Synergistic anionic/zwitterionic mixed surfactant system with high emulsification efficiency for enhanced oil recovery in low permeability reservoirs

Emulsification is one of the important mechanisms of surfactant flooding. To improve oil recovery for low permeability reservoirs, a highly efficient emulsification oil flooding system consisting of anionic surfactant sodium alkyl glucosyl hydroxypropyl sulfonate(APGSHS) and zwitterionic surfactant octadecyl betaine(BS-18) is proposed. The performance of APGSHS/BS-18 mixed surfactant system was evaluated in terms of interfacial tension, emulsification capability, emulsion size and distribution, wettability alteration, temperature-resistance and salt-resistance. The emulsification speed was used to evaluate the emulsification ability of surfactant systems, and the results show that mixed surfactant systems can completely emulsify the crude oil into emulsions droplets even under low energy conditions. Meanwhile,the system exhibits good temperature and salt resistance. Finally, the best oil recovery of 25.45% is achieved for low permeability core by the mixed surfactant system with a total concentration of 0.3 wt%while the molar ratio of APGSHS:BS-18 is 4:6. The current study indicates that the anionic/zwitterionic mixed surfactant system can improve the oil flooding efficiency and is potential candidate for application in low permeability reservoirs.

Effect of an Anionic Surfactant on Hydraulic Conductivities of Sodium- and Calcium-Saturated Soils

The effect of sodium dodecylbenzenesulfonate (SDBS), an anionic surfactant used widely in household products and industrial processes, on saturated hydraulic conductivities (Ksat) of an Anthrosol saturated with sodium (Na-soil) or calcium (Ca-soil) was analyzed in a laboratory experiment using the constant head method, and adsorption and dispersion experiments were also conducted to infer the possible mechanisms of Ksat fluctuations. The results showed that SDBS was more intensely adsorbed in the Ca-soil than in the Na-soil. With an increase in the SDBS concentration, the stability of the Na-soil suspensions decreased when the SDBS concentration was less than 1.2 mmol L-1 and then above this concentration, increased markedly, while the stability of the Ca-soil suspensions increased gradually at all SDBS concentrations studied. With an increase in the SDBS concentration, the Ksat of the Na-soil increased, which resulted mainly from the increase of water channels in the soil because of the coagulation of the soil particles, while the Ksat of Ca-soil decreased mainly on account of the clogging of partial water channels by precipitated Ca(DBS)2 and the fine soil particles generated.

Synthesis and Characterization of Zirconia Nanocrystallites by Cationic Surfactant and Anionic Surfactant

Study on nanomaterials has attracted great interests in recent years. In this article, zirconia nanocrystallites of different structures have been successfully synthesized via hydrothermal methods with cationic surfactant （CTAB） and anionic surfactant （SDS）, respectively. Differential Scanning Calorimeter （DSC-TG）, X-ray Diffractometer （XRD）, Transmission Electron Microscope （TEM）, Ultraviolet-Visible （UV-vis） and N2 adsorption-desorption analyses are used for their structure characteristics. The results show that the cationic surfactant has a distinctive direction effect on the formation of zirconia nanocrystallites, while the anionic surfactant has a self-assembly synergistic effect on them. The sample synthesized with the cationic surfactant presents good dispersion with the main phase of tetragonal zirconia, and the average nanocrystal size is around 15 nm after calcination at 500 ℃. While the sample synthesized with the anionic surfactant exhibits a worm-like mesoporous structure with pure tetragonal phase after calcination at 500 ℃ and with good thermal stability.

