Reliability assessment for serviceability limit states of stiffened deep cement mixing column-supported embankments

The reliability and deterministic analyses of wood-cored stiffened deep cement mixing and deep cement mixing column-supported embankments(referred to as WSCSE and DCSE,respectively)considering serviceability limit state requirements are presented in this paper.Random field theory was used to simulate the spatial variability of soil
cement mixing(SCM)material in which the adaptive Kriging Monte Carlo simulation was adopted to estimate the failure probability of a column
supported embankment(CSE)system.A new method for stochastically generating random values of unconfined compressive strength(qu)and the ratio(Ru)between the undrained elastic modulus and qu of SCM material based on statistical correlation data is proposed.Reliability performance of CSEs concerning changes in the mean(μ),coefficient of variation(CoV),and vertical spatial correlation length(θv)of qu and Ru are presented and discussed.The obtained results indicate that WSCSE can provide a significantly higher reliability level and can tolerate more SCM material spatial variability than DCSE.Some performance of DCSE and WSCSE,which can be considered satisfactory in a deterministic framework,cannot guarantee an acceptable reliability level from a probabilistic viewpoint.This highlights the importance and necessity of employing reliability analyses for the design of CSEs.Moreover,consideration of only μ and CoV of qu seems to be sufficient for reliability analysis of WSCSE while for DCSE,uncertainties regarding the Ru(i.e.both μ and CoV)and θv of qu cannot be ignored.

Engineering behaviour of in situ cored deep cement mixed marine deposits subjected to undrained and drained shearing

The deep cement mixing(DCM)is used to improve the capacity and reduce the settlement of the soft ground by forming cemented clay columns.The investigation on the mechanical behaviour of the DCM samples is limited to either laboratory-prepared samples or in-situ samples under unconfined compression.In this study,a series of drained and undrained triaxial shearing tests was performed on the in-situ cored DCM samples with high cement content to assess their mechanical behaviours.It is found that the drainage condition affects significantly the stiffness,peak and residual strengths of the DCM samples,which is mainly due to the state of excess pore water pressure at different strain levels,i.e.being positive before the peak deviatoric stress and negative after the peak deviatoric stress,in the undrained tests.The slope of the failure envelope changes obviously with the confining pressures,being steeper at lower stress levels and flatter at higher stress levels.The strength parameters,effective cohesion and friction angle obtained from lower stress levels(c′0 andφ′0)are 400 kPa and 58°,respectively,which are deemed to be true for design in most DCM applications where the in-situ stress levels are normally at lower values of 50-200 kPa.Additionally,the computed tomography(CT)scanning system was adopted to visualize the internal structures of DCM samples.It is found that the clay pockets existing inside the DCM samples due to uneven mixing affect markedly their stress-strain behaviour,which is one of the main reasons for the high variability of the DCM samples.

Field testing of stiffened deep cement mixing piles under lateral cyclic loading

Construction of seaside and underground wall bracing often uses stiffened deep cement mixed columns （SDCM）. This research investigates methods used to improve the level of bearing capacity of these SDCM when subjected to cyclic lateral loading via various types of stiffer cores. Eight piles, two deep cement mixed piles and six stiffened deep cement mixing piles with three different types of cores, H shape cross section prestressed concrete, steel pipe, and H-beam steel, were embedded though soft clay into medium-hard clay on site in Thailand. Cyclic horizontal loading was gradually applied until pile failure and the hysteresis loops of lateral load vs. lateral deformation were recorded. The lateral carrying capacities of the SDCM piles with an H-beam steel core increased by 3-4 times that of the DCM piles. This field research clearly shows that using H-beam steel as a stiffer core for SDCM piles is the best method to improve its lateral carrying capacity, ductility and energy dissipation capacity.

Deformation and stability of the seawall,considering the strength uncertainty of cement mixing piles

The cement mixing (CM) pile is a common method of improving soft offshore ground. The strength growth of CM piles under complex conditions is affected by many factors, especially the cement and moisture contents, and shows significant uncertainty. To investigate the stochasticity of the early strength of CM piles and its impact on the displacement and stability of a seawall, a series of laboratory tests and numerical analyses were carried out in this study. Vane shear tests were conducted on the cement-solidified soil to determine the relationships between the undrained shear strength s_(u) of the cement soil curing in the seawater and the cement content a_(c), as well as the in situ soil moisture content w. It can be inferred that the 24 h undrained shear strength follows a normal distribution. A numerical model considering the random CM pile strength was established to investigate the deformation of the seawall. Due to the uncertainty of CM pile strength, the displacement of the seawall demonstrates a certain discreteness. The decrease of the mean undrained shear strength of CM piles causes a corresponding increase in the average displacement of the seawall. When the mean strength of CM piles is lower than a certain threshold, there is a risk of instability. Furthermore, the heterogeneity of the strength within an individual CM pile also has an impact on seawall displacement. Attention should be paid to the uncertainty of CM pile strength to control displacement and stability.

