The reliability and deterministic analyses of wood-cored stiffened deep cement mixing and deep cement mixing column-supported embankments(referred to as WSCSE and DCSE,respectively)considering serviceability limit sta...The reliability and deterministic analyses of wood-cored stiffened deep cement mixing and deep cement mixing column-supported embankments(referred to as WSCSE and DCSE,respectively)considering serviceability limit state requirements are presented in this paper.Random field theory was used to simulate the spatial variability of soilcement mixing(SCM)material in which the adaptive Kriging Monte Carlo simulation was adopted to estimate the failure probability of a columnsupported embankment(CSE)system.A new method for stochastically generating random values of unconfined compressive strength(qu)and the ratio(Ru)between the undrained elastic modulus and qu of SCM material based on statistical correlation data is proposed.Reliability performance of CSEs concerning changes in the mean(μ),coefficient of variation(CoV),and vertical spatial correlation length(θv)of qu and Ru are presented and discussed.The obtained results indicate that WSCSE can provide a significantly higher reliability level and can tolerate more SCM material spatial variability than DCSE.Some performance of DCSE and WSCSE,which can be considered satisfactory in a deterministic framework,cannot guarantee an acceptable reliability level from a probabilistic viewpoint.This highlights the importance and necessity of employing reliability analyses for the design of CSEs.Moreover,consideration of only μ and CoV of qu seems to be sufficient for reliability analysis of WSCSE while for DCSE,uncertainties regarding the Ru(i.e.both μ and CoV)and θv of qu cannot be ignored.展开更多
A new configuration of coalescence-dispersed pulsed-sieve-plate extraction column (CDPSEC) was developed, and the mass transfer and axial mixing characteristics were evaluated with the two-point dynamic method.The inf...A new configuration of coalescence-dispersed pulsed-sieve-plate extraction column (CDPSEC) was developed, and the mass transfer and axial mixing characteristics were evaluated with the two-point dynamic method.The influence of operation conditions was discussed with experimental results, showing that the mass transfer performance of CDPSEC mainly depends on the energy input and the holdup of dispersed phase. Higher energy input results in higher holdup of the dispersed phase, the axial mixing of the continuous phase is suppressed, and the true height of mass transfer unit decreases markedly. On the other hand, higher energy input leads to more serious forward mixing of the dispersed phase, so the energy input should be limited. Accordingly the operation conditions were divided into two regions, and empirical correlations for predicting the mass transfer and axial mixing characteristics in different regions with a satisfactory accuracy were suggested.展开更多
1 INTRODUCTIONAnnular pulsed-sieve-plate extraction column is an unique extraction equipment that can beused to ensure critical safety in reprocssing of irradiated nuclear fuel,The study of this kind ofextraction colu...1 INTRODUCTIONAnnular pulsed-sieve-plate extraction column is an unique extraction equipment that can beused to ensure critical safety in reprocssing of irradiated nuclear fuel,The study of this kind ofextraction column has been carried out and some results were published in resent years [1—9]. It is known that axial mixing is one of most important parameters effecting column be-展开更多
Dry jet mixing (DJM) for soft soil stabilization has been widely used since 1980s. The quality and strength of stabilized columns are fundamental parameters to evaluate the stabilization work. This paper presents the ...Dry jet mixing (DJM) for soft soil stabilization has been widely used since 1980s. The quality and strength of stabilized columns are fundamental parameters to evaluate the stabilization work. This paper presents the standard penetration test (SPT) method and its test results on cement columns. It is shown that SPT is an effective and simple method for inspecting and evaluating cement columns. The strength characteristics along the length of the column, a good correction between SPT blow count and the unconfined compressive strength are achieved.展开更多
The consolidation behavior of mixed in place cement and lime/cement mixed column was studied. Consolidation of the composite foundation was modeled as a three dimensional axi symmetric problem. The authors used t...The consolidation behavior of mixed in place cement and lime/cement mixed column was studied. Consolidation of the composite foundation was modeled as a three dimensional axi symmetric problem. The authors used the finite difference method to obtain the pore pressure variation with time at any location below the surface. A computer program developed by the authors was used to draw some interesting conclusions about the consolidation behaviors of cement and lime/cement mixed pile foundation. Finally, a combined model including the permeability coefficients of cement mixed piles and soil, was studied and its feasibility was evaluated.展开更多
