Capture efficiency of coal/biomass co-combustion ash in an electrostatic field

Ash samples from corn stalk and coal co-fired at 0%,5%,10%,15%,20%,and 100%biomass were collected by a 4-stage wire-pipe type electrostatic precipitator (ESP),and the ratio of 14C/12C in ash samples from the 0%,20%,and 100% co-firing scenarios were measured by an accelerator mass spectrometer.The differential capture efficiency in electrostatic fields for coal ash,coal/biomass co-combustion ash (co- ash),and pure biomass ash was studied separately based on the ratio 14C/12C.Other factors that may influence capture efficiency were analyzed,including microscopic morphology,resistivity,dust density, and particle size distribution.The results indicate that co-ash may be efficiently captured by ESP,while pure biomass ash could not.Co-ash capture was mainly concentrated in the first two electrostatic fields in the lab-scale ESP,and the overall capture efficiency exceeded 90%.Biomass addition decreased the resistivity of co-ash,and enhanced its surface adsorption capacity to form agglomerates,facilitating the capture of co-ash.The capture efficiency of coal ash in co-ash was higher than that of pure coal ash in the first electrostatic field of the ESP.Co-firing biomass can aid the removal of both coal ash and biomass ash when using an ESP.

High-temperature corrosion of sintered RE_(2)Si_(2)O_(7)(RE=Yb and Ho)environmental barrier coating materials by volcanic ash

Rare-earth silicates are promising environmental barrier coatings(EBCs)that can protect SiC_(f)/Si C_(m)substrates in next-genera tion gas turbine blades.Notably,RE_(2)Si_(2)O_(7)(RE=Yb and Ho)shows potential as an EBC due to its coefficient of thermal expansion(CTE)compatible with substrates and high resistance to water vapor corrosion.The target operating temperature for next-generation tur bine blades is 1400°C.Corrosion is inevitable during adhesion to molten volcanic ash,and thus,understanding the corrosion behavior o the material is crucial to its reliability.This study investigates the high-temperature corrosion behavior of sintered RE_(2)Si_(2)O_(7)(RE=Yb and Ho).Samples were prepared using a solid-state reaction and hot-press method.They were then exposed to volcanic ash at 1400°C for 224,and 48 h.After 48 h of exposure,volcanic ash did not react with Yb_(2)Si_(2)O_(7)but penetrated its interior,causing damage.Meanwhile Ho_(2)Si_(2)O_(7)was partially dissolved in the molten volcanic ash,forming a reaction zone that prevented volcanic ash melts from penetrating the interior.With increasing heat treatment time,the reaction zone expanded,and the thickness of the acicular apatite grains increased The Ca:Si ratios in the residual volcanic ash were mostly unchanged for Yb_(2)Si_(2)O_(7)but decreased considerably over time for Ho_(2)Si_(2)O_(7).Th Ca in volcanic ash was consumed and formed apatite,indicating that RE^(3+)ions with large ionic radii(Ho>Yb)easily precipitated apatit from the volcanic ash.

Mechanism study of Cu(Ⅱ) adsorption from acidic wastewater by ultrasonic-modified municipal solid waste incineration fly ash

High concentrations of copper ions(Cu(Ⅱ)) in water will pose health risks to humans and the ecological environment. Therefore, this study aims to utilize ultrasonic-cured modified municipal solid waste incineration(MSWI) fly ash for Cu(Ⅱ) adsorption to achieve the purpose of “treating waste by waste.” The effects of p H, adsorption time, initial concentration, and temperature on the modified MSWI fly ash’s adsorption efficiency were systematically studied in this article. The adsorption performance of the modified MSWI fly ash can be enhanced by the ultrasonic modification. At pH = 2, 3 and 4, the adsorption capacity of the modified MSWI fly ash for Cu(Ⅱ) increased by 2.7, 1.9 and 1.2 times, respectively. Furthermore, it was suggested that the adsorption process of the modified MSWI fly ash can be better simulated by the pseudo-second-order kinetic model, with a maximum adsorption capacity calculated by the Langmuir model of 24.196 mg.g-1. Additionally, the adsorption process is spontaneous,endothermic, and chemisorption-dominated from the thermodynamic studies(ΔH and ΔS > 0, ΔG < 0).Finally, the enhanced adsorption performance of the modified MSWI fly ash for Cu(Ⅱ) may be attributed to electrostatic interaction and chelation effects.

