Preparation of Co/S co-doped carbon catalysts for excellent methylene blue degradation

S and Co co-doped carbon catalysts were prepared via pyrolysis of MOF-71 and thiourea mixtures at 800℃at a mass ratio of MOF-71 to thiourea of 1:0.1 to effectively activate peroxymonosulfate(PMS)for methylene blue(MB)degradation.The effects of two different mixing routes were identified on the MB degradation performance.Particularly,the catalyst obtained by the alcohol solvent evaporation(MOF-AEP)mixing route could degrade 95.60%MB(50 mg/L)within 4 min(degradation rate:K=0.78 min^(-1)),which was faster than that derived from the direct grinding method(MOF-DGP,80.97%,K=0.39 min^(-1)).X-ray photoelectron spectroscopy revealed that the Co-S content of MOF-AEP(43.39at%)was less than that of MOF-DGP(54.73at%),and the proportion of C-S-C in MOF-AEP(13.56at%)was higher than that of MOF-DGP(10.67at%).Density functional theory calculations revealed that the adsorption energy of Co for PMS was -2.94 eV when sulfur was doped as C-S-C on the carbon skeleton,which was higher than that when sulfur was doped next to cobalt in the form of Co-S bond(-2.86 eV).Thus,the C-S-C sites might provide more contributions to activate PMS compared with Co-S.Furthermore,the degradation parameters,including pH and MOF-AEP dosage,were investigated.Finally,radical quenching experiments and electron paramagnetic resonance(EPR)measurements revealed that ^(1)O_(2)might be the primary catalytic species,whereas·O~(2-)might be the secondary one in degrading MB.

Vacancy defect MoSeTe embedded in N and F co-doped carbon skeleton for high performance sodium ion batteries and hybrid capacitors

Sodium-ion batteries(SIBs) and hybrid capacitors(SIHCs) have garnered significant attention in energy storage due to their inherent advantages,including high energy density,cost-effectiveness,and enhanced safety.However,developing high-performance anode materials to improve sodium storage performa nce still remains a major challenge.Here,a facile one-pot method has been developed to fabricate a hybrid of MoSeTe nanosheets implanted within the N,F co-doped honeycomb carbon skeleton(MoSeTe/N,F@C).Experimental results demonstrate that the incorporation of large-sized Te atoms into MoSeTe nanosheets enlarges the layer spacing and creates abundant anion vacancies,which effectively facilitate the insertion/extraction of Na^(+) and provide numerous ion adsorption sites for rapid surface capacitive behavior.Additionally,the heteroatoms N,F co-doped honeycomb carbon skeleton with a highly conductive network can restrain the volume expansion and boost reaction kinetics within the electrode.As anticipated,the MoSeTe/N,F@C anode exhibits high reversible capacities along with exceptional cycle stability.When coupled with Na_(3)V_(2)(PO_(4))_(3)@C(NVPF@C) to form SIB full cells,the anode delivers a reversible specific capacity of 126 mA h g^(-1) after 100 cycles at 0.1 A g^(-1).Furthermore,when combined with AC to form SIHC full cells,the anode demonstrates excellent cycling stability with a reversible specific capacity of50 mA h g^(-1) keeping over 3700 cycles at 1.0 A g^(-1).In situ XRD,ex situ TEM characterization,and theoretical calculations(DFT) further confirm the reversibility of sodium storage in MoSeTe/N,F@C anode materials during electrochemical reactions,highlighting their potential for widespread practical application.This work provides new insights into the promising utilization of advanced transition metal dichalcogenides as anode materials for Na^(+)-based energy storage devices.

Visible light induced photodegradation of organic pollutants on nitrogen and fluorine co-doped TiO_2 photocatalyst

The nitrogen and fluorine co doped TiO 2 polycrystalline powder was synthesized by calcinations of the hydrolysis product of tetra butyl titanate with ammonium fluoride. Nitrogen and fluorine co doping causes the absorption edge of TiO 2 to shift to a lower energy region. The photocatalytic activity of co doped TiO 2 with anatase phases was found to be 2 4 times higher than that of the commercial TiO 2 photocatalyst Degussa P25 for phenol decomposition under visible light irradiation. The co doped TiO 2 powders only contain anatase phases even at 1000℃. Apparently, ammonium fluoride added retarded phase transformation of the TiO 2 powders from anatase to rutile. The substitutional fluorine and interstitial nitrogen atoms in co doped TiO 2 polycrystalline powder were responsible for the vis light response and caused the absorption edge of TiO 2 to shift to a lower energy region.