Consolidation behavior of cement—and lime／cement—mixed column foundations

The consolidation behavior of mixed in place cement and lime/cement mixed column was studied. Consolidation of the composite foundation was modeled as a three dimensional axi symmetric problem. The authors used the finite difference method to obtain the pore pressure variation with time at any location below the surface. A computer program developed by the authors was used to draw some interesting conclusions about the consolidation behaviors of cement and lime/cement mixed pile foundation. Finally, a combined model including the permeability coefficients of cement mixed piles and soil, was studied and its feasibility was evaluated.

Bearing Behaviors of Stiffened Deep Cement Mixed Pile

A series of investigations were conducted to study the bearing capacity and load transfer mechanism of stiffened deep cement mixed （SDCM） pile. Laboratory tests including six specimens were conducted to investigate the frictional resistance between the concrete core and the cementsoil. Two model piles and twenty-four full-scale piles were tested to examine the bearing behavior of single pile. Laboratory and model tests results indicate that the cohesive strength is large enough to ensure the interaction between core pile and the outer cement-soil. The full-scale test results show that the SDCM piles exhibit similar bearing behavior to bored and cast-in-place concrete piles. In general, with the rational composite structure the SDCM piles can transmit the applied load effectively, and due to the addition of the stiffer core, the SDCM piles possess high bearing capacity. Based on the findings of these experimental investigations and theoretical analysi , a practical design method is developed to predict the vertical bearing capacity of SDCM pile.

Cement Treated Recycled Demolition Waste as a Road Base Material

To enhance the performance of mix granulate road base courses by cement treatment. The mechanical properties of cement treated mix granulate （CTMG） were studied, which was designed with 65% crushed masonry and 35% crushed concrete by mass. The central composite design was employed to prepare specimens with different levels of cement content and degree of compaction. All specimens were cured in a fog room at 20 ℃ for a specific number of days. The compressive strength and the indirect tensile strength were determined through the monotonic compression and indirect tension tests. Effective prediction models for the mechanical properties of CTMG, in relation to the cement content, the degree of compaction and the curing time, were successfully established for a mix containing 65% crushed masonry and 35% crushed concrete by mass.

Reliability-based settlement analysis of embankments over soft soils reinforced with T-shaped deep cement mixing piles

This paper presents a reliability-based settlement analysis of T-shaped deep cement mixing(TDM)pile-supported embankments over soft soils.The uncertainties of the mechanical properties of the in-situ soil,pile,and embankment,and the effect of the pile shape are considered simultaneously.The analyses are performed using Monte Carlo Simulations in combination with an adaptive Kriging(using adaptive sampling algorithm).Individual and system failure probabilities,in terms of the differential and maximum settlements(serviceability limit state(SLS)requirements),are considered.The reliability results for the embankments supported by TDM piles,with various shapes,are compared and discussed together with the results for conventional deep cement mixing pile-supported embankments with equivalent pile volumes.The influences of the inherent variabilities in the material properties(mean and coefficient of variation values)on the reliability of the piled embankments,are also investigated.This study shows that large TDM piles,particularly those with a shape factor of greater than 3,can enhance the reliability of the embankment in terms of SLS requirements,and even avoid unacceptable reliability levels caused by variability in the material properties.

Experimental study on geosynthetic-reinforced sand fill over marine clay with or without deep cement mixed soil columns under different loadings

Geosynthetics and deep cement mixed(DCM)soil columns have been widely used to improve soft soil grounds in many countries and regions.This paper presents an experimental study on a geosynthetic-reinforced sand fill over marine clay with or without DCM columns under different loadings.Two tests were conducted on the sand fill reinforced with fixed-end and free-end geosynthetics over marine clay under three-stage local loading to investigate the effects of the boundary conditions of geosynthetic reinforcement on reducing settlements.It is observed that the fixed-end geosynthetic sheet is more effective in reducing settlements than the free-end condition under identical local loading.Another test was conducted on the fixed-end geosynthetic-reinforced sand fill over the marine clay improved by DCM columns under single-stage uniform loading.The vertical stresses on the marine clay and on the DCM columns,as well as the tensile strains of the geosynthetic sheet in the overlying sand fill,were measured.The results revealed that the stress concentration ratio increases with an increase in consolidation settlements,and the maximum tensile strain of the geosynthetic sheet occurs near the edge rather than at the center of the top surface of the DCM columns.

A method for predicting consolidation settlements of floating column improved clayey subsoil

A method of predicting the consolidation settlement-time curve of floating soil-cement column on improved soft clayey subsoil has been proposed.The degree of the consolidation(U(t))of the system is calculated by the double soil-layer consolidation theory,and the methods for evaluating the equivalent hydraulic conductivity(k)and the coefficient of volume compressibility(mv)of the part of the column improved layer have been proposed.The effectiveness of the method was verified by comparing predictions with the results of finite element analysis(FEA)using a unit cell model.The consolidation settlement(s(t))can be calculated by the method of treating a part of the column improved layer as an unimproved layer and using the corresponding average U(t)value.By comparing the predicted results with the measurements of laboratory model tests and three case histories in Fukuoka,Japan,the effectiveness of the proposed methods has been verified.It is suggested that the method can be used for designing the soft clayey subsoil improvement using floating soil-cement columns.