A mini review on the separation of Al,Fe and Ti elements from coal fly ash leachate

The electricity demand is increasing rapidly with the development of society and technology.Coal-fired thermal power plants have become one of the primary sources of electricity generation for urbanization.However,coal-fired thermal power plants produce a great amount of by-product coal fly ash every year.Coal fly ash disposal in landfills requires a sizable space and has negative environmental impacts.Therefore,it is crucial to develop new technologies and methods to utilize this enormous volume of solid waste in order to protect the environment.In this review,the fundamental physical and chemical character-istics of coal fly ash are introduced,and afterward the disposal policies and utilization ways of coal fly ash are discussed to gain a comprehensive understanding of the various ways this waste.The leaching of valuable metals in coal fly ash and the extraction of metal elements in leachate under different conditions are also summarized.Furthermore,the possibility of coal fly ash to serve as a supplementary source for mineral resources is analyzed,providing a basis for its extensive use as a raw material in the metal industry in China and worldwide.

Amino acid and mineral digestibility,bone ash,and plasma inositol is increased by including microbial phytase in diets for growing pigs

Background The effect of microbial phytase on amino acid and energy digestibility is not consistent in pigs,which may be related to the phytase dosage or the adaptation length to the diet.Therefore,an experiment was conducted to test the hypotheses that increasing dietary phytase after an 18-day adaptation period:1)increases nutrient and energy digestibility;2)increases plasma P,plasma inositol,and bone ash of young pigs;and 3)demonstrates that maximum phytate degradation requires more phytase than maximum P digestibility.Results Data indicated that increasing inclusion of phytase[0,250,500,1,000,2,000,and 4,000 phytase units(FTU)/kg feed]in corn-soybean meal-based diets increased apparent ileal digestibility(AID)of Trp(quadratic;P<0.05),and of Lys and Thr(linear;P<0.05),and tended to increase AID of Met(linear;P<0.10).Increasing dietary phytase also increased AID and apparent total tract digestibility(ATTD)of Ca and P(quadratic;P<0.05)and increased ATTD of K and Na(linear;P<0.05),but phytase did not influence the ATTD of Mg or gross energy.Concentrations of plasma P and bone ash increased(quadratic;P<0.05),and plasma inositol also increased(linear;P<0.05)with increasing inclusion of phytase.Reduced concentrations of inositol phosphate(IP)6 and IP5(quadratic;P<0.05),reduced IP4 and IP3(linear;P<0.05),but increased inositol concentrations(linear;P<0.05)were observed in ileal digesta as dietary phytase increased.The ATTD of P was maximized if at least 1,200 FTU/kg were used,whereas more than 4,000 FTU/kg were needed to maximize inositol release.Conclusions Increasing dietary levels of phytase after an 18-day adaptation period increased phytate and IP ester degradation and inositol release in the small intestine.Consequently,increasing dietary phytase resulted in improved digestibility of Ca,P,K,Na,and the first 4 limiting amino acids,and in increased concentrations of bone ash and plasma P and inositol.In a corn-soybean meal diet,maximum inositol release requires approximately 3,200 FTU/kg more phytase than that required for maximum P digestibility.

Levels of Polycyclic Aromatic Hydrocarbons (PAHs) in Healthcare Waste Incinerators’ Bottom Ash from Five County Hospitals in Kenya