Preparation, Characterization and Photocatalytic Activity of Fe, La Co-doped Nanometer Titanium Dioxide Photocatalysts

A series of photocatalysts of un-doped, single-doped and co-doped nanometer titanium diox- ide （TiO2） have been successfully prepared by template method using Fe（NO3）3.9H2O, La（NO3）3.6H2O, and tetrabutyl titanate as precursors and glucan as template. Scanning electron microscopy, X-ray diffraction, and N2 adsorption-desorption measurement were employed to characterize the morphology, crystal structure and surface structure of the samples. The photo-absorbance of the obtained catalysts was measured by UV-Vis absorption spectroscopy, and the photocatalytic activities of the prepared samples under UV and visible light were estimated by measuring the degradation rate of methyl orange in an aqueous solution. The characterizations indicated that the prepared photocatalysts consisted of anatase phase and possessed high surface area of ca. 163-176 m2/g. It was shown that the Fe and La co-doped nano-TiO2 could be activated by visible light and could thus be used as an effective catalyst in photo-oxidation reactions. The synergistic effect of Fe and La co-doping played an important role in improving the photocatalytic activity. In addition, the possibility of cyclic usage of co-doped nano-TiO2 was also confirmed, the photocatalytic activity of codoped nano-TiO2 remained above 89.6% of the fresh sample after being used four times.

Preparation of nitrogen and sulfur co-doped ultrathin graphitic carbon via annealing bagasse lignin as potential electrocatalyst towards oxygen reduction reaction in alkaline and acid media

Renewable lignin used for synthesizing materials has been proven to be highly potential in specific electrochemistry.Here,we report a simple method to synthesize nitrogen and sulfur co-doped carbon nanosheets by using bagasse lignin,denoted as lignin-derived carbon(LC).By adjusting the ratio of nitrogen source and annealing temperature,we obtained the ultrathin graphitic lignin carbon(LC-4-1000)with abundant wrinkles with high surface area of 1208 m2g_1 and large pore volume of 1.40 cm3g_1.In alkaline medium,LC-4-1000 has more positive half-wave potential and nearly current density compared to commercial Pt/C for oxygen reduction reaction(ORR).More importantly,LC-4-1000 also exhibits comparable activity and superior stability for ORR in acid medium due to its high graphitic N ratio and a direct four electron pathway for ORR.This study develops a cost-effective and highly efficient method to prepare biocarbon catalyst for ORR in fuel cells.

Synthesis and Characterization of Co-Doped Brookite Titania Photocatalysts with High Photocatalytic Activity

Transition metal-doping could effectively extend the light response range of TiO _2 photocatalysts from the ultraviolet(UV)to the visible region.Co-doped brookite titanium dioxide(Co–TiO_2)photocatalysts were synthesized via the hydrothermal method with titanium tetrachloride as the raw material and cobalt chloride hexahydrate as the dopant.The prepared Co–TiO_2 photocatalysts were characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM),transmission electron microscopy(TEM),Raman spectroscopy,X-ray photoelectron spectroscopy(XPS)and UV–Vis diffuse reflectance spectroscopy(UV–Vis DRS).The photocatalytic activities of Co–TiO _2 photocatalysts were evaluated by photocatalytic degradation of isopropanol alcohol(IPA),a typical volatile organic compound(VOC),under visible light.The influences ofdifferent Co doping rates,initial concentrations of IPA gas and the amounts of photocatalyst addition were also studied.At the same time,the enhancement mechanism ofcobalt ions as a trap for photogenerated holes was discussed.Thus,we found the optimum doping rate,initial concentration of IPA gas and amount of photocatalyst to add.The results show that the mesoporous Co–TiO _2 photocatalysts possess smaller size particles,larger specific surface area,lower forbidden bandgap energy(Eg)and better photocatalytic activity than pure brookite TiO _2.When the doping of Co was 7% by mass,the initial concentration ofIPA gas was 1.0×10^(-6 )mol/L and the addition of Co–TiO_2 photocatalysts was 50 mg,the best photocatalytic activity was achieved.Furthermore,the degradation rate ofIPA was up to 91%,which shows great potential for waste water treatment.

