Co-Frequency Interference Analysis and Avoidance Between NGSO Constellations: Challenges, Techniques, and Trends

In recent years,as giant satellite constellations grow rapidly worldwide,the co-existence between constellations has been widely concerned.In this paper,we overview the co-frequency interference(CFI)among the giant non-geostationary orbit(NGSO)constellations.Specifically,we first summarize the CFI scenario and evaluation index among different NGSO constellations.Based on statistics about NGSO constellation plans,we analyse the challenges in mitigation and analysis of CFI.Next,the CFI calculation methods and research progress are systematically sorted out from the aspects of interference risk analysis framework,numerical calculation and link construction.Then,the feasibility of interference mitigation technologies based on space,frequency domain isolation,power control,and interference alignment mitigation in the NGSO mega-constellation CFI scenario are further sorted out.Finally,we present promising directions for future research in CFI analysis and CFI avoidance.

Well interference evaluation considering complex fracture networks through pressure and rate transient analysis in unconventional reservoirs

Severe well interference through complex fracture networks(CFNs)can be observed among multi-well pads in low permeability reservoirs.The well interference analysis between multi-fractured horizontal wells(MFHWs)is vitally important for reservoir effective development.Well interference has been historically investigated by pressure transient analysis,while it has shown that rate transient analysis has great potential in well interference diagnosis.However,the impact of complex fracture networks(CFNs)on rate transient behavior of parent well and child well in unconventional reservoirs is still not clear.To further investigate,this paper develops an integrated approach combining pressure and rate transient analysis for well interference diagnosis considering CFNs.To perform multi-well simulation considering CFNs,non-intrusive embedded discrete fracture model approach was applied for coupling fracture with reservoir models.The impact of CFN including natural fractures and frac-hits on pressure and rate transient behavior in multi-well system was investigated.On a logelog plot,interference flow and compound linear flow are two new flow regimes caused by nearby producers.When both NFs and frac-hits are present in the reservoir,frac-hits have a greater impact on well#1 which contains frac-hits,and NFs have greater impact on well#3 which does not have frac-hits.For all well producing circumstances,it might be challenging to see divergence during pseudosteady state flow brought on by frac-hits on the logelog plot.Besides,when NFs occur,reservoir depletion becomes noticeable in comparison to frac-hits in pressure distribution.Application of this integrated approach demonstrates that it works well to characterize the well interference among different multi-fractured horizontal wells in a well pad.Better reservoir evaluation can be acquired based on the new features observed in the novel model,demonstrating the practicability of the proposed approach.The findings of this study can help for better evaluating well interference degree in multi-well systems combing PTA and RTA,which can reduce the uncertainty and improve the accuracy of the well interference analysis based on both field pressure and rate data.

Application of Wavelet Analysis toInterference Elimination for Geochemical Hydrocarbon Exploration

Interference in the data of geochemical hydrocarbon exploration is a large obstacle for anomaly recognition. The multiresolution analysis of wavelet analysis can extract the information at different scales so as to provide a powerful tool for information analysis and processing. Based on the analysis of the geometric nature of hydrocarbon anomalies and background, Mallat wavelet and symmetric border treatment are selected and data pre-processing (logarithm-normalization) is established. This approach provide good results in Shandong and Inner Mongolia, China. It is demonstrated that this approach overcome the disadvantage of backgound variation in the window (interference in window), used in moving average, frame filtering and spatial and scaling modeling methods.

Wavelet analysis method of harmonics and electromagnetic interference in coal mines

In this study we propose an analytical method based on orthogonal wavelet transforms for detecting harmonic noise and Electromagnetic Interference (EMI) from power supply systems and equipment in coal mines. The method will separate interference from signals through wavelet packet decomposition and then accomplish wavelet packet synthesis towards decomposition results after filtering, to remove harmonic noise and electromagnetic interference. Detailed simulation experiments are presented to study power harmonics and Electrical Fast Transient Burst (EFT/B) interference and to validate the effectiveness of our proposed method. The experimental results show that the proposed method, suitable for mutant and non-stationary signal detection, can accurately analyze harmonic interference and EMI in coal mines, as well as establish EMI source models and perform underground Electromagnetic Compatibility (EMC) prediction analyses.

Interference analysis and novel fractional frequency reuse scheme in LTE networks

Inter-cell interference (ICI) mitigation is always a challenge issue in LTE system. In this paper, several common interference parameters are firstly analyzed for both cell edge users and center users, and then a novel fractional frequency reuse (FFR) architecture based on interference avoidance scheme coupled with power control is proposed to solve the problem of interference management in multi-cell LTE environment. The scheme divides the whole sub-carriers into three groups orthogonally. One is allocated to cell edge users, while another two are assigned to cell center users with different transmitter power. Then a parameter named interference avoidance factor (IAF) is defined to avoid ICI and adjust the number of allocated sub-carriers to match the number of users. The parameter also takes weight factor and fairness factor into consideration. The simulation results show the proposed scheme can improve the performance of cell edge users obviously.

