Hole cleaning evaluation and installation spacing optimization of cuttings bed remover in extended-reach drilling

In extended-reach or long-horizontal drilling,cuttings usually deposit at the bottom of the annulus.Once cuttings accumulate to a certain thickness,complex problems such as excessive torque and drag,tubing buckling,and pipe stuck probably occur,which results in a lot of non-productive time and remedial operations.Cuttings bed remover can efficiently destroy deposited cuttings in time through hydraulic and mechanical stirring effects.This paper aims to build a method for hole cleaning evaluation and installation spacing optimization of cuttings bed remover to improve the wellbore cleaning effect.Firstly,a Computational Fluid Dynamics approach with Eulerian—Eulerian multiphase model was utilized to investigate the mechanism of cuttings transportation,and a new type of cuttings bed remover was designed.Next,an evaluation method of hole cleaning effect of remover was established.After that,the effects of several drilling parameters on hole cleaning including flow rate of drilling fluid,rotational speed of drillpipe,rate of penetration,wellbore size,rheological property of drilling fluid,and remover eccentricity on the performance of cuttings bed remover were investigated.The results demonstrate that the new type of remover with streamline blade performs better than conventional removers.The efficiency of hole cleaning is greatly improved by increasing the rotational speed of drillpipe,flow rate of drilling fluid,remover eccentricity,and 6 rpm Fann dial reading for drilling fluid.While higher rate of penetration and large wellbore size result in worse hole cleaning.These findings can serve as an important guide for the structure optimization design of cuttings bed remover and installation spacing of removers.

Bridge Plug Drillouts Cleaning Practices—An Overview

Horizontal fracture-simulated completions remain the most reliable method of producing hydrocarbons from shale formations. The vast majority of unconventional wells are completed using the “Plug and Perf” method. This method involves using either a coiled tubing (CT) with a positive displacement motor or a jointed pipe to mill out composite plugs after fracturing operations are completed. An estimated average of 120,000 composite plugs is installed in the US alone each year. Bridge plug drillouts from milling operations tend to accumulate in horizontal wells and can cause stuck pipe incidents and loss of well control. Efficient removal of composite plugs’ debris is crucial in achieving operational efficacies and full production potential. This paper provides an overview of the various bridge plug drillouts cleaning practices adopted in horizontal wells. It discusses several case histories, showcasing how operators solved cleanout challenges. Developed mechanistic models to better understand hole cleaning are also reviewed. As more unconventional wells are being set at more extensive depths, an economical and optimized coiled tubing process becomes increasingly important. This paper focuses on delivering a more conclusive set of recommendations to increase efficiency and improve current composite plug coiled tubing cleaning-milling practices, increase operational efficiency and reduce cost.

Synthetic polymers:A review of applications in drilling fluids

With the growth of deep drilling and the complexity of the well profile,the requirements for a more complete and efficient exploitation of productive formations increase,which increases the risk of various complications.Currently,reagents based on modified natural polymers(which are naturally occurring compounds)and synthetic polymers(SPs)which are polymeric compounds created industrially,are widely used to prevent emerging complications in the drilling process.However,compared to modified natural polymers,SPs form a family of high-molecular-weight compounds that are fully synthesized by undergoing chemical polymerization reactions.SPs provide substantial flexibility in their design.Moreover,their size and chemical composition can be adjusted to provide properties for nearly all the functional objectives of drilling fluids.They can be classified based on chemical ingredients,type of reaction,and their responses to heating.However,some of SPs,due to their structural characteristics,have a high cost,a poor temperature and salt resistance in drilling fluids,and degradation begins when the temperature reaches 130℃.These drawbacks prevent SP use in some medium and deep wells.Thus,this review addresses the historical development,the characteristics,manufacturing methods,classification,and the applications of SPs in drilling fluids.The contributions of SPs as additives to drilling fluids to enhance rheology,filtrate generation,carrying of cuttings,fluid lubricity,and clay/shale stability are explained in detail.The mechanisms,impacts,and advances achieved when SPs are added to drilling fluids are also described.The typical challenges encountered by SPs when deployed in drilling fluids and their advantages and drawbacks are also discussed.Economic issues also impact the applications of SPs in drilling fluids.Consequently,the cost of the most relevant SPs,and the monomers used in their synthesis,are assessed.Environmental impacts of SPs when deployed in drilling fluids,and their manufacturing processes are identified,together with advances in SP-treatment methods aimed at reducing those impacts.Recommendations for required future research addressing SP property and performance gaps are provided.

Simulation study on cuttings transport of the backreaming operation for long horizontal section wells

