Effects of Cationic Surfactant on Fresh and Hardened Properties of Cement-Based Mortar

The objective of this study is to analyze the effects of using surfactant(CTAB)and cellulose nanofibers(NFC)as an admixture in cement mortars.We examined composite properties as porosity,compression energy,thermal conductivity and hydration.The results showed that with the addition of 0.7%by weight of NFC per emulsion in the presence of a cationic surfactant(CTAB).The new material produced presented a dry porosity between 4.7%and 4.4%,compressive strength between 9.8 and 22.9 MPa,and thermal conductivity between 0.95 and 2.25 W·m^(−1)·K^(−1).Thus we show better mechanical and thermal performance than that traditional Portland cement mortar with a density similar.In addition,the mortar made by emulsion of ordinary portland cement,cellulose nanofiber and organophilic clay(OC)treated with cetyltrimethylammonium bromide(CTAB)obtained has good resistance under high temperature and water,as well as excellent thermal insulation performance under high temperature and humidity conditions.This study verified that the presence of NFC promotes hydration,leading to the production of more calcium silicate and portlandite gel.

Reinforcing effects of polypropylene on energy absorption and fracturing of cement-based tailings backfill under impact loading

Polypropylene(PP)fiber-reinforced cement-based tailings backfill(FRCTB)is a green compound material with superior crack resistance and has good prospects for application in underground mining.However,FRCTB exhibits susceptibility to dynamic events,such as impact ground pressure and blast vibrations.This paper investigates the energy and crack distribution behavior of FRCTB under dynamic impact,considering the height/diameter(H/D)effect.Split Hopkinson pressure bar,industrial computed tomography scan,and scanning electron microscopy(SEM)experiments were carried out on six types of FRCTB.Laboratory outcomes confirmed fiber aggregation at the bottom of specimens.When H/D was less than 0.8,the proportion of PP fibers distributed along theθangle direction of80°-90°increased.For the total energy,all samples presented similar energy absorption,reflectance,and transmittance.However,a rise in H/D may cause a rise in the energy absorption rate of FRCTB during the peak phase.A positive correlation existed between the average strain rate and absorbed energy per unit volume.The increase in H/D resulted in a decreased crack volume fraction of FRCTB.When the H/D was greater than or equal to 0.7,the maximum crack volume fraction of FRCTB was observed close to the incidence plane.Radial cracks were present only in the FRCTB with an H/D ratio of 0.5.Samples with H/D ratios of 0.5 and 0.6 showed similar distributions of weakly and heavily damaged areas.PP fibers can limit the emergence and expansion of cracks by influencing their path.SEM observations revealed considerable differences in the bonding strengths between fibers and the FRCTB.Fibers that adhered particularly well to the substrate were attracted together with the hydration products adhering to surfaces.These results show that FRCTB is promising as a sustainable and green backfill for determining the design properties of mining with backfill.

The Influence of Carbon Nanotubes and Nano-Silica Fume on Enhancing the Damping and Mechanical Properties of Cement-Based Materials

This paper conducted experimental studies on the damping and mechanical properties of carbon nanotube-nanosilica-cement composite materials with different carbon nanotube contents. The damping and mechanical properties enhancement mechanisms were analyzed and compared through the porosity structure test, XRD analysis, and scanning electron microscope observation. The results show that the introduction of nanosilica significantly improves the dispersion of carbon nanotubes in the cement matrix. At the same time, the addition of nanosilica not only effectively reduces the critical pore size and average pore size of the cement composite material, but also exhibits good synergistic effects with carbon nanotubes, which can significantly optimize the pore structure. Finally, a rationalization suggestion for the co-doping of nanosilica and carbon nanotubes was given to achieve a significant increase in the flexural strength, compressive strength and loss factor of cement-based materials.

Effect of Glutinous Rice Flour on Mechanical Properties and Microstructure of Cement-based Materials

The mechanism of glutinous rice flour,a kind of natural admixture,on the hydration process,setting time,and microstructure of the Portland cement was investigated.The experimental results show that the glutinous rice flour has an obvious setting retarding effect on cement pastes.The optimal dosage of the glutinous rice flour is 3wt%.In this case,the initial and final setting time of the paste are delayed by 140 and185 min,respectively.The flexural and compressive strengths of the hardened paste are increased by 0.35%and 0.07%after 56 d of curing.The glutinous rice flour hinders the mineral dissolution process and decreases the concentration of calcium ion at the initial stage of hydration due to the complexation effect,thereby hindering the nucleation and growth of CH and C-S-H phases and prolonging the hydration process.However,C-S-H phases combine with the glutinous rice flour to contribute the bonding effect together,which compacts the microstructure of hardened cement pastes at the later hydration stage of cement pastes.Thus,in-depth investigation on the utilization of glutinous rice flour as the admixture for the Portland cement is expected to be meaningful for the control of hydration exothermic rate and setting time.