Construction of nitrogen and phosphorus co-doped graphene quantum dots/Bi5O7I composites for accelerated charge separation and enhanced photocatalytic degradation performance

Nitrogen and phosphorus co-doped graphene quantum dot-modified Bi5O7 I(NPG/Bi5O7 I)nanorods were fabricated via a simple solvothermal method.The morphology,structure,and optical properties of the as-prepared samples were investigated by X-ray diffraction,scanning electron microscopy,high-resolution transmission electron microscopy,X-ray photoelectron spectroscopy(XPS),and diffused reflectance spectroscopy.The photocatalytic performance was estimated by degrading the broad-spectrum antibiotics tetracycline and enrofloxacin under visible light irradiation.The photodegradation activity of Bi5O7 I improved after its surface was modified with NPGs,which was attributed to an increase in the photogenerated charge transport rate and a decrease in the electron-hole pair recombination efficiency.From the electron spin resonance spectra,XPS valence band data,and free radical trapping experiment results,the main active substances involved in the photocatalytic degradation process were determined to be photogenerated holes and superoxide radicals.A possible photocatalytic degradation mechanism for NPG/Bi5O7 I nanorods was proposed.

Synthesis of boron, nitrogen co-doped porous carbon from asphaltene for high-performance supercapacitors

Oxidized asphaltene （OA）, a thermosetting material with plenty of functional groups, is synthesized from asphaltene （A） using HNO3]HzSO4 as the oxidizing agent. Boron, nitrogen co-doped porous carbon （BNC-OA） is prepared by carbonization of the mixture of boric acid and OA at 1173 K in an argon atmosphere. X-ray photoelectron spectroscopy （XPS） characterization reveals that the BNC-OA has a nitrogen content of 3.26 at.% and a boron content of 1.31 at.%, while its oxidation-free counterpart （BNC-SA） has a nitrogen content of 1.61 at.% and a boron content of 3.02 at.%. The specific surface area and total pore volume of BNC-OA are 1103 m2·g^-1 and 0.921 cm3·g^-1, respectively. At a current density of 0.1 A·g^-1, the specific capacitance of BNC-OA is 335 F·g^-1 and the capacitance retention can still reach 83% at 1 A·g^-1. The analysis shows that the superior electrochemical performance of the BNC-OA is attributed to the pseudocapacitance behavior of surface heteroatom functional groups and an abundant pore-structure. Boron, nitrogen co-doped porous carbon is a promising electrode material for supercapacitors.

Structure, photocatalytic and antibacterial activity study of Meso porous Ni and S co-doped TiO2 nano material under visible light irradiation

Undoped and Ni–S co-doped mesoporous TiO2 nano materials were synthesized by using sol–gel method.The characteristic features of as prepared catalyst samples were investigated using various advanced spectroscopic and analytical techniques.The characterization results of the samples revealed that all the samples exhibited anatase phase(XRD),decreasing band gap(2.68 eV)(UV–Vis-DRS),small particle size(9.2 nm)(TEM),high surface area(142.156 m^2·g^-1)(BET),particles with spherical shape and smooth morphology(SEM);there is a frequency shift observed for co-doped sample(FT-IR)and the elemental composition electronic states and position of the doped elements(Ni and S)in the TiO2 lattice analyzed by XPS and EDX.These results supported the photocatalytic degradation of Bismarck Brown Red(BBR)achieved with in 110 min and also exhibited the antibacterial activity on Staphylococcus aureus(MTCC-3160),Pseudomonas fluorescence(MTCC-1688)under visible light irradiation.

Difference in magnetic properties between Co-doped ZnO powder and thin film

This paper reports that the Zn0.95Co0.05O polycrystalline powder and thin film were prepared by sol-gel technique under the similar preparation conditions. The former does not show typical ferromagnetic behaviour, while the latter exhibits obvious ferromagnetic properties at 5 K and room temperature. The UV-vis spectra and x-ray absorption spectra show that Co2＋ ions are homogeneously incorporated into ZnO lattice without forming secondary phases.The distinct difference between film and powder sample is the c-axis （002） preferential orientation indicated by the x-ray diffraction pattern and field emission scanning electron microscopy measurement, which may be the reason why Zn0.95Co0.05O film shows ferromagnetic behaviour.

Optical temperature sensor based on up-conversion fluorescence emission in Yb^(3+):Er^(3+) co-doped ceramics glass

yb^3＋：Er^3＋ co-doped oxy-fluoride ceramics glass has been prepared. The mechanism of up-conversion emissions about Er^3＋ was discussed, and the temperature properties of green up-conversion fluorescence between 303 and 823 K were investigated. The results show that the sensitivity of this sample reaches its maximum value, about 0.0047 K^-1, when the temperature is 383 K, indicating that this kind of sample can be used as high temperature and high sensitivity optical temperature sensor.

