关于*r-clean环

称对合环为*r-clean环是指环中任一元素都可表示为投射子和*-正则元的和.研究了该环的一些扩张性质,并给出了*-阿贝尔的*r-clean环中元素的刻画.

Correlation of periodontal inflamed surface area with glycated hemoglobin,interleukin-6 and lipoprotein(a)in type 2 diabetes with retinopathy

BACKGROUND The two-way relationship between periodontitis and type 2 diabetes mellitus(T2DM)is well established.Prolonged hyperglycemia contributes to increased periodontal destruction and severe periodontitis,accentuating diabetic complications.An inflammatory link exists between diabetic retinopathy(DR)and periodontitis,but the studies regarding this association and the role of lipoprotein(a)[Lp(a)]and interleukin-6(IL-6)in these conditions are scarce in the literature.AIM To determine the correlation of periodontal inflamed surface area(PISA)with glycated Hb(HbA1c),serum IL-6 and Lp(a)in T2DM subjects with retinopathy.METHODS This cross-sectional study comprised 40 T2DM subjects with DR and 40 T2DM subjects without DR.All subjects were assessed for periodontal parameters[bleeding on probing(BOP),probing pocket depth,clinical attachment loss(CAL),oral hygiene index-simplified,plaque index(PI)and PISA],and systemic parameters[HbA1c,fasting plasma glucose and postprandial plasma glucose,fasting lipid profile,serum IL-6 and serum Lp(a)].RESULTS The proportion of periodontitis in T2DM with and without DR was 47.5%and 27.5%respectively.Severity of periodontitis,CAL,PISA,IL-6 and Lp(a)were higher in T2DM with DR group compared to T2DM without DR group.Significant difference was observed in the mean percentage of sites with BOP between T2DM with DR(69%)and T2DM without DR(41%),but there was no significant difference in PI(P>0.05).HbA1c was positively correlated with CAL(r=0.351,P=0.001),and PISA(r=0.393,P≤0.001)in study subjects.A positive correlation was found between PISA and IL-6(r=0.651,P<0.0001);PISA and Lp(a)(r=0.59,P<0.001);CAL and IL-6(r=0.527,P<0.0001)and CAL and Lp(a)(r=0.631,P<0.001)among study subjects.CONCLUSION Despite both groups having poor glycemic control and comparable plaque scores,the periodontal parameters were higher in DR as compared to T2DM without DR.Since a bidirectional link exists between periodontitis and DM,the presence of DR may have contributed to the severity of periodontal destruction and periodontitis may have influenced the progression of DR.

Seismic response of a mid-story isolated structure considering SSI in mountainous areas under long-period earthquakes

At present,there is not much research on mid-story isolated structures in mountainous areas.In this study,a model of a mid-story isolated structure considering soil-structure interaction(SSI)in mountainous areas is established along with a model that does not consider SSI.Eight long-period earthquake waves and two ordinary earthquake waves are selected as inputs for the dynamic time history analysis of the structure.The results show that the seismic response of a mid-story isolated structure considering SSI in mountainous areas can be amplified when compared with a structure that does not consider SSI.The structure response under long-period earthquakes is larger than that of ordinary earthquakes.The structure response under far-field harmonic-like earthquakes is larger than that of near-fault pulse-type earthquakes.The structure response under near-fault pulse-type earthquakes is larger than that of far-field non-harmonic earthquakes.When subjected to long-period earthquakes,the displacement of the isolated bearings exceeded the limit value,which led to instability and overturning of the structure.The structure with dampers in the isolated story could adequately control the nonlinear response of the structure,effectively reduce the displacement of the isolated bearings,and provide a convenient,efficient and economic method not only for new construction but also to retrofit existing structures.