Health-care waste contains potentially harmful microorganisms and compounds which can infect and affect hospital patients, healthcare workers, the general public and environment. Therefore, management of health care waste requires safe handling, treatment and disposal procedures. While incineration reduces the volume and quantity of waste for final disposal, it leads to the production of fly and bottom ashes laden with toxic incomplete combustion products such as Polycyclic Aromatic Hydrocarbons (PAHs), dioxins, furans and heavy metals. This exposes workers who handle and dispose the bottom ashes, hospital patients, the general public and environment. The goal of this study was to determine the total and individual levels of 16 most prevalent and toxic PAHs. Bottom ash samples were collected from incinerators in five county hospitals in Kenya, namely;Moi-Voi, Narok, Kitale, Makindu and Isiolo. Bottom ash samples were collected over a period of six months from the five hospitals. The samples were then sieved, homogenised and stored at 4°C in amber coloured glass containers. The PAHs were extracted using 30 ml of a hexane-acetone solvent (1:1) mixture by ultrasonication at room temperature (23°C) for 45 minutes. The PAHs were then analyzed with a GC-MS spectrophotometer model (Shimadzu GCMS-QP2010 SE) connected to a computer work station was used for the PAHs analysis. The GC-MS was equipped with an SGE BPX5 GC capillary column (30 m × 0.25 mm × 0.25 μm) for the separation of compounds. Helium was used as the carrier gas at a flow rate of 15.5 ml/minute and 14.5 psi. 1 μl of the sample was injected at 280°C, split mode (10:1). The oven programming was set for a total runtime of 40 minutes, which included: 100°C (2-minute hold);10°C /min rise to 200°C;7°C /min rise to 249°C;3°C /min rise to 300°C (2-minute hold). The interface temperature was set at 290°C. Analysis was done in Selected Ion Monitoring (SIM) mode and the peak areas of each of the PAHs were collected from the chromatograph and used for quantification of the 16 PAHs listed by the U.S. Environmental Protection Agency (EPA) which included, BaA (benz[a]anthracene: 4 rings), BaP (benzo[a]pyrene: 5 rings), BbF (benzo [b]fluoranthene: 5 rings), BkF (benzo[k]fluoranthene: 5 rings), Chr (chrysene: 4 rings), DbA (dibenz[a,h]anthracene: 5 rings), InP (indeno[1,2,3 - cd] pyrene: 6 rings) and Acp (acenaphthene: 3 rings), Acpy (acenaphthylene: 3 rings), Ant (anthracene: 3 rings), BghiP (benzo[g,h,i]perylene: 6 rings), Flu (fluorene: 3 rings), FluA (fluoranthene: 4 rings), Nap (naphthalene: 2 rings), PhA (phenanthrene: 3 rings) and Pyr (pyrene: 4 rings). Ion source-interface temperature was set at 200°C - 250°C. Internal standards from Sigma Aldrich were used in the analysis and the acquired mass spectra data were then matched against the NIST 2014 library [1] [2]. The mean PAHs concentration in the bottom ashes of each hospital varied broadly from 0.001 mg/kg to 0.4845 mg/kg, and the mean total concentration levels of individual PAHs ranged from 0.0072 mg/kg to 1.171 mg/kg. Low molecular weight PAHs (Phenanthrene, Naphthalene and Fluorene) were predominant in all the hospital wastes whereas Kitale and Narok presented the lowest PAHs concentrations and the lowest number of individual PAHs. Moi/Voi recorded the highest total PAHs concentration at 1.3129 ± 0.0023 mg/kg from a total of 11 PAHs being detected from the bottom ash samples. Narok had only three PAHs being detected at very low concentrations of 0.0041 ± 0.00 mg/kg, 0.0076 ± 0.00 mg/kg and 0.012 ± 0.00 mg/kg for phenanthrene, anthracene and chrysene respectively. This study presents hospital incinerator bottom ash as containing detectable levels of both carcinogenic and non-carcinogenic PAHs. Continued unprotected exposure of hospital workers (waste handlers) to the bottom ash PAHs could be hazardous to their health because of their cumulative effect. Preventive measures e.g. the use of Personal protective equipment (PPE) should be prioritised to minimise direct contact with the bottom ash. The study recommends an upgrade on incinerator technology for efficient combustion processes thus for better pollution control.

