Early Carbonation Behavior of High-volume Dolomite Powder-cement Based Materials

Combined with DTG analysis, X-Ray diffraction analysis （XRD） and field emission scanning electron microscopy analysis （FSEM） affiliated with energy dispersive spectrometer analysis （EDS）, the early hydration and carbonation behavior of cement paste compacts incorporated with 30% of dolomite powder at low water to cement ratio （0.15） was investigated. The results showed that early carbonation curing was capable of developing rapid early strength. It is noted that the carbonation duration should be strictly controlled otherwise subsequent hydration might be hindered. Dolomite powder acted as nuclei of crystallization, resulting in acceleration of products formation and refinement of products crystal size. Therefore, as for cement-based material, it was found that early carbonation could reduce cement dosages to a large extent and promote rapid strength gain resulting from rapid formation of products, supplemental enhancement due to water release in the reaction of carbonation, and formation ofnanometer CaCO3 skeleton network at early age.

The Properties of Road Base Course Materials of Granular Soils Stabilized by AGS Granular Soil Stabilizing Cement

The properties of road base course materials of granular soils stabilized by AGS granular soil stabilizing cement were studied.The AGS cement has an expansibility to a certain degree,so the dry shrinkage of AGS cement paste and AGS stabilized granular is much lower than that of Portland slag cement.AGS has a good suitability to granular soils.Granular soils stabilized by AGS have a much higher strength than that of soils stabilized by P S cement.The same strength can be reached with 20% reduction of cement dosage for AGS cement.And their elastic and resilient modulus are similar,but the former has a much higher tensile splitting strength,so the AGS stabilized granular has a much better anti-cracking performance than that of the P S stabilized granular.The reduced value of the strength and the density with the retard time for the granular soils stabilized by AGS is lower than that for P S cement.

Hydration mechanism of low quality fly ash in cement-based materials

The hydration mechanism of low quality fly ash in cement-based materials was investigated. The hydration heat of the composite cementitious materials was determined by isothermal calorimetry, and the hydration products, quantity, pore structure and morphology were measured by X-ray diffraction(XRD), thermalgravity-differential thermal analysis(TG-DTA), mercury intrusion porosimetry(MIP) and scanning electron microscopy(SEM), respectively. The results indicate that grinding could not only improve the physical properties of the low quality fly ash on particle effect, but also improve hydration properties of the cementitious system from various aspects compared with raw low quality fly ash(RLFA). At the early stage of hydration, the low quanlity fly ash acts as almost inert material; but then at the later stage, high chemical activity, especially for ground low quality fly ash(GLFA), could be observed. It can accelerate the formation of hydration products containing more chemical bonded water, resulting in higher degree of cement hydration, thus denser microstructure and more reasonable pore size distribution, but the hydration heat in total is reduced. It can also delay the induction period, but the accelerating period is shortened and there is little influence on the second exothermic peak.

Effects of Surface-activated Coal Gangue Aggregates on Properties of Cement-based Materials

Effects of calcined coal gangue （CG） aggregates treated by the surface thermal activation on the flowability and strength, and paste-CG aggregate interfaces of the cement-based material were investigated. The experimental results show that the compressive and flexural strength of the cement-based material with the calcined CG aggregates is much higher than that of the material with the natural CG aggregates, but the flowability of the material with calcined CG is significantly reduced with the calcined time. The strength of the material with the calcined CG aggregates only increases little with the calcined time at the same w/c ratio, but is reduced with the calcined time at the same flowability. The CG aggregates calcined by the surface thermal activation obviously overcomes the disadvantages of fully calcined CG.

Self-healing Action of Permeable Crystalline Coating on Pores and Cracks in Cement-based Materials

The self-healing action of a permeable crystalline coating on the po rous mortar was investigated by two times impermeability test. Moreover, the sel f-healing mechanism of cement-based materials with the permeable crystalline c oating was studied by SEM. The results indicate that the permeable crystalline c oating not only seals the pores and cracks in mortar during its curing process, but also heals the permeable pathway caused by first impermeability test or crac ks produced by freeze-thaw cycles. Therefore, cement-based materials can be im proved by the permeable crystalline coating for the self-healing function. SEM images prove that the self-healing function is realized by generating a great q uantity of non-soluble dendritic crystalline within the pores and cracks, which prevents the penetration of water and other liquids.