Nitrogen and Sulfur Co-doped Porous Carbon Derived from ZIF-8 as Oxygen Reduction Reaction Catalyst for Microbial Fuel Cells

Nitrogen and sulfur co-doped porous nanocarbon (ZIF-C-N-S) catalyst was successfully synthesized derived from ZIF-8 and thiourea precursors.The electrochemical measurements indicate that the as-obtained ZIF-C-N-S catalyst exhibits higher electrocatalytic activity for oxygen reduction reaction (ORR) in alkaline electrolyte and superior durability-longer than commercial Pt/C catalyst.The enhancment of electrocatalytic activity mainly be come from the open pore structure,large specific surface area as well as the synergistic effect resulted from the co-doping of N and S atoms.In addition,the ZIF-C-N-S catalyst is also used as the air cathode catalyst in the microbial fuel cell (MFC) device.The maximum power density and stable output voltage of ZIF-C-N-S based MFC are 1315 mW/m2 and 0.48 V,respectively,which is better than that of Pt/C based MFC.

Sustainable silicon anodes facilitated via a double-layer interface engineering: Inner SiOx combined with outer nitrogen and boron co-doped carbon

Silicon-based(Si)materials are promising anodes for lithium-ion batteries(LIBs)because of their ultrahigh theoretical capacity of 4200 mA h g^(−1).However,commercial applications of Si anodes have been hindered by their drastic volume variation(∼300%)and low electrical conductivity.Here,to tackle the drawbacks,a hierarchical Si anode with double-layer coatings of a SiOx inner layer and a nitrogen(N),boron(B)co-doped carbon(C-NB)outer layer is elaborately designed by copyrolysis of Si-OH structures and a H3BO_(3)-doped polyaniline polymer on the Si surface.Compared with the pristine Si anodes(7mA h g^(−1) at 0.5 A g^(−1) after 340 cycles and 340 mA h g^(−1) at 5 A g^(−1)),the modified Si-based materials(Si@SiOx@C-NB nanospheres)present su perior cycling stability(reversible 1301 mA h g^(−1) at 0.5 A g^(−1) after 340 cycles)as well as excellent rate capability(690mA h g^(−1) at 5 A g^(−1))when used as anodes in LIBs.The unique double-layer coating structure,in which the inner amorphous SiOx layer acts as a buffer matrix and the outer defect-rich carbon enhances the electron diffusion of the whole anode,makes it possible to de liver excellent electrochemical properties.These results indicate that our double-layer coating strategy is a promising approach not only for the devel opment of sustainable Si anodes but also for the design of multielement-doped carbon nanomaterials.

Electronic Structure Magnetic Properties and Optical Properties of Co-doped AIN from First Principles

The electronic structure, magnetic properties, and optical properties of Co-doped AIN are investigated based upon the Perdew-Burke-Ernzerhof form of generalized gradient approximation within the density functional theory. The band gaps narrowing of AI1-x Cox N are found with the increase of Co concentrations. The analyses of the band structures and density of states show that AI1-xCoxN alloys exhibit a halfometallie character. Moreover, we have succeeded in demonstrating that Co doped AIN system in x = 0.125 is always antiferromagnetie, which is in good agreement with the experimental results. Besides, it is shown that the insertion of Co atom leads to redshift of the optical absorption edge. Finally, the optical constants of pure A1N and AI1-xCoxN alloy, such as loss function, refractive index and reflectivity, are discussed.

Construction of N,O co-doped carbon anchored with Co nanoparticles as efficient catalyst for furfural hydrodeoxygenation in ethanol

Hydrodeoxygenation of furfural(FF)into 2-methylfuran(MF)is a significant biomass utilization route.However,designing efficient and stable non-noble metal catalyst is still a huge challenge.Herein,we reported the N,O co-doped carbon anchored with Co nanoparticles(Co-SFB)synthesized by employing the organic ligands with the target heteroatoms.Raman,electron paramagnetic resonance(EPR),electrochemical impedance spectroscopy(EIS),and X-ray photoelectron spectroscopy(XPS)characterizations showed that the co-doping of N and O heteroatoms in the carbon support endows Co-SFB with enriched lone pair electrons,fast electron transfer ability,and strong metal-support interaction.These electronic properties resulted in strong FF adsorption as well as lower apparent reaction activation energy.At last,the obtained N,O co-doped Co/C catalyst showed excellent catalytic activity(nearly 100 mol%FF conversion and 94.6 mol%MF yield)and stability for in-situ dehydrogenation of FF into MF.This N,O co-doping strategy for the synthesis of highly efficient catalytic materials with controllable electronic state will provide an excellent opportunity to better understand the structure-function relationship.

