The microstructure and mechanical properties of cast inserted dies for automobile covering components were studied. The results show that the as-cast microstructures of cast inserted dies are composed of pearlite, mar...The microstructure and mechanical properties of cast inserted dies for automobile covering components were studied. The results show that the as-cast microstructures of cast inserted dies are composed of pearlite, martensite, bainite, and austenite; and that the annealed microstructure is granular pearlite. The mechanical properties of cast inserted dies approach that of forged inserted dies. The tensile strength is 855 MPa, the elongation is 16%, the impact toughness is 177 J/cm2, and the hardness after annealing and quenching are HRC 19 and HRC 60-62. In addition, the cast inserted dies have good hardenability. The depth of the hardening zone and the hardness after flame quenching satisfy the operating requirements. The cast inserted dies could completely replace the forged inserted dies for making the dies of automobile covering components.展开更多
Through quantitative statistics and morphological characterization of ceramic fragments for ceramic composite bulletproof insert plates(CCBIPs),distribution characteristics of ceramic fragments within a specific size ...Through quantitative statistics and morphological characterization of ceramic fragments for ceramic composite bulletproof insert plates(CCBIPs),distribution characteristics of ceramic fragments within a specific size range were analyzed for different Armor Piercing Incendiary(API)and shot times.To quantitatively evaluate the effect of energy absorption for ceramic plates,a model of energy absorption during penetration for CCBIPs was established based on statistics of the size distribution of ceramic fragments(SDCF).Variation in the SDCF and its influence on energy absorption for CCBIPs were investigated.The results indicate that the distribution feature of ceramic fragments in the range of 0.25-2.25 mm is Gaussian distribution.Compared with Type 56 of API(56-API),ceramic fragments formed by 53-API with higher kinetic energy possess more quantity and more concentrated distribution,whose average equivalence size decreases by 6.5%,corresponding to increasing by 83.9%of estimated energy absorption.Besides,the ability of CCBIPs to resist the third shot is significantly weakened,whose estimated energy absorption decreases by 58.8%compared with the first shot.More concentrated distribution and fewer fragments are formed after the third shot,the average equivalence size of ceramic fragments increases by 6.9%,which may attribute to the micro-cracks induced by the previous two shots.展开更多
The effects of Si content on combinations of important properties such as hardness, hardenability, and weldability in addition to strength increment were systematically investigated to develop a Mo and V free low allo...The effects of Si content on combinations of important properties such as hardness, hardenability, and weldability in addition to strength increment were systematically investigated to develop a Mo and V free low alloy cast steel for automobile cold pressing die insert. For the evaluation of the applicability as the die insert, the mechanical properties were measured after spheroidization annealing （SA）, quenching and tempering （Q/T）, and flame hardening （FH） treatments, respectively. The developed 0.8%-1.6%Si containing Mo and V free alloy cast steels showed excellent matrix strengthening effect, hardenability, and weldability, fulfilling the industrial criterion of the mechanical properties for the die insert.展开更多
Firstly,the relation between the coefficient of thermal expansion(CTE)and the volume fraction of TiO_(2) was investigated, and also the influence of relative density of ceramic on the CTE was studied.The results show ...Firstly,the relation between the coefficient of thermal expansion(CTE)and the volume fraction of TiO_(2) was investigated, and also the influence of relative density of ceramic on the CTE was studied.The results show that the volume fraction of TiO_(2) and the relative density both make influence on the CTE of ZrO_(2)-TiO_(2) ceramic.According to the results,the ZrO_(2)-TiO_(2)(volume fraction of TiO_(2) is 27%)ceramic die with the similar CTE(8.92×10^(-6) ℃^(-1))to Ti6Al4V was fabricated.Secondly,to evaluate the dimensional accuracy of the workpiece superplastically formed,the Ti6Al4V impression experiment was performed.The result shows that the dimensional inaccuracy of workpiece is 0.003.Thirdly,in order to evaluate the practicability,the experiment of superplastic forming Ti6Al4V using ZrO_(2)-TiO_(2) cylinder ceramic die was carried out.The Ti6Al4V cylinder shows good shape retention and surface quality,and high dimensional accuracy.The ceramic dies seem to be adequate for superplastic forming the high accuracy Ti6Al4V, and the trials have confirmed the potential of the ZrO_(2)-TiO_(2) ceramic die.展开更多