Analysis of Multipath and CW Interference Effects on GNSS Receivers with EMLP Discriminator

Multipath and continuous wave (CW) interference may cause severe performance degradation of global navigation satellite system (GNSS) receivers. This paper analyzes the code tracking performance of early-minus-late power (EMLP) discriminator of GNSS receivers in the presence of multipath and CW interference. An analytical expression of the code tracking error is suggested for EMLP discriminator, and it can be used to assess the effect of multipath and CW interference. The derived expression shows that the combined effects include three components: multipath component;CW interference component and the combined component of multipath and CW interference. The effect of these components depends on some factors which can be classified into two categories: the receiving environment and the receiver parameters. Numerical results show how these factors affect the tracking performances. It is shown that the proper receiver parameters can suppress the combined effects of multipath and CW interference.

Independent Component Analysis Based Blind Adaptive Interference Reduction and Symbol Recovery for OFDM Systems

To overcome the inter-carrier interference （ICI） of orthogonal frequency division multiplexing （OFDM） systems subject to unknown carrier frequency offset （CFO） and multipath, this paper develops a blind adaptive interference suppression scheme based on independent component analysis （ICA）. Taking into account statistical independence of subcarriers＇ signals of OFDM, the signal recovery mechanism is investigated to achieve the goal of blind equalization. The received OFDM signals can be considered as the mixed observation signals. The effect of CFO and multipath corresponds to the mixing matrix in the problem of blind source separation （BSS） framework. In this paper, the ICA- based OFDM system model is built, and the proposed ICA-based detector is exploited to extract source signals from the observation of a received mixture based on the assumption of statistical independence between the sources. The blind separation technique can increase spectral efficiency and provide robustness performance against erroneous parameter estimation problem. Theoretical analysis and simulation results show that compared with the conventional pilot-based scheme, the improved performance of OFDM systems is obtained by the proposed ICA-based detection technique.

An Analysis of Interference as a Source for Diffraction

An analysis is made of interference of two plane waves which in turn give rise to subsequent diffraction phenomena. This is done using two different approaches. One of them is straight forward but is difficult to interpret. The second is less conventional but more intuitive thus giving more insight into the process. The geometry is kept very simple to focus on the process itself. Both approaches give rise to the same results thus offering a choice in tackling such prob-lems.

Multiple transformation analysis for interference separation in TDCS

Various types of interference signals limit the practical application of transform domain communication systems(TDCSs)in the severe electromagnetic field,an orthogonal basis learning method of transformation analysis(OBL-TA)is proposed to effectively address the problem of obtaining an optimal transform domain based on sparse representation.Then,the sparse availability is utilized to obtain the optimal transformation analysis by the iterative methods,which yields the sparse representation for transform domain(SRTD)in unrestricted form.In addition,the iterative version of SRTD(I-SRTD)in unrestricted form is obtained by decomposing the SRTD problem into three sub-problems and each sub-problem is iteratively solved by learning the best orthogonal basis.Furthermore,orthogonal basis learning via cost function minimization process is conducted by stochastic descent,which is assured to converge to a local minimum at least.Finally,the optimal transformation analysis is developed by the effectiveness of different transform domains according to the accuracy of the sparse representation and an optimal transformation analysis separately(OPTAS)is applied to the synthesized signal forms with conic alternatives,dualization,and smoothing.Simulation results demonstrate that the superiorities of the proposed methods achieve the optimal recovery and separation more rapidly and accurately than conventional methods.

An Analysis of Mutual Interference in Radar Systems Using Dual-Band (Ka / X) Antennas

An analysis of mutual interfering sources on RF systems using dual-band (Ka / X) radar is presented. The purpose of this paper is to improve operational performance of the system from the point of view of EMC design. The experimental dual-band antenna system have decreased the disturbing effects of most mutual interfering sources.

Relay selection region and system performance analysis for interfered cooperative ad-hoc networks

The performance of interfered cooperative ad-hoc networks is analyzed by stochastic geometry analysis and a selection region of relay is presented. First, assuming that the distribution of nodes in the random network follows the Poisson point process （PPP）, a closed-form expression of the outage probability is derived for the best relay selection （BRS） scheme. Secondly, the capacity of the network is presented for this scheme. Finally, a performance factor is defined to evaluate the performance gain obtained from the BRS. By using this factor, a relay selection region is found to guarantee the performance gain from the BRS. The analysis and simulation results show that the performance of the BRS not only depends on the densities of source nodes and relay nodes but also on the factors of networks such as the path loss factor and the decoding threshold. And the BRS has a greater advantage than direct transmission （DT） in hush environments such as the long transmission distances, much interference and the high decoding thresholds.