英语强化词Clean的语法化研究

本文以英语强化词“clean”为研究对象,进行语法化的历时演变个案研究。研究基于《牛津英语词典》以及美国历史英语语料库中的语料,分析了强化词“clean”的语法化演变路径、演变机制和动因。研究最后得出结论,“clean”经历了实义形容词到低强化副词再到高强化副词的语法化演变路径,主要分为两个阶段;其演变过程中主要体现了隐喻转喻与主观化两大演变机制,动因主要是语义泛化和效率性动因,并且机制和动因充分体现了人类作为语言使用者的主体性特征。该研究在一定程度上丰富了英语强化词语法化的个案研究,具有一定的参考价值和意义。This paper focuses on the English intensifier “clean”, presenting a case study for its grammaticalization. Based on the Old English Dictionary and the Corpus of Historical American English, the study analyzes the evolutionary path, mechanism and motivation of the grammaticalization of “clean”. The study concludes that with two stages, the evolutionary path is from notional adjective to low-intensive functional adverb, and then to high-intensive functional adverb. Metaphor and metonymy as well as subjectivity are the main mechanisms, while semantic generalization and efficiency factor serve as motivations. Both the mechanism and the motivation demonstrate the predominant role of human beings. This study, to some degree, enriches the case study of the grammaticalization of English intensifiers, with some reference value and significance.

Diversity of Orchids in Terms of Their Distribution, Uses and Conservation in Annapurna Conservation Area of Nepal

The Annapurna Conservation Area (ACA), the first conservation area and the largest protected area (PA) in Nepal, is incredibly rich in biodiversity. Notwithstanding this, orchids in the ACA have not been explored enough yet thus making the need for ambitious research to be carried out. Previous study only included 81 species of orchids within ACA. This study aims to update the record of species and genera richness in the ACA. In total 198 species of orchids, belonging to 67 genera (40% and 62% of the total recorded orchid species and genera in Nepal) has been recorded in ACA. This represents an increase of 144% in species and 56% in genera over the previous data. Out of the 198 species, 99 were epiphytes, 6 were holomycotrophic and 93 were terrestrial. Among the 67 genera, Bulbophyllum (17) species were dominant, followed by Dendrobium (16), Herminium (10), Coelogyne, Plantanthera (9 each), Eria, Habenaria, Oberonia (8 each), Calanthe (7), and Liparis (6). Fifty-six species were found to be ornamentally significant and 85 species medicinally significant.

Cleaning of two mirrors in the first mirror unit using radiofrequency capacitively coupled plasma

First mirror(FM)cleaning,using radio frequency(RF)plasma,has been proposed to recover FM reflectivity in nuclear fusion reactors such as the International Thermonuclear Experimental Reactor(ITER).To investigate the influence of simultaneous cleaning of two mirrors on mirror cleaning efficiency and uniformity,experiments involving single-mirror cleaning and dual-mirror cleaning were conducted using RF capacitively coupled plasma in the laboratory.For the test and simultaneous cleaning of two mirrors,the FM and second mirror(SM),both measuring 110 mm×80 mm,were placed inside the first mirror unit(FMU).They were composed of 16 mirror samples,each with a dimension of 27.5 mm×20 mm.These mirror samples consist of a titanium-zirconium-molybdenum alloy substrate,a 500 nm Mo intermediate layer and a 30 nm Al_(2)O_(3) surface coating as a proxy for Be impurities.The cleaning of a single first mirror(SFM)and the simultaneous cleaning of the FM and SM(DFM and DSM)lasted for 9 h using Ar plasma at a pressure of 1 Pa.The total reflectivity of mirror samples on the DSM did not fully recover and varied with location,with a self-bias of−140 V.With a self-bias of−300 V,the total reflectivity of mirror samples on the SFM and DFM was fully recovered.The energy dispersive spectrometer results demonstrated that the Al_(2)O_(3) coating had been completely removed from these mirror samples.However,the mass loss of each mirror sample on the SFM and DFM before and after cleaning varied depending on its location,with higher mass loss observed for mirror samples located in the corners and lower loss for those in the center.Compared with SM cleaning,the simultaneous cleaning of two mirrors reduced the difference between the highest and lowest mass loss.Furthermore,this mass loss for the mirror samples of the DFM facing the DSM was increased.This indicated that mirror samples cleaned face to face in the FMU simultaneously could influence each other,highlighting the need for special attention in future studies.

