Bending and free vibrational analysis of bi-directional functionally graded beams with circular cross-section

The bending and free vibrational behaviors of functionally graded(FG)cylindrical beams with radially and axially varying material inhomogeneities are investigated.Based on a high-order cylindrical beam model,where the shear deformation and rotary inertia are both considered,the two coupled governing differential motion equations for the deflection and rotation are established.The analytical bending solutions for various boundary conditions are derived.In the vibrational analysis of FG cylindrical beams,the two governing equations are firstly changed to a single equation by means of an auxiliary function,and then the vibration mode is expanded into shifted Chebyshev polynomials.Numerical examples are given to investigate the effects of the material gradient indices on the deflections,the stress distributions,and the eigenfrequencies of the cylindrical beams,respectively.By comparing the obtained numerical results with those obtained by the three-dimensional(3D)elasticity theory and the Timoshenko beam theory,the effectiveness of the present approach is verified.

HYBRID PERTURBATION-GALERKIN SOLUTION OF THE FLOW IN A CIRCULAR CROSS-SECTION TUBE WITH CONSTRICTION

Using hybrid perturbatin_Galerkin technique,a crcular cross_section tube model with sinusoidal wall is studied.This technique can remove the limitation of small parameters for perturbation and the difficulty of selecting good coordinate functions about Galerkin technique.The effects caused by the boundary conditions and the Reynolds number on the flow were discussed.The position of the separate and reattachment points was obtained.The tendency of the variation about the shear stress on the wall and friction factor along the axis direction were also analyzed.The results at a small parameter have good agreements with the perturbation ones.

THE APPROXIMATE ANALYTICAL SOLUTION FOR THE BUCKLING LOADS OF A THIN-WALLED BOX COLUMN WITH VARIABLE CROSS-SECTION

For a thin-walled box column with variable cross-section, the three governing equations for torsional-flexural buckling are ordinary differential equations of the second or fourth order with variable coefficients, so it is very difficult to solve them by means of an analytic method. In this paper, polynomials are used to approximate the geometric properties of cross-section and certain coefficients of the differential equations. Based on the energy principle and the Galerkin's method, the approximate formulas for calculating the flexural and torsional buckling loads of this kind of columns are developed respectively, and numerical examples are used to verify the correctness of the solutions obtained. The results calculated in this paper provide the basis for demonstrating the stability of thin-walled box columns with variable cross-section. This paper is of practical value.

Ultimate flexural strength of normal section of FRP-confined RC circular columns

Numerical analysis is carried out to study the sectional properties of the fiber-reinforced polymer（FRP）-confined reinforced concrete（RC）circular columns. The axial load ratio, the FRP confinement ratio and the longitudinal reinforcement characteristic value are the three main parameters that can influence the neutral axis depth when concrete compression strain reaches an ultimate value. The formula for computing the central angle θ, corresponding to the compression zone, is established according to the data regression of the numerical analysis results. The numerical analysis results demonstrate that the concrete stress enhancement from transverse confinement and strain hardening of the longitudinal reinforcement can cause a much greater flexural strength than that defined by the design code. Based on the analytical studies and the test results of 36 large scale columns, the formula to calculate the flexural strength when columns fail under seismic loading is proposed, and the calculated results agree well with the test results. Finally, parametric studies are conducted on a typical column with different axial load ratios, longitudinal reinforcement characteristic value and FRP confinement ratios. Analysis of the results shows that the calculated flexural strength can be increased by 50% compared to that of unconfined columns defined by the code.

Torsionally Coupled Response Control of Offshore Platform Structures Using Circular Tuned Liquid Column Dampers

In this paper, the control performance is investigated of Circular Tuned Liquid Column Dampers (CTLCD) over torsional response of offshore platform structures excited by ground motions. Based on the equation of motion for the CTLCD-structure system, the optimal control parameters of CTLCD are given through some derivations on the supposition that the ground motion is a stochastic process. The influence of systematic parameters on the equivalent damping ratio of the structures is analyzed with purely torsional vibration and translational-torsional coupled vibration, respectively. The results show that the Circular Tuned Liquid Column Damper (CTLCD) is an effective torsional response control device.