An Investigation of the Effects of Thermal Interference between Adjacent Nitinol Spring Actuators in a Tactile Display

Over the years, there has been increased research interest in the application of Nitinol as an actuator, due to its shape memory behaviour, simplicity, high power-to-weight ratio, compactness, and extreme high fatigue resistance to cyclic motion, and noiseless operation. Nitinol has found application in tactile displays which reproduce tactile parameters such as texture and shape, depending on the application. This paper presents the effects of thermal interference between adjacent Nitinol spring actuators in a tactile display. The tactile display is made of a 3 by 3 pin array whose spatial resolution was varied from 4 mm to 6 mm in steps of 1 mm while a current of 1.5 A was used to actuate 8 of the springs, and the centre spring was left unactivated to observe the thermal effects on it due to the heat gradient formed. A Finite Element (FE) model was developed using COMSOL Multiphysics and the results were further verified through experimentation. In both cases, there was visible thermal interference between actuators. The increase in spatial resolution saw a decrease in thermal interference by 12.7%. Using a fan to introduce forced convection, reduced the thermal interference in the simulation by 20% and during experimentation by 11%. The results of this research indicate a spatial resolution of 6 mm reduced the thermal inference to a negligible rate. However, thermal interference could not be eliminated with these two methods.

Estimation of co-channel interference between cities caused by ducting and turbulence

With the rapid development of the fifth-generation(5 G)mobile communication technology,the application of each frequency band has reached the extreme,causing mutual interference between different modules.Hence,there is a requirement for detecting filtering and preventing interference.In the troposphere,over-the-horizon propagation occurs in atmospheric ducts and turbulent media.The effects of both ducting and turbulence can increase the probability of occurrence of long-distance co-channel interference(CCI),in turn,severely affecting the key performance indicators such as system access,handover and drop.In the 5 G era,to ensure communication channels and information security,CCI must be reduced.This paper introduces a scattering parabolic equation algorithm for calculating signal propagation in atmospheric ducts on irregular terrain boundaries.It combines Hitney’s radio physical optical model and Wagner’s nonuniform turbulent scattering model for calculating the tropospheric scattering in an evaporation duct or a surface-based duct.The new model proposes a tropospheric scattering parabolic equation algorithm for various tropospheric duct environments.Finally,as a specific case,the topographical boundaries between several cities in the East China Plain were considered,and the over-the-horizon propagation loss was simulated for various ducting and turbulent environments.The simulation results were used to evaluate whether CCI would occur between cities in a specific environment.

Online Investigation of Optical Properties and Craze Propagation of Drawn Polypropylene Fiber by Using Interferometric Image Analysis

Pluta polarizing interference microscope was used to follow the crazing that occur on the surface of stretched polypropylene fibres at different drawing conditions. The samples were stretched until crazing initiated, and then craze propagation was monitored as a function of drawing speed and test temperature. The effect of craze dimension on their propagation velocity was taken into account. Three-dimensional birefringence profile for crazed polypropylene fibre has been demonstrated to investigate the birefringence of crazed fibre at different test times for fixed drawing speed value. Also the mean birefringence values of crazed polypropylene fibres were calculated and the results showed that, these values increased with the areal craze density. Video images were used to calculate the craze velocity. Optical micrographs and microinterferograms were presented for demonstrations.

Study of inter-well interference in shale gas reservoirs by a robust production data analysis method based on deconvolution

In order to overcome the defects that the analysis of multi-well typical curves of shale gas reservoirs is rarely applied to engineering,this study proposes a robust production data analysis method based on deconvolution,which is used for multi-well inter-well interference research.In this study,a multi-well conceptual trilinear seepage model for multi-stage fractured horizontal wells was established,and its Laplace solutions under two different outer boundary conditions were obtained.Then,an improved pressure deconvolution algorithm was used to normalize the scattered production data.Furthermore,the typical curve fitting was carried out using the production data and the seepage model solution.Finally,some reservoir parameters and fracturing parameters were interpreted,and the intensity of inter-well interference was compared.The effectiveness of the method was verified by analyzing the production dynamic data of six shale gas wells in Duvernay area.The results showed that the fitting effect of typical curves was greatly improved due to the mutual restriction between deconvolution calculation parameter debugging and seepage model parameter debugging.Besides,by using the morphological characteristics of the log-log typical curves and the time corresponding to the intersection point of the log-log typical curves of two models under different outer boundary conditions,the strength of the interference between wells on the same well platform was well judged.This work can provide a reference for the optimization of well spacing and hydraulic fracturing measures for shale gas wells.

