Ordinary Portland Cement (OPC) is by mass the largest manufactured product on Earth, responsible for approximately 6% - 8% of global anthropogenic carbon dioxide emissions (CO<sub>2</sub>) and 35% of indus...Ordinary Portland Cement (OPC) is by mass the largest manufactured product on Earth, responsible for approximately 6% - 8% of global anthropogenic carbon dioxide emissions (CO<sub>2</sub>) and 35% of industrial CO<sub>2</sub> emissions. On average 0.8 to 0.9 ton of CO<sub>2</sub> is emitted to produce one ton of OPC. In this paper, partial substitution of clinker (30% - 35%) by the calcined clay-limestone mixture was investigated in order to produce an eco-cement (LC3). Analyzes by XRF, XRD and ATG/ATD have characterized different components, determined the calcination temperature and selected the right clay which can act as effective Supplementary Cementitious Material (SCM). Mechanical tests on mortar carried out over a period of 90 days. The WBCSD/WRI “Greenhouse Gas Protocol” methodology then allowed the calculation of CO<sub>2</sub> emissions into the atmosphere. Three types of clay are available in the Songololo Region. The kaolinite is the principal clay mineral and its content varies from 27% to 34%. The sum of kaolinite and amorphous phase which enable clay to react with cementitious material ranges from 57% to 60%. The SiO<sub>2</sub> content ranges from 33% to 76%, the Alumina content from 12% to 20% so that the ratio Al<sub>2</sub>O<sub>3</sub>/SiO<sub>2</sub> is on the higher side (0.17 - 0.53). The calcination window is between 750°C and 850°C and the best clay which can act as SCM identified. The clinker’s substitution reduced CO<sub>2</sub> emissions from 0.824 ton of CO<sub>2</sub> for one ton of OPC to 0.640 ton of CO<sub>2</sub> for one ton of LC3, means 22% less emissions. The compressive strengths developed by LC3 vary from 8.91 to 57.6 MPa (Day 1 to Day 90), exceed those of references 32.5 cement and are close to 42.5 cement. In view of the results, LC3 cement can be considered for industrial trials.展开更多
A new type of cement was prepared with ground limestone powder, blastfumace slag, steel slag and gypsum without calcination. The fraction of ground limestone powder in the cement was as high as 40 wt%-60 wt% without P...A new type of cement was prepared with ground limestone powder, blastfumace slag, steel slag and gypsum without calcination. The fraction of ground limestone powder in the cement was as high as 40 wt%-60 wt% without Portland clinker. All of its physical properties can meet the requirements of masonry cement standards. The impact of limestone content on physical properties of the cement and determined its impact on law was investigated. The steel slag can excit the aquation activity of this cement effectively, and the influence of its quantity on the strength of the materials was studied, which shows that the optimum quantity of mixing is 10%. By way of changing the different content of the lime stone by quartzy sample, the law of the compression strength and the PH value was determined, confirming that the lime stone can promote the early aquation of the slag and improve the early strength. The main hydration product of this cement is calcium aluminate hydrate, ettringite and calcium silicate hydrate, as indicated by XRD and SEM analysis.展开更多
Limestone calcined clay cement(LC^3),consisting of ordinary Portland cement(OPC)clinker,calcined clay,limestone powder,and gypsum,has been considered a promising solution to current challenges in the cement and concre...Limestone calcined clay cement(LC^3),consisting of ordinary Portland cement(OPC)clinker,calcined clay,limestone powder,and gypsum,has been considered a promising solution to current challenges in the cement and concrete industry,such as high carbon emissions,high energy consumption,and resource shortages.This study carries out a series of experimental investigations of LC^3-based paste,mortar,and concrete,including microstructural analyses(e.g.hydration product characterization and pore structure analysis)and macro-scale testing(e.g.workability and mechanical properties),using raw materials from south China.The results show that,in LC^3 paste,the replacement of clinker by calcined clay and limestone leads to an increased volume of small pores but decreased total volume of pores.The workability of LC^3 mortar and concrete can be readily tailored using conventional superplasticizers.When designed for comparable 28-d compressive strength,the LC^3 mortar and concrete tend to have lower early-age compressive strength,but comparable compressive strength and higher flexural strength than those of the OPC counterparts at late ages.This study also examines the bond-slip behavior between LC^3 concrete and steel bars and finds that the bond strength is comparable to that of OPC concrete with the same 28-d compressive strength,but that the LC^3 concrete-rebar interface exhibits higher bond-slip stiffness.These findings on LC^3 concrete provide fundamental information and guidance for furthering the application of LC^3 binder in structural concrete in the near future.展开更多
