Determination of 14 Organophosphorus Pesticide Residues in Mutton by Gel Permeation Chromatography-Gas Chromatography-Mass Spectrometry(GPC-GC-MS)

[Objectives]This study was conducted to purify mutton samples by gel permeation chromatography(GPC).[Methods]Fourteen organophosphorus pesticide residues in samples were qualitatively and quantitatively analyzed by gas chromatography-mass spectrometry(GC-MS)in selective ion scanning mode(SIM).[Results]The organophosphorus pesticide standard solutions showed good linearity in the mass concentration range of 0.1-10.0μg/ml with correlation coefficients(r)not lower than 0.999,and the detection limits(S=3 N)ranged from 0.01 to 0.05 mg/kg.The average recovery values were in the range of 80.2%-99.7%,with relative standard deviations(RSDs,n=3)in the range of 1.8%-6.3%,at the addition levels of 0.5,1.0 and 2.0 mg/kg.[Conclusions]The method is simple,sensitive and accurate,and can be used for the determination of organophosphorus pesticide residues in mutton.

Gel Permeation Chromatography Purification and Gas Chromatography-Mass Spectrometry Detection of Multi-Pesticide Residues in Traditional Chinese Medicine

The measurement of 23 organochlorine, organophosphorus, and pyrethroid pesticides in typical traditional Chinese medicine (TCM), flos lonicerae, was made using gel permeation chromatography (GPC) purification and gas chroma- tography-mass spectrometry (GC-MS) detection. The pesticides were extracted with ultrasonic device and 5.0 mL mixture of ethyl acetate and cyclohexane (1:1, v/v). Coextractants from sample matrices which may have interfere to the qualitative and quantitative analysis, such as pigments, were removed using GPC purification. Simultaneous full scan and selective ion monitor (scan/SIM) mode for GC-MS was used for qualitative and quantitative analysis, which pro- vided retention time and characteristic fragments ratio for each pesticide so as to positively identify each analyte. Rela- tive standard deviations (RSDs) were within 7.7% (5.0 - 22.5 μg/kg, n = 3). The recoveries of pesticide standards at the spiked concentration of 5.0 - 22.5 μg/kg were between 87.1% and 110.9%. Limits of detection (LODs) for the analytes were 0.16 - 3.2 μg/kg, which could meet the demand of routine analysis and TCM quality control.

Analysis of residual crosslinking agent content in UV cross-linked poly(ethylene oxide) hydrogels for dermatological application by gas chromatography

Acrylates have been widely used in the synthesis of pharmaceutical polymers. The quantitation of residual acrylate monomers is vital as they are strong irritants and allergens, but after polymerization, are relatively inert, causing no irritation and allergies. Poly(ethylene oxide)(PEO) hydrogels were prepared using pentaerythritol tetra-acrylate(PETRA) as UV crosslinking agent. A simple, accurate, and robust quantitation method was developed based on gas chromatographic techniques(GC), which is suitable for routine analysis of residual PETRA monomers in these hydrogels. Unreacted PETRA was initially identified using gas chromatography–mass spectrometry(GC–MS). The quantitation of analyte was performed and validated using gas chromatography equipped with a flame ionization detector(GC–FID). A linear relationship was obtained over the range of 0.0002%–0.0450%(m/m) with a correlation coefficient(r2)greater than 0.99. The recovery( 4 90%), intra-day precision(%RSD o 0.67), inter-day precision(%RSD o2.5%), and robustness(%RSD o1.62%) of the method were within the acceptable values. The limit of detection(LOD) and limit of quantitation(LOQ) were 0.0001%(m/m) and 0.0002%(m/m), respectively.This assay provides a simple and quick way of screening for residual acrylate monomer in hydrogels.

