CATIONIC POLYMERIZATION OF ISOBUTYLENE COINITIATED BY AICI_3 IN THE PRESENCE OF ETHYL BENZOATE

The cationic polymerizations of isobutylene （IB） coinitiated by AlCl3 were carried out in solvent mixture of nhexane/methylene dichloride （n-hex/CH2Cl2） of 60/40 V/V in the presence of ethyl benzoate （EB） at various temperatures range from -80℃ to -30℃. The effects of EB concentration （[EB]） and polymerization temperature on monomer conversion, weight-average molecular weight （Mw） and molecular weight distribution （MWD, Mw/Mn） of polyisobutylene （PIB） products were investigated. The rate of polymerization decreased while Mw of PIB products increased with increasing [EB]. The polymers with high molecular weight could be prepared in the presence of a suitable amount of EB. Significantly, the polymers with high Mw of 80.2 × 10^4 and 65.4 × 10^4 could be produced at -80℃ and -70℃ at [EB] = 0.24 × 10^3 mol/L respectively, which were much higher than that （Mw = 57.9 × 10^4） of PIB prepared at -100℃ in the absence ofEB. A simple but effective method for preparing the high molecular weight polyisobutylenes was developed in this work. It has been also found that the activation energy for propagation （Ep） depended on the polymerization temperature range in the presence of EB. An obvious inflection of the linear plots of lnXn versus 1/Tp occurred at the temperature range from -60℃ to -50℃ at four different concentrations of EB from 0.19 × 10^3 mol/L to 0.33× 10^3 tool/L, and thus the inflection temperature （Tinf） was in the range of -60℃ to -50℃. When [EB] was in the range of 0.24 × 10^3 mol/L to 0.33× 10^3 mol/L, Ep was determined to be around -12 kJ/mol when the polymerization was carried out at temperatures from -80℃ to Tinf and to be around -28 kJ/mol at temperatures from Tinf to -15℃ respectively.

SYNTHESIS OF POLYISOBUTYLENE WITH SEC-ARYLAMINO TERMINAL GROUP BY COMBINATION OF CATIONIC POLYMERIZATION WITH ALKYLATION

The highly reactive polyisobutylenes(PIBs) withα-double bonds(87.5 mol%) or tert-chloro(tert-Cl) groups(95 mol%) could be prepared via the cationic polymerization of isobutylene(IB) coinitiated by BF_3 or TiCl_4 respectively.The Friedel-Crafts alkylation of diphenylamine(DPA) with the highly reactive PIB withα-double bonds was further conducted under different conditions,such as at different alkylation temperature,in the mixed solvents of CH_2Cl_2/n-hexane with different solvent polarity and at DPA concentr...

RESEARCH ON CATIONIC POLYMER WATER BASE DRILLING FLUIDS

Cationic polymer drilling fluid (CPDF) is a new water base drilling fluid in which high molecular weight (HMW) cationic polymer (CPAM) is an encapsulating and flocculating agent and organic quaternary ammonium compound (NW-1) acts as shale inhibitor. This paper describes the experimental results of cuttings recovery, particle size distribution layer spacing and Zeta potential, and discusses the inhibition of CPDF system and its major additives. The advantages of CPDF will be proved by its application in well LX-2.

Synthesis and Characterization of Star-branched Polyisobutylene by Combination of Anionic Polymerization and Cationic Polymerization

A star-shaped multifunctional styrene-isoprene copolymer was synthesized with n-BuLi as initiator, divinyl benzene as coupling agent, cyclobexane as solvent by living anionic polymerization. Using this polymer as grafting agent, a novel star-shaped branched polymer, containing several polyisobutylene, was prepared via cationic ~aolymerization. The star PS-b-PI and star-branched polyisobutylene were characterized by GPC, ＇HNMR and FT-IR, and the effects of different adding order and the amount of grafting agent were investigated.

STUDY ON THE CATIONIC POLYMERIZATION OF 1, 3-PENTADIENE INITIATED BY AlCl_3/ALKYL HALIDE SYSTEMS

The cationic polymerizations of 1, 3-pentadiene were initiated by AlCl_3 in n-hexaneat 30℃ in the presence of alkyl halides, i.e., tert-butyl chloride, tert-butyl bromide andisobutyl chloride. The effects of these halides on the polymer yield, molecular weight,crosslinking reaction, cyclization and polymer microstructure, have been investigated. Twomain side reactions, crosslinking and cyclization, were suppressed and reduced by theaddition of the halides. The proportion of 1, 4 units of polymer chains was increasedby the presence of the halides, which reduced the polymer yield and the molecular weightof polymers.