Limestone calcined clay cement(LC3)is an environment-friendly and sustainable cementitious material.It has recently gained considerable attention for the stabilization/solidification(S/S)of soils contaminated by heavy...Limestone calcined clay cement(LC3)is an environment-friendly and sustainable cementitious material.It has recently gained considerable attention for the stabilization/solidification(S/S)of soils contaminated by heavy metals.However,the existing studies on S/S of Zn-contaminated soils using LC3 in terms of hydraulic conductivity and microstructural properties as compared to ordinary Portland cement(OPC)are limited.This study focuses on the evaluation of the mechanical,leaching,and microstructural characteristics of Zn-contaminated soils treated with different contents(0%,4%,6%,8%,and 10%)of low-carbon LC3.The engineering performance of the treated Zn-contaminated soils is assessed over time using unconfined compressive strength(UCS),hydraulic conductivity(k),toxicity characteristic leaching procedure(TCLP),and synthetic precipitation leaching procedure(SPLP)tests.Experimental results show that the UCS of Zn-contaminated soils treated with LC3 ranged from 1.47 to 2.49 MPa,which is higher than 1.63%–13.07%for those treated with OPC.The k of Zn-contaminated soils treated with LC3 ranged from 1.16×10^(−8)to 5.18×10^(−8)cm/s as compared to the OPC treated samples.For the leaching properties,the leached Zn from TCLP and SPLP is 1.58–321.10 mg/L and 0.52–284.65 mg/L as the LC3 contents ranged from 4%to 10%.Further,the corresponding pH modeling results indicate that LC3 promotes a relatively suitable dynamic equilibrium condition to immobilize the higher-level Zn contamination.In addition,microscopic analyses demonstrate that the formations of hydration products,i.e.,Zn(OH)_(2),Zn_(2)SiO_(4),calcium silicate hydrate(C–S–H),calcium silicate aluminate hydrate(C–A–S–H)gel,ettringite,and CaZn(SiO_(4))(H_(2)O),are the primary mechanisms for the immobilization of Zn.This study also provides an empirical formula between the UCS and k to support the application of LC3-solidified Zn-contaminated soils in practical engineering in the field.展开更多
Limestone Calcined Clay Cement(LC^(3)) is a newly proposed low-carbon cement,which can effectively reduce energy consumption and carbon emissions of the traditional cement industry without changing the basic mechanica...Limestone Calcined Clay Cement(LC^(3)) is a newly proposed low-carbon cement,which can effectively reduce energy consumption and carbon emissions of the traditional cement industry without changing the basic mechanical properties of cement-based materials.In this study,the degradation process of mortar samples of limestone and calcined clay cementitious material under sulfate attack is studied by both macroscopic and microscopic analysis.The results show that compared with pure Portland cement,the addition of calcined clay and limestone can significantly reduce the expansion rate,loss of dynamic modulus and mass loss of mortar specimens under sulfate attack.The addition of calcined clay and limestone will refine the pore size distribution of mortar specimens,then inhibiting the diffusion of sulfate and formation of corrosive products,therefore leading to a significant improvement of the sulfate resistance.展开更多
文摘Ordinary Portland Cement (OPC) is by mass the largest manufactured product on Earth, responsible for approximately 6% - 8% of global anthropogenic carbon dioxide emissions (CO<sub>2</sub>) and 35% of industrial CO<sub>2</sub> emissions. On average 0.8 to 0.9 ton of CO<sub>2</sub> is emitted to produce one ton of OPC. In this paper, partial substitution of clinker (30% - 35%) by the calcined clay-limestone mixture was investigated in order to produce an eco-cement (LC3). Analyzes by XRF, XRD and ATG/ATD have characterized different components, determined the calcination temperature and selected the right clay which can act as effective Supplementary Cementitious Material (SCM). Mechanical tests on mortar carried out over a period of 90 days. The WBCSD/WRI “Greenhouse Gas Protocol” methodology then allowed the calculation of CO<sub>2</sub> emissions into the atmosphere. Three types of clay are available in the Songololo Region. The kaolinite is the principal clay mineral and its content varies from 27% to 34%. The sum of kaolinite and amorphous phase which enable clay to react with cementitious material ranges from 57% to 60%. The SiO<sub>2</sub> content ranges from 33% to 76%, the Alumina content from 12% to 20% so that the ratio Al<sub>2</sub>O<sub>3</sub>/SiO<sub>2</sub> is on the higher side (0.17 - 0.53). The calcination window is between 750°C and 850°C and the best clay which can act as SCM identified. The clinker’s substitution reduced CO<sub>2</sub> emissions from 0.824 ton of CO<sub>2</sub> for one ton of OPC to 0.640 ton of CO<sub>2</sub> for one ton of LC3, means 22% less emissions. The compressive strengths developed by LC3 vary from 8.91 to 57.6 MPa (Day 1 to Day 90), exceed those of references 32.5 cement and are close to 42.5 cement. In view of the results, LC3 cement can be considered for industrial trials.
文摘A new type of cement was prepared with ground limestone powder, blastfumace slag, steel slag and gypsum without calcination. The fraction of ground limestone powder in the cement was as high as 40 wt%-60 wt% without Portland clinker. All of its physical properties can meet the requirements of masonry cement standards. The impact of limestone content on physical properties of the cement and determined its impact on law was investigated. The steel slag can excit the aquation activity of this cement effectively, and the influence of its quantity on the strength of the materials was studied, which shows that the optimum quantity of mixing is 10%. By way of changing the different content of the lime stone by quartzy sample, the law of the compression strength and the PH value was determined, confirming that the lime stone can promote the early aquation of the slag and improve the early strength. The main hydration product of this cement is calcium aluminate hydrate, ettringite and calcium silicate hydrate, as indicated by XRD and SEM analysis.