The environmental analysis and site selection of mussel and large yellow croaker aquaculture areas based on high resolution remote sensing

Mussel aquaculture and large yellow croaker aquaculture areas and their environmental characteristics in Zhoushan were analyzed using satellite data and in-situ surveys.A new two-step remote sensing method was proposed and applied to determine the basic environmental characteristics of the best mussel and large yellow croaker aquaculture areas.This methodology includes the first step of extraction of the location distribution and the second step of the extraction of internal environmental factors.The fishery ranching index(FRI1,FRI2)was established to extract the mussel and the large yellow croaker aquaculture area in Zhoushan,using Gaofen-1(GF-1)and Gaofen-6(GF-6)satellite data with a special resolution of 2 m.In the second step,the environmental factors such as sea surface temperature(SST),chlorophyll a(Chl-a)concentration,current and tide,suspended sediment concentration(SSC)in mussel aquaculture area and large yellow croaker aquaculture area were extracted and analyzed in detail.The results show the following three points.(1)For the extraction of the mussel aquaculture area,FRI1 and FRI2 are complementary,and the combination of FRI1 and FRI2 is suitable to extract the mussel aquaculture area.As for the large yellow croaker aquaculture area extraction,FRI2 is suitable.(2)Mussel aquaculture and the large yellow croaker aquaculture area in Zhoushan are mainly located on the side near the islands that are away from the eastern open waters.The water environment factor template suitable for mussel and large yellow croaker aquaculture was determined.(3)This two-step remote sensing method can be used for the preliminary screening of potential site selection for the mussels and large yellow croaker aquaculture area in the future.the fishery ranching index(FRI1,FRI2)in this paper can be applied to extract the mussel and large yellow croaker aquaculture areas in coastal waters around the world.

Prevalence of Malnutrition and Anaemia in Children ≤ 5 Years of Age in Some Conflict Hit Areas of Meme Division of the South West Region of Cameroon

Malnutrition refers to the deficiency, imbalances, or excesses in a person’s intake of energy or nutrients [1]. Khan defines anaemia as below level of Haemoglobin in red blood shown by a lower number of functioning red blood cells [2]. The crisis in the North West and South West Regions of Cameroon has led to several negative effects on children’s living conditions. There has been an increase in malnutrition and anaemia in the South West Region and Kumba in particular. The main objective of this study was “to examine the prevalence of malnutrition and anaemia in children ≤ 5 years of age in some conflict-hit areas of Meme Division”. A descriptive cross-sectional study was conducted in 2023 from March to June. We recruited 200 children ≤ 5 years into the study from three hospitals. The regional hospital annex in Kumba, Presbyterian General Hospital Kumba and the Ntam Hospital in Kumba. Socio-demographic factors were assessed using questionnaire, nutritional status was assessed by the use anthropometric measurements and an auto haematology analyser was used to determine anaemia. The overall prevalence of malnutrition in the study area was 40.5%. The prevalence of malnutrition varied significantly (P < 0.001) with the study sites. The overall prevalence of anaemia in the study area was 70.5%. The prevalence of anaemia was not significantly associated with the study sites. The prevalence of Malnutrition and Anaemia in children ≤ 5 years of age is very high in the Kumba municipalities. This could be attributed to the ongoing crisis which has caused a lot of social migrations from rural areas to Urban areas which are safer.