(CH_3)_3SiCl/TiCl_4 INITIATING SYSTEM FOR CATIONIC POLYMERIZATION OF 1,3-PENTADIENE

Cationic polymerizations of 1,3-pentadiene (PD) initiated by trimethylsilyl chloride (TMSCl) incombination with TiCl_4 were carried out in n-hexane at 30℃. The yield of polymer was greatly increased bythe addition of TMSCl, indicating that the TMSCl/TiCl_4 combination is an efficient initiating system for PDcationic polymerization. However, the introduction of TMSCl gave rise to a drop in the molecular weight ofthe polymer. Kinetic results demonstrated that the polymerization initiated by TMSCl/TiCl_4 is 4.5 times fasterthan that induced by TiCl_4 alone. Various ethers were used to mediate the TMSCl/TiCl_4 initiating system.Adding diphenyl ether could increase both the yield and molecular weight of the polymer. Structural evidenceillustrates that the polymerization is indeed initiated by TiCl_4 in combination with HCl resulting fromhydrolysis by adventitious water.

CATIONIC POLYMERIZATION OF 1,3—PENTADIENE INITIATED BY ORGANIC AZIDE/Et_2AlCl

The cationic polymerization of 1, 3-pentadiene was initiated by the organic azide/Et_2 AlClinitiating system in CH_2Cl_2 and n-hexane. The polymerizations were also carried out in parallelwith organic chloride/Et_2AlCl and Et_2 AlCl alone for comparison. The Et_2 AlCl- induced polymer-ization gives a low yield while the polymerization initiated by organic chloride/Et_2 AlCl producesmainly insoluble product. In contrast, the polymerization with azide/Et,AlCl has a high conver-sion and the resulting polymer having a high molecular weight is totally soluble. The SEC spectraof the polymers have clearly shown the differences between these initiating systems.

SYNTHESIS OF HIGH MOLECULAR WEIGHT POLYISOBUTYLENE VIA CATIONIC POLYMERIZATION AT ELEVATED TEMPERATURES

A novel simple but effective initiating system of H2O/AlCl3/veratrole （VE） has been developed to synthesize high molecular weight polyisobutylene （PIB） at elevated temperatures via cationic polymerization of isobutylene （IB） in solvent mixture of hexane/methylene dichloride （n-Hex/CH2Cl2 = 2/1, V/V）. VE played very important roles in decreasing cationicity of the growing chain ends, suppressing side reactions of chain transfer and termination during polymerization, leading to production of high molecular weight PIBs. PIBs with high yields, having very high weight-average molecular weight （Mw） of 1117000 and 370000 g/tool could be synthesized with H2O/AICl3/VE initiating system at VE concentration of 5.4 mmol/L at -80 and -60 ℃ respectively. Molecular weight of PIB increased remarkably with increasing VE concentration. The reaction order with respect to VE concentration was determined to be -3.52 via FTIR spectroscopy in combination with a diamond tipped attenuated total reflectance （ATR） immersion probe. The negative reaction order of VE was consistent with its retarding effect on IB polymerization by interacting with the propagating species. Molecular weight of PIB decreased with increasing polymerization temperature. The activation energy for polymerization degree （Eop） could be determined to be around -23 kJ/mol when VE concentration was 5.4 mmol/L or 6.4 mmol/L.

Cationic Ring Opening Polymerization of Octamethylcyclotetrasiloxane Initiated by Acid Treated Bentonite

Cationic ring opening polymerization of octamethylcyclotetrasiloxane （Da） initiated by acid treated bentonite was investigated. The experimental conditions were chosen on the basis of preliminary experiments.Higher temperature was found beneficial for the reaction process while stirring intensity beyond a certain level showed no obvious effect on the reaction rate. Polymers were characterized by Fourier transform infrared, proton nuclear magnetic resonance （IH-NMR） and gel perneation chromotography. The width of molecular mass distribution was found ranging between 1.2 and 1.4, which is extraordinarlly narrow compared with that of cationic polymerizations reported elsewhere （〉 1.9）. The results were believed due to the absence of free proton and counter ion which simplifies the polymerization process and the huge steric hindrance provided by bentonite particles which keeps the propagation of polysiloxane onto the surface of bentonite particles in a much more regular way. A feasible mechanism is proposed and seems to be supported well by experiments. Additionally, from the results of α, ω-dihydrogen terminated polysiloxanes prepared, the possibility of applying this potential environmentally friendly heterogeneous catalyst in industrial polymerization of cyclosiloxanes is anticipated.