Separation and Purification of Acetophenones from Cynanchum bengei Decne Root Bark by Combination of Silica Gel and High-speed Counter-current Chromatography

[Objectives] To develop a method for separation and purification of acetophenones from Cynanchum bengei Decne root bark by combination of silica gel and high-speed counter-current chromatography( HSCCC). [Methods]The crude extract of Cynanchum bengei Decne root bark was separated by silica gel column chromatography,and parts A and B containing acetophenones were obtained. Then,parts A and B were separated by HSCCC with a two-phase solvent system composed of petroleum ether-ethyl acetate-methanol-water( 4∶ 6∶ 4. 5∶ 5. 5 and4∶ 6 ∶ 3 ∶ 7, V/V), respectively. [Results] From 260 mg of part A, four compounds with p-dihydroxybenzene 3. 9 mg(Ⅰ),4-hydroxyacetophenone 17. 1 mg( Ⅱ),2,5-di-hydroxyacetophenone 13. 3 mg(Ⅲ) and 2,4-dihydroxyaceto-phenone 21. 0 mg(Ⅳ) were obtained. And from 300 mg of part B,136 mg of Radix Cynanchi Bungei benzophenone(Ⅴ) was obtained. The purity of compounds determined by HPLC was 97. 0%,96. 6%,99. 2%,99. 7%,99. 5%,respectively. [Conclusions] The established method is simple and efficient. It can be used for separation of acetophenones from Cynanchum bengei Decne root bark and has better practical value,which could provide a reference basis for development and utilization of Cynanchum bengei Decne root bark.

Molecular weight determination of a newly synthesized guanidinylated disulfide-containing poly(amido amine) by gel permeation chromatography

A cationic gene delivery vector, guanidinylated disulfide-containing poly(amido amine)(CARCBA), was synthesized by Michael addition reaction between N,N′-cystaminebisacrylamide(CBA) and guanidine hydrochloride(CAR). Gel permeation chromatography(GPC) was used to evaluate the molecular weight of synthesized CAR-CBA. Polyethyleneimine(PEI) with molecular weight of 25 kDa was adopted as a reference, and polyethylene glycols(PEG) with different molecular weights were used to establish a standard curve for determining the molecular weight of CAR-CBA. The effects of two critical factors, namely columns and eluents,on the molecular weight measurement of CAR-CBA were investigated to optimize the GPC quantitative method. The results showed that Ultrahydrogel columns(120, 250) and HAc–NaAc(0.5 M, pH 4.5) buffer solution were the optimal column and GPC eluent, respectively.The molecular weight of the synthesized CAR-CBA was analyzed by the optimized GPC method and determined to be 24.66 kDa.

Separation and purification of deoxynivalenol(DON) mycotoxin from wheat culture using a simple two-step silica gel column chromatography

Deoxynivalenol（DON） is a type B trichothecenes mycotoxin produced by several Fusarium species, often found in foodstuffs for humans and animals. DON is in great demand for the toxicological researches both in vivo and in vitro. In this work, wheat culture was inoculated with a Fusarium graminearum PH-1 strain for DON production. The solvent system for crude extraction was acetonitrile-water（84：16, v/v）. A simple two-step silica gel column chromatography was employed to separate the DON mycotoxin from wheat culture, combined with preparative high performance liquid chromatography（preparative HPLC） to purify the compound. The solvent system for the second silica gel column chromatography was methylene chloride-methanol（17：1, v/v）, which provided a good elution effect selected on thin layer chromatography（TLC）. The target compound was identified by HPLC, and the chemical structure was confirmed by mass spectrometry（MS） and ~1H and ^（13）C nuclear magnetic resonance（NMR） spectroscopy. A total of 433 mg of purified DON was obtained from 1 kg of wheat culture, with a purity of 99.01%. The study had provided an easy-operating and cost-effective method to isolate an expensive compound in a simple way.

