A cladding-pumping based power-scaled noise-like and dissipative soliton pulse fiber laser

We report a high-average-power noise-like pulse(NLP) and dissipative soliton(DS) pulse fiber laser. Average power as high as 4.8 W could be obtained at the fundamental mode-locked repetition rate. The NLP can also be transformed into a more powerful DS mode-locking state by optimizing the polarization and losses of intra-cavity pulses in the nonlinear polarization evolution regime. The operation mode between the NLP and DS can be switched, and the laser output performance in both modes has been studied. The main advantage of this work is switchable high-power operation between the NLP and DS. In comparison with conventional single-mode NLP fiber lasers, the multi-function high-power optical source will greatly push its application in supercontinuum generation, coherence tomography, and industrial processing.

Cladding-pumped Raman fiber laser with 0.78%quantum defect enabled by phosphorus-doped fiber

The quantum defect(QD)is an important issue that demands prompt attention in high-power fiber lasers.A large QD may aggravate the thermal load in the laser,which would impact the frequency,amplitude noise and mode stability,and threaten the security of the high-power laser system.Here,we propose and demonstrate a cladding-pumped Raman fiber laser(RFL)with QD of less than 1%.Using the Raman gain of the boson peak in a phosphorus-doped fiber to enable the cladding pump,the QD is reduced to as low as 0.78%with a 23.7 W output power.To our knowledge,this is the lowest QD ever reported in a cladding-pumped RFL.Furthermore,the output power can be scaled to 47.7 W with a QD of 1.29%.This work not only offers a preliminary platform for the realization of high-power low-QD fiber lasers,but also proves the great potential of low-QD fiber lasers in power scaling.

A proposal for the generation of optical frequency comb in temperature insensitive microcavity

We numerically simulate the generation of an optical frequency comb（OFC） in a microring based on the traditional Si_3N_4 strip waveguide and a temperature compensated slot waveguide.The results show that OFCs are susceptible to temperature with strip waveguide while they can keep stable when temperature changes 10 Kin either low-Q（10-5） or highQ（10-6） microcavity with the well-designed slot waveguide,which has great superiority in practical applications where the temperature drift of the cavity due to the intense pump or surrounding change is unavoidable.

LD-Pumped Random Fiber Laser Based on Erbium-Ytterbium Co-Doped Fiber

In this paper,a cladding-pumped erbium-ytterbium co-doped random fiber laser(EYRFL)operating at 1550 nm with high power laser diode(LD)is proposed and experimentally demonstrated for the first time.The laser cavity includes a 5-m-long erbium-ytterbium co-doped fiber that serves as the gain medium,as well as a 2-km-long single-mode fiber(SMF)to provide random distributed feedback.As a result,stable 2.14 W of 1550 nm random lasing at 9.80 W of 976 nm LD pump power and a linear output with the slope efficiency as 22.7%are generated.This simple and novel random fiber laser could provide a promising way to develop high power 1.5μm light sources.

307 W high-power 1018 nm monolithic tandem pump fiber source with effective thermal management

We report a 307 W 1018 nm Yb-doped fiber laser pumped by a single 976 nm laser diode. The cavity slope efficiency is up to 75.9% and the amplified spontaneous emission is suppressed by 54 dB. The beam quality of the output laser has an M2 factor of 1.17. Effective thermal management is considered to ensure the stable operation of our system. The power stability at the maximum output power level is measured during a period of0.5 h and the power fluctuation is less than 0.8%. This architecture can be an effective high brightness pump source of core-pumping high-power fiber amplifiers.

255 W picosecond MOPA laser based on self-made Yb-doped very-large-mode-area photonic crystal fiber

We report on the amplification of high-average-power and high-efficiency picosecond pulses in a self-made verylarge-mode-area Yb-doped photonic crystal fiber（PCF）. The PCF with a core diameter of 105 μm and a core numerical aperture of 0.05 is prepared by the sol-gel method combined with the powder sintering technique. The fiber amplification system produces the highest average power of 255 W at a 10 MHz repetition rate with a 21 ps pulse duration corresponding to a peak power of 1.2 MW. This result exemplifies the high-average-power and high-peak-power potential of this specifically designed fiber.

High-power Tm^(3+)-doped all-fiber laser operating at1908 nm by a master oscillator power amplifier configuration with narrow spectral linewidth

We demonstrate a diode-pump Tm^（3＋）t-doped all-fiber laser operating at 1908 nm based on a master oscillator power amplifier（MOPA） configuration. In our work, 152 W of laser output power is generated by a total incident pump power of 434 W at 790 nm, corresponding to the total optical efficiency of 35%. The laser wavelength is1908.29 nm. To the best of our knowledge, it is the highest output power reached around 1908 nm with such a narrow linewidth of 0.18 nm based on a MOPA configuration.

High-efficiency^2μm laser in a single-mode Tm-doped lead germanate composite fiber

A highly Tm-doped lead germanate glass fiber is developed using the rod-in-tube method. The -2 μm laser beam quality of the fiber is -1.5. The lead germanate composite fiber jumpers are homemade for all the fiber laser investigations. When core is pumped by a 1590 nm Yb/Er fiber laser, a maximum laser output of 313 mW is achieved at a 670 mW pump power, and the corresponding slope efficiency is -52.8%. Moreover, by using a 2 cmlong lead germanate fiber as the gain medium, a 33 mW 1942 nm Tm laser is also demonstrated.