COMPUTER SIMULATION OF GRAIN BOUNDARY SEGREGATION BEHAVIOR AND MECHANISMS OF STRENGTHENING OF Mg IN Ni-BASED SUPERALLOYS

This paper used EAM and static relaxation method to simulate the grain boundary segregation behavior of Mg in Ni-based superalloys. The results offer a better understanding in the strengthening mechanism of Mg addition in superalloys. The segregation of Mg increases the grain boundary cohesive bond and the vacancy formation energy, and decreases the mobility of grain boundary dislocation. It results in the retardation of creep voids initiation and growth.

Application of the Computer Simulation Technique to Developing EFI Engine

The application of computer simulation technique to electronic controlled fuel injection(EFI) engine was studied to increase the development speed and improve the overall performance of the engine and car. On the basis of an EFI system developed by ourselves, the simulation model of the initial control data and engine operation points during a driving cycle and the car performance pridiction model were established. This method was applied to a mini car. The experiment showed that the simulated control data has good accuracy; and the engine test points and car performances obtained by simulation are useful for the matching of EFI system with gasoline engine and the development speed is increased.

A VIDEO SPECTRUM SPLITTING ENCODING SCHEME BASED ON HUMAN VISION AND ITS COMPUTER SIMULATION

In this paper, a 3-D video encoding scheme suitable for digital TV/HDTV (high definition television) is studied through computer simulation. The encoding scheme is designed to provide a good match to human vision. Basically, this involves transmission of low frequency luminance information at full frame rate for good motion rendition and transmission of high frequency luminance signal at reduced frame rate for good detail in static images.

Computer Simulation of Compensation Method for Infrared Focal Plane Array

A major motivation for this work is to investigate a method of computer simulation for compensating fixed pattern noise of the infrared focal plane arrays. A mathematical model of the output signal of focal plane array was established; a compensating algorithm utilizing reference source was derived and simulating programs were designed. The images of compensating process verify the influence of nonuniformity of responsibility and offset on fixed pattern noise. The result show that simulating method of investigating compensation technology for focal plane arrays is feasible, the generated images and methods can be used to the study of image recognition.

DEVELOPMENT OF COMPUTER SIMULATION SOFTWAREON PHASE TRANSFORMATION DURING QUENCHING

A computer software to simulate the phase transformation during quenching is designed based on Avrami equation and Scheil additivity principle of incubation period. The isothermal transformation diagrams of supercooled austenite are described by cubic spline functions. This software is possess of a good graphic interface of Windows style, can simulate the whole process in austenite decomposition during continuous cooling. If the cooling rate was given, the fraction of various microstructures transformed of austenite decomposition during continuous cooling at any temperature can be calculated. The simulation results are checked with the quenching experiment of 45 steel. The results indicate that the simulation results are comparatively close to the experimental results.

MATHEMATICAL MODELS OF NITROGEN CONCENTRATION PROFILE OF ION NITRIDED LAYERS AND COMPUTER SIMULATION

The mathematical models of the kinetics of the layer growth at different ion nitriding condi- tions of armco iron.steels 45,40Cr,42CrMo and 38CrMoAl have been established.Based on these models the expression of nitrogen concentration profile of ion nitrided layers have been deduced with profile simulating method.They are C_=C_(min)^+(P_4)/(ξ_1-x)+(P_5)/(ξ_(10)~2)(ξ_1-x)~2 C_(γ′)=C_(min)^(γ′)+(P_1)/(ξ_(21))(ξ_2-x)+(P_2)/(ξ_(21)~2)(ξ_2-x)~2 C_α=C_(min)~α+(C_(33))/(C_(33))/(ξ_(32))(ξ_3-x)~3 Using these models,the kinetics of layer growth and the nitrogen concentration profile of ion nitrided layers were sinulated on Apple-Ⅱ computer.Results show that the simulated curves coincide quite well with the experimental data.

Comparison of Snellen and Early Treatment Diabetic Retinopathy Study charts using a computer simulation

AIM：To compare accuracy,reproducibility and test duration for the Snellen and the Early Treatment Diabetic Retinopathy Study（ETDRS）charts,two main tools used to measure visual acuity（VA）.·M ETHODS：A computer simulation was programmed to run multiple virtual patients,each with a unique set of assigned parameters,including VA,false-positive and false-negative error values.For each virtual patient,assigned VA was randomly chosen along a continuous scale spanning the range between 1.0 to 0.0 log MAR units（equivalent to 20/200 to 20/20）.Each of 30 000virtual patients were run ten times on each of the two VA charts.·RESULTS：Average test duration（expressed as the total number of characters presented during the test±SD）was12.6±11.1 and 31.2±14.7 characters,for the Snellen and ETDRS,respectively.Accuracy,defined as the absolute difference（±SD）between the assigned VA and the measured VA,expressed in log MAR units,was superior in the ETDRS charts：0.12±0.14 and 0.08±0.08,for the Snellen and ETDRS charts,respectively.Reproducibility,expressed as test-retest variability,was superior in the ETDRS charts：0.23±0.17 and 0.11±0.09 log MAR units,for the Snellen and ETDRS charts,respectively.·CONCLUSION：A comparison of true（assigned）VA to measured VA,demonstrated,on average,better accuracy and reproducibility of the ETDRS chart,but at the penalty of significantly longer test duration.These differences were most pronounced in the low VA range.The reproducibility using a simulation approach is in line with reproducibility values found in several clinical studies.