Fabrication of Silane and Desulfurization Ash Composite Modified Polyurethane and Its Interfacial Binding Mechanism

Polyurethane/desulfurization ash(PU/DA)composites were synthesized using"one-pot method",with the incorporation of a silane coupling agent(KH550)as a"molecular bridge"to facilitate the integration of DA as hard segments into the PU molecular chain.The effects of DA content(φ)on the mechanical properties,thermal stability,and hydrophobicity of PU,both before and after the addition of KH550,were thoroughly examined.The results of microscopic mechanism analysis confirmed that KH550 chemically modified the surface of DA,facilitating its incorporation into the polyurethane molecular chain,thereby significantly enhancing the compatibility and dispersion of DA within the PU matrix.When the mass fraction of modified DA(MDA)reached 12%,the mechanical properties,thermal stability,and hydrophobicity of the composites were substantially improved,with the tensile strength reaching 14.9 MPa,and the contact angle measuring 100.6°.

Synergistic CO_(2) mineralization using coal fly ash and red mud as a composite system

CO_(2) mineralization plays a critical role in the storage and utilization of CO_(2).Coal fly ash(CFA)and red mud(RM)are widely utilized as CO_(2) mineralizers.However,the inert calcium species in CFA limit its carbonation capacity,meanwhile the substantial Ca^(2+)releasing of RM is hindered by a covering layer of calcium carbonate.In this study,CO_(2) mineralization in a composite system of CFA and RM was investigated to enhance the carbonation capacity.Multiple analyzers were employed to characterize the raw materials and resulting mineralization products.The results demonstrated that a synergistic effect existed in the composite system of CFA and RM,resulting in improving CO_(2) mineralization rate and efficiency.The produced calcium carbonate was ectopically attached the surface of CFA in the composite system,thus slowing down its coverage on the surface of RM.This phenomenon facilitated further releasing Ca^(2+)from the internal RM,thereby enhancing CO_(2) mineralization efficiency.Meanwhile,the inclusion of RM significantly improved the alkalinity of the composite system,which not only promoted the dissolution of Ca^(2+)of the inert CaSO_(4)(H_(2)O)_(2) in CFA,but also accelerated CO_(2) mineralization rate.The investigation would be beneficial to CO_(2) mineralization using industrial solid wastes.

Solvothermal synthesis and adsorption performance of layered boehmite using aluminum chloride and high-alumina fly ash

High alumina fly ash(FAHAl)is a kind of bulk solid waste unique to China,whose availability of high-value aluminum and the threat to the environment makes its high-value utilization urgent.In this work,the alumina containing leaching solution obtained from Na_(2)CO_(3) roasting and HCl leaching of FAHAl was used as the mother liquor to prepare layered boehmite in situ.The preparation process with AlCl_(3) as the raw material was also compared.The formation process and mechanism of boehmite,the choice of solvent,along with the adsorption capability of Congo red were analyzed by X-ray diffraction,scanning electron microscopy,Fourier transform infrared spectroscopy,Brunauer-Emmett-Teller method and adsorption experiments.Results showed that during the preparation of layered boehmite,the precursor Al(OH)_(3) from the reaction of Al^(3+) and OH-is transformed into boehmiteγ-AlOOH.The existence of ethanol is beneficial to regulate and promote the growth of boehmite crystal effectively.When water and ethanol are mixed with a volume ratio of 2:1 and used as the solvent,the maximum specific surface area of the boehmite is obtained at 135.7 m^(2)·g^(-1),and 99.16%of Congo red can be absorbed after 10 min when AlCl3 is used as a raw material.As purified leaching solution is used as the mother liquid,the crystallinity of boehmite decreases slightly when the pH value decreases from 12.5 to 11.When pH is 11,the removal efficiency of Congo red reaches a maximum of 72.25%.This process not only achieves the extraction of aluminum and high-value utilization of FAHAl but also provides a thought to prepare layered boehmite with adsorption properties.

Does ash dieback affect the reproductive ecology of Fraxinus excelsior L.?