New steelmaking process based on clean deoxidation technology

After the converter steelmaking process,a considerable number of ferroalloys are needed to remove dissolved oxygen from the molten steel,but it also forms a lot of oxide inclusions that cannot be completely removed.At the same time,it increases the carbon emis-sions in the steel production process.After years of research,our team have developed a series of clean deoxidation technologies,includ-ing carbon deoxidation,hydrogen deoxidation,and waste plastic deoxidation of molten steel to address the aforementioned issues.In this study,thermodynamic calculations and laboratory experiments were employed to verify that carbon and hydrogen can reduce the total oxygen content in the molten steel melt to below 5×10^(-6) and 10×10^(-6),respectively.An analysis of the deoxidation mechanisms and ef-fects of polyethylene and polypropylene was also conducted.In addition,the applications of carbon deoxidation technology in different steels with the hot-state experiment and industrial production were discussed carefully.The carbon deoxidation experimental results of different steels were as follows:(1)the oxygen content of bearing steel was effectively controlled at 6.3×10^(-6) and the inclusion number density was lowered by 74.73%compared to aluminum deoxidized bearing steel;(2)the oxygen content in gear steel was reduced to 7.7×10^(-6) and a 54.49%reduction of inclusion number density was achieved with almost no inclusions larger than 5μm from the average level of industry gear steels;(3)a total oxygen content of M2 high-speed steel was as low as 3.7×10^(-6).In industrial production practice,car-bon deoxidation technique was applied in the final deoxidation stage for non-aluminum deoxidized bearing steel,and it yielded excellent results that the oxygen content was reduced to below 8×10^(-6) and the oxide inclusions in the steel mainly consist of silicates,along with small amounts of spinel and calcium aluminate.

Hole cleaning evaluation and installation spacing optimization of cuttings bed remover in extended-reach drilling

In extended-reach or long-horizontal drilling,cuttings usually deposit at the bottom of the annulus.Once cuttings accumulate to a certain thickness,complex problems such as excessive torque and drag,tubing buckling,and pipe stuck probably occur,which results in a lot of non-productive time and remedial operations.Cuttings bed remover can efficiently destroy deposited cuttings in time through hydraulic and mechanical stirring effects.This paper aims to build a method for hole cleaning evaluation and installation spacing optimization of cuttings bed remover to improve the wellbore cleaning effect.Firstly,a Computational Fluid Dynamics approach with Eulerian—Eulerian multiphase model was utilized to investigate the mechanism of cuttings transportation,and a new type of cuttings bed remover was designed.Next,an evaluation method of hole cleaning effect of remover was established.After that,the effects of several drilling parameters on hole cleaning including flow rate of drilling fluid,rotational speed of drillpipe,rate of penetration,wellbore size,rheological property of drilling fluid,and remover eccentricity on the performance of cuttings bed remover were investigated.The results demonstrate that the new type of remover with streamline blade performs better than conventional removers.The efficiency of hole cleaning is greatly improved by increasing the rotational speed of drillpipe,flow rate of drilling fluid,remover eccentricity,and 6 rpm Fann dial reading for drilling fluid.While higher rate of penetration and large wellbore size result in worse hole cleaning.These findings can serve as an important guide for the structure optimization design of cuttings bed remover and installation spacing of removers.

Experimental investigation on coal pore-fracture variation and fractal characteristics synergistically affected by solvents for improving clean gas extraction

Chemical solvents instead of pure water being as hydraulic fracturing fluid could effectively increase permeability and improve clean methane extraction efficiency.However,pore-fracture variation features of lean coal synergistically affected by solvents have not been fully understood.Ultrasonic testing,nuclear magnetic resonance analysis,liquid phase mass spectrometry was adopted to comprehensively analyze pore-fracture change characteristics of lean coal treated by combined solvent(NMP and CS_(2)).Meanwhile,quantitative characterization of above changing properties was conducted using geometric fractal theory.Relationship model between permeability,fractal dimension and porosity were established.Results indicate that the end face fractures of coal are well developed after CS2and combined solvent treatments,of which,end face box-counting fractal dimensions range from 1.1227 to 1.4767.Maximum decreases in ultrasonic longitudinal wave velocity of coal affected by NMP,CS_(2)and combined solvent are 2.700%,20.521%,22.454%,respectively.Solvent treatments could lead to increasing amount of both mesopores and macropores.Decrease ratio of fractal dimension Dsis 0.259%–2.159%,while permeability increases ratio of NMR ranges from 0.1904 to 6.4486.Meanwhile,combined solvent could dissolve coal polar and non-polar small molecules and expand flow space.Results could provide reference for solvent selection and parameter optimization of permeability-enhancement technology.