Phase Separation and Microstructure of Mixed Surfactants Solution Containing Cationic Geminis and Traditional Anionic Surfactant

The properties of aqueous two-phase system (ATPS) of mixed solution containing gemini cationic surfactant trimethylene-1,3-bis(dodecyldimethyl ammonium) bromide (12-3-12, 2Br-) and traditional anionic surfactant sodium dodecyl sulfate (SDS) with or without added salt have been studied. An ATPS is formed in a narrow region of the ternary phase diagram different from that of traditional aqueous cationic-anionic surfactant systems. In ATPS region, the lowest total concentration of surfactants varies with the mixing ratio of geminis to SDS. Photographs obtained from freeze-etching, negative-staining and transmission electron microscopy show that the microstructures of two phases are different from each other. Micelles and vesicles can coexist in a single phase. The addition of salts can change the phase diagram of ATPS. Furthermore, the added salts promote the aggregation of rod-like micelles to form coarse network structure that increase the viscosity of solutions. The negative ions of the added salts are the determining factor.

Synthesis of Silica Hollow Spheres with Diameter Around 50 nm by Anionic Surfactant

Silica hollow spheres（SHSs） have attracted great attention because of their low toxicity, low density, large surface area, high chemical and thermal stability, and surface permeability. They can be widely applied in storage^[l], catalysis^[2], drug deli- very^[3,4], low-dielectric-constant materials^[5], low-refractive materials^[6-8], and so on. Up to now, there have been various methods to produce SHSs. Inorganic^[9] or organic particles^[10], such as polystyrene or calcium carbonate, were used as hard templates to create hollow cavities, However, the multistep synthetic process and the lack of structural robustness of the shells upon template removal process weaken their applica- tion. Soft templates, including oil-in-water emulsions^[11,12], vesicles^[13], micelle^[14,15] and gas bubbles^[16], are applied widely.

Improved Ti-containing Mesoporous Silica Catalyst Synthesized by Using Anionic Surfactant as Co-template

Ti-containing mesoporous silica materials(Ti-MSs) with isolated tetrahedrally coordinated Ti species have been widely applied in bulk molecular catalysis. Herein, Ti-MSs were synthesized using anionic surfactant SDS as the co-template. The SDS molecular assembled structures can interact with silica species through the interface hydrogen bonds leading to the formation of mesoporous silica structure with compact Ti-O bonds, lower hydrophilicity and low template cost. The influence of adding SDS as the co-template on the oxidation of styrene with aqueous H_2O_2 as the oxidant was investigated. Ti-MSs using SDS as the co-template showed better catalytic performance as compared with mesoporous titanium silicate synthesized with CTAB serving as the sole template. Moreover, the Ti-MSs synthesized at a Ti/Si ratio of 0.005 demonstrated an optimized performance for styrene oxidation with styrene conversion improved by 14.8%, benzaldehyde selectivity improved by 13.7% and styrene oxide selectivity improved by 9.2% when the reaction time was 6 h.

Theoretical and Experimental Studies on Interactions of Cationic-Anionic Surfactants

Typical cationic and anionic surfactants were chosen and their interactions were calculated by quantum chemical method. Interaction energies are -0.2378 kJ·mol-1, -3.3394kJ·mol-1 and 0.1204kJ·mol-1 for the molecular pairs with fluocarbon and hydrocarbon chain: C4H10/C5H12, C4F10/C5H12, and C4F10 /C5F12, respectively. When hydrophilic group with cationic and anionicions is introduced, interaction energies are -287.40kJ·mol-1, -311.18kJ·mol-1 and -345.83kJ·mol-1. The results show that there is strong static interaction between cationic and anionic surfactants. It has been predicted that mixed monolayer may be formed and surface activity is enhanced favorably, especially for mixtures of cationic and anionic surfactants with fluocarbon and hydrocarbon chains. The anionic surfactants, sodium octadecylbenzenesulfonate perfluopolyetherbenzenesulonate(ANF-I) was synthesized, mixture effects of ANF-I with sodium octadecylbenzenesulfonate or dodecyldimethyl benzylammonium bromide were studied. The results indicate that the efficiency of mixing increased and the theoretical prediction was testified. These results can provide useful information for the design of new surfactants.