Forest tree species reproduction is a key factor in maintaining the genetic diversity of future generations and the stability of forest ecosystems.The ongoing ash dieback disease could affect the reproductive ecology of Fraxinus excelsior L.and have a major impact on the quantity and quality of pollen and seeds.In this study,we investigated pollen production and viability of pollen and seeds of ash trees with different health status from 2018 to 2022.Inflorescences were collected from 105 trees(pollen production),pollen from 125 trees(pollen viability),and seeds from 53 trees(seed quality)in two seed orchards and in one floodplain forest in southern Germany.Not all parameters were examined at every site every year.The average pollen production per tree was estimated at 471.2±647.9 billion pollen grains.In addition,we found that a high number of inflorescences did not equate to high pollen production per inflorescence.Pollen production of healthy and diseased trees did not differ significantly,although only 47%of severely diseased male trees(vs.72%for healthy trees)produced flowers.With regards to pollen viability,the TTC test showed an average viability of 73%±17%.Overall,there was a slight tendency for diseased trees to have less viable pollen.However,a significant difference could only be calculated for trees in the floodplain forest.The percentage of germinable seeds in 2018 was 38%in the floodplain forest and 57%in one of the seed orchards.The percentage of viable seeds(TTC test)ranged from 17 to 22%in the orchards in 2020.Non-viable seeds were usually heavily infested by insects.In general,seed quality was not significantly different between healthy and diseased trees.Our results indicate that ash dieback affects flower formation and pollen viability but not pollen production or seed quality.Nevertheless,the fact that hardly any flowering was observed,especially for trees that were seriously affected,suggests a negative effect of ash dieback on reproductive performance.Thus,severely diseased trees will transfer their genes to a smaller extent to the next generation.

Experimental study on the activation of coal gasification fly ash from industrial CFB gasifiers

Coal gasification fly ash(CGFA)is an industrial solid waste from the coal circulating fluidized bed(CFB)gasification process,and it needs to be effectively disposed to achieve sustainable development of the environment.To realize the application of CGFA as a precursor of porous carbon materials,the physicochemical properties of three kinds of CGFA from industrial CFB gasifiers are analyzed.Then,the activation potential of CGFA is acquired via steam activation experiments in a tube furnace reactor.Finally,the fluidization activation technology of CGFA is practiced in a bench-scale CFB test rig,and its advantages are highlighted.The results show that CGFA is characterized by a high carbon content in the range of 54.06%–74.09%,an ultrafine particle size(d50:16.3–26.1 μm),and a relatively developed pore structure(specific surface area SSA:139.29–551.97 m^(2)·g^(-1)).The proportion of micropores in CGFA increases gradually with the coal rank.Steam activation experiments show that the pore development of CGFA mainly includes three stages:initial pore development,dynamic equilibrium between micropores and mesopores and pore collapse.The SSA of lignite fly ash(LFA),subbituminous fly ash(SBFA)and anthracite fly ash(AFA)is maximally increased by 105%,13%and 72%after steam activation;the order of the largest carbon reaction rate and decomposition ratio of steam among the three kinds of CGFA is SBFA>LFA>AFA.As the ratio of oxygen to carbon during the fluidization activation of LFA is from 0.09 to 0.19,the carbon conversion ratio increases from 14.4%to 26.8%and the cold gas efficiency increases from 6.8%to 10.2%.The SSA of LFA increases by up to 53.9%during the fluidization activation process,which is mainly due to the mesoporous development.Relative to steam activation in a tube furnace reactor,fluidization activation takes an extremely short time(seconds)to achieve the same activation effect.It is expected to further improve the activation effect of LFA by regulating the carbon conversion ratio range of 27%–35%to create pores in the initial development stage.

Performance evaluation of laterite soil embankment stabilized with bottom ash,coir fiber,and lime

In tropical regions,heavy rainfall induces erosion and shallow landslides on road embankments.Cement-based stabilization methods,common in these regions,contribute to climate change due to their high carbon footprint.This study explored the potential application of coir fiber-reinforced laterite soil-bottom ash mixtures as embankment materials in the tropics.The objective is to enhance engineered embankment slopes'erosion resistance and stability while offering reuse options for industrial byproducts.This study examined various mix designs for unconfined compressive strength(UCS)and permeability,utilizing 30%bottom ash(BA)and 1%coir fiber(CF)with varying sizes ranging from 10 to 40 mm,6%lime,and laterite soil(LS),followed by microstructural analyses.The results demonstrate that the compressive strength increases as the CF length increases to 25 mm.In contrast,permeability increases continuously with increasing CF length.Lime-treated mixtures exhibit superior short-and long-term strength and reduce permeability owing to the formation of cementitious materials,as confirmed by microstructural analyses.A lab-scale slope box was constructed to evaluate the surface erosion of the stabilized laterite soil embankment.Based on the rainfall simulation results,the LS-BA-CF mixtures show better resistance to erosion and deformation compared to untreated LS,especially when lime is added to the top layer.This study provides insights into a sustainable and cost-effective approach for slope stabilization using BA and CF,offering a promising solution for tropical regions susceptible to surface erosion and landslides.

