Effects of particle type on the particle fluidization and distribution in a liquid–solid circulating fluidized bed boiler

A liquid-solid circulating fluidized bed boiler is designed and built for visualization research by applying the fluidized bed heat transfer and fouling prevention technology to the water side of the boiler. Four types of engineering plastic particles with different physical properties are selected as the solid working media. The effect of particle types on the fluidization and distribution of particles in the boiler is investigated under different feedwater flow rates and amount of added particles by using the charge couple device image measurement and acquisition system. The results show that all kinds of particles can't be normally fluidized and accumulate in the drum at low amount of added particles and feedwater flow rate. The particles with great density and low sphericity are more likely to accumulate. The average solid holdup in the riser tubes increases with the increase in feedwater flow rate and the amount of added particles. The non-uniform degree of particle distribution in the riser tubes generally decreases with the increase in feedwater flow rate and the amount of added particles. The particles with small density and settling velocity have high average solid holdup in the riser tubes under close sphericity. In generally,the smaller the density and settling velocity, the more uniform the particle distribution in the riser tubes.Three-dimensional diagrams of the non-uniform degree of particle distribution in the riser tubes of the boiler are established.

Compatibility of Fly Ash and Slag from Circulating Fluidized Bed Boiler for Concrete Beam

The applications of fly ash and slag from circulating fluidized bed boiler were studied as mineral admixture and aggregate for steel reinforced concrete beam.The results show that the concrete beam with fly ash and slag from circulating fluidized bed boilers has a similar ultimate cracking load coefficient as the ordinary cement concrete and a higher bending moment limit.Under the same load,it has a smaller deformation than the ordinary concrete.

Model prediction of the operating behavior of a circulating fluidized bed boiler

An improved mathematical model for a circulating fluidized bed (CFB) boiler based on the model developed earlier by the authors was applied to simulate the operation of a 12 MW CFB boiler. The influences of the excess air ratio, primary air ratio, coal particle size distribution, coal properties (ash content and volatile content) and Ca/S ratio on the boiler operation were analyzed. The results showed that the model simulation may be applied to the optimum design and economic operation of the CFB boiler.

Hardening Properties of Foamed Concrete with Circulating Fluidized Bed Boiler Ash, Blast Furnace Slag, and Desulfurization Gypsum as the Binder

Recently, a large amount of circulating fluidized bed boiler ash (CFBA) and desulfurization gypsum (DSG) has been produced, and it is essential to develop technology to utilize them. These materials have CaO and SO3, which are considered to be a stimulant for blast furnace slag (BFS). This study presents an experimental investigation of the compressive strength and heavy metal ions immobilization properties of cement-free materials comprising CFBA, BFS, and DSG. The feasibility of manufacturing foamed concrete using these materials was examined, and field test of foamed concrete was conducted. Experimentally, the flow, compressive strength, and heavy metal ions concentration were evaluated via inductively coupled plasma atomic emission spectroscopy (ICP-AES) of the paste and foamed concrete. The experimental investigation revealed the self-healing hardening ability of fluidized bed boiler ash. In addition, the compressive strength was increased with the increasing replacement rates of BFS and DSG in the CFBA paste, and the compressive strength of 14.6 - 17.2 MPa was recorded over 28 days of curing. From the result obtained, the feasibility of manufacturing foamed concrete with a foam volume of 120 L, incorporating the aforementioned materials, is confirmed. It was also found that after 28 days of age, a 7.9-MPa compressive strength of the foamed concrete was attained, and heavy metal ions elution in this foamed concrete was also significantly reduced. Therefore, CFBA, BFS, and DSG could be used as a binder for the foamed concrete.

Combustion characteristics of low-quality lignite for different bed material sphericities in a circulating fluidized bed boiler:A numerical study