Copper Ions Removal from Wastewater by Electrocoagulation Using Cement-based Cathode Plates

The present work uses PEO solution to well disperse carbon fiber and identifies percolation thresholds of carbon fiber and carbon black which are used as conductive fillers.The resultant cathode plates have an average compressive strength of 27.3 MPa and flexural strength of 29.09 MPa,which demonstrate excellent mechanical properties.The Cu^(2+)removal efficiency was measured at different current densities in EC process with cement-based cathode plate,while the voltage changes were recorded.The results showed that the cement-based cathode plate operated stably and achieved 99.7%removal of 1 L of simulated wastewater with a Cu^(2+)concentration of 200 ppm at a current density of 8 m A/cm^(2)for 1 h.Characterization of floc and tested cathode plates,SEM and EDS analyses,and repeatability testing of the tested plates demonstrate the reusability of the plates,proving that cement-based plates can effectively replace metal cathode plates,reduce the cost of EC and improve the applicability of EC devices.

Experimental and Numerical Research on Water Transport during Adsorption and Desorption in Cement-Based Materials

The durability of cement-based materials is related to water transport and storage in their pore network under different humidity conditions.To understand the mechanism and characteristics of water adsorption and desorption processes from the microscopic scale,this study introduces different points of view for the pore space model generation and numerical simulation of water transport by considering the“ink-bottle”effect.On the basis of the pore structure parameters(i.e.,pore size distribution and porosity)of cement paste and mortar with water-binder ratios of 0.3,0.4 and 0.5 obtained via mercury intrusion porosimetry,randomly formed 3D pore space models are generated using two-phase transformation on Gaussian random fields and verified via image analysis method of mathematical morphology.Considering the Kelvin-Laplace equation and the influence of“ink-bottle”pores,two numerical calculation scenarios based on mathematical morphology are proposed and applied to the generated model to simulate the adsorption-desorption process.The simulated adsorption and desorption curves are close to those of the experiment,verifying the effectiveness of the developed model and methods.The obtained results characterize water transport in cement-based materials during the variation of relative humidity and further explain the hysteresis effect due to“ink-bottle”pores from the microscopic scale.

Effects of Strain Rate and Fiber Content on the Dynamic Mechanical Properties of Sisal Fiber Cement-Based Composites

In this paper,a split Hopkinson pressure bar(SHPB)was used to investigate the dynamic impact mechanical behavior of sisal fiber-reinforced cement-based composites(SFRCCs),and the microscopic damage evolution of the composites was analyzed by scanning electron microscopy(SEM)and energy-dispersive X-ray spectrome-try(EDS).The results show that the addition of sisal fibers improves the impact resistance of cement-based composite materials.Compared with ordinary cement-based composites(OCCs),the SFRCCs demonstrate higher post-peak strength,ductility,and energy absorption capacity with higher fiber content.Moreover,the SFRCCs are strain rate sensitive materials,and their peak stress,ultimate strain,and energy integrals all increase with increasing strain rate.From the perspective of fracture failure characteristics,the failure of OCCs is dominated by the brittle failure of crystal cleavage.In contrast,the failure mode of the SFRCCs changes to microscale matrix cracks,multi-scale pull-out interface debonding of fibers(fine filaments and bundles),and mechanical interlock.This research provides an experimental basis for the engineering application of high-performance and green cement-based composites.

Evolution of Biofilm and Its Effect on Microstructure of Mortar Surfaces in Simulated Seawater

To explore the role of biofilm formation on the corrosion of marine concrete structures, we investigated the attachment of biofilm on mortar surfaces in simulated seawater and the influence of biofilm on the microstructure of mortar surfaces. The results show that the evolution of biofilm on mortar surfaces in simulated seawater is closely related to the corrosion suffered by the mortar, and the process of biofilm attachment and shedding is continuous and cyclical. It is found that the specimens in the absence of biofilm attachment are more severely eroded internally by the corrosive medium in simulated seawater than those in the presence of biofilm attachment. For the specimens without biofilm attachment, after 60 days, gypsum forms,and after 120 days, the number of pores in the mortar is reduced. In contrast, for the specimens in the presence of biofilm attachment, gypsum could only be detected after 90 days, and fewer pores are filled. Therefore, the formation of biofilm could delay the invasion of the corrosive medium into the interior of mortar during the evolution of biofilm on mortar surfaces, mitigating the corrosion of mortars in seawater.

