F mineral admixture (FMA) is made of the fin- ely divided powder of natural zeolite with a bit of other agent. When FMA is used to displace about 10% (by weight) of the ordinary portland cement (OPC) (strength grade 5...F mineral admixture (FMA) is made of the fin- ely divided powder of natural zeolite with a bit of other agent. When FMA is used to displace about 10% (by weight) of the ordinary portland cement (OPC) (strength grade 575#) in concrete and mixed with a suitable amount of super plasticizer (w/c =0.31-0.35), then a high-strength concrete with compressive strength about 80 MPa and slump about 180 MM can be obtained. The strength of this concrete is about 10-15% higher than that of the corresponding concrete mixing with pure OPC, and its bleeding decreases greatly. It makes no segre- gation and separation, and thus it satisfies the requirement of pumping concrete in construction.展开更多
This experimental study aims to examine the influence of many crucial parameters on the workability and compressive strength of Ready-Mix Concrete (RMC). The study utilized two distinct varieties of superplasticizers ...This experimental study aims to examine the influence of many crucial parameters on the workability and compressive strength of Ready-Mix Concrete (RMC). The study utilized two distinct varieties of superplasticizers obtained from the local market. The fine aggregates utilized in this study were sourced from Sylhet sand, whereas the coarse aggregates were comprised of boulder crushed stone chips. The experimental procedures adhered to the requirements outlined by ASTM. A comprehensive investigation was conducted on a range of concrete compositions that used diverse chemical admixtures. The slump test was performed at regular intervals of 15 minutes until the slump value reached or fell below 3 cm after the mixing of the concrete. In the scenario involving two-stage admixture dosage, the second stage of admixture was introduced once the slump reached or dropped below 3 cm, following which the casting process was initiated. The process of curing concrete specimens consists of two distinct stages: the main stage and the final stage. Cylindrical specimens, with a diameter of 4 inches and a height of 8 inches, were manufactured for the purpose of evaluating their compressive strength at both 7 and 28 days. During the experimental trials, the water-cement (w/c) ratio was kept consistent, while different dosages of admixture were applied. The findings of the study indicate that the utilization of a two-stage dose of admixture resulted in enhanced and extended workability, along with higher strength of the concrete in comparison to specimens that did not incorporate any admixture. This research study enhances the comprehension of optimizing qualities of ready-mix concrete (RMC) by varying the superplasticizer, providing useful insights for the building sector.展开更多
文摘F mineral admixture (FMA) is made of the fin- ely divided powder of natural zeolite with a bit of other agent. When FMA is used to displace about 10% (by weight) of the ordinary portland cement (OPC) (strength grade 575#) in concrete and mixed with a suitable amount of super plasticizer (w/c =0.31-0.35), then a high-strength concrete with compressive strength about 80 MPa and slump about 180 MM can be obtained. The strength of this concrete is about 10-15% higher than that of the corresponding concrete mixing with pure OPC, and its bleeding decreases greatly. It makes no segre- gation and separation, and thus it satisfies the requirement of pumping concrete in construction.
文摘This experimental study aims to examine the influence of many crucial parameters on the workability and compressive strength of Ready-Mix Concrete (RMC). The study utilized two distinct varieties of superplasticizers obtained from the local market. The fine aggregates utilized in this study were sourced from Sylhet sand, whereas the coarse aggregates were comprised of boulder crushed stone chips. The experimental procedures adhered to the requirements outlined by ASTM. A comprehensive investigation was conducted on a range of concrete compositions that used diverse chemical admixtures. The slump test was performed at regular intervals of 15 minutes until the slump value reached or fell below 3 cm after the mixing of the concrete. In the scenario involving two-stage admixture dosage, the second stage of admixture was introduced once the slump reached or dropped below 3 cm, following which the casting process was initiated. The process of curing concrete specimens consists of two distinct stages: the main stage and the final stage. Cylindrical specimens, with a diameter of 4 inches and a height of 8 inches, were manufactured for the purpose of evaluating their compressive strength at both 7 and 28 days. During the experimental trials, the water-cement (w/c) ratio was kept consistent, while different dosages of admixture were applied. The findings of the study indicate that the utilization of a two-stage dose of admixture resulted in enhanced and extended workability, along with higher strength of the concrete in comparison to specimens that did not incorporate any admixture. This research study enhances the comprehension of optimizing qualities of ready-mix concrete (RMC) by varying the superplasticizer, providing useful insights for the building sector.