High Cr white cast iron/carbon steel bimetal liner by lost foam casting with liquid-liquid composite process

Liners in wet ball mill for mineral processing industry must bear abrasive wear and corrosive wear, and consequently,the service life of the liner made from traditional materials,such as Hadfield steel and alloyed steels,is typically less than ten months.Bimetal liner,made from high Cr white cast iron and carbon steel,has been successfully developed by using liquid-liquid composite lost foam casting process.The microstructure and interface of the composite were analyzed using optical microscope,SEM,EDX and XRD.Micrographs indicate that the boundary of bimetal combination regions is staggered like dogtooth,two liquid metals are not mixed,and the interface presents excellent metallurgical bonding state.After heat treatment,the composite liner specimens have shown excellent properties,including hardness>61 HRC,fracture toughnessα k >16.5 J·cm-2 and bending strength >1,600 MPa.Wear comparison was made between the bimetal composite liner and alloyed steel liner in an industrial hematite ball mill of WISCO,and the results of eight-month test in wet grinding environment have proved that the service life of the bimetal composite liner is three times as long as that of the alloyed steel liner.

Effect of vibration frequency on primary phase and properties of grey cast iron fabricated by lost foam casting

The properties of gray cast iron(GCI)are affected by density of matrix,size of flake graphite and primary austenite.In this paper,the Y-type specimen of GCI was prepared by lost foam casting(LFC)with and without vibration,and the influence of vibration frequency on the density of matrix,size of primary phase,and properties of the GCI was studied.The results show that the length of the flake graphite and the size of the primary austenite in GCI firstly decrease and then increase with the increase of the vibration frequency.With a vibration frequency of 35 Hz,the length of the flake graphite is the shortest,the primary austenite is the finest and the density of the matrix is the highest.In addition,the tensile strength,elongation and hardness of the GCI firstly increase and then decrease with the increase of the vibration frequency,due to the refinement of the primary phase and the increase of the matrix density.In order to analyze the refinement mechanism of the primary phase of the GCI fabricated by the LFC with vibration,the solidification temperature fields of the GCI fabricated by the LFC with the vibration frequency of 0 and 35 Hz were measured.The results show that the vibration reduces the eutectic point of the GCI and increases the supercooling degree during the eutectic transformation.As a result,the length of the flake graphite and the size of the primary austenite in GCI fabricated by LFC with the vibration frequency of 35 Hz decrease.

Numerical Simulation of Shrinkage Cavity Formation in Spheroidal Graphite Iron Castings Based on Micro Modeling

A micro-modeling method (MM) for the quantitative prediction of the shrinkage cavity formation in SGiron castings is proposed. The mathematical models describing the volume changes during the solidification ofspheroidal graphite cast iron are established based on the models of solidification kinetics. The shrinkage cavityformation of T-shaped SG iron castings is calculated with MM method. The calculated results are compared with theexperimental results. It is shown that the predicted size, shape and distribution of shrinkage cavity by MM methodare in good agreement with the measured results.

Centrifugal Casting of High Speed Steel/Nodular Cast Iron Compound Roll Collar

The centrifugal casting of compound HSS/nodular cast iron roll collar was studied,and the factors affecting transition zone quality were analyzed.The pouring temperature and interval in pouring are the main factors affecting transition zone quality.By controlling process parameter and flux adding during casting,high quality roll collar was obtained.The cause,why in the casting of HSS part,segregation appears easily,was analyzed and the countermeasure eliminating segregation was put forward,the measure eliminating heat treatment crackling was also put forward.

Microstructure and Property of Hypereutectic High Chromium Cast Iron Prepared by Slope Cooling Body-Centrifugal Casting Method

In this paper, the ring-type ingot of hypereutectic high Cr cast iron was obtained by slope cooling bodycentrifugal casting method （SC-CCM）, and its microstructure and impact toughness were investigated, respectively. The results indicated that, first, the primary carbides in the microstructure are prominently finer than those in the hypereutectic high Cr cast iron prepared by conventional casting method. Second, in the ring-type ingot, the primary carbides near radial outer field are finer than those near radial inner field; furthermore, there is dividing field in the microstructure. Finally, the impact toughness values of the specimens impacted on the radial outer face and on the radial inner face are improved respectively about 36% and 138% more than that of the hypereutectic high Cr one prepared by conventional casting method.