Novel acid initiators for the rapid cationic polymerization of styrene in room temperature ionic liquids

Cationic polymerization of styrene has been achieved using several novel acidic initiators in room temperature ionic liquids (ILs) under mild reaction conditions to obtain polymers of low molecular weight with narrow polydispersity. Both strong protic acids such as bis(trifluoromethanesulfonyl) amide acid (HTFSA) and a moderately weak acid such as bisoxalato phosphorous acid (HBOP) have been studied as initiators. It has been observed that HTFSA initiates the polymerization rapidly even at room temperature and below, as compared to HBOP which produces a slower polymerization requiring elevated temperatures to complete. The relative difference in reactivity of the initiators as compared to the previously described HBOB initiator is discussed in terms of the difference in their proton acidity and the consequential basicity of the anions. The efficiency of different ILs as the reaction solvent is also presented.

ABA TRIBLOCK COPOLYMERS WITH PENDANT HYDROXYL GROUPS PREPARED BY CONTROLLED CATIONIC POLYMERIZATION AND THEIR USE AS DELIVERY CARRIER FOR PACLITAXEL

To improve the hydrophilicity ofpoly（styrene-b-isobutylene-b-styrene） （SIBS）, this study focuses on the synthesis of novel functional ABA triblock copolymer thermoplastic elastomers （TPEs） with polyisobutylene （PIB） as rubbery segments. The precursor poly{（styrene-co-4-[2-（tert-butyldimethylsiloxy） ethyl]styrene）-b-isobutylene-b-（styrene-co-4-[2- （tert-butyldimethylsiloxy）ethyl]styrene）}（P（St-co-TBDMES）-PIB-P（St-co-TBDMES）） triblock copolymer was first synthesized by living sequential cationic copolymerization of isobutylene （IB） with styrene （St） and 4-[2-（tert- butyldimethylsiloxy）ethyl]styrene （TBDMES） using 1,4-di（2-chloro-2-propyl）benzene （DiCumC1）/titanium tetrachloride （TiCla）/2,6-di-tert-butylpyridine （DtBP） as the initiating system. Then, P（St-co-TBDMES）-PIB-P（St-co-TBDMES） was hydrolyzed in the presence of tetra-butylammonium fluoride to yield poly{[styrene-co-4-（2-hydroxyethyl）styrene]-b- isobutylene-b-[styrene-co-4-（2-hydroxyethyl）styrene]} （P（St-co-HOES）-PIB-P（St-co-HOES）） with pendant hydroxyl groups. P（St-co-HOES）-PIB-P（St-co-HOES） used as the paclitaxel carrier was also investigated in this study. Comparing with SIBS, P（St-co-HOES）-PIB-P（St-co-HOES） has exhibited better compatibility with paclitaxel and higher release rate.

Mechanistic Transformations Involving Radical and Cationic Polymerizations

Mechanistic transformation approach has been widely applied in polymer synthesis due to its unique feature combining structurally different polymers prepared by different polymerization mechanisms.Reported methods for the formation of block and graft copolymers through mechanistic transformation involve almost all polymerizations modes.However,certain polymerization processes require extensive purification processes,which can be time-consuming and problematic.Recent developments on controlled/living polymerizations involving radical and cationic mechanisms with the ability to control molecular weight and functionality led to new pathways for mechanistic transformations.In this mini-review,we systematically discussed relevant advances in the field through three main titles namely(i)from radical to cationic mechanism,(ii)from cationic to radical mechanism,and(iii)application of specific catalyst systems for both radical and cationic polymerizations.

