A fully-differential charge pump（FDCP）with perfect current matching and low output current noise is realized for phase-locked loops（PLLs）.An easily stable common-mode feedback（CMFB）circuit which can handle high ...A fully-differential charge pump（FDCP）with perfect current matching and low output current noise is realized for phase-locked loops（PLLs）.An easily stable common-mode feedback（CMFB）circuit which can handle high input voltage swing is proposed.Current mismatch and current noise contribution from the CMFB circuit is minimized.In order to optimize PLL phase noise,the output current noise of the FDCP is analyzed in detail and calculated with the sampling principle.The calculation result agrees well with the simulation.Based on the noise analysis,many methods to lower output current noise of the FDCP are discussed.The fully-differential charge pump is integrated into a 1–2 GHz frequency synthesizer and fabricated in an SMIC CMOS 0.18μm process.The measured output reference spur is–64 dBc to–69 dBc.The in-band and out-band phase noise is–95 dBc/Hz at 3 kHz frequency offset and–123 dBc/Hz at 1 MHz frequency offset respectively.展开更多
Two essential blocks for the PLLs based on CP, a phase-frequency detector （PFD） and an improved current steering charge-pump （CP）, are developed. The mechanisms for widening the phase error detection range and eli...Two essential blocks for the PLLs based on CP, a phase-frequency detector （PFD） and an improved current steering charge-pump （CP）, are developed. The mechanisms for widening the phase error detection range and eliminating the dead zone are analyzed and applied in our design to optimize the proposed PFD. To obtain excellent current matching and minimum current variation over a wide output voltage range, an improved structure for the proposed CP is developed by fully utilizing many additional sub-circuits. Implemented in a standard 90-nm CMOS process, the proposed PFD achieves a phase error detection range from -354° to 354° and the improved CP demonstrates a current mismatch of less than 1.1% and a pump-current variation of 4% across the output voltage, swinging from 0.2 to 1.1 V, and the power consumption is 1.3 mW under a 1.2-V supply.展开更多
A new high performance charge pump circuit is designed and realized in 0.18μm CMOS process. A wide input ranged rail-to-rail operational amplifier and self-biasing cascode current mirror are used to enable the charge...A new high performance charge pump circuit is designed and realized in 0.18μm CMOS process. A wide input ranged rail-to-rail operational amplifier and self-biasing cascode current mirror are used to enable the charge pump current to be well matched in a wide output voltage range.Furthermore,a method of adding a precharging current source is proposed to increase the initial charge current,which will speed up the settling time of CPPLLs.Test results show that the current mismatching can be less than 0.4%in the output voltage range of 0.4 to 1.7 V,with a charge pump current of 100μA and a precharging current of 70μA.The average power consumption of the charge pump in the locked condition is around 0.9 mW under a 1.8 V supply voltage.展开更多
基金supported by the National High Technology Research and Development Program of China(No.2007AA01Z282)the National Natural Science Foundation of China(No.60876019)
文摘A fully-differential charge pump（FDCP）with perfect current matching and low output current noise is realized for phase-locked loops（PLLs）.An easily stable common-mode feedback（CMFB）circuit which can handle high input voltage swing is proposed.Current mismatch and current noise contribution from the CMFB circuit is minimized.In order to optimize PLL phase noise,the output current noise of the FDCP is analyzed in detail and calculated with the sampling principle.The calculation result agrees well with the simulation.Based on the noise analysis,many methods to lower output current noise of the FDCP are discussed.The fully-differential charge pump is integrated into a 1–2 GHz frequency synthesizer and fabricated in an SMIC CMOS 0.18μm process.The measured output reference spur is–64 dBc to–69 dBc.The in-band and out-band phase noise is–95 dBc/Hz at 3 kHz frequency offset and–123 dBc/Hz at 1 MHz frequency offset respectively.
基金Project supported by the National Basic Research Program of China(No.2010CB327404)the National High Technology Research and Development Program(No.2011AA10305)the National Natural Science Foundation of China(No.60901012)
文摘Two essential blocks for the PLLs based on CP, a phase-frequency detector （PFD） and an improved current steering charge-pump （CP）, are developed. The mechanisms for widening the phase error detection range and eliminating the dead zone are analyzed and applied in our design to optimize the proposed PFD. To obtain excellent current matching and minimum current variation over a wide output voltage range, an improved structure for the proposed CP is developed by fully utilizing many additional sub-circuits. Implemented in a standard 90-nm CMOS process, the proposed PFD achieves a phase error detection range from -354° to 354° and the improved CP demonstrates a current mismatch of less than 1.1% and a pump-current variation of 4% across the output voltage, swinging from 0.2 to 1.1 V, and the power consumption is 1.3 mW under a 1.2-V supply.
基金Project supported by the National High Technology Research and Development Program of China(No.2007AA01Z2A7)
文摘A new high performance charge pump circuit is designed and realized in 0.18μm CMOS process. A wide input ranged rail-to-rail operational amplifier and self-biasing cascode current mirror are used to enable the charge pump current to be well matched in a wide output voltage range.Furthermore,a method of adding a precharging current source is proposed to increase the initial charge current,which will speed up the settling time of CPPLLs.Test results show that the current mismatching can be less than 0.4%in the output voltage range of 0.4 to 1.7 V,with a charge pump current of 100μA and a precharging current of 70μA.The average power consumption of the charge pump in the locked condition is around 0.9 mW under a 1.8 V supply voltage.