A novel ceramic cemented carbide compact insert was developed using hot pressing sintering technique. The surface layers of the sandwich material were ceramic and the middle layer was cemented carbide. The factors tha...A novel ceramic cemented carbide compact insert was developed using hot pressing sintering technique. The surface layers of the sandwich material were ceramic and the middle layer was cemented carbide. The factors that affect the properties of the compact insert were analyzed. Theoretical analyses and experiments indicated that the cemented carbide with greater elastic module and thermal expansion coefficient than ceramic should be used in the sandwich material in order to get high equivalent flexure strength and the geometric parameters of the compact insert are also important to its properties.展开更多
Development and application of new ceramic die materials is one of the important topics in the field of die research. The composition, processing technology, mechanical property and engineering performance of the cera...Development and application of new ceramic die materials is one of the important topics in the field of die research. The composition, processing technology, mechanical property and engineering performance of the ceramic materials such as cermet, ZTA, TZP, TZP/Al2O3, TZP/TiC/Al2O3, PSZ and Sialon, etc., with rare earth yttrium, lanthanum and cerium, and so on working as additives, were investigated and analyzed in the present study. Problems existed in the research and application of rare earth ceramic die materials were discussed. Rare earth additives can effectively improve the mechanical property and engineering performance of ceramic die materials. Thus, it will have further perspectives of wider application. More attention should be paid in the future to the toughening and strengthening of the ceramic die materials, the adding forms and kinds of rare earth elements and acting mechanisms of rare earth additives in ceramic die materials.展开更多
The performances of ceramic inserts in cutting nickel-based alloy were investigated. A new cutting test-bed was devised and used to deburr. The burr height on the working surface with notch wear in deburring cutting w...The performances of ceramic inserts in cutting nickel-based alloy were investigated. A new cutting test-bed was devised and used to deburr. The burr height on the working surface with notch wear in deburring cutting was compared with that in normal cutting. The impact force, impact pressure, and impact frequency of the saw-tooth-shaped chip edge on rake face and cutting edge at different speeds were calculated, and the influence of chip edge on notch wear formation was analyzed. A new tool design for reducing notch wear was presented, which is flexible and can deburr effectively.展开更多
Wear resistance of several zirconia toughened ceramics in comparison with a metal-ceramic Co-WC has been studied in drawing wire field test. Result indicates that the harder the ceramic die, the longer the service lif...Wear resistance of several zirconia toughened ceramics in comparison with a metal-ceramic Co-WC has been studied in drawing wire field test. Result indicates that the harder the ceramic die, the longer the service life. Excellent wear resistance of ceramic die is obtained with a very high hardness (19 GPa). The service life is nearly three times that of Co-WC die. SEM observation on wear surfaces showed that material removal is mainly caused by plastic flow and ploughing process. But when the ceramic is composed of zirconia, alumina and some titanium carbide, micro-chipping and tribochemical reaction take place, and wear rate increases. Wear and friction induced martensite was detected by XRD. The T-M (tetragonal to monoclinic) phase transformation has a contribution to inhibiting microfracture.展开更多