Determination of Residual Acrylamide in Medical Polyacrylamide Hydrogel by High Performance Liquid Chromatography tandem Mass Spectroscopy

Objective To determine residual acrylamide in medical polyacrylamide hydrogel by high performance liquid chromatography tandem mass spectroscopy （HPLC-MS）. Methods After 13C3 labeled acrylamide was added, the sample was extracted with water and then cleaned up with ExtrelutTM 20. The polyacrylamide hydrogel sample and 20 clinical cases were analyzed by HPLC-MS/MS and isotope dilution quantifying technique in selected reaction monitoring （SRM） mode. Results Acrylamide was separated from polyacrylamide hydrogel. The concentration of acrylamide in polyacrylamide hydrogel ranged from 3.9×10^-9 to 3.1×10^- 8g/L in the 20 clinical cases. The peak area was favorable linear and the range was up to 3 000 μg/L. The recovery rate was 103.1% with a relative standard deviation （RSD） of 6.20%, when the mark level was 50 lag/L. Conelusion HPLC-MS is a rapid, accurate, and sensitive method for the determination of residual acrylamide in medical polyacrylamide hydrogel.

Rapid,simple and stability-indicating determination of polyhexamethylene biguanide in liquid and gel-like dosage forms by liquid chromatography with diode-array detection

A rapid and simple method for the determination of potyhexamethylene biguanide （polyhexanide, PHMB） in liquid and gel-like pharmaceutical formulations by means of high performance liquid chromatography coupled to diode-array detection （HPLC DAD） was devel- oped. Best separation was achieved using a cyanopropyl bonded phase （Agilent Zorbax Eclipse XDB-CN column 4.6mm x 75 mm with particle size of 3.5 μm） as well as gradient elution consisting of acetonitrile/deionized water at a flow rate of 1.0 mL/min. The optimized and applied chromatographic conditions permitted separation of polyhexanide from interacting raatrix with subsequent detection at a wavelength of 235 nm with good sensitivity. The method validation was carried out with regard to the guidelines for analytical procedures demanded by the International Conference on Harmonisation （ICH）. Mean recoveries of 102% and 101% for gel-like as well as liquid preparations were obtained. Suitable repeatability as well as intermediate precision could bc achieved with limits of detection ≤0.004 mg/mL for both formulations, equivalent to ≤0.004% PHMB concerning sample preparation. Determination of PHMB was accomplished without tedious sample preparation. Interacting matrix could be eliminated by the chromatographicprocedure with excellent performance of system suitability. All analytical requirements were fulfilled permitting a reliable and precise determination of PHMB in pharmaceuticals. Further- more, the developed method was applied to stability testing of pharmaceutical preparations containing PHMB.

Determination of Speciation of Magnesium（Ⅱ） in Albumen by Gel Permeation Chromatography

A gel permeation chromatographic method using cross-linked dextran G-50 was employed to determine the speciation of magnesium(Ⅱ) in albumen. It has been found that 0.22% of magnesium(Ⅱ) in albumen combines with proteins and the rest exists as free ions and small-molecular complexes.

Determination of Steroid Hormone Residues in Fish Tissues Using Gel Permeation Chromatography and Ultra Performance Liquid Chromatography-Tandem Mass Spectrometry

A highly sensitive method was developed for the simultaneous determination of 8 steroid hormones in high-fat fish tissues using ultra high performance liquid chromatography-tandem mass spectrometry(UPLC-MS/MS).The 8 steroid hormones were extracted from the tissues with diethyl ether.Differing from other common purification methods,the extract solutions were cleaned by gel permeation chromatography(GPC) using ethyl acetate-cyclohexane solution(1:1,v/v) as the mobile phase.The separation of target compounds was carried out by a BEH C18 column and a gradient elution consisting of acetonitrile and 0.2% aqueous formic acid(v/v).The compounds were detected under the multiple reaction monitoring(MRM) mode and quantified with external standard method.This method was validated with respect to linearity,specificity,accuracy and precision.A linearity with correlation coefficient larger than 0.995 was achieved in the range of 0.5 to 50 ng m L^(-1).The average recoveries at the spiked levels of 1.0,5.0,and 10.0 μg kg^(–1) varied between 81.7% and 90.8%,with the relative standard deviations(n=5) ranged from 3.50% to 10.0%.The limit of quantification(LOQ) for 8 steroid hormones ranged from 0.2 to 1.5 μg kg^(-1).It was concluded that this method can be successfully applied for the determination of 8 steroid hormones in complicated matrices including high-fat fish tissues.