The open turbine rotating disc contactor (OTRDC) has been installed simply by adding three narrow strips to the lower surface of each rotating disc in the rotating disc contactor (RDC), so it can be used for the syste...The open turbine rotating disc contactor (OTRDC) has been installed simply by adding three narrow strips to the lower surface of each rotating disc in the rotating disc contactor (RDC), so it can be used for the system with high solid particle content. Hydrodynamics and axial mixing have been investigated in a 0.152m diameter OTRDC of different compartment height for the system of tap water and quartz particles. A model has been developed to describe the flow of liquid and solid phases. The solid phase holdup can be calculated satisfactorily according to the model equations. Axial mixing data have been treated by the backflow model and the correlations for predicting backflow ratios of liquid and solid phases in OTRDC have been presented.展开更多
Breakage and coalescence rates of droplets in reciprocating plate extraction columns were investigated bystep change in mixing intensity.Mean drop size was measured by laser light transmission technique combinedwith m...Breakage and coalescence rates of droplets in reciprocating plate extraction columns were investigated bystep change in mixing intensity.Mean drop size was measured by laser light transmission technique combinedwith measurement of local holdup.Batch and countercurrent flow experiments with and without mass transferoccurring show that the dispersion mechanisms are different.The Monte Carlo simulation by digital computerwas used to treat the experimental data and models of breakage and coalescence rates were obtained.展开更多
Residence time distribution (RTD) analysis of liquid phase was conducted in an internal airlift loop reactor (AL) and a bubble column (BC) with the tracer response technique. These data were simulated and compared thr...Residence time distribution (RTD) analysis of liquid phase was conducted in an internal airlift loop reactor (AL) and a bubble column (BC) with the tracer response technique. These data were simulated and compared through several flow mixing models. The modeling results of two-parameter model indicated that there were higher ratio of full mixing zones and lower ratio of bypass flow in AL than in BC. Then a completely mixed-plug flow parallel combined (four-parameter) model was established. Modeling results show that it is more precise and more obvious than two-parameter model.展开更多
To evaluate the influence of gas and liquid axial mixings on the separation efficiency of packed column, an approximate mathematical solution of HETP (equivalent height to a theoretical plate) under continuous operati...To evaluate the influence of gas and liquid axial mixings on the separation efficiency of packed column, an approximate mathematical solution of HETP (equivalent height to a theoretical plate) under continuous operation has been proposed based on the mixing pool model. The mass transfer and hydrodynamic data of structured packing, Mellapak 350Y, obtained in a high pressure tower have been used to test the validity of the proposed model. Compared with the SRP model and the Gualito model, it is found that for high pressure distillation process the present mathematical prediction shows a mean relative error of about 10% to the experimental data,the accuracy of which is the same as that by the Gualito model but better than that by the SRP model.展开更多
利用隔壁精馏塔替代混合碳五馏分原有分离流程中的脱丁烷塔和碳五预分离塔,通过Aspen Plus V12软件对混合碳五馏分的提纯流程进行稳态模拟,在此基础上运用灵敏度分析工具,对隔壁精馏塔的操作参数进行优化。结果表明:采用隔壁精馏塔替代...利用隔壁精馏塔替代混合碳五馏分原有分离流程中的脱丁烷塔和碳五预分离塔,通过Aspen Plus V12软件对混合碳五馏分的提纯流程进行稳态模拟,在此基础上运用灵敏度分析工具,对隔壁精馏塔的操作参数进行优化。结果表明:采用隔壁精馏塔替代脱丁烷塔和碳五预分离塔,最佳原料进料位置为第11块塔板、最佳质量回流比为5、最佳侧线采出位置为第7块塔板、最佳侧线采出量为500 kg h,气相回流位置为第37块塔板,液相回流位置为第12块塔板;在相同进料条件和相同碳五馏分纯度的前提下,与采用常规精馏工艺相比,采用隔壁塔精馏工艺时冷却能耗降低17.04%,加热能耗降低16.69%。展开更多
文摘The reliability and deterministic analyses of wood-cored stiffened deep cement mixing and deep cement mixing column-supported embankments(referred to as WSCSE and DCSE,respectively)considering serviceability limit state requirements are presented in this paper.Random field theory was used to simulate the spatial variability of soilcement mixing(SCM)material in which the adaptive Kriging Monte Carlo simulation was adopted to estimate the failure probability of a columnsupported embankment(CSE)system.A new method for stochastically generating random values of unconfined compressive strength(qu)and the ratio(Ru)between the undrained elastic modulus and qu of SCM material based on statistical correlation data is proposed.Reliability performance of CSEs concerning changes in the mean(μ),coefficient of variation(CoV),and vertical spatial correlation length(θv)of qu and Ru are presented and discussed.The obtained results indicate that WSCSE can provide a significantly higher reliability level and can tolerate more SCM material spatial variability than DCSE.Some performance of DCSE and WSCSE,which can be considered satisfactory in a deterministic framework,cannot guarantee an acceptable reliability level from a probabilistic viewpoint.This highlights the importance and necessity of employing reliability analyses for the design of CSEs.Moreover,consideration of only μ and CoV of qu seems to be sufficient for reliability analysis of WSCSE while for DCSE,uncertainties regarding the Ru(i.e.both μ and CoV)and θv of qu cannot be ignored.