Fabrication of plain carbon steel/high chromium white cast iron bimetal by a liquid–solid composite casting process

High-chromium white cast iron （HCWCI） is one of the most widely used engineering materials in the mining and cement industries. However, in some components, such as the pulverizer plates of ash mills, the poor machinability of HCWCI creates difficulties. The bimetal casting technique is a suitable method for improving the machinability of HCWCI by joining an easily machined layer of plain carbon steel （PCS） to its hard part. In this study, the possibility of PCS/HCWCI bimetal casting was investigated using sand casting. The investigation was conducted by optical and electron microscopy and non-destructive, impact toughness, and tensile tests. The hardness and chemical composition profiles on both sides of the interface were plotted in this study. The results indicated that a conventional and low-cost casting technique could be a reliable method for producing PCSYdCWCI bimetal. The interfacial microstructure comprised two distinct lay- ers： a very fine, partially spheroidized pearlite layer and a coarse full pearlite layer. Moreover, characterization of the microstructure revealed that the interface was free of defects.

Microstructural and mechanical characteristics of Al-alloyed ductile iron upon casting and annealing

Ductile iron containing 6.16wt% A1 was developed to investigate the effects of aluminum on both its microstructure and hardness. It was found that aluminum not only increases the nodule count and pearlite content but also improves the hardness in both sand mold and metal mold castings. Annealing treatments were conducted to attain a homogenous microstructure and improve high-temperature serviceabil- ity. A ferrite/carbide or ferritic matrix was gained depending on the annealing temperature. It is also discovered that annealing has inverse in- fluences on the hardness of the bulk alloy and the ferrite phase. Although it causes a small decrease in the bulk hardness of the specimens, it leads to an increase in the microhardness of the ferrite. Micro-segregation of the alloying elements was also investigated by means of electron probe micro-analysis for the specimens with different annealing durations and the as-cast specimen as well. An optimum annealing time was proposed to result in the least amount of micro-segregation of aluminum and silicon between graphite nodules.

Influence of shrinkage porosity on fatigue performance of iron castings and life estimation method

Shrinkage porosity exists more or less in heavy castings, and it plays an important role in the fatigue behavior of cast materials. In this study, fatigue tests were carried out on the QT400-18 cast iron specimens containing random degrees of shrinkage porosity defect. Experimental results showed that the order of magnitude of life scattered from 103 to 106 cycles when the shrinkage percentage ranged from 0.67% to 5.91%. SEM analyses were carried out on the shrinkage porosity region. The inter-granular discontinuous, micro cracks and inclusions interfered with the fatigue sliding or hindering process. The slip in shrinkage porosity region was not as orderly as the ordinary continuous medium. The shrinkage porosity area on fracture surface(SPAFS) and alternating stress intensity factor(ASIF) were applied to evaluate the tendency of residual life distribution; their relationship was fitted by negative exponent functions. Based on the intermediate variable of ASIF, a fatigue life prediction model of nodular cast iron containing shrinkage porosity defects was established. The modeling prediction was in agreement with the experimental results.

Microstructural analysis of EN-GJS-450-10 ductile cast iron via vibrational casting

EN-GJS-450-10 ductile cast iron was produced with and without vibration to evaluate microstructural features. To investigate the effect of vibration, a reference, and two different castings having amplitudes of 0.9 mm and 1.8 mm were cast with a fixed vibration frequency of 50 Hz. The nodule count (density), form (type), size distribution, nodularity, and the fraction of graphite, percentages of both ferrite and pearlite phases, length of ferrite shell, and pore, were evaluated via optical microscopy using an image analysis software. It is observed that the microstructure of the cast iron is more uniform by vibrational casting than that by non-vibrational casting. Additionally, mechanical vibration enhances nodule count and nodularity, also, more ferritic matrix could be obtained after the application of vibration. Nodule count and nodularity of vibrational casting with 1.8 mm amplitude increased from 226 nodule per mm2 and 80% to 311 nodule per mm2 and 86.5% of non-vibrational casting. Percentages of ferrite and graphite area dramatically improved from 24% and 16.5% for non-vibrational casting to 57% and 22.3% for vibrational casting with 1.8 mm amplitude, whereas the percentages of pearlite and pores decreased significantly from 56.1% and 5% to 20% and 1%, respectively.