Red Cement-based Decorative Mortar Prepared with Dry Electroplating Sludge Containing Pb as Red Pigment

Red cement-based decorative mortars were prepared with different content electroplating sludge containing Pb （EPSP）, and their colors, water absorption, strengths, hydration characteristics and heavy metal leachabilities were investigated. The experimental results show that EPSP can adjust the mortar color well as the red pigments exclusively used in the decorative mortarS. EPSP will result in the increase of water absorption, but the mortar produced with 5% EPSP still has the very satisfactory water absorption. The mortars with EPSP are provided with nearly the same compressive, flexural and tensile bond strengths as those of the control. EPSP has no notable influence on the paste hydration. But it can densify the mortar microstructures. It is also evident that heavy metal concentrations in leachates of the mortars with EPSP are far lower than the recommended in the GB5085.3-2007.

An Investigation into the Performances of Cement Mortar Incorporating Superabsorbent Polymer Synthesized with Kaolin

Cement-based materials are fundamental in the construction industry,and enhancing their properties is an ongoing challenge.The use of superabsorbent polymers(SAP)has gained significant attention as a possible way to improve the performance of cement-based materials due to their unique water-absorption and retention properties.This study investigates the multifaceted impact of kaolin intercalation-modified superabsorbent polymers(K-SAP)on the properties of cement mortar.The results show that K-SAP significantly affects the cement mortar’s rheological behavior,with distinct phases of water absorption and release,leading to changes in workability over time.Furthermore,K-SAP alters the hydration kinetics,delaying the exothermic peak of hydration and subsequently modifying the heat release kinetics.Notably,K-SAP effectively maintains a higher internal relative humidity within the mortar,reducing the autogenous shrinkage behavior.Moreover,K-SAP can have a beneficial effect on pore structure and this can be ascribed to the internal curing effect of released water from K-SAP.

Infuences of Different Admixtures on the Drying Shrinkage Characteristics of Metakaolin-based Geopolymer Mortar

To investigate the influences of different admixtures on the drying shrinkage of polymer mortar in a metakaolin base,the experiments of VAE(vinyl acetate ethylene copolymer),APAM(anionic polyacrylamide)and CPAM(cationic polyacrylamide)on the drying shrinkage properties of geopolymer mortar were designed under normal temperature curing conditions.An SP-175 mortar shrinkage dilatometer was introduced to measure the dry shrinkage of geopolymer mortar.Meanwhile,the drying shrinkage properties of geopolymer mortar are exhibited by the parameters of water loss rate,drying shrinkage rate,drying shrinkage strain and drying shrinkage coefficient.The experimental data are further fitted to obtain the prediction model of dry shrinkage of geopolymer mortar,which can better reflect the relationship between dry shrinkage rate and time.Finally,the experimental results demonstrate that the dry shrinkage of geopolymer mortar can be significantly increased by adding 4%VAE admixture,meanwhile under the condition that the polymer film formed by VAE reaction can strengthen and toughen the mortar.2.5%APAM admixture and 1.5%CPAM admixture can enhance the dry shrinkage performance of geopolymer mortar in a certain range.

Failure Characteristics of Rock-like Mortar Specimens with Arc-shaped Flaws under Freezing-thaw Cycles and Uniaxial Compression

To investigate the freeze-thaw(F-T)damages and failure characteristics of rock mass with arc-shaped joints in cold regions,three types of cement mortar specimens with different central angles and prefabricated arc-shaped flaws are subjected to uniaxial compressive tests under different F-T cycles.Experimental observations show that the uniaxial compressive strength of specimens are significantly influenced by F-T cycles and their failure modes are mainly affected by the central angleαof the prefabricated flaws.Unlike the specimens with a central angle of 60°,the specimens with a central angle of 120°and 180°have greater curvature of flaws,so tensile cracks occur in the arc-top area of their prefabricated flaws.According to experimental images observed by environmental scanning electron microscope(ESEM),as the number of F-T cycles increases,the deterioration effect of the specimen becomes more obvious,which is specifically reflected in the increase of the mass loss,peak stress loss,and damage variables as a power function,and the peak strain decreases as a quadratic polynomial.According to numerical results using two-dimensional particle flow code(PFC2D),it is found that F-T cycles cause more damage to the specimen in the early stages than in the later ones.The area of the concentrated compressive stress zone in the middle is decreased due to the increased number of F-T cycles,while the area of the surrounding tensile-shear stress zone is increased.The models appear different failure modes due to the release of concentrated stress in different tensile-shear zones.