Experimental study on seismic behavior of circular RC columns strengthened with pre-stressed FRP strips

Bonding fiber reinforced polymer （FRP） has been commonly used to improve the seismic behavior of circular reinforced concrete （RC） columns in engineering practice. However, FRP jackets have a significant stress hysteresis effect in this strengthening method, and pre-tensioning the FRP can overcome this problem. This paper presents test results of 25 circular RC columns strengthened with pre-stressed FRP strips under low cyclic loading. The pre-stressing of the FRP strips, types of FRP strips and longitudinal reinforcement, axial load ratio, pre-damage degree and surface treatments of the specimens are considered as the primary factors in the tests. According to the failure modes and hysteresis curves of the specimens, these factors are analyzed to investigate their effect on bearing capacity, ductility, hysteretic behavior, energy dissipation capacity and other important seismic behaviors. The results show that the initial lateral confined stress provided by pre-stressed FRP strips can effectively inhibit the emergence and development of diagonal shear cracks, and change the failure modes of specimens from brittle shear failure to bending or bending-shear failure with better ductility. As a result, the bearing capacity, ductility, energy dissipation capacity and deformation capacity of the strengthened specimens are all significantly improved.

Local Tensile Strength of Connection Between H-Steel Beam Flange and Concrete-Filled Circular Column Tube with Through Diaphragm

This paper focused on investigating local tensile strength of connection between steel beam flange and concrete-filled circular column tube with through diaphragm. Three specimens were designed and tested to failure, and the structure behavior was studied by experiment and FEM analysis. On the basis of the results obtained, an estimation for local plastic and ultimate strengths of the connections using yield line theory was attempted, which results in a good prediction.

Experimental Behavior of Recycled Aggregate Concrete Filled Steel Tubular Columns

During the modernization or rehabilitation activity,the demolished structural waste causes large soil pollution and unavailability of natural aggregate is the big concern for the construction industry.Therefore,this manuscript deals with the Composite Steel Circular Column(CSCC)with Recycled Aggregate concrete(RAC)as infill is partly used,with the replacement of 25%and 50%in M30 grade of Concrete.And internal reinforcement steel is fully replaced by rolled steel tubes(circular and square)with varied thickness,ISA-unequal angle.Around 14 specimens are cast and examined under axial load for analysis of the deflection characteristics,the load-bearing capacity along with its buckling behavior.The experimental values are estimated through LVDT(linear variable differential transducer)at 3-phase.The curve of load-deflection is drawn with the load pattern.From the date interpretation,it is found column made of 50%-RAC has more than 25%-RAC.

局部锈蚀圆钢管混凝土短柱轴压承载力试验研究

钢管混凝土(CFST)在服役环境中被腐蚀,导致其钢结构承载力降低,严重威胁到结构的服役性能和使用寿命。首先,采用机加工车铣方法制作模拟局部锈蚀的人工缺陷,然后以钢管外表面局部环向贯通锈蚀位置、锈蚀钢管体积损失率、锈蚀外表面面积损失率(简称锈蚀面积损失率,下同)为试验参数,对45根局部锈蚀圆CFST短柱试件进行轴压承载力试验;其次,分析锈蚀位置、锈蚀钢管体积损失率、面积损失率和壁厚损失率对锈蚀试件承载力、刚度和延性的影响,揭示锈蚀CFST试件破坏机理和承载力退化机制;最后,针对局部锈蚀圆CFST短柱构件轴压承载力提出一个简化实用计算公式。研究结果表明:各试件具有类似的破坏特征,主要呈明显的腰鼓状破坏,且发生在锈蚀区;随着锈蚀钢管体积损失率增大,锈蚀CFST柱的承载力、刚度和延性均出现不同程度的降低;在锈蚀钢管体积损失率和面积损失率相同的情况下,就局部锈蚀位置影响而言,中部影响最大;就锈蚀程度表征参数影响而言,锈蚀钢管体积损失率影响最大,面积损失率次之,壁厚损失率最小;本文提出的简化实用公式可为圆钢管混凝土构件全寿命设计提供参考依据。