Surface Activity Interactions in Aqueous Solution of Anionic Surfactants with a Water Treatment Protein from <i>Moringa oleifera</i>Seeds

The interaction of anionic surfactants sodium dodecylbenzenesulphonate (SDBS) and sodium bis (2-ethyl-1-hexylsulfosuccinate) (AOT) with the water treatment protein extracted from Moringa oleifera seeds has been investigated by surface tension measurements. The results were compared with previously reported studies using surface tension and zeta potential measurements of the same protein with an anionic surfactant sodium dodecylsulphate. There is a strong electrostatic interaction between the protein and the surfactants characterized by a local maximum at intermediate surfactant concentration. This surfactant concentration depends on the protein concentration and corresponds to the surfactant concentration at the point of charge reversal (zeta potential = 0 mV). The number of surfactant molecules required to neutralize the positive charges on the protein was found to be 8 per protein molecule.

Development and Prospect of China’s Anionic Surfactant Industry

The development process of anionic surfactants in China was reviewed.The current status of anionic surfactants in China was analyzed.The overall situation of sulfonation equipment was introduced,and the development trend of anionic surfactant industry in China was prospected.

Anionic Surfactants Levels in M’Koa Lake Water (Jacqueville, Cote d’Ivoire)

In this study, anionic surfactants concentrations and other physico-chemical parameters of surface water quality were assessed in the water of M’Koa Lake in the city of Jacqueville (C?te d’Ivoire). Three sampling campaigns were conducted at different seasons at six (6) sampling stations, identified in M’koa Lake by taking into account potential sources of pollution. The analyses of physico-chemical parameters were carried out using both the French AFNOR standard and the methods described by Rodier. The anionic surfactants concentrations were performed by using the methylene blue colorimetric method. The average concentrations of anionic surfactants in the water of M’koa Lake ranged from 0.23 ± 0.04 mg·L-1 to 1.43 ± 0.68 mg·L-1. They are high compared to both population density and socio-economic activities of Jacqueville’s town. These values can be explained by the characteristics of the studied Lake that do not allow enough dilution of the discharged effluent. The results indicate that M’koa Lake is subjected to harmful pollution by anionic surfactants. And among the physicochemical parameters studied, only turbidity and transparency values show water quality deterioration, favoured by wastewater discharge and direct human activities around the Lake.

Synthesis and Surface Activity of Cashew-Based Anion-Nonionic Surfactants

Four novel anion-nonionic surfactants were synthesized using cashew phenol as raw material. The four structures were characterized by IR and elemental analysis. Their surface activities were investigated. Their critical micelle concentrations (CMC) are 9.30 × 10 –3 mol/L, 8.50 × 10–3 mol/L, 8.10 × 10–3 mol/L and 7.71 ×–3 mol/L respectively, and the corresponding surface tensions at CMC are 28.38 mN/m, 28.60 mN/m, 30.40 mN/m and 30.00 mN/m respectively. The contact angles of the solutions on sheet galsses were measured to observe their surface wettabilities. The effects of their concentrations, the concentrations of NaCl and temperature on their foaming capacity and foam stability were studied.

Overview of Simple Test for Determination of Surfactants by Adhesion Method

A simple, sensitive, and rapid analytical method is reported for the determination of surfactants. This is based on the use of an oppositely charged dye as the ion pair to form an ionic associate with the surfactant in a vessel, thus affording ion-associated adhesion on the inner wall of the vessel. After the adhesion, the remaining solution in the vessel is removed, and the ionic associate is dissolved in a suitable solvent. The absorbance of the resulting solution is measured spectrophotometrically to determine the concentration of the surfactant. Further, the mechanism of adhesion is elucidated.

STUDY ON NEUTRAL DEINKING OF ONP WITH NON-IONIC SURFACTANTS

The ONP neutral deinking performances of fatty alcohol polyoxyethylene ether with different EO value were investigated in this paper. Meanwhile, the synergistic effects of different non-ionic surfactants, the co-operation of non-ionic surfactants with anionic surfactants,and the effects of different salts added into the above two systems on deinkability were also studied. The results showed the deinking performance of A7 was good. But the synergistic effect of A7 and A4 was better. In addition, the accession of salt W2 could improve the deinking efficiency, and the brightness of the deinked pulp was 1.0%ISO higher than that of A7 and A4.

