High-performance grinding of ceramic matrix composites

Ceramic matrix composites(CMCs)are highly promising materials for the next generation of aero-engines.However,machining of CMCs suffers from low efficiency and poor surfacefinish,which presents an obstacle to their wider application.To overcome these problems,this study investigates high-efficiency deep grinding of CMCs,focusing on the effects of grinding depth.The results show that both the sur-face roughness and the depth of subsurface damage(SSD)are insensitive to grinding depth.The material removal rate can be increased sixfold by increasing the grinding depth,while the surface roughness and SSD depth increase by only about 10%.Moreover,it is found that the behavior of material removal is strongly dependent on grinding depth.As the grinding depth is increased,fibers are removed in smaller sizes,with thefiber length in chips being reduced by about 34%.However,too large a grinding depth will result in blockage by chip powder,which leads to a dramatic increase in the ratio of tangential to normal grinding forces.This study demonstrates that increasing the depth of cut is an effective approach to improve the machining efficiency of CMCs,while maintaining a good surfacefin-ish.It provides the basis for the further development of high-performance grinding methods for CMCs,which should facilitate their wider application.

EFFECT OF FIBER FAILURE ON QUASI-STATIC UNLOADING/RELOADING HYSTERESIS LOOPS OF CERAMIC MATRIX COMPOSITES

The two-parameter Weibull model is used to describe the fiber strength distribution.The stress carried by the intact and fracture fibers on the matrix crack plane during unloading/reloading is determined based on the global load sharing criterion.The axial stress distribution of intact fibers upon unloading and reloading is determined based on the mechanisms of fiber sliding relative to matrix in the interface debonded region.The interface debonded length,unloading interface counter slip length,and reloading interface new slip length are obtained by the fracture mechanics approach.The hysteresis loops corresponding to different stresses considering fiber failure are compared with the cases without considering fiber failure.The effects of fiber characteristic strength and fiber Weibull modulus on the fiber failure,the shape,and the area of the hysteresis loops are analyzed.The predicted quasi-static unloading/reloading hysteresis loops agree well with experimental data.

RESEARCH ON MATRIX CRACK EVOLUTION OF CROSS-PLY CERAMIC MATRIX COMPOSITE

The matrix crack evolution of cross-ply ceramic matrix composites under uniaxial tensile loading is investigated using the energy balance method.Under tensile loading,the cross-ply ceramic matrix composites have five damage modes.The cracking mode 3 contains transverse cracking,matrix cracking and fiber/matrix interface debonding.The cracking mode 5 only contains matrix cracking and fiber/matrix interface debonding.The cracking stress of modes 3 and 5 appearing between existing transverse cracks is determined.And the multiple matrix crack evolution of mode 3 is determined.The effects of ply thickness,fiber volume fraction,interface shear stress and interface debonding energy on the cracking stress and matrix crack evolution are analyzed.Results indicate that the cracking mode 3 is more likely to appear between transverse cracks for the SiC/CAS material.

EVOLUTION OF THE MICROCRACKS IN WHISKER TOUGHENING CERAMIC MATRIX COMPOSITES

The modified equivalent inclusion theory by the authors and the internal variable theory are employed to investigate the evolution of the microcracks in whisker toughening ceramics and the influence of the microcracks on the mechanical properties of the material. The effect of residual thermostrain, whisker content and aspect ratio is considered. The modulus, initial nonlinear load, strength and nonlinear constitutive relation are calculated and some important conclusions are given.

Preparation and Mechanical Properties of Al_2O_3/Al Laminated Ceramic Matrix Composites

Three series of Al2O3/Al laminated ceramic matrix composites,named SPA,SPV and HP,were fabricated by different methods.SPA and SPV were prepared using Al2O3 slices and Al slurry via screen printing and subsequent heat treatment in air or vacuum.HP samples were made by hot pressing the layered stack of Al foils and Al2O3 slices.SEM and XRD were applied to analyze the microstructure and the interlayer crystal phase.The bending strength,fracture toughness and fracture work of the samples made by the three methods were measured and compared.The results show that the composites have much better toughness and higher fracture work than the Al2O3 slice.Among the samples made by the three methods,the samples made by hot pressing have the optimum mechanical performance.The displacement-load curves and fracture mechanism were analyzed.

STUDY ON PREPARATION OF CERAMIC MATRIX COMPOSITE OF WC-Co ULTRAFINE POWDERS

The W -Co compound precursor powders with an average particle sife of 60 nm were prepared by the chemical coprecipitation as the raw materials of Na2WO1 and CoCl2 and as the reagents of HCI and NH3 ?H2O. After re-ducing and carburizing the precursor powders by hydrogen gas and CO-CO 2 mixture gas. the WC-Co composite povvders ivith an average particle size of 0. 18/wi can be obtained. The purity and particle size of powders -were analysed by XRD and TEM. respectively. Meanwhile, the key factors to influ-ence the reducing and carburizing process of powders were also studied.