Computer Simulation of Ferrite Transformation during Hot Working of Low Carbon Steel

On the basis of transformation kinetics and thermodynamics, the austenite-ferrite transformation start temperature during deformation was predicted for several grades of low-carbon steels under different processing conditions. Results indicate that Ar3d temperature mostly depended on alloying composition and processing parameters. Ar3d increased as strain rate or strain increased for the same steel grade. In view of enhancement of deformation on transformation, the basic kinetics model was established to simulate deformation induced transformation behavior, using which the influence of the deformation stored energy and effective deformation ledge on the nucleation and growth can be considered. The simulated results are in good agreement with experiment results.

Study on Effect of Gd (III) Speciation on Ca (II) Speciationin Human Blood Plasma by Computer Simulation

Ca (II) speciation and effect of Gd (III) speciation on Ca (II) speciation in human blood plasma were studied by computer simulation. [CaHCO3](-) is a predominant compound species of Ca (II). Gd (III) can compete with Ca (II) for biological molecules. The presence of Gd (III) results in a increase of concentration of free Ca (II) and a decrease of concentration of Ca (II) compounds.

EXPERIMENTAL INVESTIGATION AND COMPUTER SIMULATION ON DYNAMIC BUCKLING BEHAVIOR OF LIQUID-FILLED CYLINDRICAL SHELLS UNDER AXIAL IMPACT

This article reports an experimental investigation on the axial impact buckling of thin metallic cylindrical shells fully filled with water. Low velocity impact tests are carried out by DHR-9401 drop hammer rig. The whole process of dynamic buckling is simulated using LS-DYNA computer code. The consistency between experimental observation and numerical simulation is quite satisfactory. The investigation indicates that quite high internal hydrodynamic pressure occurs inside the shell during the impact process. Under the combined action of the high internal pressure and axial compression plastic buckling occurs easily in the thin-walled shells and buckling modes take on regular and axisymmetric wrinkles.

THEORETICAL PREDICTION OF TOOL-CHIP CONTACT LENGTH IN ORTHOGONAL METAL MACHINING BY COMPUTER SIMULATION

A method for determination of tool-chip contact length is theoreticallypresented in orthogonal metal machining. By using computer simulation and based on the analyses ofthe elastro-plastic deformation with lagrangian finite element method in the deformation zone, theaccumulated representative length of the low layer, the tool-chip contact length of the chipcontacting the tool rake are calculated, experimental studies are also carried out with 0.2 percentcarbon steel. It is shown that the tool-chip contact lengths obtained from computer simulation havea good agreement with those of measured values.

STUDY ON SINGULAR CONFIGURATIONS AND COMPUTER SIMULATION OF 6R ROBOT

When robot is at singular configuration, the limited hand velocity wouldrequire some joints with infeasible speeds so as to lead unsafely of the system. A method of solvingthe approximate velocity of joint near singular configuration point by adding damped vector isproposed and a modified algorithm is provided. With the analysis of J^(-1) the singularconfigurations of 6R robot are divided into structure boundary singularity , boundary singularity ,inner singularity and wrist singularity. The conditions of singularities of the robot have beenascertained. The computer simulations of the singularities of the robot are developed, which havemany advantages over previous description methods of the singular configurations of robot. With thehelp of boundary singularity analysis, a application in welding trajectory planning checking of therobot has been carried out and the simulation result proved visualized and useful.

COMPUTER SIMULATION OF CONTINUOUS ELECTROMAGNETIC STIRRING FOR MAKING RHEOLOGIC SEMI-SOLID SLURRY OF ZL112Y ALUMINUM ALLOY

To realize the technology of fabricating the rheologic semi-solid slurry of ZL112Y aluminum alloy via continues electromagnetic stirring process, ANSYS software was used to simulate electromagnetic force field and fluid velocity field in the alloy melt in a crucible tube in three coils. In the first section of the paper, eletromagnetic force field and fluid velocity field caused by single coil were simulated. The result of this simulation gives an average velocity of 3.2 cm/s and it is called critical velocity because a fluid velocity over it will cause a fine and spherical structure of solid primary a in a semi-solid melt. And, from this result, a reasonable temperature of semi-solid of the alloy and an electrical current intensity were established. The electrical current intensity of the result of this simulation corresponded to the current intensity used in a practice experiment, in which the primary α was obviously refined and sphericized. Based on this simulation of single coil electromagnetic stirring, in the second section of the paper, eletromagnetic force field and fluid velocity field caused by three coils were simulated. The result of the simulation shows that, 1） there is a semi-solid zone of 32 mm from bottom of the crucible tube to the upper; 2） the electrical current intensities of three coils of 400 A, 600 A, and 400 A, which were set to top range, middle range and bottom range of the tube, respectively, were the optimum parameters of electromagnetic current intensity under the condition of this investigation; and 3） under effect of these electromagnetic current intensity, the fluid velocities of the melt in the tube were 6.3 cm/s in top range, 3.75 cm/s in middle range, and 3.9 cm/s in bottom range of it, respectively.