Exploring well-being disparities between urban and rural areas:A case study in the Stavropol Territory,Russia

Rural areas are crucial for a country’s sustainable economy.New strategies are needed to develop rural areas to improve the well-being of rural population and generate new job opportunities.This is especially important in countries where agricultural production accounts for a significant share of the gross product,such as Russia.In this study,we identified the key indicators of satisfaction and differences between rural and urban citizens based on their social,economic,and environmental backgrounds,and determined whether there are well-being disparities between rural and urban areas in the Stavropol Territory,Russia.We collected primary data through a survey based on the European Social Survey framework to investigate the potential differences between rural and urban areas.By computing the regional well-being index using principal component analysis,we found that there was no statistically significant difference in well-being between rural and urban areas.Results of key indicators showed that rural residents felt psychologically more comfortable and safer,assessed their family relationships better,and adhered more to traditions and customs.However,urban residents showed better economic and social conditions(e.g.,infrastructures,medical care,education,and Internet access).The results of this study imply that we can better understand the local needs,advantages,and unique qualities,thereby gaining insight into the effectiveness of government programs.Policy-makers and local authorities can consider targeted interventions based on the findings of this study and strive to enhance the well-being of both urban and rural residents.

Investigation of an electrode-driven hydrogen plasma method for in situ cleaning of tin-based contamination

To prolong the service life of optics,the feasibility of in situ cleaning of the multilayer mirror(MLM)of tin and its oxidized contamination was investigated using hydrogen plasma at different power levels.Granular tin-based contamination consisting of micro-and macroparticles was deposited on silicon via physical vapor deposition(PVD).The electrodedriven hydrogen plasma at different power levels was systematically diagnosed using a Langmuir probe and a retarding field ion energy analyzer(RFEA).Moreover,the magnitude of the self-biasing voltage was measured at different power levels,and the peak ion energy was corrected for the difference between the RFEA measurements and the self-biasing voltage(E_(RFEA)-eV_(self)).XPS analysis of O 1s and Sn 3d peaks demonstrated the chemical reduction process after 1 W cleaning.Analysis of surface and cross-section morphology revealed that holes emerged on the upper part of the macroparticles while its bottom remained smooth.Hills and folds appeared on the upper part of the microparticles,confirming the top-down cleaning mode with hydrogen plasma.This study provides an in situ electrode-driven hydrogen plasma etching process for tin-based contamination and will provide meaningful guidance for understanding the chemical mechanism of reduction and etching.

Glacier area change (1993-2019) and its relationship to debris cover, proglacial lakes, and morphological parameters in the Chandra-Bhaga Basin, Western Himalaya, India

Glacier inventories serve as critical baseline data for understanding the impacts of climate change on glaciers.The present study maps the outlines of glaciers in the Chandra-Bhaga Basin(western Himalaya)for the years 1993,2000,2010,and 2019 using Landsat Thematic Mapper(TM),Enhanced Thematic Mapper(ETM),and Operational Land Imager(OLI)datasets.A total of 251 glaciers,each having an area above 0.5 km^(2),were identified,which include 216 clean-ice and 35 debris-covered glaciers.Area changes are estimated for three periods:1993-2000,2000-2010,and 2010-2019.The total glacierized area was 996±62 km^(2) in 1993,which decreased to 973±70 km^(2) in 2019.The mean rate of glacier area loss was higher in the recent decade(2010-2019),at 0.036 km^(2),compared to previous decades(0.029 km^(2) in 2000-2010 and 0.025 km^(2) in 1993-2000).Supraglacial debris cover changes are also mapped over the period of 1993 and 2019.It is found that the supraglacial debris cover increased by 14.12±2.54 km^(2)(15.2%)during 1993-2019.Extensive field surveys on Chhota Shigri,Panchi II,Patsio,Hamtah,Mulkila,and Yoche Lungpa glaciers were carried out to validate the glacier outlines and supraglacial debris cover estimated using satellite datasets.Controls of various morphological parameters on retreat were also analyzed.It is observed that small,clean ice,south oriented glaciers,and glaciers with proglacial lakes are losing area at faster rates than other glaciers in the basin.