Effect of Interfacial Bonding on the Toughening of Al_2O_3/Ni Ceramic Matrix Composites

The main Iimitation to the toughening of the α-Al2O3/Ni composite is the poor bonding atthe interface. which causes the nickel particles to be pulled-out during crack propagation with-out obvious plastic deformation. A proper control of oxygen content at the Al2O3-Ni interfacecan promote wetting at the intedece, and produce a mechanically interlocked and chemically strengthened intedece, causing most of the nickel particles to be stretched to failure and to expe-rience severe plastic deformation during crack propagation in the composite. Fracture toughnesstesting using a modified double cantilever beam method with in situ observation of crack prop-agation in a scanning electron microscope shows that the composite with the strengthenedinterface has a more desirable R-curve behaviour and a higher fracture toughness value than thenormal composite.

A review on additive manufacturing of ceramic matrix composites

Additive manufacturing(AM)of ceramic matrix composites(CMCs)has enabled the production of highly customized,geometrically complex and functionalized parts with significantly improved properties and functionality,compared to single-phase ceramic components.It also opens up a new way to shape damage-tolerant ceramic composites with co-continuous phase reinforcement inspired by natural ma-terials.Nowadays,a large variety of AM techniques has been successfully applied to fabricate CMCs,but variable properties have been obtained so far.This article provides a comprehensive review on the AM of ceramic matrix composites through a systematic evaluation of the capabilities and limitations of each AM technique,with an emphasis on reported results regarding the properties and potentials of AM man-ufactured ceramic matrix composites.

Propulsion tests on ultra-high-temperature ceramic matrix composites for reusable rocket nozzles

Ultra-high-temperature ceramic matrix composites(UHTCMCs)based on a ZrB_(2)/SiC matrix have been investigated for the fabrication of reusable nozzles for propulsion.Three de Laval nozzle prototypes,obtained by sintering with either hot pressing(HP)or spark plasma sintering(SPS),were tested 2-3 times in a hybrid rocket motor for proving reusability.Sections were extracted after oxidation tests to study the microstructural changes and oxidative and thermomechanical stresses induced by the repeated tests.Compared to a reference graphite nozzle,no measurable erosion was observed for the UHTCMC-based nozzles.The oxidation mechanism consisted in the formation of a ZrO_(2)intermediate layer,with a liquid silicon oxide(SiO_(2))layer on the surface that was displaced by the action of the gas flux towards the divergent part of the nozzle,protecting it from further oxidation.Both specimens obtained by HP and SPS displayed similar performance,with very slight differences,which were attributed to small changes in porosity.These tests demonstrated the capability of complex-shaped prototypes made of the developed UHTCMCs to survive repeated exposure to environments representative of a realistic space propulsion application,for overall operating time up to 30 s,without any failure nor measurable erosion,making a promising step towards the development of reusable rocket components.

Experimental Study on the Overall Cooling Effectiveness of Effusion-Cooling Ceramic Matrix Composite Platform

Ceramic matrix composite(CMC),with higher thermal limit and lower density relative to the superalloy,is regarded as the most important structural material for modern gas turbine engines.However,the anisotropic thermal conductivities caused by the weave patterns totally change the thermal conduction performance inside the solid domain.Therefore,the present study aims to use the infrared thermographic to measure the SiC/SiC composite platform with staggered effusion holes along with the superalloy platform.CMC platform is prepared by 2-D plain weave braid structure with chemical vapor infiltration(CVI)process.The temperature of mainstream is 900 K to match the real mainstream to coolant temperature ratio(T_(g)/T_(c)=1.5,2.1).The experimental was conducted with seven mass flow ratios(MFR=1.5%-4.5%).The results indicate that the thermal conductivity along the thickness direction is of great importance for the CMC platform.The superalloy platform obtains higher level of overall cooling effectiveness than CMC at T_(g)/T_(c)=1.5.However,the CMC platform achieves greater overall cooling effectiveness relative to superalloy at T_(g)/T_(c)=2.1.In addition,CMC platform presents enhanced uniformity of overall cooling effectiveness due to the larger in-plane thermal conductivity.