Study on Fly Ash Based Porous Ceramsite as Biological Filter Media

Using fly ash as a raw material,porous ceramic particles with an apparent density of 1.21 g/cm^(3),a visible porosity of 51.03%,and a specific surface area of 4.26 m^(2)/g were prepared and used as biofilter materials for wastewater treatment.Through SEM,XRD analysis,and heavy metal leaching analysis,it was found that porous ceramsite were porous materials with rough surfaces.After calcination,the newly formed mineral was silicate calcium feldspar.The heavy metal concentration in the leaching solution of porous ceramsite met the national surface water quality requirements.The treatment of domestic sewage showed that the volumetric loads of COD Cr,NH_(4)^(+)-N,and TN removed by the aerated biofilter were 5.23,0.98,and 0.35 kg/(m^(3)·d),respectively,with removal rates of 85.46%,96.13%,and 32.31%.

Combined use of fly ash and silica to prevent the long-term strength retrogression of oil well cement set and cured at HPHT conditions

The long-term strength retrogression of silica-enriched oil well cement poses a significant threat to wellbore integrity in deep and ultra-deep wells, which is a major obstacle for deep petroleum and geothermal energy development. Previous attempts to address this problem has been unsatisfactory because they can only reduce the strength decline rate. This study presents a new solution to this problem by incorporating fly ash to the traditional silica-cement systems. The influences of fly ash and silica on the strength retrogression behavior of oil well cement systems directly set and cured under the condition of 200°C and 50 MPa are investigated. Test results indicate that the slurries containing only silica or fly ash experience severe strength retrogression from 2 to 30 d curing, while the slurries containing both fly ash and silica experience strength enhancement from 2 to 90 d. The strength test results are corroborated by further evidences from permeability tests as well as microstructure analysis of set cement. Composition of set cement evaluated by quantitative X-ray diffraction analyses with partial or no known crystal structure(PONKCS) method and thermogravimetry analyses revealed that the conversion of amorphous C-(A)-S-H to crystalline phases is the primary cause of long-term strength retrogression.The addition of fly ash can reduce the initial amount of C-(A)-S-H in the set cement, and its combined use with silica can prevent the crystallization of C-(A)-S-H, which is believed to be the working mechanism of this new admixture in improving long-term strength stability of oil well cement systems.

Physico-Chemical Characterization of Wood Ash for Agronomic Purposes

The oil refinery of the food products company SOPAL, located in the port area of TOGO, produces an average of 200 kg of eucalyptus wood ash per day. This ash is stored in large quantities within the premises of the refinery, without any disposal solution. The aim of this study is to identify the physico-chemical properties of SOPAL’s wood ash for agronomic valorization. Physico-chemical analyses reveal the presence of major and secondary elements such as potassium (15.71 g/kg DM), phosphorus (27.90 g/kg DM), calcium (9.76 g/kg DM), magnesium (0.03 g/kg DM), sodium (1.24 g/kg DM), iron (1.49 g/kg DM) and manganese (7.82 g/kg DM). The pH is alkaline (12.97) with fairly high conductivity (24.10 mS/Cm). Heavy metals identified are cobalt (0.19 mg/kg DM), cadmium (0.10 mg/kg DM), lead (1.14 mg/kg DM), copper (19.77 mg/kg DM) and nickel (12.82 mg/kg DM). The results show that the ash contains considerable amount of major and secondary elements for agronomic uses.