A Mathematical Model for Predicting Shrinkage Defect of Ductile Iron Castings

The shrinkage defect of a ductile iron casting is attributed to the volume variations occurring in solidification, which consist of liquid contraction, solidification shrinkage, graphitization expansion, and mold cavity enlargement. Based on this understanding, a mathematical model for predicting the shrinkage defect of the casting is developed, in which the volume variations of the casting in soli- dification are numerically simulated, especially, the mold cavity enlargement is quantitatively calculated. Moreover, the reliability of the model is verified in production and experiment.

Determining the Thermal Conductivity in Walls of Cast Iron Castings by the Ultrasound Technique

Research results concerning the application of ultrasound technique for determining the averaged thermal conductivity in walls of castings produced of cast iron(solidifying in a steady system)containing carbon precipitates in a graphite form,are presented in the hereby paper.Investigations concern castings of unalloyed cast iron.The influence of the form of graphite precipitates on the cast iron thermal conductivity as well as on the propagation velocity of the ultrasound wave,including the longitudinal wave velocity CL,was investigated in the study.The influence of the graphite form,described by the shape indicator(f),on the thermal conductivity(l)(determined on samples by the steady heat flow method)as well as the influence of this indicator(f)on the wave propagation velocity(CL),was investigated.A series of melts of cast iron,of the near eutectic chemical composition,were performed.Magnesium introduced in a wide range,allowed obtaining various graphite forms from flake,via mixed,vermicular to nodular.Dependences:l=f(CL),CL=f(f)were determined and at the final phase the empirical dependencel=f(CL)was also determined.The thermal conductivity and ultrasound wave velocity were tested on the same samples.The thermal conductivity coefficient of cast iron(l)was changing in a wide range from approximately 32 to 46 W/s·m,while the wave velocity CL respectively:from approximately 4,300 to 5,800 m/s.The empirical dependencel=f(CL),determined in the described variability ranges,is of a linear character and the correlation level equals:R2=0.87.The validation of the experimental results was performed on cast iron castings of slag ladles,since they are required to be of a good thermal conductivity.The possibility of assessing the thermal conductivity directly in walls of such castings by means of non-destructive ultrasound method,was confirmed.The real thermal conductivity determined in the walls of the castings is used to simulate the heating and cooling process of slag ladles,ingot molds and similar structures,which was one of the main objectives of the research.

Interface characteristics and wear resistance of Ni-B_(4)C plated ZTA reinforced high chromium cast iron composite

A chemical composite plating of Ni-B_(4)C was used to prepare the surface-modified zirconia toughened alumina(ZTA)ceramic particles.The ceramic preforms were prepared by the plated ZTA and sodium silicate solution binder,followed by casting infiltration to prepare the ZTA particles reinforced high chromium cast iron(HCCI)composites.The result reveals that a distinct interface layer forms at the ZTA/HCCI interface,which consists of phases of ZrB_(2),FeB,Fe_(2)B,and NaSiO_(4).The interfacial wettability between ZTA and HCCI is improved by the diffusion and reaction of Ni and B_(4)C.The wear test reveals that the Ni-B_(4)C plated ZTA particles can effectively improve the wear resistance of the ZTA/HCCI composite,and the wear rate of the composite is decreased to 11.6%of HCCI.