Synthesis and characterization of PEGylated comb-like cationic polymer by polycondensation and ATRP

PEGylated poly（2-（dimethylamino）ethyl methacrylate） with comb-like architecture was synthesized by two-step polymerization. First,poly（oligo（ethylene glycol） malicate）（POEGMA） bearing pendant hydroxyl groups was prepared by direct polycondensation of oligo（ethylene glycol） and malic acid in the presence of scandium triflate as chemoselective catalyst.Then the poly（2- （dimethylamino）ethyl methacrylate） side chains were grafted from the POEGMA backbone by atom transfer radical polymerization （ATRP） after the hydroxyl groups were modified into bromo-ester form,resulting in a PEGylated cationic copolymer with branched architecture.

Phenols/Al(C_(6)F_(5))_(3) Initiation Systems for Cationic Polymerizations of Isobutylene

We report herein the cationic polymerization of isobutylene(IB)under mild conditions is realized with a new binary initiation system generated by simply mixing a Lewis super acid Al(C_(6)F_(5))_(3) and a substituted phenol(RPhOH).Polymers with medium and/or high molecular weights(M_(W)=4.9×10^(4)-27.7×10^(4) g·mol^(-1))can be obtained in toluene and temperatures from-20℃to 0℃.NMR spectrum analysis and DFT sim ulation reveals the in situ generated acidic coordinating complex Ak(C_(6)F_(5))_(3)·RPhOH is the initiating active species,which fu rther tran sformed into the ion-pair[Al(C_(6)F_(5))_(3)ORPh]^(-)[PIB]^(+)of the active intermediates upon growing IB monomers where the counter anion[Al(C_(6)F_(5))_(3)R^(O)Ph]-coordinates to the macrocation via the phenoxy oxygen.The catalyst performances are the concert effects of the steric bulkiness and electronics of the counter anion on the coordinating strength to the macrocation,which is significant to the stability of the active species.

Cationic polymerization of 1,3-pent adiene in the presence of arenes

The cationic polymerizations of 1,3-pentadiene initiated by AlCl3 inn-hexane at 30 degrees C have been carried out in the presence of various arenes, i.e., benzene, toluene, p-xylene, o-xylene, m-xylene and mesitylene. The presence of all these arenes have reduced in different degrees the formation of crosslinked products. Namely, the crosslinking reaction, a major side-reaction during the cationic polymerization of 1,3-pentadiene, has been suppressed by adding the aromatic compounds. The results showed that a chain transfer to arene took place and this transfer process hindered the generation of the crosslinked polymer. IR and H-1 NMR spectra have confirmed the existence of the corresponding aryl groups in the resulting polymers.

Rational design of a cationic polymer network towards record high uptake of ^(99)TcO_(4)^(-)in nuclear waste

^(99)Tc is a long-lived radionuclide present in large amounts as TcO_(4)^(-)-anion in used nuclear fuel.Its removal from the waste stream is highly desirable because of its interference capability with actinide separation and its volatile nature during the nuclear waste vitrification process.Despite the progress achieved in the past few years,the design of anion-exchange materials with optimized Tc uptake property and improved stability under the extreme condition is still a research goal beneficial for reducing the volume of secondary radioactive solid waste generated during the waste partitioning process.However,their design philosophy remains elusive,with challenges coming from charge repulsion,steric hindrance,and insufficient reactive sites within the materials.Herein,we present a design philosophy of cationic polymer network materials for TcO_(4)^(-)separation by systematic precursor screening and structure prediction.This affords an optimized material,SCU-CPN-2(SCU=Soochow University),with extremely high positive charge density while maintaining high radiation resistance.SCU-CPN-2 exhibits a record high adsorption capacity1,467 mg/g towards the surrogate ReO_(4)^(-)compared to all anion-exchange materials reported up to date.In addition to ultrafast adsorption kinetics,SCU-CPN-2 has remarkable selectivity over nitrate and sulfate,and facile recyclability.

Initiating system Me_3SiCl/AlCl_3 for cationic polymerization of 1,3-pentadiene in toluene

Cationic polymerization of 1,3-pentadiene (PD) initiated by trimethylsilyl chloride/aluminium chloride (TMSCl/AlCl3) was carried out in toluene at 30℃.The polymer yield was increased by the addition of TMSC1.However,introduction of TMSC1 gave rise to a drop of the polymer molecular weight.Kinetic results demonstrated that the polymerization initiated by TMSCl/AlCl3 was 2.8 times faster than that induced by AlCl3 alone.Various ethers and ketones were used to mediate the initiating system TMSCl/AlCl3.The polymer yield and molecular weight of the polymer were decreased in the presence of ether.Ketones and ethers had different effects on the polymerization,and the polymer yield and molecular weight were lower than those initiated by AlCl3 alone or TMSCl/AlCl3 Structural evidence revealed that the polymerization was indeed initiated by AlCl3 and HCl rcsulting from hydrolysis of TMSC1 by adventitious water.