Influence of Recycled Concrete Fine Powder on Durability of Cement Mortar

In this paper,the durability of cement mortar prepared with a recycled-concrete fine powder(RFP)was examined;including the analysis of a variety of aspects,such as the carbonization,sulfate attack and chloride ion erosion resistance.The results indicate that the influence of RFP on these three aspects is different.The carbonization depth after 30 days and the chloride diffusion coefficient of mortar containing 10%RFP decreased by 13.3%and 28.19%.With a further increase in the RFP content,interconnected pores formed between the RFP particles,leading to an acceleration of the penetration rate of CO_(2)and Cl^(−).When the RFP content was less than 50%,the corrosion resistance coefficient of the compressive strength of the mortar was 0.84-1.05 after 90 days of sulfate attack.But the expansion and cracking of the mortar was effectively alleviated due to decrease of the gypsum production.Scanning electron microscope(SEM)analysis has confirmed that 10%RFP contributes to the formation of a dense microstructure in the cement mortar.

Analysis of Calcined Red Mud Properties and Related Mortar Performances

Red mud(RM)is a low-activity industrial solid waste,and its utilization as a resource is currently a hot topic.In this study,the micro characteristics of red mud at different calcination temperatures were analyzed using X-ray diffraction and scanning electron microscopy.The performance of calcined red mud was determined through mortar strength tests.Results indicate that high-temperature calcination can change the mineral composition and microstructure of red mud,and increase the surface roughness and specific surface area.At the optimal temperature of 700°C,the addition of calcined red mud still leads to a decrease in mortar strength,but its activity index and flexural coefficient increase by 16.2%and 11.9%with respect to uncalcined red mud,reaching values of 0.826 and 0.974,respectively.Compared with the control group,the synergistic activation of calcined red mud with slag can increase the compressive and flexural strength of the mortar by 12.9%and 1.5%,reaching 8.7 and 62.4 MPa,respectively.Correspondingly,the activity index and flexural coefficient of the calcined RM and GGBS(Ground Granulated Blast furnace Slag)mixtures also increase to 1.015 and 1.130,respectively.

Effect of Partial Replacement of Fly Ash by Decoration Waste Powder on the Fresh and Mechanical Properties of Geopolymer Masonry Mortar

This study aims to investigate the feasibility of using decoration waste powder(DWP)as a partial replacement for fly ash(FA)in the preparation of geopolymer masonry mortar,and to examine the effect of different DWP replacement rates(0%-40%)on the fresh and mechanical properties of the mortar.The results showed that each group of geopolymer masonry mortar exhibited excellent water retention performance,with a water retention rate of 100%,which was due to the unique geopolymer mortar system and high viscosity of the alkaline activator solution.Compared to the control group,the flowability of the mortar containing lower contents of DWP(10%and 20%)was higher.However,as the DWP replacement rate further increased,the flowability gradually decreased.The DWP could absorb the free water in the reaction system of geopolymer mortar,thereby limiting the occurrence of geopolymerization reaction.The incorporation of DWP in the mortar resulted in a decrease in compressive strength compared to the mortar without DWP.However,even at a replacement rate of 40%,the compressive strength of the mortar still exceeded 15 MPa,which met the requirements of the masonry mortar.It was feasible to use DWP in the geopolymer masonry mortar.Although the addition of DWP caused some performance loss,it did not affect its usability.

Study on physical and mechanical properties of cement asphalt emulsified mortar under track slab

Purpose–During the construction process of the China Railway Track System(CRTS)I type filling layer,the nonwoven fabric bags have been used as grouting templates for cement asphalt(CA)emulsified mortar.The porous structure of nonwoven fabrics endowed the templates with breathability and water permeability.The standard requires that the volume expansion rate of CA mortar must be controlled within 1%–3%,which can generate expansion pressure to ensure that the cavities under track slabs are filled fully.However,the expansion pressure caused some of the water to seep out from the periphery of the filling bag,and it would affect the actual mix proportion of CA mortar.The differences in physical and mechanical properties between the CA mortar under track slabs and the CA mortar formed in the laboratory were studied in this paper.The relevant results could provide important methods for the research of filling layer materials for CRTS I type and other types of ballastless tracks in China.Design/methodology/approach–During the inspection of filling layer,the samples of CA mortar from different working conditions and raw materials were taken by uncovering the track slabs and drilling cores.The physical and mechanical properties of CA mortar under the filling layer of the slab were systematically analyzed by testing the electrical flux,compressive strength and density of mortar in different parts of the filling layer.Findings–In this paper,the electric flux,the physical properties and mechanical properties of different parts of CA mortar under the track slab were investigated.The results showed that the density,electric flux and compressive strength of CA mortar were affected by the composition of raw materials for dry powders and different parts of the filling layer.In addition,the electrical flux of CA mortar gradually decreased within 90 days’age.The electrical flux of samples with the thickness of 54 mm was lower than 500 C.Therefore,the impermeability and durability of CA mortar could be improved by increasing the thickness of filling layer.Besides,the results showed that the compressive strength of CA mortar increased,while the density and electric flux decreased gradually,with the prolongation of hardening time.Originality/value–During 90 days’age,the electrical flux of the CA mortar gradually decreased with the increase of specimen thickness and the electrical flux of the specimens with the thickness of 54 mm was lower than 500 C.The impermeability and durability of the CA mortar could be improved by increasing the thickness of filling layer.The proposed method can provide reference for the further development and improvement of CRTS I and CRTS II type ballastless track in China.