Duplexα/β-SiAlON ceramic cutting inserts(30α:70β)were synthesized by microwave sintering.The effects of solid solution parameters(m,n,z),synthesis temperature,and amount of excess Y_(2)O_(3) synthesis additive on ...Duplexα/β-SiAlON ceramic cutting inserts(30α:70β)were synthesized by microwave sintering.The effects of solid solution parameters(m,n,z),synthesis temperature,and amount of excess Y_(2)O_(3) synthesis additive on phase assemblage,microstructure,mechanical properties,and cutting performance were systematically investigated.It was found that increasing m value could improve the formation ofαphase while high z value over 1.0 resulted in the dissolution ofαphase intoβphase and intergranular phase.Increasing the amount of excess Y_(2)O_(3) could promote densification and elongatedβgrain growth;however,the excess Y_(2)O_(3) amount above 4 wt%resulted in substantial crystallization of M'SS phase,thus declining the mechanical properties and wear resistance.The microwave-synthesizedα/β-SiAlON cutting insert with modified parameters(m=1.7,n=1.0,z=0.7,and 3 wt%excess Y_(2)O_(3))was obtained with optimal comprehensive properties,whose tool life was found to increase by approximately 75%in high-speed milling of Inconel 718 superalloy compared to the commercialα/β-SiAlON cutting insert.展开更多
SINCE the 1970s coated cemented carbide tools have been developed so as to further improvetheir wear and heat resistance. For the coated tools, cemented carbide with high strength andfracture toughness are selected as...SINCE the 1970s coated cemented carbide tools have been developed so as to further improvetheir wear and heat resistance. For the coated tools, cemented carbide with high strength andfracture toughness are selected as matrix materials, carbide, boride and nitride with highhardness are used as coating materials. Because the coating thickness of the coated tools is gen-展开更多
The development and research of titanium cast alloy and its casting technology, especially its application in aeronautical industry in China are presented. The technology of molding, melting and casting of titanium al...The development and research of titanium cast alloy and its casting technology, especially its application in aeronautical industry in China are presented. The technology of molding, melting and casting of titanium alloy, casting quality control are introduced. The existing problems and development trend in titanium alloy casting technology are also discussed.展开更多
The present work compares microstructures of hot work steels made by different processes, that is, by sprayforming,by casting, and a commercially supplied H13 steel. Material benefits are recognized by sprayforming ho...The present work compares microstructures of hot work steels made by different processes, that is, by sprayforming,by casting, and a commercially supplied H13 steel. Material benefits are recognized by sprayforming hot working tools such as die inserts for hot forging. The sprayformed hot work steels present a fine and homogeneous microstructure,which implies that, at a similar toughness level, the sprayformed steel can be higher alloyed, so that the thermal fatigue and wear resistance at elevated temperatures can be improved. A series of steels with higher vanadium content than commercial hot work steels are developed. There are no segregation and carbide network problems usually encountered in conventional ingot/forging processed high-vanadium steels. Microstructure and hardness of the new sprayformed steels are studied under different heat treatment conditions. It is justified that these sprayformed steels can be directly used for tooling without high temperature hardening. Sprayforming the tool steels onto a precision ceramic mould is demonstrated to extend the technoeconomical benefits, so that a net shape production tool can be rapidly made.Features of the rapid tooling process are also discussed.展开更多
文摘The microstructure and mechanical properties of cast inserted dies for automobile covering components were studied. The results show that the as-cast microstructures of cast inserted dies are composed of pearlite, martensite, bainite, and austenite; and that the annealed microstructure is granular pearlite. The mechanical properties of cast inserted dies approach that of forged inserted dies. The tensile strength is 855 MPa, the elongation is 16%, the impact toughness is 177 J/cm2, and the hardness after annealing and quenching are HRC 19 and HRC 60-62. In addition, the cast inserted dies have good hardenability. The depth of the hardening zone and the hardness after flame quenching satisfy the operating requirements. The cast inserted dies could completely replace the forged inserted dies for making the dies of automobile covering components.