Microstructure and properties of LZQT600-3 HCCDIBs for plunger pump cylinder

It is important to improve the comprehensive performance of the ductile iron bars(DIBs)for the cylinder block of the extra high pressure hydraulic plunger pump and accelerate the industrial application.In this work,the LZQT600-3 DIBs with the diameter of 145 mm were prepared by the horizontal continuous casting(HCC)process,that is,LZQT600-3 HCCDIBs.The microstructure and room temperature tensile properties of different sections[left-edge(surface layer),left-1/2R(left half of the radius),and the center of the HCCDIBs]were studied.The results show that the spheroidization of LZQT600-3 HCCDIBs matrix from the left-edge,left-1/2R to the center is at nodulizing grade II and above.As the cooling rate gradually decreases from surface to the center of the HCCIBs,the number of spheroidized graphite is gradually reduced,the size is gradually increased,the shape factor is decreased,and the pearlite content and lamellate spacing are increased.Along the horizontal direction of the section,the hardness of the material is distributed symmetrically around the center of the HCCDIBs.In the vertical direction,the hardness distribution in the center of the HCCDIBs is asymmetrical due to the gravity during the solidification process.Therefore,the microstructure in the lower part of the section solidifies relatively quickly.The left-edge has the best tensile mechanical properties,and the ultimate tensile strength,yield tensile strength and elongation are 597.3 MPa,418.5 MPa and 9.6%,respectively.The tensile fracture belongs to the ductile-brittle hybrid fracture.The comprehensive performances of LZQT600-3 HCCDIBs meet the actual application requirements of ultra-high pressure hydraulic plunger pump cylinder.

Effects of Alloying Elements on the Microstructures and Mechanical Properties of Heavy Section Ductile Cast Iron

The effects of alloying elements on the as-cast microstructures and mechanical properties of heavy section ductile cast iron were investigated to develop press die material having high strength and high ductility. Measurements of ultimate tensile strength, 0.2% proof strength, elongation and unnotched Charpy impact energy are presented as a function of alloy amounts within 0.25 to 0.75 wt pct range. Hardness is measured on the broken tensile specimens. The small additions of Mo, Cu, Ni and Cr changed the as-cast mechanical properties owing to the different as-cast matrix microstructures. The ferrite matrix of Mo and Ni alloyed cast iron exhibits low strength and hardness as well as high elongation and impact energy. The increase in Mo and Ni contents developed some fractions of pearlite structures near the austenite eutectic cell boundaries, which caused the elongation and impact energy to drop in a small range. Adding Cu and Cr elements rapidly changed the ferrite matrix into pearlite matrix, so strength and hardness were significantly increased. As more Mo and Cr were added, the size and fraction of primary carbides in the eutectic cell boundaries increased through the segregation of these elements into the intercellular boundaries.

Properties of Cross-Rolled Low Alloy White Cast Iron Grinding Ball

The low-energy, multi-impact fracture resistance and the abrasiveness of the cross-rolled low alloy white cast iron grinding balls were studied after heat treatments at residual rolling temperature. Moreover, the means by which they are damaged and characters of the wear surface were analyzed. The results show that high resistance to impact fracture and high abrasiveness can be achieved after appropriate heat treatment at residual rolling temperature. This kind of heat treatment technology has several advantages under low impact and hard abrasive. These results are very useful for determining the optimized heat treatment technology at residual rolling temperatures.

Heat Treatment Effect on Microstructure, Hardness and Wear Resistance of Cr26 White Cast Iron

High chromium cast iron（HCCI） is taken as material of coal water slurry pump impeller, but it is susceptible to produce serious abrasive wear and erosion wear because of souring of hard coal particles. The research on optimization of heat treatments to improve abrasive wear properties of HCCI is insufficient, so effect of heat treatments on the microstructure, hardness, toughness, and wear resistance of Cr26 HCCI is investigated to determine the optimal heat treatment process for HCCI. A series of heat treatments are employed. The microstructures of HCCI specimens are examined by using optical microscopy and scanning electron microscopy. The hardness and impact fracture toughness of as-cast and heat treated specimens are measured. The wear tests are assessed by a Type M200 ring-on block wear tester. The results show the following： With increase of the quenching temperature from 950 ℃ to 1050 ℃, the hardness of Cr26 HCCI increased to a certain value, kept for a time and then decreased. The optimal heat treatment process is 2 h quenching treatment at 1000 ℃, followed by a subsequent 2 h tempering at 400 ℃. The hardness of HCCI is related to the precipitation and redissolution of secondary carbides in the process of heat treatment. The subsequent tempering treatment would result in a slight decrease of hardness but increase of toughness. The wear resistance is much related to the ＂supporting＂ effect of the matrix and the ＂protective＂ effect of the hard carbide embedded in the matrix, and the wear resistance is further dependent on the hardness and the toughness of the matrix. This research can provide an important insight on developing an optimized heat treatment method to improve the wear resistance of HCCI.