Study on aqueous two-phase systems of the mixture SDS/CTAB surfactants

The phenomenon of two dilute aqueous phases composed of sodium dodecylsulfate(SDS) and cetyl trimethyl ammonium bromide(CTAB) was investigated under various conditions such as concentrations and molar ratios of the two surfactants, the addition of sodium chloride and temperature. Vesicles formation was found in the both phases by TEM image.

Iron Bearing Minerals Flotation from Silica Sand Using Hydroxyl Surfactants

A technological clayey sandstone sample from Wadi Qena locality, Eastern Desert of Egypt, was directed to processing. Fine kaolin and clean silica sand were produced after intensive attrition scrubbing of the sample. To increase the quality of the produced silica, it was subjected to reverse anionic flotation to minimize its iron content. In this respect, conventional flotation tests using three anionic oxyhydryl surfactants namely: sodium dodecyl benzene sulphonate, sodium naphtha sulphonate, and sodium dodecyl sulphate, were tried. Results showed a privilege action for sodium dodecyl sulphate to remove most of the iron oxide content of the sample. A statistical Box-Behnken design was constructed to optimize the process efficiency. It was shown that from a flotation feed contained 360 ppm Fe2O3 and 1190 ppm Al2O3, sand concentrate contained 29 ppm Fe2O3 and 564 ppm Al2O3, was produced. The optimum flotation conditions were 3.86 kg/t sodium dodecyl sulphate dose, 3.22 flotation pulp pH, 1226 rpm impeller speed, and 22.24 L/min airflow rate. Variables interaction effects results showed that flotation separation efficiency was significantly influenced by air flow rate and cell impeller speed of the process.

Evaluation of reusing alum sludge for the coagulation of industrial wastewater containing mixed anionic surfactants

A coagulation-flocculation process is typically employed to treat the industrial wastewater generated by the consumer products industry manufacturing detergents, soaps, and others. The expenditure of chemicals including coagulants and chemicals for pH adjustment is costly for treating this wastewater. The objective of this study was to evaluate the feasibility of reusing the aluminum sulfate （alum） sludge as a coagulant or as a coagulation aid so that the fresh alum dosage can be minimized or the removal efficiency can be enhanced. The experiments were conducted in a jar-test apparatus simulating the coagulation-flocculation process for simultaneous removals of organic matters, anionic surfactants, suspended solids, and turbidity. At the optimum initial pH value of 10 and the fresh alum concentration of 400 mg/L, the total suspended solids （TSS）, total chemical oxygen demand （TCOD）, total anionic surfactants, and turbidity removal efficiencies were 71.5%, 76.4%, 95.4%, and 98.2%, respectively. The addition of alum sludge as a coagulant alone without any fresh alum addition could significantly remove the turbidity, TCOD, and anionic surfactants. The TSS was left in the supernatants after the settling period, but would subsequently be removed by adding the fresh alum. The TSS, TCOD, and turbidity removal efficiencies were also enhanced when both the alum sludge and the fresh alum were employed. The TCOD removal efficiency over 80% has been accomplished, which has never fulfilled by using the fresh alum alone. It is concluded that the alum sludge could be reused for the treatment of industrial wastewater generated by the consumer products industry.

Effect of monovalent anions on cationic Gemini micro-emulsion

Micro-emulsion usually consists of water, oil, surfactants and co-surfactants, and each component has an effect on the phase behavior and solubilization of the micro-emulsion. When the surfactant in the micro-emulsion system is quaternary ammonium cationic Gemini surfactant, the surfactant mainly combines with the anions in the salt. With the increase of salt concentration, the phase transformation of Winsor I → Winsor III → Winsor II occurred, but the optimum salinity and salt width are different because of the type of salt. The effects of 5 different kinds of monovalent anions, including C_6H_5SO_3^-, I-, Br-, NO_3^- and Cl-, on the phase behavior and solubilization of quaternary ammonium cationic Gemini micro-emulsion are researched by Winsor phase diagram. It is found that the effects of organic anions C_6H_5SO_3-and I-on the phase behavior and solubilization of quaternary ammonium cationic Gemini micro-emulsion are most significant, and the effects of Br-, NO_3^- and Cl-are less significant. Meanwhile, when the optimum solubilization is achieved, the amount of sodium benzoate is the least, indicating that the organic anion has stronger self-organization behavior with quaternary ammonium cationic Gemini surfactants.