Incorporating empirical knowledge into data-driven variable selection for quantitative analysis of coal ash content by laser-induced breakdown spectroscopy

Laser-induced breakdown spectroscopy(LIBS)has become a widely used atomic spectroscopic technique for rapid coal analysis.However,the vast amount of spectral information in LIBS contains signal uncertainty,which can affect its quantification performance.In this work,we propose a hybrid variable selection method to improve the performance of LIBS quantification.Important variables are first identified using Pearson's correlation coefficient,mutual information,least absolute shrinkage and selection operator(LASSO)and random forest,and then filtered and combined with empirical variables related to fingerprint elements of coal ash content.Subsequently,these variables are fed into a partial least squares regression(PLSR).Additionally,in some models,certain variables unrelated to ash content are removed manually to study the impact of variable deselection on model performance.The proposed hybrid strategy was tested on three LIBS datasets for quantitative analysis of coal ash content and compared with the corresponding data-driven baseline method.It is significantly better than the variable selection only method based on empirical knowledge and in most cases outperforms the baseline method.The results showed that on all three datasets the hybrid strategy for variable selection combining empirical knowledge and data-driven algorithms achieved the lowest root mean square error of prediction(RMSEP)values of 1.605,3.478 and 1.647,respectively,which were significantly lower than those obtained from multiple linear regression using only 12 empirical variables,which are 1.959,3.718 and 2.181,respectively.The LASSO-PLSR model with empirical support and 20 selected variables exhibited a significantly improved performance after variable deselection,with RMSEP values dropping from 1.635,3.962 and 1.647 to 1.483,3.086 and 1.567,respectively.Such results demonstrate that using empirical knowledge as a support for datadriven variable selection can be a viable approach to improve the accuracy and reliability of LIBS quantification.

Concentration of Copper, Zinc, Lead, Cadmium, and Nickel in the Incinerator Bottom Ash in Five County Hospitals in Kenya

Healthcare wastes contain potentially harmful microorganisms, inorganic and organic compounds that pose a risk to human health and the environment. Incineration is a common method employed in healthcare waste management to reduce volume, quantity, toxicity as well as elimination of microorganisms. However, some of the substances remain unchanged during incineration and become part of bottom ash, such as heavy metals and persistent organic pollutants. Monitoring of pollution by heavy metals is important since their concentrations in the environment affect public health. The goal of this study was to determine the levels of Copper (Cu), Zinc (Zn) Lead (Pb), Cadmium (Cd) and Nickel (Ni) in the incinerator bottom ash in five selected County hospitals in Kenya. Bottom ash samples were collected over a period of six months. Sample preparation and treatment were done using standard methods. Analysis of the heavy metals were done using atomic absorption spectrophotometer, model AA-6200. One-Way Analysis of Variance (ANOVA) was performed to determine whether there were significant differences on the mean levels of Cu, Zn, Pd, Cd and Ni in incinerator bottom ash from the five sampling locations. A post-hoc Tukey’s Test (HSD) was used to determine if there were significant differences between and within samples. The significant differences were accepted at p ≤ 0.05. To standardize the results, overall mean of each metal from each site was calculated. The metal mean concentration values were compared with existing permissible levels set by the WHO. The concentrations (mg/kg) were in the range of 102.27 - 192.53 for Cu, Zn (131.68 - 2840.85), Pb (41.06 - 303.96), Cd (1.92 - 20.49) whereas Ni was (13.83 - 38.27) with a mean of 150.76 ± 77.88 for Copper, 131.66 ± 1598.95 for Zinc, 234.60 ± 262.76 for Lead, 12.256 ± 10.86 for Cadmium and 29.45 ± 18.24 for Nickel across the five sampling locations. There were significant differences between levels determined by one-way ANOVA of Zn (F (4, 25) = 6.893, p = 0.001, p ≤ 0.05) and Cd (F (4, 25) = 5.641, p = 0.02) and none with Cu (F (4, 25) = 1.405, p = 0.261, p ≤ 0.05), Pb (F (4, 25) = 1.073, p = 0.391, p ≤ 0.05) and Ni (F (4, 25) = 2.492, p = 0.069). Results reveal that metal content in all samples exceed the WHO permissible levels for Cu (100 mg/kg), while those for Ni were below the WHO set standards of 50 mg/kg. Levels of Zn in three hospitals exceeded permissible level of 300 mg/kg while level of Pb exceeded WHO set standards of 100 mg/kg in two hospitals. Samples from four hospitals exceeded permissible level for Cd of 3 mg/kg. This study provides evidence that incinerator bottom ash is contaminated with toxic heavy metals to human health and the environment. This study recommends that hospitals should handle the bottom ash as hazardous wastes and there is need to train and provide appropriate personal protective equipment to healthcare workers, waste handlers, and incinerator operators and enforce compliance to existing regulation and guidelines on healthcare waste management to safeguard the environment and human health.