Influence of Ultra Fine Glass Powder on the Properties and Microstructure of Mortars

This study focuses on the effect of ultrafine waste glass powder on cement strength,gas permeability and pore structure.Varying contents were considered,with particle sizes ranging from 2 to 20μm.Moreover,alkali activation was considered to ameliorate the reactivity and cementitious properties,which were assessed by using scanning electron microscopy(SEM),energy-dispersive X-ray spectroscopy(EDS),and specific surface area pore size distribution analysis.According to the results,without the addition of alkali activators,the performance of glass powder mortar decreases as the amount of glass powder increases,affecting various aspects such as strength and resistance to gas permeability.Only 5%glass powder mortar demonstrated a compressive strength at 60 days higher than that of the control group.However,adding alkali activator(CaO)during hydration ameliorated the hydration environment,increased the alkalinity of the composite system,activated the reactivity of glass powder,and enhanced the interaction of glass powder and pozzolanic reaction.In general,compared to ordinary cement mortar,alkali-activated glass powder mortar produces more hydration products,showcases elevated density,and exhibits improved gas resistance.Furthermore,alkali-activated glass powder mortar demonstrates an improvement in performance across various aspects as the content increases.At a substitution rate of 15%,the glass powder mortar reaches its optimal levels of strength and resistance to gas permeability,with a compressive strength increase ranging from 28.4%to 34%,and a gas permeation rate reduction between 51.8%and 66.7%.

Research Analysis on the Microscopic Properties and Damping Performance of Carbon Nanomaterial-Modified Cement Mortar

The application of carbon nanomaterials, particularly graphene and carbon nanotubes, in cement-based composites is highly significant. These materials demonstrate the multifunctionality of carbon and offer extensive possibilities for technological advancements. This research analyzes how the integration of graphene into cement-based composites enhances damping and mechanical properties, thereby contributing to the safety and durability of structures. Research on carbon nanomaterials is ongoing and is expected to continue driving innovation across various industrial sectors, promoting the sustainable development of building materials.

Substitution of Aggregates in Concrete and Mortar with Coltan Mining Waste: Mechanical, Environmental, and Economic Impact Case Study

The mining process involves drilling and excavation, resulting in the production of waste rock and tailings. The waste materials are then removed and stored in designated areas. This study aims to evaluate the mechanical strength and the environmental and economic impact of using Coltan Mining Waste (CMW) as a substitute for aggregates in concrete and mortar production. To achieve this, the CMW needs to be characterised. The Dreux Gorisse method was primarily used to produce concrete with a strength of 20 MPa at 28 days. The mortars, on the other hand, were formulated according to the NF P 18-452 standard. The environmental impact of using CMW as substitutes for natural aggregates in the production of concrete and mortar was analysed using SimaPro software. The results showed that mortars and concrete made with CMW have comparable compressive strengths to the reference mortar and concrete;reduce the negative impact on ecosystem quality, human health, resources, and climate change. It has also been shown that the substitution of aggregates by CMW reduces the cost of concrete and mortar as a function of the distance from the aggregate footprint.

The Effect of Graphene Oxide on Mechanical Properties of Cement Mortar

Cement is widely used in engineering applications,but it has both the characteristics of high brittleness and poor bending resistance.In this paper,the effects of different amounts ofgraphene oxide on the flexural strength and compressive strength of cement mortar were studied by doping a certain amount of graphene oxide with cement mortar,and the strengthening mechanism of graphene oxide on cement mortar was obtained through microstructure detection.It is found that graphene oxide has a significant enhancement effect on the macroscopic mechanical properties of cement mortar,and graphene oxide provides nano-nucleation sites and growth templates for cement mortar,accelerates the hydration process,reduces the voids between hydration products,greatly increases the compactness,and improves the macroscopic properties of cement-based materials.