Alleviation of the plastic deformation of gel ink under strong stress through an esterification of xanthan gum reinforcing its double helix structure

As a natural organic polymer,xanthan gum(XG)can alleviate the plastic deformation of gel ink under strong stress and realize the reasonable regulation of the rheological properties of gel ink.However,as the double-helix structure connected by hydrogen bonds cannot resist the mechanical environment of strong stress,XG shows poor shear resistance.In this study,a polymer gel with interpenetrating polymer network structure was prepared by esterifying XG,taking polystyrene maleic anhydride(SMA)as the modifier.In addition to retaining the excellent rheological properties of XG,the generated polymer gel also exhibited high shear resistance.The optimal addition amount of the esterification reaction modifier was determined as mXG:mSMA=5:3 according to the gel ink standard.With this amount,the viscosity of the modified xanthan gum(SXG)gel increased to 1578.8 mPa·s and 100.7 mPa·s at shear rates of 4 s1 and 383 s1,respectively,and the shear resistance increased more than 2 times compared to the unmodified one.It is because of the ester bond formed by esterification that the reaction strengthens the interaction between molecular segments,enabling the new gel to resist to strong mechanical stress.The new polymer gel studied in this paper and the proposed mechanism of action provide new insights for the development of high-end gel ink and also provide theoretical support for the study of rheological properties of non-Newtonian fluids.

A Gel-Based Solidification Technology for Large Fracture Plugging

Fault fractures usually have large openings and considerable extension. Accordingly, cross-linked gel materials aregenerally considered more suitable plugging agents than water-based gels because the latter often undergo contaminationvia formation water, which prevents them from being effective over long times. Hence, in this study, aset of oil-based composite gels based on waste grease and epoxy resin has been developed. These materials havebeen observed to possess high compressive strength and resistance to the aforementioned contamination, therebyleading to notable increase in plugging success rate. The compressive strength, thickening time, and resistance toformation water pollution of these gels have been evaluated indoors. The results show that the compressivestrength of the gel can reach 11 MPa;additionally, the related gelation time can be controlled to be more than3 h, thereby providing a safe construction time;Invasion of formation water has a small effect on the gel strengthand does not shorten the thickening time. All considered performance indicators of the oil-based gel confirm itssuitability as a plugging agent for fault fractures.

A novel profile modification HPF-Co gel satisfied with fractured low permeability reservoirs in high temperature and high salinity

Conformance control and water plugging are a widely used EOR method in mature oilfields.However,majority of conformance control and water plugging agents are unavoidable dehydrated situation in high-temperature and high-salinity low permeability reservoirs.Consequently,a novel conformance control system HPF-Co gel,based on high-temperature stabilizer(CoCl_(2)·H_(2)O,CCH)is developed.The HPF-Co bulk gel has better performances with high temperature(120℃)and high salinity(1×10^(5)mg/L).According to Sydansk coding system,the gel strength of HPF-Co with CCH is increased to code G.The dehydration rate of HPF-Co gel is 32.0%after aging for 150 d at 120℃,showing excellent thermal stability.The rheological properties of HPF gel and HPF-Co gel are also studied.The results show that the storage modulus(G′)of HPF-Co gel is always greater than that of HPF gel.The effect of CCH on the microstructure of the gel is studied.The results show that the HPF-Co gel with CCH has a denser gel network,and the diameter of the three-dimensional network skeleton is 1.5-3.5μm.After 90 d of aging,HPF-Co gel still has a good three-dimensional structure.Infrared spectroscopy results show that CCH forms coordination bonds with N and O atoms in the gel amide group,which can suppress the vibration of cross-linked sites and improve the stability at high temperature.Fractured core plugging test determines the optimized polymer gel injection strategy and injection velocity with HPF-Co bulk gel system,plugging rate exceeding 98%.Moreover,the results of subsequent waterflooding recovery can be improved by 17%.