Effect of the Cutter Parameters and Machining Parameters on the Interference in Gear Slicing

Current researches have not yet found the effect law of the cutter parameters and machining parameters on the interference in gear slicing, the interference between the cutter and machined gear often happens because the appropriate cutter parameters and machining parameters cannot be set, which reduces the gear machining accuracy. The relative position between the major flank face and edge-sweeping surface, distribution law of the interference area in forming process of edge-sweeping surface, and effect law of relative positions among edge-sweeping surfaces on the interference are studied by graphical analysis. The effect law of the cutter parameters and machining parameters on the interference is found. The effect law shows that the interference in gear slicing can be controlled when the relief angle measured on the top edge and feed of every rotation are chosen respectively larger than 9~ and smaller than 0.15 mrn/r. An internal helical gear is sliced with the spur slice cutter and the cutter parameters and machining parameters are set based on above the effect law. The machined gear is measured in Gear Measuring Center and the detection result shows that the comprehensive accuracy reaches GB/T Class 7, where some reach GB/T Class 6. The result can meet the gear machining accuracy requirement and shows that the effect law found is valid. The problem of the interference in gear slicing is solved and the gear machining accuracy can be improved.

TDOA estimation of dual-satellites interference localization based on blind separation

The time difference of arrival(TDOA)estimation plays a crucial role in the accurate localization of the satellite interference source.In the dual-satellites interference source localization system,the target signal from the adjacent satellite is likely to be interfered by the normal communication signal with the same frequency.Therefore,the signal to noise ratio(SNR)of the target signal would become too low,and the TDOA estimation through cross-correlation processing would be unreliable or even unattainable.This paper proposes a technique based on blind separation to solve the co-channel interference problem,where separation of the mixed signal can be carried out by the particle filter(PF)algorithm.The experimental results show that the proposed method could achieve more accurate TDOA estimation.The measured data obtained by using the software radio platform at 915 MHz and 2 GHz respectively verify the effectiveness of the proposed method.

Cluster-Based Interference-Free MAC Protocol with Load Aware in Software Defined VANET

In order to reduce the interference,a novel,cluster-based medium access control(MAC)protocol with load aware for VANETs is proposed in this paper.First,all vehicles on roads are grouped into stable clusters in the light of their direction,number of neighbors,link reliability,and traffic load.By utilizing the advantages of centralized control in software defined VANETs(SDVN),cluster stability can be maintained in real-time.Second,a contention-free MAC mechanism composed of inter-cluster multi-channel allocation and intra-cluster dynamic TDMA frame allocation is proposed to prevent co-channel interference and hidden terminal interference.Simulation results show that the proposed protocol outperforms some existing protocols in cluster stability,delivery ratio,throughput and delay performance.

Reverse Genetic Analysis of Transcription Factor Os Hox9, a Member of Homeobox Family, in Rice

Homeobox transcription factors participate in the growth and development of plants by regulating cell differentiation, morphogenesis and environmental signal response. To reveal the functions of these transcription factors in rice, we constructed the RNAi vectors of OsHox9, a member of homeobox family, and analyzed the function of OsHox9 using reverse genetics. The plant height and tillering number of RNAi transgenic plants decreased compared with those of wild-type plants. Reverse transcdption-polymerase chain reaction analysis showed that OsHox9 expression reduced in the transgenic plants with phenotypic variance, whereas that in the transgenic plants without phenotypic variance was similar to that in the wild-type plants. This result suggests that the phenotypes of the transgenic plants were caused by RNAi effects. The tissue-specificity of OsHox9 expression indicated that it was expressed in different organs, with high expression in stem apical medstem and young panicles. Subcellular location of OsHox9 demonstrated that it was localized on the cell membrane.

RELIABILITY ANALYSIS FOR AN AERO ENGINE TURBINE DISK UNDER LOW CYCLE FATIGUE CONDITION

Reliability analysis methods based on the linear damage accumulation law (LDAL) and load-life interference model are studied in this paper. According to the equal probability rule, the equivalent loads are derived, and the reliability analysis method based on load-life interference model and recurrence formula is constructed. In conjunction with finite element analysis (FEA) program, the reliability of an aero engine turbine disk under low cycle fatigue (LCF) condition has been analyzed. The results show the turbine disk is safety and the above reliability analysis methods are feasible.