Wellbore Cleaning Degree and Hydraulic Extension in Shale Oil Horizontal Wells

The efficient development and exploitation of shale oil depends on long-distance horizontal wells. As the degreeof cleaning of the wellbore plays a key role in these processes, in this study, this problem is investigated experimentallyby focusing on the dimensionless cuttings bed height. A method is proposed to calculate the horizontalwellhydraulic extension taking into account the influence of the wellbore cleaning degree on the wellborepressure distribution and assess the effect of a variety of factors such as the bottom hole pressure, the circulatingpressure drop, the drilling pump performance and the formation properties. The analysis shows that the hydraulicextension of horizontal wells decreases with an increase in the cuttings bed height, and the higher the displacementof drilling fluid, the faster the hydraulic extension declines. The annular pressure drop of the horizontalsection increases with the increase of the cuttings bed height, resulting in a higher bottom-hole pressure. Severalarguments are provided to guide the safe drilling of shale oil horizontal wells and overcome the limits of currenttechnological approaches.

Acetylacetone-TiO_(2) Promoted Large Area Compatible Cascade Electron Transport Bilayer for Efficient Perovskite Solar Cells

In designing efficient perovskite solar cells(PSCs),the selection of suitable electron transport layers(ETLs)is critical to the final device performance as they determine the driving force for selective charge extraction.SnO_(2)nanoparticles(NPs)based ETLs have been a popular choice for PSCs due to superior electron mobility,but their relatively deep-lying conduction band energy levels(ECB)result in substantial potential loss.Meanwhile,TiO_(2)NPs establish favorable band alignment owing to shallower ECB,but their low intrinsic mobility and abundant surface trap sites impede the final performance.For this reason,constructing a cascaded bilayer ETL is highly desirable for efficient PSCs,as it can rearrange energy levels and exploit on advantages of an individual ETL.In this study,we prepare SnO_(2)NPs and acetylacetone-modified TiO_(2)(Acac-TiO_(2))NPs and implement them as bilayer SnO_(2)/Acac-TiO_(2)(BST)ETL,to assemble cascaded energy band structure.SnO_(2)contributes to rapid charge carrier transport from high electron mobility while Acac-TiO_(2)minimizes band-offset and effectively suppresses interfacial recombination.Accordingly,the optimized BST ETL generates synergistic influence and delivers power conversion efficiency(PCE)as high as 23.14%with open-circuit voltage(V_(oc))reaching 1.14 V.Furthermore,the BST ETL is transferred to a large scale and the corresponding mini module demonstrates peak performance of 18.39%PCE from 25 cm^(2)aperture area.Finally,the BST-based mini module exhibit excellent stability,maintaining 83.1%of its initial efficiency after 1000 h under simultaneous 1 Sun light-soaking and damp heat(85℃/RH 85%)environment.

A method for cleaning wind power anomaly data by combining image processing with community detection algorithms

Current methodologies for cleaning wind power anomaly data exhibit limited capabilities in identifying abnormal data within extensive datasets and struggle to accommodate the considerable variability and intricacy of wind farm data.Consequently,a method for cleaning wind power anomaly data by combining image processing with community detection algorithms(CWPAD-IPCDA)is proposed.To precisely identify and initially clean anomalous data,wind power curve(WPC)images are converted into graph structures,which employ the Louvain community recognition algorithm and graph-theoretic methods for community detection and segmentation.Furthermore,the mathematical morphology operation(MMO)determines the main part of the initially cleaned wind power curve images and maps them back to the normal wind power points to complete the final cleaning.The CWPAD-IPCDA method was applied to clean datasets from 25 wind turbines(WTs)in two wind farms in northwest China to validate its feasibility.A comparison was conducted using density-based spatial clustering of applications with noise(DBSCAN)algorithm,an improved isolation forest algorithm,and an image-based(IB)algorithm.The experimental results demonstrate that the CWPAD-IPCDA method surpasses the other three algorithms,achieving an approximately 7.23%higher average data cleaning rate.The mean value of the sum of the squared errors(SSE)of the dataset after cleaning is approximately 6.887 lower than that of the other algorithms.Moreover,the mean of overall accuracy,as measured by the F1-score,exceeds that of the other methods by approximately 10.49%;this indicates that the CWPAD-IPCDA method is more conducive to improving the accuracy and reliability of wind power curve modeling and wind farm power forecasting.