内置工字型CFRP型材高强圆钢管高强混凝土轴压短柱组合效应分析

目的 研究内置工字型CFRP型材的高强圆钢管高强混凝土短柱在轴心压力作用下三种材料的组合效应。方法 采用有限元分析软件ABAQUS对其进行数值模拟,通过相关试验验证模型的准确性,并对典型构件的破坏形态、受力全过程曲线进行分析,揭示构件各组成部分之间的相互作用和工作机理,评估CFRP配置率、钢材屈服强度、混凝土抗压强度、约束效应系数对组合效应的影响。结果 在高强圆钢管高强混凝土柱中内置CFRP型材,对构件的延性及安全裕度有显著提高,并改善了高强圆钢管对高强混凝土的约束,提高了构件的组合效应。结论 CFRP配置率控制在5.9%~8.4%,约束效应系数在1.2~1.4,钢材屈服强度不大于770 MPa时,构件中三种材料组合效应最佳。

圆形基坑极正交各向异性支护结构变形解析分析

考虑圆形深基坑支护结构轴向和环向配筋的差异,将支护结构简化为极正交各向异性圆柱薄壳,研究了分层土体中具有弹性支撑环梁约束的支护结构轴对称变形和内力特征.首先,将弹性支撑环梁的约束解除,代之以沿环向分布的未知集中力,基于弹性环梁和圆柱壳的边界条件和变形协调条件,得到了分层土体中具有弹性支撑环梁支护结构轴对称变形的解析解.其次,以上海地区某一圆形深基坑支护结构为例,揭示了支护结构环向和纵向弹性模量、环梁刚度、土体重度和静止土压力系数等因素对支护结构内力和变形的影响,结果表明:支护结构以环向承压为主,轴向弯曲为辅,故其环向刚度对径向位移的影响要明显大于其轴向刚度的影响,但材料参数对内力分布影响较弱;环梁刚度的增加可有效限制支护结构的变形,但会引起支护结构在支撑环梁处内力的显著增大;土层性质相差不大区域的支护结构可按均质土中支护结构进行分析,而土层性质有较大突变区域的支护结构分析则需考虑土层的分层效应.

外剥内扎术加内痔柱状缝扎悬吊联合痔科生肌散治疗环状混合痔的临床研究

目的探究外剥内扎术加内痔柱状缝扎悬吊联合痔科生肌散治疗环状混合痔的临床效果和安全性。方法选取2021年1月至2022年8月江苏省无锡市中医院收治的90例环状混合痔患者,采用随机数字表法将其分为对照组(外剥内扎术加内痔柱状缝扎悬吊治疗)和试验组(外剥内扎术加内痔柱状缝扎悬吊联合痔科生肌散治疗),各45例。治疗后1、3、7 d,比较两组肛周疼痛和水肿评分,比较两组治疗前及治疗后2周肛门狭窄情况、血清炎症因子水平,记录两组不良反应发生情况。结果治疗后3、7 d,两组肛周疼痛和水肿评分均低于治疗后1 d,治疗后7 d低于治疗后3 d,试验组治疗后1、3、7 d肛周疼痛和水肿评分低于同期对照组(P<0.05)。试验组肛门狭窄率低于对照组(P<0.05)。治疗后2周,两组肛门功能评分高于治疗前,且试验组高于对照组(P<0.05)。治疗后2周,两组白细胞计数、血清降钙素原水平均低于治疗前,且试验组低于对照组(P<0.05)。试验组不良反应总发生率低于对照组(P<0.05)。结论外剥内扎术加内痔柱状缝扎悬吊联合痔科生肌散治疗环状混合痔的临床效果较好,可在临床上推广使用。

FRP约束UHPC圆形短柱轴心受压性能研究

为研究纤维增强复合材料(FRP)种类、FRP层数和钢纤维体积掺量对超高性能混凝土(UHPC)圆形短柱轴压性能的影响,对21个FRP约束UHPC圆形短柱进行轴心受压试验,分析试件的失效破坏特征及受力机理,研究各参数对试件极限强度和极限应变的影响规律.研究结果表明:FRP层数的增加可以提高UHPC圆形短柱的极限强度,试件C12、C22、C32的极限强度比C11、C21、C31分别提高了17.8%、25.4%、23.4%;钢纤维体积掺量的增加可以使UHPC圆形短柱的极限强度和极限应变得到提高,并可以在一定程度上改善试件的脆性,试件C31的极限强度和极限应变比试件C21分别提高了2.9%和15.1%,比试件C11分别提高了4.7%和50%;在FRP层数和钢纤维体积掺量相同的情况下,碳纤维增强复合材料(CFRP)对圆形短柱极限强度的改善程度明显优于玻璃纤维增强复合材料(GFRP),试件C11、C12和C13的极限强度比试件G11、G12和G13的分别提高了9.7%、7.8%和7.2%;考虑钢纤维的约束影响,提出FRP约束UHPC圆形短柱的抗压强度和极限应变的计算模型,并进一步给出FRP约束UHPC的本构模型.