The backreaming operation plays a significant role in safe drilling for horizontal wellbores, while it may cause severe stuck pipe accidents. To lower the risk of the stuck pipe in backreaming operations, the mechanism of cuttings transport needs to be carefully investigated. In this research, a transient cuttings transport with multiple flow patterns model is developed to predict the evolution of cuttings transported in the annulus while backreaming. The established model can provide predictions of the distribution of cuttings bed along the wellbore considering the bulldozer effect caused by large-size drilling tools(LSDTs). The sensitivity analyses of the size of LSDTs, and backreaming operating parameters are conducted in Section 4. And a new theory is proposed to explain the mechanism of cuttings transport in the backreaming operation, in which both the bit and LSDTs have the “cleaning effect” and “plugging effect”.The results demonstrate that the cuttings bed in annuli is in a state of dynamic equilibrium, but the overall trend and the distribution pattern are obvious. First, larger diameters and longer drilling tools could lead to a higher risk of the stuck pipe. Second, we find that it is not the case that the higher flow rate is always better for hole cleaning, so three flow-rate intervals are discussed separately under the given conditions. When the “dangerous flow rate”(<33 L/s in Case 4) is employed, the cuttings bed completely blocks the borehole near the step surface and causes a stuck pipe directly. If the flow rate increases to the “low flow rate” interval(33-35 L/s in Case 4), a smaller flow rate instead facilitates borehole cleaning. If the flow rate is large enough to be in the “high flow rate” interval(>35 L/s in Case 4),the higher the flow rate, the better the cleaning effect of cuttings beds. Third, an interval of tripping velocity called “dangerous velocity” is proposed, in which the cuttings bed accumulation near the LSDTs is more serious than those of other tripping velocities. As long as the applied tripping velocity is not within the “dangerous velocity”(0.4-0.5 m/s in Case 5) interval in the backreaming operation, the risk of the stuck pipe can be controlled validly. Finally, through the factors analyses of the annular geometry,particle properties, and fluid properties in Section 5, it can be found that the “low flow rate”, “high flow rate” and “dangers flow rate” tend to decrease and the “dangerous velocity” tends to increase with the conditions more favorable for hole cleaning. This study has some guiding significance for risk prediction and parameter setting of the backreaming operation.

A novel predictive model of drag coefficient and settling velocity of drill cuttings in non-Newtonian drilling fluids

In oil and gas well drilling operations,it is of great significance to accurately predict the drag coefficient and settling velocity of drill cuttings in non-Newtonian drilling fluids.In this paper,the free-falling of 172 groups of spheres and 522 groups of irregular-shaped sand particles in Newtonian/non-Newtonian fluids were investigated experimentally.It was found that the drag coefficient calculated based on Newtonian correlations can result in a significant error when the particle settles in the non-Newtonian fluid.Therefore,predictive models of drag coefficient were established respectively for different types of fluids.The validity of the proposed drag coefficient model of spheres was verified by comparing it with the previous works.On this basis,the drag coefficient model of irregular-shaped sand particles was established by introducing a shape factor.The models do not use the shape factor that requires detailed threedimensional shape and size information.Instead,two-dimensional geometric information(circularity)is obtained via image analysis techniques.The present new models predict the settling velocity of sand particles in the power-law fluid and Herschel-Bulkley fluid accurately with a mean relative error of5.03%and 6.74%,respectively,which verifies the accuracy of the model.

Cuttings transport: Back reaming analysis based on a coupled layering-sliding mesh method via CFD

Inadequate hole cleaning is one of the main reasons for inefficient operations in extended-reach drilling.The mechanism of cuttings transport under the back reaming operation,which is frequently adopted to remove the cuttings,has been investigated in this study.To this end,a coupled layering-sliding mesh method with the Eulerian-Granular approach has been established innovatively.The dynamic layering method has been employed to simulate the axial motion of the pipe,whereas the sliding mesh method has been used to simulate the pipe rotation.The back reaming operation of a connector-furnished pipe has been simulated,and the sensitive parameter analysis has been conducted.The results thus obtained demonstrate that the increase in the initial bed height,inclination,and the diameter and length of the connector causes a significant increase in the cuttings concentration.In addition,the cuttings concentration is observed to decrease significantly with the pipe rotation speed.Furthermore,two main factors contribute towards the cuttings accumulation around the connector,namely,the difference in the cross-sectional area and the pushing effect of the connector—like a“bulldozer”.The“bulldozer”effect of the connector dominates when the tripping velocity is significant compared to the velocity of the cuttings.Conversely,the effect of the difference in the cross-sectional area becomes the leading factor for cuttings accumulation.The“bulldozer”effect of the connector causes a more severe impact on hole cleaning.In both cases,increasing the tripping velocity only mildly affects the cuttings concentration.It is therefore suggested that the tripping velocity should be slower than that of the sand during the back reaming operation.Furthermore,increased fluid velocity might lead to a higher accumulated cuttings concentration around the connector when the cuttings bed has not entirely passed through the connector.A significant flow rate can be safely applied after the cuttings have passed through the connector furnished with a large diameter,such as the bottom hole assembly.This exploration serves as an essential guide to predicting and controlling tight spots while back reaming.

Experimental investigation of multiphase flow behavior in drilling annuli using high speed visualization technique

Imaging with high definition video camera is an important technique to visualize the drilling conditions and to study the physics of complex multiphase flow associated with the hole cleaning process.The main advantage of visualizing multiphase flow in a drilling annulus is that the viewer can easily distinguish fluid phases,flow patterns and thicknesses of cutting beds.In this paper the hole cleaning process which involves the transportation of cuttings through a horizontal annulus was studied.The two-phase(solid-liquid)and the three-phase(solid-liquid-gas)flow conditions involved in this kind of annular transportation were experimentally simulated and images were taken using a high definition camera.Analyzing the captured images,a number of important parameters like velocities of different phases,heights of solid beds and sizes of gas bubbles were determined.Two different techniques based on an image analysis software and MATLAB coding were used for the determinations.The results were compared to validate the image analyzing methodology.The visualization technique developed in this paper has a direct application in investigating the critical conditions required for efficient hole cleaning as well as in optimizing the mud program during both planning and operational phases of drilling.Particularly,it would be useful in predicting the cuttings transport performance,estimating solid bed height,gas bubble size,and mean velocities of bubbles/particles.