The Development of Gel Media and Columns for Large-Scale Chromatography of Proteins, a Historical Review

The first dedicated protein chromatography media were introduced during the 1950s and 1960s. There was an early awareness of the possibility of using these for production applications within the biopharmaceutical industry. However, the crucial limitation was the fact that those media that were most compatible with proteins lent themselves less favourably to scaling-up. The problems were primarily physical. Thus the fibrous cellulose media showed bed cracking tendencies and the bead shaped polyacrylamide, dextran, and agarose gel media, then available, were too soft to stand the hydrodynamic forces acting in large columns, leading to bed compaction and increased pressure drop. At the time, the best solution to the latter problem, after a number of intermediary solutions were tried, was the introduction of the stacked column concept in which several short column segments were connected by small bore tubing, thus reducing the force acting on the particles in each bed copartment. However, the ultimate remedy, the introduction of chromatographic matrices that combine the desired features of adequate rigidity, macroporosity, biocompatibility, chemical stability (for CIP and SIP) and derivatizability, did not occur until the middle of the 1980s when adquately cross-linked agarose gel media such as Sepharose Fast Flow were made available. The paper also recognizes the many attempts made during the past 50 years to develop continous chromatography columns. Most of the designs are based on an annular bed or on an array of anularly arranged parallel columns continuously fed with samples in a cyclic manner. The introduction of media and columns for expanded bed adsorption followed a demand for fewer purification steps and shorter process times. In recent years, columns have been introduced that allow packing and repacking without needing to open the column. The review provides an historical account of the developments that have led to the present state-of-the-art both regarding large diameter columns and gel media intended for industrial applications of protein chromatography and also discusses the current trends that point to possible future applications.

Determination of constituents of essential oil from Angelica sinensis by gas chromatographymass spectrometry

Gas chromatographymass spectrometry (GC-MS) coupled with chemometric resolution upon two- dimensional data was employed to analyze the constituents of essential oils of Angelica sinensis. Constituents in essential oils of Angelica sinensis root were identified by GC-MS with the help of subwindow factor analysis (SFA) method resolving two-dimensional original data into mass spectra and chromatograms. 76 of 97 separated constituents in essential oil of Angelica sinensis root were identified and quantified, and they account for about 91.36% of the total content. The results show that ligustilide, butylene phthalide, 2-methoxy-4-vinylphenol, carvacrol, allo-ocimene,2,6,6-trimethylbicyclo-[3,1,1]hept-2-ene are the main constituents in essential oil of Angelica sinensis root.

Comparison in vitro permeation of curcumin from topical gels by liquid chromatography tandem mass spectrometry

Objective: To find a more effective method of topical transdermal delivery of curcumin. Methods: We prepared curcumin carbopol(CRB) 974P and hydroxypropylcellulose(HPC) gel formulations containing menthol or Azone as permeation enhancers. In this study, negative mode electrospray ionization and a triple quadruple LC/MS/MS instrument operated in multiple reaction mode was used for curcumin detection. The assay was linear over a concentration range of 10 ng/mL to 400 ng/mL for curcumin(average R2= 0.997 2). Excised nude mouse dorsal side skin was used in an in vitro skin permeation study performed using the method of Franz. Results: Our results showed that all of the topical gel formulations we developed were free from skin irritation. The percutaneous flux and enhancement ratio of curcumin across nude mouse epidermis were enhanced markedly by the addition of menthol or Azone to both types of gel formulations. We found that the HPC gels containing quantities of Azone showed an enhanced permeation effect as compared to gels containing menthol. In the case of HPC gels containing Azone, the increase in permeability was significant(P<0.05) as compared to the gels containing menthol. Conclusion: Azone shows a significantly more remarkable permeation effect than menthol. As such, this novel delivery strategy offers significant promise and is worthy of further exploration in attempts to enhance the medicinal application of curcumin.