Effects of the Component and Fiber Gradient Distributions on the Strength of Cement-based Composite Materials

The effects of the component gradient distribution at interface and the fiber gradient distribution on the strength of cement-based materials were studied. The results show that the flexural strength and compressive strength of the mortar and concrete with interface component and fiber gradient distributions are obviously improved. The strengthes of the fiber gradient distributed mortar and concrete (FGDM/C) are higher than those of fiber homogeneously distributed mortar and concrete (FHDM/C). To obtain the same strength, therefore, a smaller fiber volume content in FGDM/C is needed than that in FHDM/C. The results also show that the component gradient distribution of the concrete can be obtained by means of multi-layer vibrating formation.

Effects of Specimen Shape and Size on Water Loss and Drying Shrinkage of Cement-based Materials

The effects of specimen size and shape on development of water loss and shrinkage of mortar and concrete respectively were investigated. The experimental results showed that the effects of specimen size and shape on water loss ratio were consistent with those on drying shrinkage strain. It is also indicated that drying shrinkage strain has obvious linear correlation with water loss ratios independent of specimen size and shape. The effects of specimen size and shape on the water loss ratio were embodied in established model of averaged relative humidity improved by considering effects of sequential hydration and calculated by finite difference method. Furthermore, the effects of specimen size and shape on drying shrinkage strain of concrete were experimentally deduced and applied to modify criterion EB-FIP1990. The comparison between experimental and calculated results shows that the modified EB-FIP1990 can be adopted to predict drying shrinkage strain of concrete with reasonable accuracy.

Influence of Water Content on Conductivity and Piezoresistivity of Cement-based Material with both Carbon Fiber and Carbon Black

The influence of water content on the conductivity and piezoresistivity of cement-based material with carbon fiber （CF） and carbon black （CB） was investigated. The piezoresistivity of cement-based material with both CF and CB was compared with that of cement-based material with CF only, and the changes in electrical resistivity of cement-based material with both CF and CB under static and loading conditions in different drying and soaking time were studied. It is found that the piezoresistivity of cement-based material with both CF and CB has better repeatability and linearity than that of cement-based material with CF only. The conductivity and the sensitivity of piezoresistive cement-based material with both CF and CB are enhanced as the water content in piezoresistive cement-based material increases.

Effects of an AMPS-Modified Polyacrylic Acid Superplasticizer on the Performance of Cement-based Materials

A self-made AMPS-modified polyacrylic acid superplasticizer and two others of the same type but with different molecular structures, which are commercially available, are used in this study to investigate the effect of a 2-acrylamide-2-methyl propylene sulfonic （AMPS）-modified polyacrylic acid superplasticizer on the properties of cement-based materials. In the experiments, initial fluidity, 1 and 2 h fluidity over time after admixtion, bleeding rate of the net cement mortar, and adsorption capacity and rate of cement particles are determined by adding different dosages of the three superplasticizers into the cement paste to characterize the dispersivity and the dispersion retention capability of each superplasticizer. Water-reducing rates of three kinds of mortars are simultaneously determined to characterize the water-reducing capacity of each superplasticizer, as well as the 3 and 28 d compressive strengths to characterize the compression resistance. Results show that water-reducing effect and fluidity better maintain the capability of the AMPS-modified polyacrylic acid superplasticizer than the two commercially available polyacrylic acid superplasticizers, and the compressive strengths after 3 and 28 d show significant growth. In conclusion, the effects of water reduction and strengthening of the AMPS-modified polyacrylic acid superplasticizer are evidently better than those of the two commercially available polyacrylic acid superplasticizers.

Effect of Fly Ash on TSA Resistance of Cement-based Material

Thaumasite form of sulfate attack（TSA）is a major concern in evaluating durability of concrete structures subjected to sulfate and carbonate ions.By means of Fourier transform infrared spectroscopy （FT-IR）,X-ray diffraction（XRD）,scanning electron microscopy（SEM）,and energy dispersive spectrum（EDS） as well as Raman spectra of erosion substances,effect of fly ash on TSA resistance of Portland cement-based material were investigated.Immersed in magnesium sulfate solution with 33 800 ppm mass concentration of SO 4 2-at 5±2℃for 15 weeks,ratio of compressive strength loss decreased as binder replacement ratio of fly ash increased.Furthermore,when binder replacement of fly ash was 60%,compressive strength increased.When thaumasite came into being in samples with 0,15%binder replacement ratio of fly ash,ettringite and gypsum appeared in those with 30%,45%,60%binder replacement ratio of fly ash.Results mentioned above showed that fly ash can restrain formation of thaumasite and improve TSA resistance of Portland cement-based material sufficiently.