基金financially supported by the National Key Research&Development Project(2017YFB1103505)the Military Logistics Research Program(XXXC002)of China。
文摘Through quantitative statistics and morphological characterization of ceramic fragments for ceramic composite bulletproof insert plates(CCBIPs),distribution characteristics of ceramic fragments within a specific size range were analyzed for different Armor Piercing Incendiary(API)and shot times.To quantitatively evaluate the effect of energy absorption for ceramic plates,a model of energy absorption during penetration for CCBIPs was established based on statistics of the size distribution of ceramic fragments(SDCF).Variation in the SDCF and its influence on energy absorption for CCBIPs were investigated.The results indicate that the distribution feature of ceramic fragments in the range of 0.25-2.25 mm is Gaussian distribution.Compared with Type 56 of API(56-API),ceramic fragments formed by 53-API with higher kinetic energy possess more quantity and more concentrated distribution,whose average equivalence size decreases by 6.5%,corresponding to increasing by 83.9%of estimated energy absorption.Besides,the ability of CCBIPs to resist the third shot is significantly weakened,whose estimated energy absorption decreases by 58.8%compared with the first shot.More concentrated distribution and fewer fragments are formed after the third shot,the average equivalence size of ceramic fragments increases by 6.9%,which may attribute to the micro-cracks induced by the previous two shots.
文摘The effects of Si content on combinations of important properties such as hardness, hardenability, and weldability in addition to strength increment were systematically investigated to develop a Mo and V free low alloy cast steel for automobile cold pressing die insert. For the evaluation of the applicability as the die insert, the mechanical properties were measured after spheroidization annealing （SA）, quenching and tempering （Q/T）, and flame hardening （FH） treatments, respectively. The developed 0.8%-1.6%Si containing Mo and V free alloy cast steels showed excellent matrix strengthening effect, hardenability, and weldability, fulfilling the industrial criterion of the mechanical properties for the die insert.
文摘Firstly,the relation between the coefficient of thermal expansion(CTE)and the volume fraction of TiO_(2) was investigated, and also the influence of relative density of ceramic on the CTE was studied.The results show that the volume fraction of TiO_(2) and the relative density both make influence on the CTE of ZrO_(2)-TiO_(2) ceramic.According to the results,the ZrO_(2)-TiO_(2)(volume fraction of TiO_(2) is 27%)ceramic die with the similar CTE(8.92×10^(-6) ℃^(-1))to Ti6Al4V was fabricated.Secondly,to evaluate the dimensional accuracy of the workpiece superplastically formed,the Ti6Al4V impression experiment was performed.The result shows that the dimensional inaccuracy of workpiece is 0.003.Thirdly,in order to evaluate the practicability,the experiment of superplastic forming Ti6Al4V using ZrO_(2)-TiO_(2) cylinder ceramic die was carried out.The Ti6Al4V cylinder shows good shape retention and surface quality,and high dimensional accuracy.The ceramic dies seem to be adequate for superplastic forming the high accuracy Ti6Al4V, and the trials have confirmed the potential of the ZrO_(2)-TiO_(2) ceramic die.
文摘A novel ceramic cemented carbide compact insert was developed using hot pressing sintering technique. The surface layers of the sandwich material were ceramic and the middle layer was cemented carbide. The factors that affect the properties of the compact insert were analyzed. Theoretical analyses and experiments indicated that the cemented carbide with greater elastic module and thermal expansion coefficient than ceramic should be used in the sandwich material in order to get high equivalent flexure strength and the geometric parameters of the compact insert are also important to its properties.
基金Project supported by National Natural Science Foundation of China (50405047)Natural Science foundation of Shandong Province (Y2005F04)Jinan Young Star Plan of Science and Technology (08108)
文摘Development and application of new ceramic die materials is one of the important topics in the field of die research. The composition, processing technology, mechanical property and engineering performance of the ceramic materials such as cermet, ZTA, TZP, TZP/Al2O3, TZP/TiC/Al2O3, PSZ and Sialon, etc., with rare earth yttrium, lanthanum and cerium, and so on working as additives, were investigated and analyzed in the present study. Problems existed in the research and application of rare earth ceramic die materials were discussed. Rare earth additives can effectively improve the mechanical property and engineering performance of ceramic die materials. Thus, it will have further perspectives of wider application. More attention should be paid in the future to the toughening and strengthening of the ceramic die materials, the adding forms and kinds of rare earth elements and acting mechanisms of rare earth additives in ceramic die materials.
