiaxed grains distributed far away from the casting roller.