Influence of Silica Fume on the Reflectivity and Transmission Efficiency of Cement-Based Materials

As a kind of mineral admixture, silica fume has low permittivity, which will affect the electromagnetic properties of cement-based materials. To study the effect of silica fume on the properties of cement-based materials, the reflectivity, transmission efficiency and pore structure were analyzed by using the vector network analyzer and mercury injection apparatus. Results show that silica fume can make the mortar more compact and the porosity of sample with 9% silica fume is only 17.8%, which is far lower than the control sample;With the increase of the silica fume content, the peak of reflectivity curve increases from -23.2 dB to -16.0 dB, and then decreases from -16.04 dB to -28.7 dB in the frequency range of 6 – 18 GHz. Reflectivity of sample with 3% content of silica fume is lower than other samples within 26.5 - 40 GHz;Transmission efficiency of samples shows the trend of increase with silica fume content increases from 0% to 6% within 8.2 - 12.4 GHz, 12 - 18 GHz and 26.5 - 40 GHz, but when the content increases from 6% to 9%, the transmission efficiency of samples reduces.

Properties of Bamboo Charcoal and Cement-based Composite Materials and Their Microstructure

The objective of this work was to study the properties of bamboo charcoal and cement-based composite materials and their microstructure. The pastes with various bamboo charcoals were prepared and the relative properties such as setting times and strength were tested and the microstructures and pore characteristics of pastes with various bamboos were also studied. The experimental results indicated that bamboo charcoal affects the setting times of cement paste, but the introduction of water reducer relieves this condition. Bamboo charcoal also poses an impact on the hardened paste strength. The prominent strength decrease is found when more and larger size bamboo charcoal is mixed into the cement paste. Bamboo charcoal alters the paste microstructure and increases the porosity and pore volume, but it increases the pores with the diameter of less than 50 μm. The pastes with various bamboo charcoals are given with the good functions such as adjusting humidity and adsorption.

Long-term Durability of Cement-based Materials with Very Low w/b

To investigate the durability, especially the long-term stability of cement-based materials with very low w/b, the air permeability test, carbonation test, capillary absorption rate test and dilation potential test were adopted under long-term heat treatment condition. Microstructure of these materials is also analyzed by scanning electronic microscopy （SEM） and mercury intrusion porosimeter （MIP） in order to further unveil its mechanism and interrelation between microstructure and its properties. The results indicate that in the area investigated, cement-based material with w/b 0.17, like RPC, possesses low porosity and excellent durability. Moreover, its porosity will further decrease under long-term heat treatment compared with normal heat treatment. Its long-term durability is much superior to that of other cement-based materials with w/b 0.25 or 0.35 as high strength concrete（HSC）.

Analytical Methods for Prediction of Water Absorption in Cement-Based Material

The capillary absorption of water by unsaturated cement-based material is the main reason of degradation of the structures subjected to an aggressive environment since water often acts as the transporting medium for damaging contaminants. It is well known that the capillarity coefficient and sorptivity are two important parameters to characterize the water absorption of porous materials. Generally, the former is used to describe the penetration depth or height of water transport, which must be measured by special and advanced equipment. In contrast, the sorptivity represents the relationship between cumulative volume of water uptake and the squareroot of the elapsed time, which can be easily measured by the gravimetric method in a normal laboratory condition. In the present study, an analytical method is developed to build up a bridge between these two parameters, with the purpose that the sorptivity or the gravimetric method can be used to predict the penetration depth of water absorption. Additionally, a new model to explain the dependence of sorptivity on initial water content of the material is developed in order to fit the in situ condition. The comparison of predicted results by the analytical method with experimental data or numerical calculation results, as well as some previous models, validates the feasibility of the methods presented in this paper.

Multi-scale Modeling of the Effective Chloride Ion Diffusion Coefficient in Cement-based Composite Materials

N-layered spherical inclusions model was used to calculate the effective diffusion coefficient of chloride ion in cement-based materials by using multi-scale method and then to investigate the relationship between the diffusivity and the microstructure of cement-basted materials where the microstructure included the interfacial transition zone （ITZ） between the aggregates and the bulk cement pastes as well as the microstructure of the bulk cement paste itself. For the convenience of applications, the mortar and concrete were considered as a four-phase spherical model, consisting of cement continuous phase, dispersed aggregates phase, interface transition zone and their homogenized effective medium phase. A general effective medium equation was established to calculate the diffusion coefficient of the hardened cement paste by considering the microstructure. During calculation, the tortuosity （n） and constrictivity factors （Ds/Do） of pore in the hardened pastes are n^3.2, Ds/Do=l.Ox 10-4 respectively from the test data. The calculated results using the n-layered spherical inclusions model are in good agreement with the experimental results; The effective diffusion coefficient of ITZ is 12 times that of the bulk cement for mortar and 17 times for concrete due to the difference between particle size distribution and the volume fraction of aggregates in mortar and concrete.