Cationic ring-opening polymerization of 3,3-bis(chloromethyl)oxacyclobutane in ionic liquids

Cationic ring-opening polymerization of 3,3-bis（chloromethyl）oxacyclobutane catalyzed by BF3.OEt2 was carded out in ionic liquids [bmim]BF4 and [bmim]PF6. The influences of BCMO concentration and molar ratio of BCMO/BF3.OEt2 on the molecular weights and yield of PBCMO were investigated. The polymerization in ionic liquids proceed to high conversions, although molecular weights are limited, similar to polymerization in organic solvent such as CH2Cl2. Follow a viewpoint of green chemistry, we feel ionic liquid [bmim]BF4 is superior to [bmim]PF6. Extracting [bmim]PF6 from the product using organic solvent as extractant limits its advantage as a green reaction media.

SYNTHESIS AND CATIONIC RING-OPENING POLYMERIZATION OF 1, 4-ANHYDRO-2, 3-DI-O-(P-AZIDOBENZYL)-α-D-RIBOPYRANOSE

New highly stereoregular 2, 3 -di- O-(p-azidobenzyl )-(1 →5 ) - α-D -ribofuranan was synthesized byselective ring-opening polymerization of 1, 4-anhydro-2, 3 - di-O -(p-azidobenzyl )-α-D -ribopyranose(ADABR) using phosphorus pentafluoride or tin tetrachloride as catalyst at low temperature indichloromethane. The monomer was obtained by the reaction of p - bromomethyl -phenyleneazide with 1, 4 -anhydro-α-D-ribose in DMF. The structure of poly(ADANR) was identified by specific rotation and ^(13)C-NMR spectroscopy. Acid chloride-AgCl_4 complex catalyst such as CH_2=C(CH_3)C^+OClO_4^- used in thepolymerization resulted in polymers with mixed structures, i.e. (1→5)-α-D-ribofuranosidic and (1→4)-β-D-ribopyranosidic units. However, with C_6H_5C^+OClO_4^- as catalyst, pure (1→5)-α-D-ribofuranan was obtained.The effects of catalyst, polymerization temperature and time on polymer stereoregularity were examined, andthe mechanism of the ring-opening polymerization was discussed.

Preparation of Cationic Chitosan-Polyacrylamide Flocculant and Its Properties in Wastewater Treatment

Chitosan derived from crab shells, was used to prepare the graft polymer in aqueous solution with acrylamide （AM） and methacrylatoethyl trimethyl ammonium chloride （DMC） as raw materials and ceric ammonium nitrate （CAN） as initiator. The flocculation ability of the resulting polymer （PCAD） was studied in waste water treatment experiments. Its properties were determined on the basis of the transmittance of waste water after flocculation. The effects of ehitosan and DMC content on PCAD＇s flocculation ability were studied. Floeculation experiments were also undertaken under various pH conditions. According to the experimental data, the flocculation ability could be improved when chitosan content decreased in the raw material, but the monomer conversion would decrease obviously. When the ehitosan＇s content was more than 65%, AM and DMC groups were less on each chitosan molecule. So PCAD＇s flocculation ability was poor. Similarly, high content of DMC would result in low monomer conversion and high flocculation ability. PCAD molecules with more DMC group had more positive charges. It was favorable to flocculation. However, monomer conversion would decrease with the increase of DMC content. The suitable conditions were that chitosan and DMC contents were 65% and 15-20%, respectively. The experiment data showed that PCAD had good flocculation ability under weak acidic condition. Its ability would be weakened by strong acidic or alkaline condition. The flocculation efficiency was the best at pH of 5.5 when PCAD＇s dosage was 8mg-Lk Compared with cationic polymer （the copolymer of AM and DMC, PAD）, PCAD showed better flocculation ability under acid and neutral conditions, but worse ability under alkaline condition.