文摘The performances of ceramic inserts in cutting nickel-based alloy were investigated. A new cutting test-bed was devised and used to deburr. The burr height on the working surface with notch wear in deburring cutting was compared with that in normal cutting. The impact force, impact pressure, and impact frequency of the saw-tooth-shaped chip edge on rake face and cutting edge at different speeds were calculated, and the influence of chip edge on notch wear formation was analyzed. A new tool design for reducing notch wear was presented, which is flexible and can deburr effectively.
文摘Wear resistance of several zirconia toughened ceramics in comparison with a metal-ceramic Co-WC has been studied in drawing wire field test. Result indicates that the harder the ceramic die, the longer the service life. Excellent wear resistance of ceramic die is obtained with a very high hardness (19 GPa). The service life is nearly three times that of Co-WC die. SEM observation on wear surfaces showed that material removal is mainly caused by plastic flow and ploughing process. But when the ceramic is composed of zirconia, alumina and some titanium carbide, micro-chipping and tribochemical reaction take place, and wear rate increases. Wear and friction induced martensite was detected by XRD. The T-M (tetragonal to monoclinic) phase transformation has a contribution to inhibiting microfracture.
基金The work is supported by the National Natural Science Foundation of China(Nos.51875291 and 52075266)the Excellent Youth Fund of Jiangsu Province(No.BK20190070)the Fundamental Research Funds for the Central Universities(No.30920032206).
文摘Duplexα/β-SiAlON ceramic cutting inserts(30α:70β)were synthesized by microwave sintering.The effects of solid solution parameters(m,n,z),synthesis temperature,and amount of excess Y_(2)O_(3) synthesis additive on phase assemblage,microstructure,mechanical properties,and cutting performance were systematically investigated.It was found that increasing m value could improve the formation ofαphase while high z value over 1.0 resulted in the dissolution ofαphase intoβphase and intergranular phase.Increasing the amount of excess Y_(2)O_(3) could promote densification and elongatedβgrain growth;however,the excess Y_(2)O_(3) amount above 4 wt%resulted in substantial crystallization of M'SS phase,thus declining the mechanical properties and wear resistance.The microwave-synthesizedα/β-SiAlON cutting insert with modified parameters(m=1.7,n=1.0,z=0.7,and 3 wt%excess Y_(2)O_(3))was obtained with optimal comprehensive properties,whose tool life was found to increase by approximately 75%in high-speed milling of Inconel 718 superalloy compared to the commercialα/β-SiAlON cutting insert.
文摘SINCE the 1970s coated cemented carbide tools have been developed so as to further improvetheir wear and heat resistance. For the coated tools, cemented carbide with high strength andfracture toughness are selected as matrix materials, carbide, boride and nitride with highhardness are used as coating materials. Because the coating thickness of the coated tools is gen-
基金The paper is support by Foundation Key Project of Yunnan:The Study on inoculated theory and reliability of low carbonductile iron, NO. 1999E0004Z
文摘The development and research of titanium cast alloy and its casting technology, especially its application in aeronautical industry in China are presented. The technology of molding, melting and casting of titanium alloy, casting quality control are introduced. The existing problems and development trend in titanium alloy casting technology are also discussed.
文摘The present work compares microstructures of hot work steels made by different processes, that is, by sprayforming,by casting, and a commercially supplied H13 steel. Material benefits are recognized by sprayforming hot working tools such as die inserts for hot forging. The sprayformed hot work steels present a fine and homogeneous microstructure,which implies that, at a similar toughness level, the sprayformed steel can be higher alloyed, so that the thermal fatigue and wear resistance at elevated temperatures can be improved. A series of steels with higher vanadium content than commercial hot work steels are developed. There are no segregation and carbide network problems usually encountered in conventional ingot/forging processed high-vanadium steels. Microstructure and hardness of the new sprayformed steels are studied under different heat treatment conditions. It is justified that these sprayformed steels can be directly used for tooling without high temperature hardening. Sprayforming the tool steels onto a precision ceramic mould is demonstrated to extend the technoeconomical benefits, so that a net shape production tool can be rapidly made.Features of the rapid tooling process are also discussed.