Effect of Cryogenic Treatment on Property of 14Cr2Mn2V High Chromium Cast Iron Subjected to Subcritical Treatment

Effect of cryogenic treatment on the microstructure, hardening behavior and abrasion resistance of 14Cr2Mn2V high chromium cast iron （HCCI） subjected to subcritical treatment was investigated. The results show that cryogenic treatment after subcritical treatment can obviously improve the hardness and abrasion resistance of HCCI because abundant retained austenite is transformed into martensite and fine secondary carbides E（Fe, Cr）23 C6 ] precipitate. The amount of martensite and precipitated secondary carbide in HCCI experiencing subcritical treatment followed by cryogenic treatment was more than that experiencing the subcritical treatment followed by air cooling. When the abrasion resistance of HCCI reaches the maximum, its microstructure contains about 15 % retained austenite. Cryogenic treatment can further reduce the austenite content but the retained austenite cannot be transformed in to martensite completely.

Gray Cast Iron With Directional Graphite Flakes Produced by Cylinder Covered Compression Process

A new plastic deformation process for gray cast iron named cylinder covered compression （CCC） was developed. By CCC process, gray cast iron （GCI） specimens, which are embedded in steel cylinders, were hot compressed up to 80% reduction in height without the cracking problem. It was clearly observed that the uniform distribution of directional graphite flakes appeared after more than 45 % reduction hot compression. The strength, ductility, and microhardness of GCI after 80% reduction deformation were significantly enhanced： the tensile strength varied from 117 MPa to 249 MPa, while the total elongation varied from 0 to 5.2%, and the microhardness varied from 153 HV to 217 HV. It was shown that the tensile fracture surface presented ductility characters after more than 45% reduction hot deformation.

Effects of Rare Earths and Al on Structure and Performance of High Chromium Cast Iron Containing Wolfram

Effects of RE and Al on the structure, impact toughness, hardness, and wear resistance of high chromium cast iron containing wolfram were investigated. The results show that without modification the volume fraction of austenite is high and the carbide appears to be thick lath and the grain size is relatively large; proper modification using RE combined with Al can reduce volume fraction of residual austenite in the as-cast structure obviously, refine grain size of primary austenite notably, and make the morphology of carbide changing from thick lath to thin lath, rosette, and feather-like modification can also increase hardness, wear resistance and impact toughness of cast iron.

Effect of scanning speed during PTA remelting treatment on the microstructure and wear resistance of nodular cast iron

The surface of nodular cast iron （NCI） with a ferrite substrate was rapidly remelted and solidified by plasma transferred arc （PTA） to induce a chilled structure with high hardness and favorable wear resistance. The effect of scanning speed on the microstructure, micro-hardness distribution, and wear properties of PTA-remelted specimens was systematically investigated. Microstructural characterization in-dicated that the PTA remelting treatment could dissolve most graphite nodules and that the crystallized primary austenite dendrites were transformed into cementite, martensite, an interdendritic network of ledeburite eutectic, and certain residual austenite during rapid solidifica-tion. The dimensions of the remelted zone and its dendrites increase with decreased scanning speed. The microhardness of the remelted zone varied in the range of 650 HV0.2 to 820 HV0.2, which is approximately 2.3-3.1 times higher than the hardness of the substrate. The wear re-sistance of NCI was also significantly improved after the PTA remelting treatment.