High-loading Co-doped NiO nanosheets on carbon-welded carbon nanotube framework enabling rapid charge kinetic for enhanced supercapacitor performance

Developing high power and energy supercapacitors(SCs)is a long-pursued goal for the application in transportation and energy storage station.Herein,a rationally-designed Co-doped nickel oxide nanosheets@carbon-welded carbon nanotube foam(Co-doped NiO@WCNTF)as freestanding electrode is successfully prepared for high power and energy SCs.The WCNTF framework with high specific surface area provides three dimensional highly conductive network for fast charge transport and ensures high loading of active materials(9.2 mg/cm2).Moreover,porous Co-doped NiO nanosheets uniformly anchored on the WCNTF framework enable rapid charge kinetics due to the high intrinsic conductivity of Co-doped Ni O nanosheets and their good contact with conductive WCNTF substrate.As a result,the unique integrated electrode with 3D architecture exhibits an ultrahigh specific capacitance of 11.45 F/cm2 at 5 mA/cm2,outstanding rate capability(11.45 F/cm2 at 5 mA/cm2 and a capacitance retention of 86.2%at 30 mA/cm2)and good cycling stability,suggesting great potential for high performance supercapacitor.

Spectral and Lasing Properties of Er^(3+0/Yb^(3+) Co-Doped Phosphate Glasses Pumped by LD

Er^3 ＋/Yb^3 ＋ phosphate glasses were fabricated. According to McCumber theory, the stimulated emission cross-section of Er^3＋ ions at 1533 nm was calculated on the basis of absorption spectrum, and 0.84 × 10^-20 cm^2 is derived, the fluorescence lifetime of ^4I13/2 level is 8.5 ms. An Er^3＋/Yb^3＋ co-doped phosphate glass CW laser pumped by LD was demonstrated at room temperature. The maximum output power is 80 mW and slope efficiency is 16.5%.

Intense up-conversion emissions of yb3＋/Dy3＋ co-doped A12O3 nanopowders prepared by non-aqueous sol-gel method＊

yb3＋/Dy3＋ co-doped A1203 nanopowders have been prepared by the non-aqueous sol-gel method and their up- conversion photoluminescence spectra are measured under excitation by a 980-nm semiconductor laser. The results show that there are comparatively abundant spectra of up-conversion emissions centered at 378, 408, 527 and 543, and 663 nm, corresponding to 4C9/2→ 6H13/2, 4C9/2→ 6Hll/2, 4115/2 → 6H13/2, and 4F9/2 →6Hll/2 transitions of Dy3＋, respectively. Two-photon and three-photon processes are involved in ultraviolet, violet, green, and red up-conversion emissions. The energy transition between Yb3＋ and Dy3＋ is discussed.

Spectroscopic properties and mechanism of Tm^(3+)/Er^(3+)/Yb^(3+) co-doped oxyfluorogermanate glass ceramics containing BaF_2 nanocrystals

Transparent Tm^3＋/Er^3＋/yb^3＋ co-doped oxyfluorogermanate glass ceramics containing BaF2 nanocrystals are prepared. Under excitation of a 980-nm laser diode （LD）, compared with the glass before heat treatment, the Tm^3＋/Er^3＋/yb^3＋ co-doped oxyfluorogermanate glass ceramics can emit intense blue, green and red up-conversion luminescence and Stark- split peaks; X-ray diffraction （XRD） and transmission electron microscope （TEM） results show that BaF2 nanocrystals with an average diameter of 20 nm are precipitated from the glass matrix. Stark splitting of the up-conversion luminescence peaks in the glass ceramics indicates that Tm^3＋, Er^3＋ and （or） Yb^3＋ ions are incorporated into the BaF2 nanocrystals. The up-conversion luminescence intensities of Tm^3＋, Er^3＋ and the splitting degree of luminescence peaks in the glass ceramics increase significantly with the increase of heat treat temperature and heat treat time extension. In addition, the possible energy transfer process between rare earth ions and the up-conversion luminescence mechanism are also proposed.

Photocatalysis Activity and Physicochemical Structure of Titanium Dioxide Co-doped with N and B

Titanium dioxide co-doped with N and B was prepared by sol-gel method. The photocatalytic activity was evaluated by the photodegradation of methylene blue under visible light. Its physicochemical properties were characterized by means of UV-Vis DRS, XRD, PT-IR, and XPS. The results indicated that N-B-TiO2 has good activity to the photodegradation of MB. Its decolourizing rate of methylene blue solution goes up to 98.4% under the visible light irradiation with 5 h. The doping nitrogen forms N-Ti-O and boron primarily existing in oxide appears in the N-B-TiO2 sample. They response for visible light of TiOa was also exploited.