圆钢管型钢再生混凝土组合柱滞回性能非线性有限元分析

基于圆钢管型钢再生混凝土组合柱低周反复荷载试验研究,采用OpenSees软件对该组合柱进行了滞回性能数值分析,获取了组合柱的滞回曲线及抗震性能指标,并与试验结果进行了比较,验证了组合柱数值模型的合理性。在此基础上,对组合柱的滞回性能开展了参数影响分析。结果表明:再生骨料取代率从0增大到100%,组合柱的峰值荷载下降了7.78%,延性略有降低;提高再生混凝土强度、型钢强度及圆钢管强度,对于提升组合柱的承载力及刚度是有利的,但却使组合柱的脆性增大;随着轴压比的增大,组合柱的承载力呈现先上升后下降的趋势,而延性逐渐变差;型钢配钢率从5.54%增至9.99%,组合柱的峰值荷载提高了24.34%,但对于改善组合柱的延性不明显;增大钢管壁厚对组合柱的承载力和延性均是有利的。

圆钢管砖骨料地聚物再生混凝土柱滞回性能试验研究

为探究废弃黏土砖再利用的可行性,对6根圆钢管砖骨料地聚物再生混凝土柱的滞回性能进行了系列试验研究。以不同钢管厚度(4、6 mm)、砖骨料取代率(0%、50%、100%)、轴压比(0.05、0.25、0.50)为参数,得到了试件在往复荷载作下的失效模态、骨架曲线和滞回曲线,并对构件的刚度退化、滞回性能、峰值承载力、延性、承载力退化和耗能能力等抗震性能指标的变化规律分析。结果表明:试件的失效模式表现为底部发生鼓曲、开裂,出现塑性铰的区域核心混凝土破碎,与普通钢管混凝土相似;砖骨料取代率和轴压比的增加会降低试件的承载力,钢管厚度的增加会提高试件的承载力。试件的滞回曲线饱满,表现出不明显的捏缩,表明耗能能力较好;轴压比的增加导致试件的变形能力降低,加快了刚度和承载力的退化速度,增长钢管厚度可以提高试件的变形能力;砖骨料取代率对试件刚度退化、延性、承载能力和耗能能力的影响有限。

反复荷载下圆钢管型钢再生混凝土组合柱耗能能力及延性分析

对11个圆钢管型钢再生混凝土组合柱试件进行了低周反复荷载试验,观察了组合柱的破坏形态及特征,获取了组合柱的滞回曲线、等效粘滞阻尼系数、延性系数及侧向位移角等性能指标,分析了再生粗骨料取代率、型钢截面形式、轴压比、型钢配钢率和圆钢管径厚比等参数对组合柱耗能能力及延性的影响规律。结果表明:反复荷载作用下组合柱呈压弯塑性铰破坏模式;组合柱的荷载-位移滞回曲线饱满呈纺梭形,屈服位移后的等效粘滞阻尼系数在0.30~0.48之间,平均位移延性系数大于3.0,极限侧向位移角介于1/30~1/20之间且均大于规范限值1/50,组合柱表现出良好的耗能能力和延性。此外,组合柱的耗能能力和延性受再生粗骨料取代率的影响较大,全再生混凝土较普通混凝土耗能能力下降14.5%;增加钢管壁厚或型钢配钢率有利于提升组合柱的耗能能力和延性,而增大轴压比则对组合柱的延性和变形不利;内置型钢采用箱型截面时,组合柱耗能及延性最优,与工字型钢相比,采用箱型截面型钢的组合柱耗能能力和延性分别提升了23.5%和51.9%。