Numerical Simulation of Dynamic Response of Fiber Reinforced Ceramic Matrix Composite Beam with Matrix Cracks Using Multiscale Modeling

A multiscale method for simulating the dynamic response of ceramic matrix composite （CMC） with matrix cracks is developed. At the global level, the finite element method is employed to simulate the dynamic response of a CMC beam. While at the local level, the multiscale mechanical method is used to estimate the stress/strain response of the material. A distributed computing system is developed to speed up the simulation. The simulation of dynamic response of a Nicalon/CAS-II beam being subjected to harmonic loading is performed as a numerical example. The results show that both the stress/strain responses under tension and compressive loading are nonlinear. These conditions result in a different response compared with that of elastic beam, such as： 1） the displacement response is not symmetric about the axis of time; 2） in the condition of small external load, the response at first order natural frequency is limited within a finite range; 3） decreasing the matrix crack space will increase the displace- ment response of the beam.

Machining of SiC ceramic matrix composites:A review

Continuous fiber reinforced SiC ceramic matrix composites(FRCMCs-SiC)are currently the preferred material for hot section components,safety–critical components and braking components(in the aerospace,energy,transportation)with high value,and have triggered the demand for machining.However,the high brittleness,anisotropy,and heterogeneity of materials bring great challenges to machining,due to high mechanical and thermal loads,severe tool wear,and poor machining quality.With the increasing demand of FRCMCs-SiC parts,high-quality and high-efficient machining has become a hot issue.This review paper provides a detailed literature survey on the machining of FRCMCs-SiC.The material removal mechanism,defect form,and interfacial mechanical properties of FRCMCs-SiC were summarized.The machining processes of FRCMCs-SiC were introduced,and their respective advantages and disadvantages were compared.Given the low machinability(high hardness,high brittleness,anisotropy,and heterogeneity)of FRCMCs-SiC,preliminary experiments have proved that ultrasonic-assisted machining and laser-assisted machining have shown unique advantages in reducing force and tool wear,improving machining quality and machining efficiency.The machined surface integrity was discussed,the influence of process parameters on the machined surface quality was analyzed,and the machining defects of FRCMCs-SiC were summarized.But for FRCMCs-SiC,the existing quantitative evaluation of the machined surface integrity was weak and unsystematic.

Long-term ceramic matrix composite for aeroengine

Three strategies were proposed to prolong the service life of continuous fiber-reinforced silicon carbide ceramic matrix composite(CMC-SiC),which served as thermal-structure components of aeroengine at thermo-mechanical-oxygenic coupling environment.As for some thermal-structure components with low working stress,improving the degree of densification was crucial to prolong the service life,and the related process approaches were recited.If the thermal-structure components worked under moderate stress,the matrix cracking stress(σ^(mc))should be improved as far as possible.The fiber preform architecture,interface shear strength,residual thermal stress,and matrix strengthening were associated withσ_(mc)in this review.Introducing self-healing components was quite significant with the appearance of matrix microcracks when CMC-SiC worked at more severe environment for hundreds of hours.The damage can be sealed by glass phase originating from the reaction between self-healing components and oxygen.The effective self-healing temperature range of different self-healing components was first summarized and distinguished.The structure,composition,and preparation process of CMC-SiC should be systematically designed and optimized to achieve long duration target.

Recent progress in ceramic matrix composites reinforced with graphene nanoplatelets

Graphene nanoplatelets(GNPs)are considered to be one of the most promising new reinforcements due to their unique two-dimensional structure and remarkable mechanical properties.In addition,their impressive electrical and thermal properties make them attractive fillers for producing multifunctional ceramics with a wide range of applications.This paper reviews the current status of the research and development of graphene-reinforced ceramic matrix composite(CMC)materials.Firstly,we focused on the processing methods for effective dispersion of GNPs throughout ceramic matrices and the reduction of the porosity of CMC products.Then,the microstructure and mechanical properties are provided,together with an emphasis on the possible toughening mechanisms that may operate.Additionally,the unique functional properties endowed by GNPs,such as enhanced electrical/thermal conductivity,are discussed,with a comprehensive comparison in different ceramic matrices as oxide and nonoxide composites.Finally,the prospects and problems needed to be solved in GNPs-reinforced CMCs are discussed.

Frequency-dependent random fatigue of panel-type structures made of ceramic matrix composites

The panel-type structures used in aerospace engineering can be subjected to severe highfrequency acoustic loadings in service. This paper evaluates the frequency-dependent random fatigue of panel-type structures made of ceramic matrix composites（CMCs） under acoustic loadings. Firstly, the high-frequency random responses from the broadband random excitation will result in more stress cycles in a deinite period of time. The probability density distributions of stress amplitudes will be different in different frequency bandwidths, though the peak stress estimations are identical. Secondly, the fatigue properties of CMCs can be highly frequency-dependent. The fatigue evaluation method for the random vibration case is adopted to evaluate the fatigue damage of a representative stiffened panel structure. The frequency effect through S-N curves on random fatigue damage is numerically veriied. Finally, a parameter is demonstrated to characterize the mean vibration frequency of a random process, and hence this parameter can further be considered as a reasonable loading frequency in the fatigue tests of CMCs to obtain more reliable S-N curves.Therefore, the inluence of vibration frequency can be incorporated in the random fatigue model from the two perspectives.