满足DNV船级符号Clean(Design)要求的轮机设备订货及系统设计

为有效避免在船舶产品设计过程中出现疏漏,研究挪威船级社船级符号Clean(Design)对轮机设备订货、系统设计和舱柜布置的最新要求,并对各设备和系统的特殊要求及设计原则进行梳理和归纳。用于处理污染物的设备主要包括油水分离器、污水处理装置和焚烧炉,涉及的船舶系统主要包括舱底水系统、生活污水处理系统、泡沫灭火系统和艉管滑油系统等。该研究可供满足该规范要求的环保型船舶产品的设计参考。

Influences of clean fracturing fluid viscosity and horizontal in-situ stress difference on hydraulic fracture propagation and morphology in coal seam

The viscosity of fracturing fluid and in-situ stress difference are the two important factors that affect the hydraulic fracturing pressure and propagation morphology. In this study, raw coal was used to prepare coal samples for experiments, and clean fracturing fluid samples were prepared using CTAB surfactant. A series of hydraulic fracturing tests were conducted with an in-house developed triaxial hydraulic fracturing simulator and the fracturing process was monitored with an acoustic emission instrument to analyze the influences of fracturing fluid viscosity and horizontal in-situ stress difference on coal fracture propagation. The results show that the number of branched fractures decreased, the fracture pattern became simpler, the fractures width increased obviously, and the distribution of AE event points was concentrated with the increase of the fracturing fluid viscosity or the horizontal in-situ stress difference. The acoustic emission energy decreases with the increase of fracturing fluid viscosity and increases with the increase of horizontal in situ stress difference. The low viscosity clean fracturing fluid has strong elasticity and is easy to be compressed into the tip of fractures, resulting in complex fractures. The high viscosity clean fracturing fluids are the opposite. Our experimental results provide a reference and scientific basis for the design and optimization of field hydraulic fracturing parameters.

Food Hygiene and Safety Practices amongst Food Vendors in the Western Area, Sierra Leone

Food safety and hygiene practices require a multisectoral approach including food, water, sanitation, waste management, transport, education, trade, policies and programs that enable safe food preparation, storage and service. Unsafe food can cause illness keeping people from achieving their full potential and death. This was a descriptive study that uses a mixed method approach to derive insights into the characteristics of food vendors related to demography, knowledge, practices, infrastructure, compliance and recommendation for a policymaking framework. Using the Lemeshows’ sample size formula, 473 vendors from formal (restaurants) and informal (cookri-baffa/table top) sites were interviewed and observed. We found from discussions that respondents had a good understanding on how to keep food safe. However, observed practices were poor 93% handled food with their bare hands, 83% did not cover their hair, and 76% did not wear an apron whilst handling, preparing or serving food, 61% did not keep their finger nails clean or short and 57% did not wash their hand before preparing or serving food. Over half (51%) had access to a toilet but 32% reported their use required payment and emphasized their poor condition/inadequate management. Nearly half (47%) of the vending sites did not have a handwashing facility, with soap and water available. Only 7% reported having any authority oversight of food safety. Food safety and hygiene practices in most cookri shops and restaurants was ‘poor’ with very limited surveillance system in place by competent authorities for compliance of food operators. Hand washing, clean surroundings, and covered food were the most common and emphasized practices to mitigate the risks associated with unsafe food.