The Influence of Rice Husk Ash on Mechanical Properties of the Mortar and Concrete: A Critical Review

Increasing the population and infrastructure in both emerging and developed countries requires a considerable amount of cement, which significantly affects the environment. The primary materials of concrete (‘cement’) production emit a large quantity of CO2 into the environment. Also, the cost of conventional building materials like cement gives motivation to find geopolymer waste materials for concrete. To reduce harmful effects on the environment and cost of traditional concrete substance, alternative waste materials like rice husk ash (RHA), ground granulated blast-furnace (GGBS), fly ash (FA), and metakaolin (MK) can be used due to their pozzolanic behavior. RHA waste material with a high silica concentration obtained from burning rice husks can possibly be used as a supplementary cementitious material (SCM) in the manufacturing of concrete, and its strong pozzolanic properties can contribute to the strength and impermeability of concrete. This review paper highlights a summary of the positive effect of using RHA as a partial substitute for cement in building construction, as well as its optimal inclusion of enhanced mechanical properties like compressive strength, flexural strength, and split tensile strength of mortar and concrete.

Dry Mix Slag—High-Calcium Fly Ash Binder. Part Two: Durability

This work investigates durability of cement-free mortars with a binder comprised of ground granulated blast furnace slag (GGBFS) activated by high-calcium fly ash (HCFA) and sodium carbonate (Na2CO3): the soundness, sulfate resistance, alkali-silica reactivity and efflorescence factors are considered. Results of tests show that such mortars are resistant to alkali-silica expansion. Mortars are also sulfate-resistant when the amount of HCFA in the complex binder is within a limit of 10 wt%. The fineness of fly ash determines its’ ability to activate GGBFS hydration, and influence soundness of the binder, early strength development, sulfate resistance and efflorescence behavior. The present article is a continuation of authors’ work, previously published in MSA, Vol. 14, 240-254.

三阴性乳腺癌患者ASH2L、HOXA2表达及其与淋巴转移的关系

目的探讨三阴性乳腺癌(TNBC)患者ASH2样蛋白(ASH2L)和同源异型盒A2(HOXA2)的表达及其与淋巴转移的关系。方法选取2016年6月—2020年6月南阳市中心医院TNBC患者80例,收集其癌组织样本;另收集60例配对癌旁组织(距肿瘤边缘≥5 cm)样本作为对照。收集所有患者的临床病理资料,并检测ASH2L、HOXA2 mRNA和蛋白的表达。采用受试者工作特征(ROC)曲线评价ASH2L mRNA、HOXA2 mRNA判断TNBC患者淋巴转移的效能。结果癌组织中ASH2L mRNA、HOXA2 mRNA相对表达量和蛋白阳性率均显著高于癌旁组织(P<0.05)。有淋巴转移、TNM分期Ⅲ~Ⅳ期的TNBC患者癌组织ASH2L蛋白、HOXA2蛋白阳性率分别显著高于无淋巴转移和TNM分期Ⅰ~Ⅱ期的患者(P<0.05)。不同年龄、肿瘤大小、绝经状态的TNBC患者之间癌组织ASH2L蛋白、HOXA2蛋白阳性率差异无统计学意义(P>0.05)。有淋巴转移的TNBC患者癌组织中ASH2L mRNA、HOXA2 mRNA相对表达量显著高于无淋巴转移的患者(P<0.05)。ASH2L mRNA、HOXA2 mRNA单项检测和联合检测诊断TNBC患者淋巴转移的曲线下面积(AUC)分别为0.706、0.791、0.895。结论TNBC患者癌组织中ASH2L、HOXA2 mRNA和蛋白均呈高表达,且与TNM分期和淋巴转移有关。