文摘A new configuration of coalescence-dispersed pulsed-sieve-plate extraction column (CDPSEC) was developed, and the mass transfer and axial mixing characteristics were evaluated with the two-point dynamic method.The influence of operation conditions was discussed with experimental results, showing that the mass transfer performance of CDPSEC mainly depends on the energy input and the holdup of dispersed phase. Higher energy input results in higher holdup of the dispersed phase, the axial mixing of the continuous phase is suppressed, and the true height of mass transfer unit decreases markedly. On the other hand, higher energy input leads to more serious forward mixing of the dispersed phase, so the energy input should be limited. Accordingly the operation conditions were divided into two regions, and empirical correlations for predicting the mass transfer and axial mixing characteristics in different regions with a satisfactory accuracy were suggested.
文摘1 INTRODUCTIONAnnular pulsed-sieve-plate extraction column is an unique extraction equipment that can beused to ensure critical safety in reprocssing of irradiated nuclear fuel,The study of this kind ofextraction column has been carried out and some results were published in resent years [1—9]. It is known that axial mixing is one of most important parameters effecting column be-
文摘Dry jet mixing (DJM) for soft soil stabilization has been widely used since 1980s. The quality and strength of stabilized columns are fundamental parameters to evaluate the stabilization work. This paper presents the standard penetration test (SPT) method and its test results on cement columns. It is shown that SPT is an effective and simple method for inspecting and evaluating cement columns. The strength characteristics along the length of the column, a good correction between SPT blow count and the unconfined compressive strength are achieved.
文摘The consolidation behavior of mixed in place cement and lime/cement mixed column was studied. Consolidation of the composite foundation was modeled as a three dimensional axi symmetric problem. The authors used the finite difference method to obtain the pore pressure variation with time at any location below the surface. A computer program developed by the authors was used to draw some interesting conclusions about the consolidation behaviors of cement and lime/cement mixed pile foundation. Finally, a combined model including the permeability coefficients of cement mixed piles and soil, was studied and its feasibility was evaluated.
文摘The open turbine rotating disc contactor (OTRDC) has been installed simply by adding three narrow strips to the lower surface of each rotating disc in the rotating disc contactor (RDC), so it can be used for the system with high solid particle content. Hydrodynamics and axial mixing have been investigated in a 0.152m diameter OTRDC of different compartment height for the system of tap water and quartz particles. A model has been developed to describe the flow of liquid and solid phases. The solid phase holdup can be calculated satisfactorily according to the model equations. Axial mixing data have been treated by the backflow model and the correlations for predicting backflow ratios of liquid and solid phases in OTRDC have been presented.
文摘Breakage and coalescence rates of droplets in reciprocating plate extraction columns were investigated bystep change in mixing intensity.Mean drop size was measured by laser light transmission technique combinedwith measurement of local holdup.Batch and countercurrent flow experiments with and without mass transferoccurring show that the dispersion mechanisms are different.The Monte Carlo simulation by digital computerwas used to treat the experimental data and models of breakage and coalescence rates were obtained.
文摘Residence time distribution (RTD) analysis of liquid phase was conducted in an internal airlift loop reactor (AL) and a bubble column (BC) with the tracer response technique. These data were simulated and compared through several flow mixing models. The modeling results of two-parameter model indicated that there were higher ratio of full mixing zones and lower ratio of bypass flow in AL than in BC. Then a completely mixed-plug flow parallel combined (four-parameter) model was established. Modeling results show that it is more precise and more obvious than two-parameter model.
文摘To evaluate the influence of gas and liquid axial mixings on the separation efficiency of packed column, an approximate mathematical solution of HETP (equivalent height to a theoretical plate) under continuous operation has been proposed based on the mixing pool model. The mass transfer and hydrodynamic data of structured packing, Mellapak 350Y, obtained in a high pressure tower have been used to test the validity of the proposed model. Compared with the SRP model and the Gualito model, it is found that for high pressure distillation process the present mathematical prediction shows a mean relative error of about 10% to the experimental data,the accuracy of which is the same as that by the Gualito model but better than that by the SRP model.
文摘利用隔壁精馏塔替代混合碳五馏分原有分离流程中的脱丁烷塔和碳五预分离塔,通过Aspen Plus V12软件对混合碳五馏分的提纯流程进行稳态模拟,在此基础上运用灵敏度分析工具,对隔壁精馏塔的操作参数进行优化。结果表明:采用隔壁精馏塔替代脱丁烷塔和碳五预分离塔,最佳原料进料位置为第11块塔板、最佳质量回流比为5、最佳侧线采出位置为第7块塔板、最佳侧线采出量为500 kg h,气相回流位置为第37块塔板,液相回流位置为第12块塔板;在相同进料条件和相同碳五馏分纯度的前提下,与采用常规精馏工艺相比,采用隔壁塔精馏工艺时冷却能耗降低17.04%,加热能耗降低16.69%。