Form and Mechanism of Sulfate Attack on Cement-based Material Made of Limestone Powder at Low Water-binder Ratio under Low Temperature Conditions

The development of strength and the form of attack of cement-based material made of limestone powder at low water-binder ratio under low-temperature sulfate environment were studied. The results indicate that when water-binder ratio is lower than 0.40, the cement-based material with limestone powder has insignificant change in appearance after being soaked in 10% magnesium sulfate solution at low temperature for 120 d, and has significant change in appearance after being soaked at the age of 200 d. Expansion damage and exfoliation occur on the surface of concrete test cube at different levels. When limestone powder accounts for about 28 percent of cementitious material, with the decrease of water-binder ratio, the compressive strength loss has gradually decreased after the material is soaked in the magnesium sulfate solution at low temperature at the age of 200 d. After the specimen with the water-binder ratio of less than 0.4 and the limestone powder volume of greater than 20% is soaked in 10% magnesium sulfate solution at low temperature at the age of 200 d, gypsum attack-led destruction is caused to the concrete test cube, without thaumasite sulfate attack.

Application of Air-cooled Blast Furnace Slag Aggregates as Replacement of Natural Aggregates in Cement-based Materials：A Study on Water Absorption Property

The influence of air-cooled blast furnace slag aggregates as replacement of natural aggregates on the water absorption of concrete and mortar was studied, and the mechanism was analyzed. The interface between aggregate and matrix in concrete was analyzed by using a micro-hardness tester, a laser confocal microscope and a scanning electron microscope with backscattered electron image mode. The pore structure of mortar matrixes under different curing conditions was investigated by mercury intrusion porosimetry. The results showed that when natural aggregates were replaced with air-cooled blast furnace slag aggregates in mortar or concrete, the content of the capillary pore in the mortar matrix was reduced and the interfacial structure between aggregate and matrix was improved, resulting in the lower water absorption of mortar or concrete. Compared to the concrete made with crushed limestone and natural river sand, the initial absorption coefficient, the secondary absorption coefficient and the water absorption capacity through the surface for 7 d of the concrete made from crushed air-cooled blast furnace slag and air-cooled blast furnace slag sand were reduced by 48.9%, 52.8%, and 46.5%, respectively.

Time Dependent Surface Heat Transfer in Light Weight Aggregate Cement Based Materials

Surface temperature changes of building materials affect the calculation of heat flow and thus the energy use in heating and cooling. The surface heat transfer coefficient , limiting the heat flow between material surface and ambient air is normally taken as a constant. In this study we propose a time-dependent function . We estimate from unidirectional heat flow experiments with transient and steady-state conditions. Using temperature measurements and the conservation of energy at the surface including convective and irradiative boundary conditions, the value of was obtained both using Finite Difference and Taylor Polynomials methods. Numerical solutions of temperature distribution as function of time were improved with the obtained -functions compared to with constant . There were no clear difference between on different materials, and the final values observed were in the order of magnitude expected from the literature.

Attack of Limestone Cement-based Material Exposed to Magnesium Sulfate Solution at Low Temperature

Limestone in cement could be a source of CO3^2- needed for thaumasite formation which will result in thanmasite form of sulfate attack （TSA） probably. TSA has more deterioration than ettringite or gypsum form of sulfate attack because it targets the calcium silicate hydrates （C-S-H） which is the main binder phase in all Portland cement-based materials. By means of physical and mechanical property testing as well as erosion phases analysis, magnesium sulfate attack of cement-based material containing 35% limestone powder by mass at 5 ± 2 ℃ is investigated. The compressive strength and flexural strength of mortar specimen immersed in MgSO4 solution increase firstly, then decrease rapidly with the immersing age. Relative dynamic elastic modulus of mortar specimen changes in a phased process. After immersing in MgSO4 solution for 15 weeks, the main erosion phases in paste specimen change from four phases compounds, three phases compounds to two phases compounds from surface to inside. Deterioration course of limestone cement-based material exposed to magnesium sulfate aggressive environment appears progressive damage layer by layer, and every layer probably suffers four stages, which are property strengthening stage, initial degradation stage, thaumasite formation stage and cementation loss stage, respectively.

Hydration Process of Cement-Based Materials by AC Impedance Method

AC impedance is a new method to study the changes of pore structure and the hydration degree during the hydration and hardening process of cement paste by the change of the electrochemical parameters. Employing AC impedance method, we studied the hydration and hardening process of cement paste with fly ash and slag, and analyzed the influence of different hydration age, water-binder ratio and mineral admixture on the impedance parameters. Moreover, we compared the results with those by the conventional porosity testing method and X-ray diffraction method. The results showed that AC impedance could be taken as a new technology in cement and concrete research.