Effects of common inorganic anions on the rates of photocatalytic degradation of sodium dodecylbenzenesulfonate over illuminated titanium dioxide

Experiments were carried out to study the effects of several anions on the photocatalytic degradation rates of sodium dodecylbenzene sulphonate (DBS) with TiO 2 as catalyst. The anions were added as Na 2SO 4, NaNO 3, NaCl, NaHCO 3, NaH 2PO 4 and Na 3PO 4, and two levels of anion content, i.e. 12 mmol/L and 36 mmol/L in terms of Na +, were studied. The results revealed that: Cl -, SO 2- 4, NO - 3 and HCO - 3 retarded the rates of DBS degradation to different degrees; PO 3- 4 increased the DBS degradation rate at low concentration and decreased the rate at high concentration; H 2PO - 4 accelerated the rate of DBS degradation. The mechanism of the effects of anions on DBS degradation was concluded as the following three aspects: anions compete for the radicals; anions are absorbed on the surface of catalyst and block the active site of catalyst; anions added to the solution change the pH value and influence the formation of ·OH radicals and the adsorption of DBS on catalyst.

Determination of trace inorganic anions in anionic surfactants by single-pump column-switching ion chromatography

An ion chromatography method has been proposed for the determination of three common inorganic anions（chloride,nitrate and sulfate） in anionic surfactants using a single pump system.The new system consists of an ion exclusion column,a concentrator column,and an anion exchange column connected in series via two 6-ports valves in a Dionex ICS-2000 ion chromatograph.The valves were switched several times for removing surfactants,concentrating and separating the three anions.The chromatographic conditions were optimized.Detection limits（S/N = 3） were in the range of 0.10-0.68μg/L.The relative standard deviations（RSDs） of peak area were less than 4.6%.The recoveries were in the range of 84.1-112.6%.

Differences in Adsorption of Anionic Surfactant AOT by Calcium Oxalate： Effect of Crystal Size and Crystalline Phase

The adsorption of anionic surfactant sodium diisooctyl sulfosuccinate（AOT） onto calcium oxalate mono- hydrate（COM） and dihydrate（COD） with sizes of 50, 100 nm, 1, 3 and 10 μm was comparatively studied to simulate the interaction between urinary crystallites and urine components. The adsorption quantity of different concentrations of AOT onto COD and COM with different sizes was detected using a UV-Vis spectrophotometer. The crystalline phase transition of COM and COD before and after adsorption was analyzed by X-ray powder diffraction and Fourier transform infrared spectrometry. The zeta potential of the crystal surface after adsorption of different concentrations of AOT was measured using a zeta potential analyzer. The adsorption quantity of AOT on COM and COD with different sizes was ranked in the following order： 50 nm〉100 nm〉1μm〉3 μm〉10 μm. The adsorption quantity of COM was greater than that of COD with the same size because the density of the positive charges on the COM surface was higher than that on COD surface. With the increase of AOT concentration, the adsorption curves of the large-sized COM and COD（3 and 10μm） were S-type, whereas the adsorption curves of the small-sized COM and COD（50 nm, 100 nm and 1μm） were linear. The adsorption capacities of small-sized COM and COD were much greater than those of the 3 and 10μm crystals. On the basis of the above results, we proposed a molecular model to summarize the absorption of AOT onto COM and COD crystals. Small crystals exhibit a large specific surface area and high surface energy. Thus, the adsorption capacities of them are stronger than those of large crystals. Overall, this study implies that small crystals can easily absorb anionic molecules in urine and may easily adhere to a negatively charged cell surface, thereby increasing the severity of cell injury.