Separation of Recombinant Geranylgeranyl Diphosphate Synthase of Deinococcus radiodurans from Expressed Strain Cell Homogenate by Immobilized Metal Affinity Chromatography on a Characterized Monolithic Cryogel Column

Geranylgeranyl diphosphate synthase (GGPPS) plays a key role in the biosynthesis of antioxidative ca-rotenoid from the extremely radioresistant bacterium Deinococcus radiodurans. In this work, the recombinant GGPPS expressed in Escherichia coli by cloning and transforming the gene dr1395 of D. radiodurans was isolated rapidly by an immobilized metal affinity supermacroporous cryogel, i.e., Cu2+-iminodiacetic acid (IDA)-cryogel. The properties of the Cu2+-IDA-cryogel were characterized using capillary-based mathematical model and experi-mental measurements. The obtained protein samples were analyzed by the sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE). The porosity of the present Cu2+-IDA-cryogel is 90.4% and the water permeabil-ity is 5.04×10-12 m2. From the capillary-based model, this cryogel presents a slightly wide normal pore (capillary) size distribution with the mean diameter of 55.2 μm, the standard deviation of 28.0 μm and the half of skeleton wall thickness of 2.8 μm. The pore size distribute from about 10 to 141 μm and the effective tortuosity of these capillary pores increases from 2.60 to 9.05. The isolation of the GGPPS from cell homogenate can be achieved at the flow velocity of 3.40×10-4 m·s-1 by the Cu2+-IDA-cryogel bed. High-purity GGPPS (about 91.4%) is obtained according to the SDS-PAGE analysis of the elution samples, indicating that the present method is a promising, simple and ef-fective approach to isolate GGPPS from cell homogenate of engineering strains.

Activation of endogenous neurogenesis and angiogenesis by basic fibroblast growth factor-chitosan gel in an adult rat model of ischemic stroke

Attempts have been made to use cell transplantation and biomaterials to promote cell proliferation,differentiation,migration,and survival,as well as angiogenesis,in the context of brain injury.However,whether bioactive materials can repair the damage caused by ischemic stroke by activating endogenous neurogenesis and angiogenesis is still unknown.In this study,we applied chitosan gel loaded with basic fibroblast growth factor to the stroke cavity 7 days after ischemic stroke in rats.The gel slowly released basic fibroblast growth factor,which improved the local microenvironment,activated endogenous neural stem/progenitor cells,and recruited these cells to migrate toward the penumbra and stroke cavity and subsequently differentiate into neurons,while enhancing angiogenesis in the penumbra and stroke cavity and ultimately leading to partial functional recovery.This study revealed the mechanism by which bioactive materials repair ischemic strokes,thus providing a new strategy for the clinical application of bioactive materials in the treatment of ischemic stroke.

Trend of Developing Aqueous Liquid and Gel Electrolytes for Sustainable,Safe,and High‑Performance Li‑Ion Batteries

Current lithium-ion batteries(LIBs)rely on organic liquid electrolytes that pose significant risks due to their flammability and toxicity.The potential for environmental pollution and explosions resulting from battery damage or fracture is a critical concern.Water-based(aqueous)electrolytes have been receiving attention as an alternative to organic electrolytes.However,a narrow electrochemicalstability window,water decomposition,and the consequent low battery operating voltage and energy density hinder the practical use of aqueous electrolytes.Therefore,developing novel aqueous electrolytes for sustainable,safe,high-performance LIBs remains challenging.This Review first commences by summarizing the roles and requirements of electrolytes–separators and then delineates the progression of aqueous electrolytes for LIBs,encompassing aqueous liquid and gel electrolyte development trends along with detailed principles of the electrolytes.These aqueous electrolytes are progressed based on strategies using superconcentrated salts,concentrated diluents,polymer additives,polymer networks,and artificial passivation layers,which are used for suppressing water decomposition and widening the electrochemical stability window of water of the electrolytes.In addition,this Review discusses potential strategies for the implementation of aqueous Li-metal batteries with improved electrolyte–electrode interfaces.A comprehensive understanding of each strategy in the aqueous system will assist in the design of an aqueous electrolyte and the development of sustainable and safe high-performance batteries.