预应力薄壁圆钢管约束混凝土短柱轴压性能初探

为提高薄壁钢管混凝土柱轴心受压性能,提出了预应力薄壁圆钢管约束混凝土柱,即采用对拉螺栓对薄壁圆钢管施加环向预应力,形成对内部混凝土初始约束围压,以提高内部混凝土的轴心抗压强度及承载力性能。为探究其轴向受压性能提升效果,进行了预应力薄壁圆钢管约束混凝土短柱轴心受压试验;并采用ABAQUS有限元计算软件建立了相应的非线性有限元数值模型,基于试验所获得荷载-位移数据,验证了模型的可靠性。在合理可靠试验模型的基础上,进行了不同预应力度(k=0、0.1、0.2、0.3、0.4和0.5)和不同钢管厚度(t=1.5mm、2.0mm、2.5mm和3.0mm)情况下的轴心受压性能影响分析。结果表明:采用对拉螺栓对薄壁圆钢管混凝土柱施加环向预应力,可有效提高其轴心抗压强度、刚度和延性;在合适预应力范围内,预应力度(k=0~0.4)越大,预应力薄壁钢约束混凝土短柱轴心受压性能提升越明显;但较大的预应力度(k=0.5)会让构件在达到峰值荷载后,其承载力降低较为明显,从而使构件延性降低;当预应力度k不变,构件的轴心受压性能随钢管厚度t的增大而增大。

圆钢管型钢再生混凝土组合柱水平承载力计算方法研究

通过对11个圆钢管型钢再生混凝土组合柱进行低周反复荷载试验,分析再生粗骨料取代率、型钢截面形式、轴压比、型钢配钢率及圆钢管壁厚参数对组合柱水平承载力的影响规律;观察了组合柱的破坏形态及特征,研究了圆钢管、型钢翼缘及腹板应变的发展规律,分析了组合柱的地震破坏特征。研究表明,在水平地震作用下组合柱发生典型的压弯塑性铰破坏。在此基础上,结合现有规范提出了基于叠加原理的圆钢管型钢再生混凝土组合柱水平承载力计算方法。计算结果表明,其水平承载力计算值与试验值吻合度较好,能较为准确地预测组合柱的水平承载力。

新型开洞圆钢管混凝土柱-混凝土梁连接节点受力性能研究

传统的钢-混凝土混合结构的圆钢管混凝土柱-混凝土梁连接节点存在钢筋交错、纵横向需与钢构件避让或开孔等情况,节点构造复杂,施工难度较大,连接节点成为钢-混凝土混合结构的设计及施工难点。对此提出了新型开洞圆钢管混凝土柱-混凝土梁连接节点,并结合近年来采用钢-混凝土混合结构的项目经验,对该类节点进行有限元分析,研究了柱顶轴压力和柱端水平力对节点各部分构件受力性能的影响,结果表明,柱顶轴压力的变化显著影响了圆钢管混凝土柱钢管开洞位置各构件的应力,且偏心力对圆钢管混凝土柱承载力有一定的折减。最后考虑到钢管壁开洞对圆钢管混凝土柱存在一定程度的削弱,采用了四种加强措施,分析了四种加强措施下钢管荷载-应力曲线,结果表明,开洞位置钢管壁加厚效果最为显著,设置内环板对缓解应力集中效应也有一定的效果,设置竖向断开加劲肋与设置竖向连续加劲肋荷载-应力曲线基本一致,考虑到设置竖向断开加劲肋所需钢材更少,认为设置竖向断开加劲肋具有较为显著的优越性。

圆形钢管混凝土柱轴压承载力及承载力组成研究

为了研究相互作用下圆形钢管混凝土(circular concrete-filled steel tube,CCFST)柱中钢管和混凝土各自的承载力贡献,通过ABAQUS软件中的VUMAT子程序导入一种新的混凝土材料本构,建立了能够反映CCFST柱中钢管和混凝土相互作用的三维有限元模型,并通过试验数据验证了模型的荷载-位移曲线、钢管和混凝土的荷载-变形曲线以及侧向变形曲线。在此基础上分析了混凝土强度、钢管屈服强度、径厚比以及套箍系数对CCFST柱承载力及其组成的影响。然后结合有限元模型推导了CCFST柱在轴压荷载下峰值承载力的数学模型,模型中提出的钢管环向应力比例系数和混凝土承载力贡献系数可以评估钢管和混凝土的受力状态。将计算模型与现行规范及现有研究进行对比,发现提出的计算公式具有良好的计算精度,且可以评估钢管和混凝土各自的承载力贡献。