基金the National Natural Science Foundation of China(Nos.51708360 and 51978407)the Shenzhen Basic Research Project of China(No.JCYJ20180305124106675)+4 种基金the Key Projects for International Cooperation in ScienceTechnology and Innovation of China(No.2018YFE0125000)the Taipei University of TechnologyShenzhen University Joint Research Program of China(No.2020008)the National Science Foundation of the USA(No.1661609)the Advanced Materials for Sustainable Infrastructure Seed Funding Program at Missouri University of Science and Technology,USA。
文摘Limestone calcined clay cement(LC^3),consisting of ordinary Portland cement(OPC)clinker,calcined clay,limestone powder,and gypsum,has been considered a promising solution to current challenges in the cement and concrete industry,such as high carbon emissions,high energy consumption,and resource shortages.This study carries out a series of experimental investigations of LC^3-based paste,mortar,and concrete,including microstructural analyses(e.g.hydration product characterization and pore structure analysis)and macro-scale testing(e.g.workability and mechanical properties),using raw materials from south China.The results show that,in LC^3 paste,the replacement of clinker by calcined clay and limestone leads to an increased volume of small pores but decreased total volume of pores.The workability of LC^3 mortar and concrete can be readily tailored using conventional superplasticizers.When designed for comparable 28-d compressive strength,the LC^3 mortar and concrete tend to have lower early-age compressive strength,but comparable compressive strength and higher flexural strength than those of the OPC counterparts at late ages.This study also examines the bond-slip behavior between LC^3 concrete and steel bars and finds that the bond strength is comparable to that of OPC concrete with the same 28-d compressive strength,but that the LC^3 concrete-rebar interface exhibits higher bond-slip stiffness.These findings on LC^3 concrete provide fundamental information and guidance for furthering the application of LC^3 binder in structural concrete in the near future.
基金supported by the Scientific Research Foundation from Sun Yat-sen University and the Guangdong Basic and Applied Basic Research Foundation of China(No.2022A1515110443).
文摘Limestone calcined clay cement(LC3)is an environment-friendly and sustainable cementitious material.It has recently gained considerable attention for the stabilization/solidification(S/S)of soils contaminated by heavy metals.However,the existing studies on S/S of Zn-contaminated soils using LC3 in terms of hydraulic conductivity and microstructural properties as compared to ordinary Portland cement(OPC)are limited.This study focuses on the evaluation of the mechanical,leaching,and microstructural characteristics of Zn-contaminated soils treated with different contents(0%,4%,6%,8%,and 10%)of low-carbon LC3.The engineering performance of the treated Zn-contaminated soils is assessed over time using unconfined compressive strength(UCS),hydraulic conductivity(k),toxicity characteristic leaching procedure(TCLP),and synthetic precipitation leaching procedure(SPLP)tests.Experimental results show that the UCS of Zn-contaminated soils treated with LC3 ranged from 1.47 to 2.49 MPa,which is higher than 1.63%–13.07%for those treated with OPC.The k of Zn-contaminated soils treated with LC3 ranged from 1.16×10^(−8)to 5.18×10^(−8)cm/s as compared to the OPC treated samples.For the leaching properties,the leached Zn from TCLP and SPLP is 1.58–321.10 mg/L and 0.52–284.65 mg/L as the LC3 contents ranged from 4%to 10%.Further,the corresponding pH modeling results indicate that LC3 promotes a relatively suitable dynamic equilibrium condition to immobilize the higher-level Zn contamination.In addition,microscopic analyses demonstrate that the formations of hydration products,i.e.,Zn(OH)_(2),Zn_(2)SiO_(4),calcium silicate hydrate(C–S–H),calcium silicate aluminate hydrate(C–A–S–H)gel,ettringite,and CaZn(SiO_(4))(H_(2)O),are the primary mechanisms for the immobilization of Zn.This study also provides an empirical formula between the UCS and k to support the application of LC3-solidified Zn-contaminated soils in practical engineering in the field.
基金supported in part by grants from National Natural Science Foundation of China(52278259).
文摘Limestone Calcined Clay Cement(LC^(3)) is a newly proposed low-carbon cement,which can effectively reduce energy consumption and carbon emissions of the traditional cement industry without changing the basic mechanical properties of cement-based materials.In this study,the degradation process of mortar samples of limestone and calcined clay cementitious material under sulfate attack is studied by both macroscopic and microscopic analysis.The results show that compared with pure Portland cement,the addition of calcined clay and limestone can significantly reduce the expansion rate,loss of dynamic modulus and mass loss of mortar specimens under sulfate attack.The addition of calcined clay and limestone will refine the pore size distribution of mortar specimens,then inhibiting the diffusion of sulfate and formation of corrosive products,therefore leading to a significant improvement of the sulfate resistance.