Studies on Insoluble Species of Gd(Ⅲ)in Human Blood Plasma by Computer Simulation

The insoluble species of Gd ( Ⅲ ) in human blood plasma were investigated by computer simulation. The distribution of the Gd(Ⅲ ) species was obtained. It was found that most of the Gd( Ⅲ ) ions were bound to phosphate to form precipitate GdPO4 at the concentration of 1. 000 10-7 mol/L and when the concentration of the Gd (Ⅲ ) increased to 3. 750 X 10-4 mol/L, in excess of the concentration of phosphate, the Gd ( Ⅲ ) ions were bound to carbonate to form another kind of precipitate, Gd2(CO3)3.

Computer simulation of evacuation in underground coal mines

In order to study the evacuation behavior of miners during accidents,we analyzed the rational layout of a safe chamber,and improved evacuation efficiency.A visual model of evacuation was developed and used to simulate the evacuation process of mines,given their special underground environments.In our simulation,the working faces of a coal mine and nearby tunnels were divided into 0.5 m×0.5 m grids to reflect the location of occupants and obstacles.Based on a "flow potential of the occupant",we determined the direction of movement and routes of occupants.In the model,evacuation speed changed as a function of crowd density,with an average speed of 1.30 m/s.The model also takes into account detection time of the disaster and the personnel response time.Evacuation time,exit flow rate and evacuation path were obtained by simulation.The results indicate that using simulation technology can present a more visual evacuation process and show the behavior of occupants.Our establishment of a mine safety evacuation system has merit as reference value.

Computer simulation of the air flow distribution in goaf regarding the use of inert gases and chemical agents

This paper presents the use of a computer method of the ventilation process simulation for the analysis of the flow distribution of air and gases in the area of wall mining work and the adjacent goaf.In workings and goaf,the complex issue of the formation of a gaseous atmosphere under variable ventilation conditions and an existing fire hazard level,with the possibility of feeding goaf with an additional carbon dioxide flux as the inertizing agent is considered.Some examples of the simulation of feeding goaf with carbon dioxide illustrating the different patterns of the distribution of the goaf atmosphere gases concentration,said distribution patterns being gas supply place dependent,have been presented.In addition,the impact of the additional sealing of goaf on the distribution level of the concentration of gases,the said sealing made from the wall side with chemical agents has also been considered.The capabilities of the VentGoaf computer simulation program,being the basis for our calculations,enable consideration of the use of the inert gases supplied to the goaf depending on: the location of the gas feeding the pipe outlet,tightness of the fire field,fire centre location,and spatial situation of the mined wall.It has been found that fire prevention elements,such as chemical sealing agents,are of great impact on the effectiveness of fire prevention.

Computer Simulation of Gd(III) Speciation in Human Interstitial Fluid

The speciation and distribution of Gd(III) in human interstitial fluid was studied by computer simulation. Meantime artificial neural network was applied to the estimation of log ?values of complexes. The results show that the precipitate species, GdPO4 and Gd2(CO3)3, are the predominant species. Among soluble species, the free Gd(III), [Gd(HSA)] , [Gd(Ox)] and then the ternary complexes of Gd(III) with citrate are main species and [Gd3(OH)4] becomes the predominant species at the Gd(III) total concentration of 2.2?0-2mol/L.

COMPUTER SIMULATION OF EFFECT OF ORIENTATION DIFFERENCE ON MECHANICAL PROPERTIES OF BICRYSTALLINE SPECIMENS

Based on the experimental results of the work-hardening processes of single crystals,the ac- commodation processes of polycrvstal deformation and the assumption of idealized polycrystal,the stress-strain relation of elasto-plastic deformation crystal was derived.The effect of orientation difference on the mechanical properties of the bicrvstalline specimens of aluminum was simulated by means of the finite element method(FEM)of elasto-plastic crystal.The results are in good agreement with the experimental results made by Clark and Chalmers in 1954.

New filling system design for bolster casting and computer simulation

The new filling system is smooth filling without gas gap. It works well in avoiding the generation of defects such as porosity and inclusion. The pouring basin, sprue, runner and the gate of the bolster casting were designed according to the principle of the new filling system. The filling and solidifciation process of the bolster casting were also simulated. It was found that the filling process was smooth, and air entrapment and shrinkage were avoided. Finally, a further validation of the new filling system of bolster casting was carried out in a foundry.

Computer simulation on the controlled cooling of 82B high-speed rod

A modified temperature-phase transformation field coupled nonlinear mathematical model was made and used in computer simulation on the controlled cooling of 82B high-speed rods. The surface temperature history and volume fraction of pearlite as well as the phase transformation history were simulated by using the finite element software Marc/Mentat. The simulated results were compared with the actual measurement and the agreement is good which can validate the presented computational models.