This study delves into the combustion behavior of various lignite types within a circulating fluidized bed boiler(CFBB),with a primary focus on the impact of different bed material sphericity ratios(0.5,0.7,and 0.9).Utilizing bed material with a sphericity ratio of 0.9 sourced from theÇan power plant and verified through experimentation,the research reveals several key findings.Notably,furnace temperatures tended to rise with higher sphericity ratios,albeit with variations between lignite types,particularly highlighting the complexity of this relationship in the case of GLI-Tunçbilek lignite.Pressure levels in the combustion chamber remained consistent across different sphericity ratios,indicating minimal influence on pressure dynamics.Improved combustion efficiency,especially at the bottom of the boiler,was observed at lower sphericity levels(0.5 and 0.7)forÇan lignite,as reflected in CO_(2) mole fractions.While NO_(x) emissions generally decreased with lower sphericity,the sensitivity to sphericity varied by lignite type,with Ilgın lignite showcasing low NO_(x) but high SO_(2) emissions,underscoring the intricate interplay between lignite properties,sphericity,and emissions.Overall,this study advances our understanding of CFBB combustion dynamics,offering insights valuable for optimizing performance and emissions control,particularly in lignite-based power.

Experimental Study on an On-Line Measurement of High Temperature Circulating Ash Flux in a Circulating Fluidized Bed Boiler

A new Kind of measuring method that may be used to measure high temperature circulating solid particles flux in a circulating fluidized bed boiler is studied in this paper. The measuring method is founded on the principle of thermal equilibrium. A series of cold tests and hot tests were carried to optimize the structure and collocation of water-cooling tubes and showed that the method had the advantage of simple, accurate, reliable and good applicability for on-line "usage in a circulating fluidized bed boiler.

New application notion of pipeline transport——integrated in industry solid waste innocuous and efficient disposition

In order to solve transport problems of industry solid,firstly,a new applicationnotion of pipeline transport was presented,that is to say,combining pretreatment andtransport with disposal techniques of industry solid waste.Secondly,the integrated dis-posal and transport system for industry solid waste was introduced,in particular,the oper-ating principles,equipment set-up,key technology and technical parameters.Next,thispaper illustrated the application of this integrated system.Such as it can transport coalsludge with sufficiently high solids content(about 72%～77%)and high apparent viscosity(about 1 000～3 000 Pa.s)directly by pipeline having no use for water and addition agent.Generally,the transport distance is about 1 000 m.This system has been successfullyused in innocuous disposition and efficient utilization of other industrial byproducts or solidwastes,such as city sludge and paper making waste.The integrated system causes nopollution to the environment for its complete seal and realizes protecting the environment,conserving the energy,promoting the development of cycling economic.Finally,the paperdiscussed the research works that were needed for studying such pipeline transport sys-tem and narrates the relevant condition and application status.

A Survey on Intelligent Optimization Approaches to Boiler Combustion Optimization

This paper reviews the researches on boiler combustion optimization,which is an important direction in the field of energy saving and emission reduction.Many methods have been used to deal with boiler combustion optimization,among which evolutionary computing(EC)techniques have recently gained much attention.However,the existing researches are not sufficiently focused and have not been summarized systematically.This has led to slow progress of research on boiler combustion optimization and has obstacles in the application.This paper introduces a comprehensive survey of the works of intelligent optimization algorithms in boiler combustion optimization and summarizes the contributions of different optimization algorithms.Finally,this paper discusses new research challenges and outlines future research directions,which can guide boiler combustion optimization to improve energy efficiency and reduce pollutant emission concentrations.

Extending EMMS-based models to CFB boiler applications

Recently, EMMS-based models are being widely applied in simulations of high-throughput circulating fluidized beds （CFBs） with fine particles. Its use for low flux systems, such as CFB boiler （CFBB）, still remains unexplored. In this work, it has been found that the original definition of cluster diameter in EMMS model is unsuitable for simulations of the CFB boiler with low solids flux. To remedy this, we propose a new model of cluster diameter. The EMMS-based drag model （EMMS/matrix model） with this revised cluster definition is validated through the computational fluid dynamics （CFD） simulation of a CFB boiler.

Static and Transient Performance Prediction for CFB Boilers Using a Bayesian-Gaussian Neural Network

A Bayesian-Gaussian Neural Network (BGNN) is put forward in this paper to predict the static and transient performance of Circulating Fluidized Bed (CFB) boilers. The advantages of this network over Back-Propagation Neural Networks (BPNNs), easier determination of topology, simpler and time saving in training process as well as selforganizing ability, make this network more practical in on-line performance prediction for complicated processes. Simulation shows that this network is comparable to the BPNNs in predicting the performance of CFB boilers. Good and practical on-line performance predictions are essential for operation guide and model predictive control of CFB boiIers, which are under research by the authors.