Thermal shock fatigue behavior of TiC/Al_2O_3 composite ceramics

The thermal shock fatigue behaviors of pure hot-pressed alumina and 30 wt.% TiC/Al2O3 composites were studied. The effect of TiC and Al2O3 starting particle size on the mechanical properties of the composites was discussed. Indentation-quench test was conducted to evaluate the effect of thermal fatigue temperature difference （ΔT） and number of thermal cycles （Ⅳ） on fatigue crack growth （Δa）. The mechanical properties and thermal fatigue resistance of TiC/Al203 composites are remarkably improved by the addition of TiC. The thermal shock fatigue of monolithic alumina and TiC/Al2O3 composites is due to a ＂true＂ cycling effect （thermal fatigue）. Crack deflection and bridging are the predominant reasons for the improvement of thermal shock fatigue resistance of the composites.

A Numerical Study of Densification Behavior of Silicon Carbide Matrix Composites in Isothermal Chemical Vapor Infiltration

We studied the characteristics of two-scale pore structure of preform in the deposition process and the mass transfer of reactant gas in dual-scale pores, and observed the physiochemical phenomenon associated with the reaction. Thereby, we established mathematical models on two scales, respectively, preform and reactor. These models were used for the numerical simulation of the process of ceramic matrix composites densified by isothermal chemical vapor infiltration(ICVI). The models were used to carry out a systematic study on the influence of process conditions and the preform structure on the densification behaviors. The most important findings of our study are that the processing time could be reduced by about 50% without compromising the quality of the material, if the processing temperature is 950-1 000 ℃ for the first 70 hours and then raised to 1 100 ℃.

不同编织方式下陶瓷基复合材料表面流动特性数值计算研究

Ceramic matrix composites(CMCs) are one of the most promising materials in the field of gas turbines,with superior weight and thermal properties. Its surface morphology is different from the traditional casting airfoil components, which mainly comes from different weaving methods and different braided tow thickness. However, few people have studied the influence of surface morphology of ceramic matrix composites(CMCs) on the development of boundary layer and the resulting flow loss. In this paper, Tex Gen is used to generate different surface morphology structures of ceramic matrix composites(CMCs), and the surface flow characteristics of corresponding CMCs plates are numerically studied. It is found that the slope of the displacement thickness of the woven surface first increases and then decreases in the whole transition interval. Thicker braided tow thickness and denser braiding method will induce earlier flow transition phenomenon and produce greater flow loss;The flow loss on the surface of CMCs plate is mainly composed of the vortex loss in the pit and the boundary layer loss outside the pit, and the boundary layer loss is dominant. The weaving methods has a greater influence on the flow state and flow loss of the boundary layer.

Preparation and properties of C/C-SiC brake composites fabricated by warm compacted-in situ reaction

Carbon fibre reinforced carbon and silicon carbide dual matrix composites（C/C-SiC） were fabricated by the warm compacted-in situ reaction.The microstructure,mechanical properties,tribological properties,and wear mechanism of C/C-SiC composites at different brake speeds were investigated.The results indicate that the composites are composed of 58wt%C,37wt%SiC,and 5wt%Si.The density and open porosity are 2.0 g.cm^（-3） and 10%,respectively.The C/C-SiC brake composites exhibit good mechanical properties.The flexural strength can reach up to 160 MPa,and the impact strength can reach 2.5 kJ.m^（-2）.The C/C-SiC brake composites show excellent tribological performances.The friction coefficient is between 0.57 and 0.67 at the brake speeds from 8 to 24 m·s^（-1）.The brake is stable,and the wear rate is less than 2.02×10^（-6） cm^3·J^（-1）.These results show that the C/C-SiC brake composites are the promising candidates for advanced brake and clutch systems.

Influences of Mechanical Vibration on Rapidly Solidified Al_2O_3/YSZ Ceramics Prepared by Combustion Synthesis

Al2O3/YSZ composite ceramics was fabricated with combustion synthesis technology, and the influences of mechanical vibration on its microstructures and properties were investigated. It is found that under the mechanical vibration of ever-increasing frequency, increasing combustion temperature, accelerating ceramics/metal liquid-liquid separation and quickening ceramic solidification could not only reduce the average diameter and the size distribution of aligned ZrO2 nano-micron fibers in rod-shaped Al2O3 matrix grains, but also make the randomly-oriented rod-shaped grains finer and increase their aspect ratios. As a result, a remarkable increase in flexural strength and fracture toughness of the ceramics can be observed.